Cisco IR800 Series Hardware Installation Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. IR800 Series
  6. Hardware installation manual
Cisco IR800 Series Hardware Installation Manual

Cisco IR800 Series Hardware Installation Manual

Industrial integrated services router
Hide thumbs
Table of Contents

Quick Links

Cisco IR807 Industrial Integrated Services Router Hardware Installation
Guide
First Published: 2017-11-10
Last Modified: 2018-10-12
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Table of Contents
loading

Related Manuals for Cisco IR800 Series

Summary of Contents for Cisco IR800 Series

  • Page 1 Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide First Published: 2017-11-10 Last Modified: 2018-10-12 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883...
  • Page 2 Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com...
  • Page 3 Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...

  • Page 4: Safety Warnings

    éviter les accidents. Pour prendre connaissance des tradu avertissements figurant dans les consignes de sécurité traduites qui accompagnent ce référez-vous au numéro de l'instruction situé à la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS Danger Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 5 Al final de cada advertenc número que le ayudará a encontrar el texto traducido en el apartado de traduccione a este dispositivo. Danger GUARDE ESTAS INSTRUCCIONES Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 6 Använd det nummer som fi av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som denna anordning. SPARA DESSA ANVISNINGAR Danger Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 7 Brug erklæringsnummeret efter hver advarsel for at find i de oversatte advarsler, der fulgte med denne enhed. Danger GEM DISSE ANVISNINGER Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 8 Preface Safety Warnings Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 9 Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO. The use of cables that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited to CISCO-designated products.

  • Page 10: Searching Cisco Documents

    Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation , which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html...

  • Page 11: Product Overview

    C H A P T E R Product Overview This chapter provides an overview of the features available for the Cisco 807 Integrated Services Routers (ISRs) and contains the following sections: • Product Overview, on page 9 Product Overview This chapter provides an overview of the features available for the Cisco 807 Integrated Services Routers...
  • Page 12 Slow Flash is defined as the LED will be on for 0.25 seconds and off for 0.75 seconds.Fast Flash is defined as the LED will be on for 0.25 seconds and off for 0.25 seconds. Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 13 On - Green Green > -60dBm On - On - On - Green Green Green Table 4: Icons only Icon Description Icon Description Console USB 2.0 Type A Port for Storage and Networking Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 14 Serial Ports Fast Ethernet Ports Antenna 1 (TNC) Main Antenna 1 (TNC) Div Warning Figure 1: Cisco IR807 Front Panel, on page 13shows the front panel details of the Cisco IR807. Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 15 FE0 10/100 Base-T RJ-45 External DC Power Input and Alarm GPS (SMA) Figure 2: Cisco IR807 Back Panel, on page 13 shows the back panels details of the Cisco IR807. Figure 2: Cisco IR807 Back Panel Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...

  • Page 16: Hardware Features

    SIM0 (bottom) and SIM1 (top) Slots Memory The Cisco IR807 uses flash memory and main memory. The flash memory contains the Cisco IOS software image and the boot flash contains the ROMMON boot code. All memory components are factory default and not upgradeable by the end user.

  • Page 17: Supported Cisco Antennas And Cables

    NOTE: Before choosing your antenna type and installation scenario, read through the following information. Supported Cisco Antennas and Cables The following section lists the supported Antennas and Cables for the Cisco IR807. For detailed information about Cisco Antennas, please refer to the following guides: Cisco Industrial Routers and Industrial Wireless Access Points Antenna Guide: http://www.cisco.com/c/en/us/td/docs/routers/connectedgrid/antennas/installing-combined/industrial-routers-and-industrial-wireless-antenna-guide.html...
  • Page 18 • Maximum power: 10W • Radome: Polycarbonate, UV, black • Material substance compliance: ROHS compliant ANT-4G-OMNI-OUT-N Description: Cisco outdoor omnidirectional antenna for 2G, 3G, and 4G LTE cellular • UV-stable radome • Mast-mounting bracket • Applicable for both 2G and 3G solutions •...
  • Page 19 • Wind rating: 160 km/H • IP rating: IP54 • Radome: polycarbonate, UV resistant, white • Material substance compliance: ROHS compliant ANT-4G-SR-OUT-TNC Description - Cisco integrated 4G LTE low-profile outdoor saucer antenna: Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 20 • Peak gain: 0.5 dBi (698 to 960 MHz) and 2.2 dBi (1710 to 2700 MHz) • Average efficiency: 55% (698 to 960 MHz) 73% (1710 to 2700 MHz) • Maximum input power: 3 watts • Voltage standing wave ratio (VSWR): < 2.5:1 Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 21 • Frequency range: 698 to 960 MHz and 1710 to 2700 MHz • Gain: 2.5 dBi • Maximum power: 3W • Connector: SMA with TNC male adapters, and SMA for GPS • VSWR: < 2.5:1 Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 22 4G-LTE-ANTM-D Description: • Omnidirectional dipole antenna is designed for indoor use with Cisco 4G and Cisco 3G wireless Integrated Services Routers Generation 2 systems • Articulating Joint —It can be rotated 360 degrees and is capable of maneuvering into three stop positions: 0 degrees, 45 degrees, and 90 degrees.

  • Page 23: Modem Support

    • Weight: 6 oz. (0.17 kg) • Cable: 10 ft. (304.8 cm) non-plenum rated Pro-Flex Plus 195 Modem Support The Cisco IR807 uses the WP7502, WP7504, and WP7601 series modems. The software download page can be found here: https://software.cisco.com/download/navigator.html?mdfid=286288566&flowid=76082 Region/Carrier...

