SAFETY NOTICE· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·

SAFETY PRECAUTIONS· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·

TECHNICAL CAUTIONS· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·

SPECIFICATIONS· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·

CIRCUIT PROTECTION· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·

GENERAL INFORMATION· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·

CAUTIONS WHEN CONNECTING/DISCONNECTING THE HV CONNECTOR· · · · · · · · · · · · · · · · · · · · · · · 10

SERVICE ADJUSTMENTS· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·

TROUBLE SHOOTING· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 51

PROTECTION CIRCUIT BLOCK DIAGRAM· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 55

EXPLODED VIEW· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 56

REPLACEMENT PARTS LIST· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 60

BLOCK DIAGRAM· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 96

BASIC CIRCUIT DIAGRAM· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 97

PRINTED CIRCUIT BOARD· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 112

WIRING DIAGRAM· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 120

CAUTION: Before servicing this chassis, it is important that the service technician read the "Safety Precaution"

and "Safety Notice" in this Service Manual.

USE ISOLATION TRANSFORMER WHEN SERVICING

Components having special characteristics are identified by a ! on the schematics and on the parts list in this

service data and its supplements and bulletins. Before servicing the chassis, it is important that the service

technician read and follow the "Safety Precautions" and "Safety Notice" in this Service Manual.

* For continued X-radiation protection, replace picture tube with original type or approved equivalent type.

