Page 2
In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information and specifications in this document are subject to change without notice.
Mounting, installation and wiring are covered in other documents. Honeywell does not recommend using devices for critical control where there is a single point of failure or where single points of failure result in unsafe conditions. OneWireless is targeted at open loop control, supervisory control, and controls that do not have environmental or safety consequences.
Chassis Ground: Identifies a connection to the chassis or frame of the equipment shall be bonded to Protective Earth at the source of supply in accordance with national and local electrical code requirements. continued OneWireless XYR 6000 HLAI Transmitter R120 User's Manual Revision 9 July 2011...
Page 7
47 of the NZ Trade Marks Act. The mark is only to be used in accordance with conditions laid down by ACMA and RSM. This mark is equal to the CE Mark used in the European Union. N314 directly under the logo is Honeywell’s unique supplier identification number. Revision 9...
Details of topics that relate uniquely to the Honeywell XYR 6000 HLAI Transmitter, This manual does not cover installation, mounting, or wiring. See XYR 6000 Transmitter Quick Start Guide (document 34-XY-25-21). OneWireless network overview OneWireless is an all digital, serial, two-way communication mesh network that interconnects industrial field sensors to a central system.
Bulgaria Lithuania Cyprus Malta Czech Republic Netherlands Denmark Norway Estonia Poland Finland Portugal France Romania Germany Slovakia Greece Slovenia Hungary Spain Iceland Sweden Ireland Switzerland Italy United Kingdom Revision 9 OneWireless XYR 6000 HLAI Transmitter R120 User's Manual July 2011...
Class II and III installations and Type 4X/IP66 applications require that all cable and unused entries be sealed with a NRTL (National Recognized Testing Laboratory) listed cable gland or conduit plug. Cable glands and conduit plugs are not supplied with the product. OneWireless XYR 6000 HLAI Transmitter R120 User's Manual Revision 9 July 2011...
Intentional or unintentional changes or modifications must not be made to the XYR 6000 Wireless Transmitter unless under the express consent of the party responsible for compliance. Any such modifications could void the user’s authority to operate the equipment and will void the manufacturer’s warranty.
100cm from all persons. Furthermore, when using integral antenna(s) the XYR 6000 Wireless Transmitter unit must not be co- located with any other antenna or transmitter device and have a separation distance of at least 20cm from all persons.
525 East Market Street, York, PA 17403 USA Compliance Statement The product herewith complies with the harmonized standards listed above. Typical product line systems and configurations have been tested, for compliance. Revision 9 OneWireless XYR 6000 HLAI Transmitter R120 User's Manual July 2011...
Transmitters is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español Por medio de la presente Honeywell declara que el XYR 6000 (Spanish): Wireless Transmitters cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
ATEX Conditions for Safe Use Because the enclosure of the enclosure of the XYR 6000 Wireless Transmitter is made from aluminum, if it mounted in an area where the use of category 1G apparatus is required, it must be installed such that even in the event of rare incidents, ignition sources due to impact and friction sparks are excluded.
3.1. Installation 3. Preparation Installation Refer to the XYR 6000 Transmitter Quick Start Guide (document 34-XY-25-21) for installation, mounting and wiring of your XYR 6000 transmitter. Configuration The XYR 6000 Transmitter contains the electronics interface compatible for connecting to the OneWireless network.
When ready, in Wireless Builder return the transmitter’s channel to service and set Write Lock to Locked. 0-20 mA 0-20 mA 0-20 mA 0-5V 0-5V 4-20mA 4-20mA 4-20mA 1-5V 1-5V Figure 2 Calibration wiring: voltage (left), current (right) Revision 9 OneWireless XYR 6000 HLAI Transmitter R120 User's Manual July 2011...
5 percent beyond the normal calibration values. Typically this indicates that the applied calibration value was significantly different from the expected value or that the sensor is not within expected tolerances for the applied characterization. OneWireless XYR 6000 HLAI Transmitter R120 User's Manual Revision 9 July 2011...
If the channel is not out of service a WRONG MODE message will be displayed. Go to step 2. Select CAL CLR by scrolling through menu. Press Enter to continue. Display will say BUSY, then SUCCESS. Exit the menu. Revision 9 OneWireless XYR 6000 HLAI Transmitter R120 User's Manual July 2011...
4.1. Introduction 4. Function blocks Introduction This section explains the construction and contents of the XYR 6000 HLAI Transmitter Function Blocks. Block description Block types Blocks are the key elements that make up the transmitter’s configuration. The blocks contain data (block objects and parameters) which define the application, such as the inputs and outputs, signal processing and connections to other applications.
WFN ID by accessing the quick view mode using the Authentication Device navigation keys. For more information on parameters, refer to the following documents. OneWireless Wireless Builder User’s Guide OneWireless Parameter Reference Revision 9 OneWireless XYR 6000 HLAI Transmitter R120 User's Manual July 2011...
Device Local Configuration buttons (Table 10). You can also use the PDA’s buttons. Authentication Device menus are described in section 5.6 starting on page 23. OneWireless XYR 6000 HLAI Transmitter R120 User's Manual Revision 9 July 2011...
Transmitter has connected with only one order to form a redundant connection to the Multinode. network *Use the PDA to determine your radio firmware build number (page 21). Revision 9 OneWireless XYR 6000 HLAI Transmitter R120 User's Manual July 2011...
(4 deg C) Inches of Water at 4 deg C mmHg Millimeters of mercury mmHg (0 deg C) Millimeters of mercury at 0 deg C Milliamperes Volts Percent (default units) OneWireless XYR 6000 HLAI Transmitter R120 User's Manual Revision 9 July 2011...
