Sharp INSIGHTRANGEHOOD KB-0333K Installation Instructions And Operation Manual
Sharp ventilation hood - chimney range hood user manual
Hide thumbs
Also See for INSIGHTRANGEHOOD KB-0333K:
- Installation instructions & operating manual (36 pages)
Table of Contents
Related Manuals for Sharp INSIGHTRANGEHOOD KB-0333K
Summary of Contents for Sharp INSIGHTRANGEHOOD KB-0333K
- Page 1 KB-0333K...
-
Page 2: For Customer Assistance
MODEL NUMBER DATE OF PURCHASE DEALER SERVICER TO PHONE: DIAL 1-800-BE-SHARP (237-4277) for: SERVICE (for your nearest Sharp Authorized Servicer) PARTS (for your authorized parts distributor) DIAL 1-800-642-2122 for: Charcoal Filters (model KBK-330) TO WRITE: Sharp Electronics Corporation Customer Assistance Center... -
Page 3: Consumer Limited Warranty
Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incident or consequential economic or property damage. -
Page 4: Important Safety Instructions
SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact Sharp at the address or telephone number listed on page 2 of this manual. 2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. -
Page 5: Prepare Hood Location
Determine whether hood will discharge vertically (3 1⁄4” x 10” or 7” round), horizontally (3 1⁄4” x 10” only) or be non-ducted. For vertical or horizontal discharge, run ductwork between the hood location and a roof cap or wall cap. For best results, use a minimum number of transitions and elbows. -
Page 6: Prepare The Hood
PREPARE THE HOOD Remove 7” Round Duct Plate from top of hood. Set duct plate aside - with mounting screws. R e m o v e t a p e holding Filters in place. Pull down on filter tabs or finger holes and lift filters out. - Page 7 Re-install air chute and screw, re-connect wire harness and replace light panel. Note: Be careful not to trap wires between Support Fin and light panel. Remove appropriate Duct Knockout(s) from top or back of hood. Horizontal Discharge Only: Remove the Plate in front of the horizontal discharge knockout.
-
Page 8: Connect Wiring
PREPARE THE HOOD Non-Ducted Installations Only: Requires a Performance Ring to be attached to the blower wheel. The Performance Ring is packed behind the Teflon Coated Bottom Cover. To install ring: Remove Retaining Ring using a flat blade screwdriver. Set aside for later. Remove the Blower Wheel by rocking it side to side and applying a slight force to pull wheel from motor. -
Page 9: Install Hood
If hood is to be installed Non-Ducted: • Purchase a set of (2) charcoal filters, model KBK-330, from your local distributor, retailer or from Sharp (see page 2). INSTALL HOOD Install (2) PAR20, 50 W Maximum Halogen Bulbs or (2) R16, 40 W Maximum Incandescent Bulbs. -
Page 10: Filter Change Indicator
Shack, Digikey (1-800-344-4539), and most electronic supply stores have them in stock. HEAT SENSOR Your Sharp Insight Range Hood is equipped with an advanced Heat Sensor. The Sensor monitors the temperature and automatically adjusts the fan to the appropriate setting. - Page 11 To reduce the risk of electric shock, discon- WARNING nect from power supply before cleaning. Clean frequently using hot Aluminum mesh filters: water and a mild detergent. Filters are dishwasher safe. Charcoal filters (additional filters for non- Clean filter surfaces frequently ducted installations): with a damp cloth and a mild detergent.
- Page 12 – This symbol on the nameplate means the product is listed by Underwriters Laboratories, Inc. SHARP ELECTRONICS CORPORATION • Sharp Plaza, Mahwah, New Jersey 07430-2135 PRINTED IN USA 626 9 9 5B...