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

PROJECTION COLOR TELEVISION

SERVICE MANUAL

MODEL: C43-FD2000 C50-FD2000

CONTENTS

SAFETY NOTICE

FH 0202E

Summary of Contents for Hitachi C43-FD2000

Page 1 SERVICE MANUAL DP2M CHASSIS MODEL: C43-FD2000 C50-FD2000 CONTENTS SAFETY NOTICE· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·...
Page 2 C43-FD2000 SPECIFICATIONS Sreen Size : 43 - inch Brightness : 200 cd/m (white screen) Cathode Ray Tube : R P16LXL00 G P16LXL00 Anode Voltage : 30.9kV B P16LXL00 Speakers : Power Supply : 220 - 240V AC, 50/60 Hz Front L/R : 12cm x 2...
Page 3 C50-FD2000 SPECIFICATIONS Sreen Size : 50 - inch Brightness : 200 cd/m (white screen) Cathode Ray Tube : R P16LXL00 G P16LXL00 Anode Voltage : 30.9kV B P16LXL00 Speakers : Power Supply : 220 - 240V AC, 50/60 Hz Front L/R : 12cm x 2 Tweeter: 5cm x 2 Power Consumption : 235W (Operating) Dimension :...
Page 14 GENERAL INFORMATION C43-FD2000 AUTO DIGITAL MAGIC FOCUS CONVERGENCE HEADPHONE JACK S-VIDEO VIDEO SIDE INPUT JACKS ( For INPUT 3) L /(MONO) AUDIO MAGIC FOCUS S-VIDEO VIDEO L /(MONO) AUDIO SIDE CONTROL PANEL (INPUT 3) INPUT SELECTION REMOTE CONTROL SENSOR STANDBY INDICATOR...
Page 15 GENERAL INFORMATION C50-FD2000 AUTO DIGITAL MAGIC FOCUS CONVERGENCE HEADPHONE JACK S-VIDEO VIDEO SIDE INPUT JACKS ( For INPUT 3) L /(MONO) AUDIO MAGIC FOCUS S-VIDEO VIDEO L /(MONO) AUDIO SIDE CONTROL PANEL (INPUT 3) INPUT SELECTION REMOTE CONTROL SENSOR STANDBY INDICATOR VOLUME LEVEL BUTTON CHANNEL SELECTOR ON INDICATOR...
Page 16 P IN P FUNCTIONS The P IN P feature is convenient when you want to watch more than one program at the same time. You can watch a TV program while viewing other programs from the antenna or any of the video inputs. Press the MULTI PIC.
Page 17 P IN P FUNCTIONS NOTE: Some P in P buttons only function in a certain mode. Please refer to the column below. Remote Control Details Buttons MULTI. PIC Switch ON/OFF the P in P sub-window features. P+ / P- Increase/decrease P in P main and sub-picture channel. This button applies only to SPLIT , mode 1 and mode 4 selection.
Page 18 PICTURE & AUDIO SETTINGS PICTURE SETTINGS : The PICTURE menu allows the user to select various controls, such as mode , brightness, color, contrast and tint. To adjust these various controls, follow the guide below. Press the MENU button. MENU PICTURE button to select PICTURE, then Use the...
Page 19 PICTURE & AUDIO SETTINGS NOTE : TINT is only selectable when NTSC is detected. SUPER CONT., NR, VM and CTI are selectable when the Picture mode is in FAVORITE. FILM THEATER is selectable when the Picture mode is in THEATER or FAVORITE. COLOR TEMP.
Page 20 PICTURE & AUDIO SETTINGS FAVORITE : Use this mode for your personal setting preference. THEATER : Use this mode to improve audio performance when watching movies based sources. MUSIC : Use this mode for enhanced high frequency. NARRATION : Use this mode for outstanding vocal clarity. Speaker (Left/Right) Balance Treble Bass...
Page 21 PROTECTION CIRCUIT BLOCK DIAGRAM PROTECTION CIRCUIT BLOCK DIAGRAM Fuse Protector Rectifier AUD+30V T3.15AL:F902 E903 : 5000 29V : D931 AC Cord E901 Protector Rectifier Rectifier SW+11V E904 : 5000 11V: D932 3.3V D901 Switching Fuse Transformer Regulator T4AL : F908 T901 FC 3.3V I907...
Page 45 System Control Circuit Tuner Circuit Description Cir# Pin Voltage (V) Description Cir# Pin Voltage (V) Cir# Voltage(V) Description Cir# Pin Voltage (V) Description Cir# Pin Voltage (V) Cir# Pin Voltage(V) H8S/2238W I001 0.14 H8S/2238W I001 0.00 Q001 5.20 NJW1137M I401 4.50 MSP3455G I101...
Page 46 Video Chroma Circuit Teletext Circuit Headphone Amplifier Circuit Focus Circuit Sensor Distribution Circuit Description Cir# Pin Voltage (V) Description Cir# Pin Voltage (V) Cir# Voltage(V) Description Cir# Pin Voltage (V) Description Cir# Pin Voltage (V) Cir# Pin Voltage(V) Cir# Pin Voltage(V) TB1274AF I501 2.23...