LOW PWR Low Power External Power Critically Check external 24V power supply LOW BAT Low Battery Battery Voltage Critically Replace batteries as soon as possible. See page 33. Revision 9 OneWireless XYR 6000 HLAI Transmitter R120 User's Manual July 2011...
Page 32
Processor Random Access Memory INP FAIL Input Failure Input Error Check input connection. Check input configuration. Restart the sensor. If condition persists, replace sensor module. See page 30. OneWireless XYR 6000 HLAI Transmitter R120 User's Manual Revision 9 July 2011...
SDREV Sensor device revision SBLD Sensor build number Radio Type DSSS RBLD Radio build number Wireless field network identifier Network device address MODE/CHANNEL Frequency hopping mode & channel Revision 9 OneWireless XYR 6000 HLAI Transmitter R120 User's Manual July 2011...
Secondary receive signal strength. Same as PRI RSSI. Read only. WFN ID Wireless Field Network ID. Read only. DEV ADD Device address. Read only. TX POWER Radio transmit power. Read only. OneWireless XYR 6000 HLAI Transmitter R120 User's Manual Revision 9 July 2011...
Main menu The main menu is shown below. Details start on the next page. Figure 4 Main menu Revision 9 OneWireless XYR 6000 HLAI Transmitter R120 User's Manual July 2011...
PDA, clear the transmitter’s key and reset its configuration to factory default (such as for decommissioning). Figure 5 Security and Device Deployment OneWireless XYR 6000 HLAI Transmitter R120 User's Manual Revision 9 July 2011...
Page 37
For more details on keys, refer to Getting Started with Honeywell OneWireless Solutions. Revision 9 OneWireless XYR 6000 HLAI Transmitter R120 User's Manual...
Go to the upper menu level. When changing a number value, move cursor to the left/more significant digit, then wrap around to the least significant digit. OneWireless XYR 6000 HLAI Transmitter R120 User's Manual Revision 9 July 2011...
Range: 0 to 65535. Build Sensor firmware and radio firmware build numbers. Radio Hardware radio type, FHSS or DSSS WFN ID: Wireless Field Network ID. Range: 0 to 255. Revision 9 OneWireless XYR 6000 HLAI Transmitter R120 User's Manual July 2011...
Page 40
If successful, the device will transition to the connected state. Connected – A secure connection is formed with one or two multinodes. The second line contains detailed state information useful for problem reporting. OneWireless XYR 6000 HLAI Transmitter R120 User's Manual Revision 9 July 2011...
Port infrared communication is not functioning, you can override the detected settings using this option. Read TX Power Level Reads the transmission power level of the transmitter radio. Revision 9 OneWireless XYR 6000 HLAI Transmitter R120 User's Manual July 2011...
6. Maintenance/Repair 6.1. Parts 6. Maintenance/Repair Parts The following replacement parts may be ordered from Honeywell. Part number Qty. Description 50015866-503 ELECTRONICS MODULE ASSEMBLY aka SENSOR MODULE for HLAI 50015866-507 ELECTRONICS MODULE ASSEMBLY aka SENSOR MODULE for HLAI-Instrinsically Safe 50015866-511...
Table 12 Sensor module replacement Step Action Honeywell recommends that the transmitter be removed from service and moved to a clean area before servicing. Loosen the M3 locking set screw on the display end-cap. See item 1 in Figure 9. Unscrew and remove the end cap.
Batteries must not be changed in an explosive gas atmosphere. If IS Battery Pack, Honeywell 50047517-001, has been installed in the Wireless Transmitter, the transmitter enclosure maybe opened when an explosive gas atmosphere is present. Otherwise, do not open transmitter enclosure when and explosive gas atmosphere is present.
0.4 to 0.6 N-M (3.5 – 5.3 Lb-in). Reconnect the Battery Pack connector Honeywell recommends lubricating the end cap with a silicone grease such as Dow Corning #55 or equivalent before replacing the end cap Screw the cap back on and tighten the M3 locking screw...
Disconnect all power from transmitter input sources before accessing the 24V power module. Failure to do so could result in death or serious injury if the input terminals or wires are accidentally touched. Revision 9 OneWireless XYR 6000 HLAI Transmitter R120 User's Manual July 2011...
0,4 – 0,6 N-M (3.5 – 5.3 Lb-in). Re-connect battery connector. Honeywell recommends lubricating the end cap O-ring with a Silicone Grease such as Dow Corning #55 or equivalent before replacing the end cap. Screw the end cap back on and tighten the M3 locking screw.
POTENTIAL ELECTROSTATIC CHARGING HAZARD The integrally mounted antenna shroud is made of Teflon® and has a surface resistance greater than 1Gohm per square. When the XYR 6000 transmitter is installed in potentially hazardous locations care should be taken not to electrostatically charge the surface of the antenna shroud by rubbing the surface with a cloth, or cleaning the surface with a solvent.
See items 2 in Figure 13. Torque screws to 0,4 – 0,6 N-M (3.5 – 5.3 Lb- in). Replace the front end cap. Honeywell recommends lubricating the front end cap O-ring with a Silicone Grease such as Dow Corning #55 or equivalent before replacing the end cap.
6.6. Replacing terminal board Table 16 Terminal board replacement procedure Step Action Honeywell recommends that the transmitter be removed from service and moved to a clean area before servicing. SHOCK HAZARD Depending on your installation, transmitter input wiring sources may contain high voltage.
Page 56
Phone: +(662) 693-3099 China – PRC - Chengdu FAX: +(662) 693-3089 Brazil Honeywell China Inc. Italy MIDDLE EAST Honeywell do Brasil & Cia Honeywell S.p.A. Phone: +(86-28) 8678- Taiwan R.O.C. Abu Dhabi U A E Phone: +(55-11) 7266-1900 Phone:+390292146307 6348 Honeywell Taiwan Ltd.