  • Page 24: Power Supply

    2600 MHz (band 7) Power Supply The Cisco IR807 comes with an external DC power connector. The 4-pin power entry connector (receptacle) is mounted to the unit. The 4-pin power entry mating connector (plug) is attached to the receptacle. It is removed during installation and used to connect to the DC power source, then reattached to provide power to the unit.

  • Page 25: Rj45 Ports

    The RS232 DTE pin out applies to both serial 0 and serial 1. This port is not shared with the Console port. Note: The RS232 DTE pin out is different from the Cisco standard Console/Auxiliary port. The following figure shows the characteristics of the S0 and S1 ports:...
  • Page 26 • Depending on your particular model of the router, there will be either a single hole or double hole grounding. • 53-100629-01 - Contains Getting started with the Cisco 807 Integrated Services Router document, associated hardware, and the single hole grounding kit.

  • Page 27: Installing The Router

    Cable Distribution System. This product may connect to the Cable Distribution System ONLY through a device that is approved for direct connection. Statement 1078 Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...

  • Page 28: Equipment, Tools, And Connections

    (NIC) for connecting to Ethernet ports. Installing the Router This section describes how to install the Cisco 807 ISR. This router can be installed on a table top or other flat horizontal surface, mounted on a wall, or DIN rail.
  • Page 29 Two USIM sockets are provided with easy access via a secured panel on the back side of the router. The SIM Slots will be connected directly to the 4G radio. Note: The IR800 series of routers use the Mini-SIM (2FF). Specifications are: • ISO/IEC 7810:2003, ID-000 •...

  • Page 30: Installing Antennas

    1. If SIM card is present, then push the SIM card to eject it out of the slot. Install the new SIM card by pushing it into the slot until you hear a clicking sound. 2. Replace the protective cover and the screws. Modems The Cisco IR807 uses the WP7502, WP7504, and WP7601 series modems: Product Carrier/Region Modem...
  • Page 31 Mounting on a Wall, Table, or Other Flat Surface The Cisco IR807 can be mounted in a vertical or horizontal orientation. It can be mounted to a wall or other flat surface, and can also be mounted to a DIN rail.

  • Page 32: Installing A Din Rail

    IR807-DINRAIL(=) for horizontal mounting, and IR807-VM-DINRAIL(=) for vertical mounting. To attach the DIN rail bracket to the Cisco IR807, follow these steps. Mounting the DIN Rail Bracket on the Router 1. First, attach the DIN rail bracket to the back of the router. The DIN rail bracket mounts in two different ways, depending on the orientation you wish to use.
  • Page 33 2. Once the bracket is attached to the router, it can be mounted onto the DIN Rail. Attaching the Bracket onto the DIN Rail To attach the Cisco IR807 with the bracket to a DIN rail, follow these steps. Refer to Figure 7: Attaching the Bracket to the DIN Rail, on page 32 for details.

  • Page 34: Installing The Router Ground Connection

    CAUTION: Cable distribution system should be grounded (earthed) in accordance with ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable. To install the ground connection, follow these steps: Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 35 3.5 in-lb (0.4 N-m). Attach the other end of the ground wire to a grounded bare metal surface, such as a ground bus, a grounded DIN rail, or a grounded bare rack. Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 36 Installing the Router Installing the Router Ground Connection Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...

  • Page 37: Connecting The Router

    C H A P T E R Connecting the Router This chapter describes how to connect Cisco IR807 Integrated Services Router to Ethernet devices and a network. • Connecting the Router, on page 35 Connecting the Router This chapter describes how to connect Cisco IR807 Integrated Services Router to Ethernet devices and a network.

  • Page 38: Connecting To Dc Power

    Plugs and Pin-Outs The IR807 ships with a DC power accessory kit. The power entry receptacle is on the IR807. The pin-outs are shown in Figure 9: Power Connector Pin-Outs, on page Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 39 NOTE: Your connector may not have the labels V RT A A. In the labeled connector, the pins are: V—Positive DC power connection RT— Return DC power connection A— Alarm Common A— Alarm Input Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 40 Only wire with insulation should extend from the connector. NOTE: Use the same method for wiring the alarm connections. 1—Power connector captive screws Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...

  • Page 41: Verifying Connections

    To verify that all devices are properly connected to the router, first turn on all the connected devices, then check the LEDs. To verify router operation, refer to the Front Panel Icons and LEDs, page 10 Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 42 Connecting the Router Verifying Connections Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...

  • Page 43: Technical Specifications

    NOTE: For compliance and safety information, see the Regulatory Compliance and Safety Information for Cisco IR800 Series Routers. Router Specifications The following information lists the operational limits of the Cisco IR807. Operating the router outside of the limits specified is not supported. Physical Characteristics Table 6:...
  • Page 44 EN301 489-1, EN 303 413, EN 301 489-19, EN 301 489-52, and EN 62311 Table 10: Transportation/Storage Conditions Description Design Specification Temperature -40 to +85°C (–40 to +185°F) Humidity 10 – 95% Altitude 4570 m (15,000 ft) Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 45 • UL/CSA 60079-0, -15 (Class I, Zone 2, Gas groups IIC) • IEC 60079-0, -15 IECEx test report • EN 60079-0, -15 ATEX certification (Class I, Zone 2, Gas groups IIC) Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...
  • Page 46 Technical Specifications Router Specifications Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide...

This manual is also suitable for:

Ir807

Table of Contents