Page 47 AV Switch / Terminal Circuit YC - Separator/ Comb Filter Circuit Description Cir# Pin Voltage (V) Cir# Voltage(V) Description Cir# Pin Voltage (V) Description Cir# Pin Voltage (V) I301 Pin 7 Vpp : 640.0mv 1v/div Cir# Pin Voltage(V) Cir# Pin Voltage(V) I201 Pin 52 Vpp : 720.0mv 1v/div CXA2069Q...
Page 48 Convergence Circuit Deflection Circuit Description Cir# Pin Voltage (V) Cir# Voltage(V) Description Cir# Pin Voltage (V) Cir# Voltage(V) Description Cir# Pin Voltage (V) PDS Pin 13 (BV) I601 Pin 3 Vpp : 56v 200v/div 5ms/div BA17805 IK01 1 7.50 QK01 0.00 LA7845N I601 1...
Page 49 Signal Power Supply Circuit Power Supply Circuit Cir# Voltage(V) Description Cir# Pin Voltage (V) Description Cir# Pin Voltage (V) Cir# Voltage(V) PSD2 Pin 2 Vpp : 13.20v 200v/div 10us/div Q903 19.50 STR-X6468 I901 324.00 STR-F66688 IP01 1.50 QP01 45.60 0.00 0.00 0.00 320.00...
Page 50 Deflection Control Circuit Power Regulator Circuit Signal Processing Circuit Description Cir# Pin Voltage (V) Cir# Pin Voltage(V) Cir# Pin Voltage(V) IC01 Pin 3&8 Vpp : 760.0mv Description Cir# Pin Voltage (V) Description Cir# Pin Voltage (V) Description Cir# Pin Voltage (V) TA1316 IC01 1.40...
Page 51 Trouble Shooting Guide For DP2M Item Changed Adjustment necessary 1 Signal PWB White Balance/ Sub-bright. Tuner (AGC) Horizontal phase / Vertical phase 2 Tuner (Main/ Sub) 3 Micon (I001) No adjustment necessary 4 Feature Box No adjustment necessary 5 Sub Signal PWB Tint adjustment 6 Audio control/ amplifier No adjustment necessary...
Page 52 TROUBLE SHOOTING TROUBLE SHOOTING 1. No Raster and No Power No raster and No sound Check D901, DP01, X901 and others connected F908 blown? to AC main POWER SUP PWB POWER SUP PWB POW/DEF. PWB Any click Over current of VM. S901 turns off sound from Check QE06, QE07, QE56, QE57, QEA6,...
Page 53 DEF-POWER failure: Main-Power check flow Over current in live side. FP01 Check IP01, TP01, CP06, and others connected blown? to IP01(3) POW/DEF. PWB POW./DEF. PWB No Power for IP01. Check IP01, DP07, DP15, DP08, QP01, RP17, RP18 DP09 is lit? and etc.
Page 54 SIG-POWER failure: Sub-Power check flow Over voltage of STBY5V Shutdowned by PROTECTION: While the startup, Check I905 and short-circuit of STBY5V with V>0.5V at I903(1) higher voltage. transiently POWER-SUP PWB POWER-SUP I903(1) 0.8V power on Over current in live side. F902 blown? Check I901, T901 and circuit connected to I901(3) POWER-SUP PWB...
Page 55 Deflection circuit Check flow Check Q933 and Q934. Try to open Raster appear with DP39, DP41, DP34, QP42 and DP46. pin(1) and (2) of PQD2 Check one circuit at one time. shorted? POWER-SUP PWB POW/DEF. PWB Check IC01 pin(26)-Hout, pin(19)-DEF HVcc, Voltage of Q709 (B) I908 and IG04 normal?
Page 59 1. ASSEMBLED P.W.B ADJUSTMENT 1.1 Service menu. Adjustment procedure 1. ‘Off’ the set. Press and hold the ‘TV/VIDEO’ button then ‘on’ the set again until “service menu OSD” appears on the screen. 2. Press ‘MUTE’ button on the R/C to memorize every changes item.
Page 60 ADJ. SPEC = 30.9KV +/-0.2KV (3-1-1) Push " " of remote control and set AGC value (C43-FD2000, C50-FD2000) becomes 180 or greater than 180. (3-1-2) Push the "MUTE" button of remote control, then AGC (2) After the adjustment, fix VR (RH17) with Silicone adjustment is completed.
Page 61 (3-2-2)Then push " " of remote control and set the AGC 2.2 DCU PHASE DATA SETTING value again to greater than and as close as 180. (3-2-3) Push the "MUTE" button of remote control, then AGC adjustment is completed. Adjustment preparation Cut off adjustment should be finished.
Page 62: Lens Focus Adjustment
2.3 RASTER INCLINATION After the adjustment, fix the screw of each DY with a torque of 1.18 Nm(12kgfcm). ADJUSTMENT (DEFLECTION YOKE) 2.4 BEAM ALIGNMENT Adjustment preparation Face the set East or West. Receive the NTSC cross-hatch signal. Preparation for adjustment Contrast should be set MAX.
