Related Manuals for Eckman EKPWT1
Summary of Contents for Eckman EKPWT1
- Page 1 2-STROKE WHEELED PETROL GRASS TRIMMER MODEL EKPWT1 INSTRUCTION MANUAL PLEASE READ AND SAVE THE INSTRUCTION MANUAL FOR FUTURE REFERENCE Any questions please call the Eckman helpline on：0844 441 3011 or go to www.eckman.co.uk...
-
Page 2: Table Of Contents
CONTENTS Application………………………………………………………3 Specifications…………………………………………………..3 Safety Definitions………………………………………………4 General Safety Rules…………………………………………4-6 Parts Identification……………………………………………6-7 Assembly................7-9 Operating………………………………………………....9-12 Storage and maintenance...………………………....12-14 Guarantee………………………………………………………..14 CE Declaration of Conformity..........15 Exploded View and Parts List..........16-18... -
Page 3: Application
This equipment is intended for domestic purposes only for grass trimming and brush cutting . Industrial usage is not covered by this warranty. Specifications Eckman Model EKPWT1 Dimensions 495x 505x 320mm Gross Weight/Net Weight 15kg/13.5kg... -
Page 4: Safety Definitions
General Safety Rules This power unit and accessories can be dangerous! When using the unit and accessories, follow basic safety precautions including the following which should always be followed to reduce the risk or serious personal injury and damage to the unit. Read all these instructions before operating this product and save these... - Page 5 instructions. Be thoroughly familiar with the controls and the proper use of the unit. Never allow children to operate this unit. Warning: Keep children, bystanders, and animals 50 feet (15 meters) away. If approached stop the unit immediately. Warning: Sound pressure level emitted by the machinery is 91.5dB(Brush Cutter)and 93.7dB(Grass Trimmer) when in operation.
-
Page 6: Parts Identification
plug whilst the engine is running. 20. DO NOT SMOKE while refueling and operating equipment. 21. DO NOT OPERATE THE MACHINE WITHOUT THE SILENCER OR AIR FILTER properly installed. 22. DO NOT TOUCH the exhaust when the engine is running. Waiting for the engine to cool down. -
Page 7: Assembly
Line Cutting Head Handle Grip Plastic Guard Fuel Cap Brush Cutter Blade Fuel Tank Throttle Switch Training Wheel Engine Stop Switch Driving Wheel Frame Securing Knob Choke Lever Lower Handle Recoil Starter Top Handle Primer Bulb Locknut Assembly Unpack and make sure no parts are missing. All the screws are pre-fixed to the machine. -
Page 8: Assembly
Connect the top handle to the lower handle using two knobs supplied.(see Fig.4) knob Fig.4 Fitting Plastic Guard Unscrew the bolts on the chromed metal guard holder and mount on the plastic guard, line up the holes then fix and tighten.(see Fig.5 and Fig 6) Fig 5 Fig 6 Fitting Brush Cutter Blade... -
Page 9: Operating
2. Mount blade retainer and grass trimmer head, hand tighten it securely.(see Fig.8) Blade retainer Fig.8 WARNING! Do not use the line cutting head without the plastic guard. Note: Please store the blade retainer and nut in a safe place. Straps supplied are used to fasten throttle cable to handle , to avoid interference during operation. - Page 10 fuel lines and other engine parts. STARTING THE ENGINE: “cold start” 1.Move the choke lever upwards to the position.(see Fig.9) (Note: This is not required if the engine is already warm.) Fig.9 2.Press the primer button 8 times, until the petrol flows in and out of the discharge hose located above the fuel tank.(see Fig.10) Fig.10 3.Pull the recoil starter 2-3 times until you hear the engine has “Bomb”...
- Page 11 Fig.12 5. Pull on the recoil starter once again. Allow the engine to run idle for around 10 seconds to let it warm up. 6. To speed up, set the Throttle Switch to the “H” position. Fig.13 Note: Check the blade to make sure it does not turn when the engine is at idle. If the blade rotates even a little, using a Philips head screwdriver, lower the idling speed by adjusting the carburetor as shown below.
-
Page 12: Storage And Maintenance
3.The engine will now stop. IMPORTANT! Running in the engine During the first ten hours of work, run the engine at a moderate RPM and not at full throttle. Allow 10 hours of use to run in the engine. It is at the end of the run-in period that the engine will reach its maximum power. - Page 13 similar. ·Check the fuel filter periodically. Do not allow dust to enter the fuel tank. Clogged filter will cause difficulty when starting engine or abnormalities in engine performance. ·When the filter is dirty, replace the filter. ·When the inside of the fuel tank is dirty, it can be cleaned by rinsing out with petrol.
-
Page 14: Guarantee
proceed as follows: ·Empty the fuel tank completely. ·Protect all metal engine parts from corrosion by coating them with oil. ·Remove the spark plug, put a few drops of oil into the cylinder and then pull the recoil starter 2 to 3 times in order to distribute the fuel evenly. Replace the spark plug. -
Page 15: Ce Declaration Of Conformity
Address: Room 1205,NO.1 ganglong business buliding,NO.99 xiahestreet,economic industrial development,Kunshan city China hereby declare by our own responsibility that the product : GASOLINE BRUSH CUTTER AND GRASS TRIMMER , EKMAN MODEL EKPWT1 Is according to the basic requirements ,which are defined in the European directives : 2006/42/EC(MD),2014/30/EU(EMC) And their amendments. -
Page 16: Exploded View And Parts List
Exploded View and Parts List... - Page 18 Handle Bearing Cable switch Rotation shaft Handle assembly knobs Cutting head Frame Screw Fixed Seat Screw Screws Plastic guard Drive shaft Plastic guard pressing plate Wheel Screw Gasket Blade Tapping screw Terminal pad Line cutting head Pole...