Page 63 Contrast control should be set Center and (4) In case of G lens. Brightness control should be set minimum. Set to the point where the chromatic aberration switches from blue to red, Adjustment procedure If the chromatic aberration appearing (1) Loosen the fixing screw or wing nut on all over the screen is not the same, the lens cylinder so that the lens observe the vertical bright line and...
Page 64 (NOTE1) (6) In case of B lens. Since the G light is very important for Set the position where the chromatic picture quality and performance. aberration change from purple to Pay special attention in its adjustment. green. As shown below, observe the vertical Note: Be careful not to touch the lens with bright line and adjust lens focus your fingers when adjusting.
Page 65: Static Focus Adjustment
(1) Red static focus adjustment. display the DCU’s cross-hatch pattern. Vary the static focus VR on Focus pack (UFPK) so that the right edge of Hitachi Adjustment procedure mark circle pattern is the best clear. Turn the centering magnets for R, G and B to...
Page 66 2.8 HORIZONTAL SIZE ADJUSTMENT Adjustment Preparation (1) VIDEO control should be set Factory Preset condition. (2) DCU ROM CHECK should be finished. (3) Place the set facing East. Adjustment Procedure PAL 100Hz INTERLACE MODE Item no.14 The 6 (1) Input any PAL signal. lines (2) Press [MENU] key.
Page 67 (6) Press the TV/Video button on the control panel, then SERVICE MENU appears. (7) Choose V.SIZE (item no.13) item by using R/C (b) PAL 50P PROGRESSIVE MODE Item no. 19 up/down cursor key. (8) Adjust V.SIZE (item no.13) as following by using R/C (1) Input any PAL signal.
Page 68 2.11 TRAPEZOID DISTORTION ADJUSTMENT 2.12 BEAM FORM ADJUSTMENT Adjustment Preparation Preparation for adjustment (1) VIDEO control should be set Factory Preset condition. (1) The beam alignment should be completed. (2) HORIZONTAL SIZE adjustment should be finished. (2) The raster inclination, centering, horizontal (3) Place the set facing East.
Page 69 2.13 DIGITAL CONVERGENCE ADJUSTMENT NTSC MODE 50” DIGITAL CONVERGENCE CROSSHATCH 64.5 64.5 13.5 13.5 86.0 86.0 86.0 86.0 86.0 86.0 86.0 86.0 86.0 86.0 1016 UNIT:mm 43” DIGITAL CONVERGENCE CROSSHATCH 55.5 11.5 11.5 55.5 10.7 63.5 63.5 10.7...
Page 70 PAL MODE (50p) 50” DIGITAL CONVERGENCE CROSSHATCH 82.2 82.2 14.8 14.8 82.2 82.2 82.2 82.2 82.2 82.2 82.2 82.2 82.2 82.2 1016 UNIT:mm 43” DIGITAL CONVERGENCE CROSSHATCH 43" 43" 43" 43" 70.7 12.8 70.7 70.7 70.7 70.7 70.7 70.7 70.7 70.7 70.7 70.7...
Page 71 PAL MODE (100i) 50” DIGITAL CONVERGENCE CROSSHATCH 82.2 82.2 14.8 14.8 82.2 82.2 82.2 82.2 82.2 82.2 82.2 82.2 82.2 82.2 1016 UNIT:mm 43” DIGITAL CONVERGENCE CROSSHATCH 43" 43" 43" 43" 12.8 70.7 70.7 70.7 70.7 70.7 70.7 70.7 70.7 70.7 70.7 70.7...
Page 72 BUTTON IDENTIFICATION Digital Convergence Remote Control Model: C43-FD2000 & C50-FD2000 Remote Control Unit CLE-955 PICTURE AUDIO MULTI PIC. RECALL CH I / II TV/VIDEO CROSSHATCH / INITIALIZE VIDEO MODE M. MODE POSITION SWAP REMOVE COLOR MENU RETURN ENTER ADJUSTMENT FREEZE P.
Page 73 (6) Red convergence adj. Receive any NTSC or PAL signal. (RF or VIDEO) Press [0] key on R/C. Just then red Turn on. convergence mode is set. Push the “SERVICE ONLY” switch on the Adjust each red lines to green CONVER/FOCUS P.W.B.
Page 74 MENU] button---- Remove color mode Press [MENU] to switch between all colors displayed or adjustment color and Green Extra only. horizontal line [SUB] button ···Raster position adjustment Adjustment preparation (1) Position adjustment…This will move an entire color. Use this adjustment to match colors at the center of the screen.
Page 75 2.14.2 CONVERGENCE ERRORS If there is an error while performing INITIALIZE or MAGIC FOCUS, error code or message appears on the screen as table below. When MAGIC FOCUS operates: Error code ‘GREEN) appears for about 1 second at bottom right corner, and soon it returns to RF or video signal. When INITIALIZE operates: Error message (RED) appears all the time.
Page 76 2.15 BLUE DEFOCUS ADJUSTMENT Press “MUTE” key on R/C to write the data. REMARKS Preparation for adjustment Observe the TV SET screen directly Optical and electrical focus adjustment by eyes; do not use a mirror. should be completed. The convergence adjustment should be completed.
Page 77 2.17 WHITE BALANCE ADJUSTMENT Adjustment procedure 2.17.1 CHECK CUT OFF ADJUSTMENT A) High Light W/B adjustment: (1) Receive signal for High Light white balance Adjustment preparation ADJ. Pre heat-run should be finished. (2) Adjust the white balance to 14000K +0 MPCD Sub Brightness should be adjusted roughly before (X, Y) = (0.270+/-0.001, 0.280+/-0.001) at the adjust the white balance.
Page 78 WHITE BALANCE ADJUSTMENT FLOWCHART START Cutoff Adj BLUE defocus Adj Sub Brightness Adj (rough) Check Low light W/B If Bluish Adjust High light W/B Repeat two or three times, until no adjustment is needed Adjust Low light W/B Sub bright Adj Check If NOT OK Low light W/B...
Page 79 2.19 TINT ADJUSTMENT 2.18 SUB PICTURE ADJUSTMENT Only applicable for NTSC) Adjustment procedure Preparation pre heatrun should be finished. Input a window pattern signal like below to the (1) Observe P852 on the CPT P.W.B. AV1 and AV2. and change the SUB CONTRAST (Item No.
Page 80 2.20 MAGIC FOCUS OPERATION CHECK Adjustment preparation MAGIC FOCUS INITIALIZE OPERATION should be completed. Receive the RF signal and set to 100Hz mode. MAGIC FOCUS OPERATION Adjustment procedure *GOOD (Several windows) (1) OPERATION CHECK PAL 100i mode: bar. PAL 50p mode: dot. START NTSC 60p mode: space.
Page 81 3. ADJUSTMENT POINT LOCATIONS FRONT 1. CENTERING MAGNET FOR RED PRT 2. CENTERING MAGNET FOR GREEN 3. CENTERING MAGNET FOR BLUE PRT 4. 4-POLE MAGNET FOR BEAM FORM ADJUSTMENT 5. BEAM ALIGNMENT MAGNET 6. FOCUS PACK...
Page 82 POWER SUPPLY PWB S902 S903 T901 I901 S901 L905 L911 D901 L901 L902...
Page 83 SIGNAL P.W.B. I001 SIGNAL P.W.B. I401 SIGNAL SUB P.W.B. IL01 IL02 TERMINAL P.W.B. Rear view...
Page 84 DEFLECTION P.W.B. I601 TP01 (FBT) TH01 RH17 REAR VIEW...
Page 85 CONVER/FOCUS SK01 DIGITAL CONVERGENCE UNIT CONVERGENCE HEAT SINK. REAR VIEW...
Page 86 SIGNAL SUB P.W.B. I301 I303 I3A1 Rear view...
Page 88 C43-FD2000 EXPLODED VIEW NOTE: SOME PARTS MAY APPEAR DIFFERENT THAN THOSE SHOWN IN THE EXPLODED VIEW. WHEN ORDERING, REFER TO THE “REPLACEMENT PART LIST” FOR CORRECT PART NUMBER.
Page 90 Power Supply Convergence Terminal Sensor (Magic Focus) (Input/Output) Control Filter Teletext Note : Below are parts used in C43-FD2000. For parts used in C50-FD2000, please refer to Service Manual Replacement Part List ITEM PART NO DESCRIPTION SYMBOL PART NO DESCRIPTION...
Page 91 C50-FD2000 EXPLODED VIEW...
Page 93 Power Supply Convergence Terminal Sensor (Magic Focus) (Input/Output) Control Filter Teletext Note : Below are parts used in C50-FD2000. For parts used in C43-FD2000, please refer to Service Manual Replacement Part List ITEM PART NO DESCRIPTION SYMBOL PART NO DESCRIPTION...
Page 94 Terminal Sensor (Magic Focus) (Input/Output) Control Filter Teletext Note : Below are parts used in C43-FD2000 and C50-FD2000. For the differences in parts between C50-FD2000 C43-FD2000, please refer to Service Manual Replacement Part List SYMBOL PART NO DESCRIPTION SYMBOL PART NO...
Page 95 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 96 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 97 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 98 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 99 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 100 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 101 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 102 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 103 Terminal Sensor (Magic Focus) (Input/Output) Control Filter Teletext Note : Below are parts used in C43-FD2000 and C50-FD2000. For the differences in parts between C50-FD2000 C43-FD2000, please refer to Service Manual Replacement Part List SYMBOL PART NO DESCRIPTION SYMBOL PART NO...
Page 104 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 105 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 106 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 107 Terminal Sensor (Magic Focus) (Input/Output) Control Filter Teletext Note : Below are parts used in C43-FD2000 and C50-FD2000. For the differences in parts between C50-FD2000 C43-FD2000, please refer to Service Manual Replacement Part List SYMBOL PART NO DESCRIPTION SYMBOL PART NO...
Page 108 Terminal Sensor (Magic Focus) (Input/Output) Control Filter Teletext Note : Below are parts used in C43-FD2000 and C50-FD2000. For the differences in parts between C50-FD2000 C43-FD2000, please refer to Service Manual Replacement Part List SYMBOL PART NO DESCRIPTION SYMBOL PART NO...
Page 109 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 110 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 111 Terminal Sensor (Magic Focus) (Input/Output) Control Filter Teletext Note : Below are parts used in C43-FD2000 and C50-FD2000. For the differences in parts between C50-FD2000 C43-FD2000, please refer to Service Manual Replacement Part List SYMBOL PART NO DESCRIPTION SYMBOL PART NO...
Page 112 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 113 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 114 Terminal Sensor (Magic Focus) (Input/Output) Control Filter Teletext Note : Below are parts used in C43-FD2000 and C50-FD2000. For the differences in parts between C50-FD2000 C43-FD2000, please refer to Service Manual Replacement Part List SYMBOL PART NO DESCRIPTION SYMBOL PART NO...
Page 115 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 116 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 117 Terminal Sensor (Magic Focus) (Input/Output) Control Filter Teletext Note : Below are parts used in C43-FD2000 and C50-FD2000. For the differences in parts between C50-FD2000 C43-FD2000, please refer to Service Manual Replacement Part List SYMBOL PART NO DESCRIPTION SYMBOL PART NO...
Page 118 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 119 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 120 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 121 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 122 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 123 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 124 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 125 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 126 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 127 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 128 PRODUCT SAFETY NOTE : Components marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing. SYMBOL PART NO DESCRIPTION...
Page 129 Dynamic Focus (A2/Nicam/Vol/Sw) Power Supply Convergence Terminal Sensor (Magic Focus) (Input/Output) Control Filter Teletext Note : The asterik (*) indicates difference in parts between C43-FD2000 and C50-FD2000. SYMBOL PART NO DESCRIPTION SYMBOL PART NO DESCRIPTION Comparison Table *RK42 AT03204S METAL OXIDE RES. RSI 1S-3R9JB...
Page 130 Terminal Sensor (Magic Focus) (Input/Output) Control Filter Teletext Note : Below are parts used in C43-FD2000 and C50-FD2000. For the differences in parts between C50-FD2000 C43-FD2000, please refer to Service Manual Replacement Part List SYMBOL PART NO DESCRIPTION SYMBOL PART NO...
Page 131 Power Supply Convergence Terminal Sensor (Magic Focus) (Input/Output) Control Filter Teletext Note : Below are parts used in C43-FD2000 only. For part used in C50-FD2000, please refer to Service Manual Replacement Part List SYMBOL PART NO DESCRIPTION SYMBOL PART NO DESCRIPTION Compound Components REMOTE CON.(NTR1177-010210)

This manual is also suitable for:

C50-fd2000

Hitachi C43-FD2000 Service Manual

Quick Links

Related Manuals for Hitachi C43-FD2000

Summary of Contents for Hitachi C43-FD2000

Page 62: Lens Focus Adjustment

Page 65: Static Focus Adjustment

This manual is also suitable for: