Signal to noise ratio 45dB Total harmonic distortion Frequency response 20Hz ~ 20KHz(¡ 1dB) Signal to noise ratio Compact Disc 95dB(1kHz 0dB) Channel separation 75dB(1kHz 0dB) Total harmonic distortion 0.05%(1kHz 0dB) * Specifications are subject to change without notice. Samsung Electronics...
3. Disassembly and Reassembly 3-1 Cabinet-Top 1. Remove 11 screws holding the cabinet-top. 2. Lift the back of the cabinet-top and slide it to the rear to remove. (See arrow) Figure 3-1 Samsung Electronics...
Page 4
- Turn the gear clockwise using a screw driver as shown in Figure 3-2- 1. - Pull the Tray in the direction of arrow @ and then remove the Door in the direction of arrow # . 3. Remove 2 screws $ and lift the CD-MECHA. Figure 3-2-1 Figure 3-2 Samsung Electronics...
Page 5
% and then lift the cabinet-rear ^ and slide it to rear to remove (see arrow). 1. Remove 14 screws 2. Remove the Main-PCB & to rear. Figure 3-3 3-4 Cabinet-Front and Cabinet-Bottom 1. Remove 5 screws *. 2. Remove the cabinet-rear by pushing the "A" and "B" as shown. Figure 3-4 Samsung Electronics...
Page 6
Disassembly and Reassembly 3-5 CD Mecha Main Figure 3-5 Samsung Electronics...
Page 7
2. Remove the PCB @ with using the soldering iron. 3. Remove the Hook #. 4. Remove four Shaft-CD$ and then remove four Rubber-CD %. 5. Remove the CD-Deck ^ and Lever-Lift & is removed automatically. 6. Remove the Shaft *. Samsung Electronics...
Page 8
12. Remove the A/S, C/wire 4 with a soldering iron. 13. Remove 1 screw 5 and then remove the connector-header 6, Sensor-Roulette 7 and the A/S, C/wire(FL) 8 with using a soldering iron. 14. Remove the PCB-SUB sensor(R) 9. Figure 3-6 Samsung Electronics...
Page 9
8. Remove the Gear(c) ( by pushing the hook. 9. Lift the Gear(b) ) . 10. Remove the Gear(a) 1 . 11. Remove 2 screws 2 and then remove the Feed-Motor 3 . 12. Remove the Chassis-Deck(M) 4. Figure 3-7 Samsung Electronics...
Figure 4-2 FM Auto Search Level Adjustment 60cm IFT1 AM(MW) I.F Adjustment OUTPUT SSG FREQ. 450KHz AM ANT Adjustment point AM I.F COIL Speaker Terminal AM SSG (IFT1) 450KHZ INPUT Maximum output(Figure 4-3) OUTPUT VTVM Oscilloscope Figure 4-3 AM I.F Adjustment SPEAKER JACK Samsung Electronics...
Page 11
Record Bias oscillation 85KHz 3) Press Hi-SPEED JPT1 MTT5512 frequency button. in the DECK1. 4) Press RECORD button. VTVM Oscilloscope OUTPUT Speaker Frequency (GND) Terminal Counter Figure 4-5 REC PB Head Figure 4-4 AZIMUTH Adjustment Screw Figure 4-6 Samsung Electronics...
Page 12
Raise WVR3 and adjust the waveform so that its middle Set WVR4 to 0mV. comes to GND of the oscilloscope (or until the upper half of waveform becomes symmetrical to the bottom half, A=B) Adjust WVR1 (arrow) for normal sound. Samsung Electronics...
The inverted input of FZC comparator is set to 5.7% of the difference between Vcc and VC(pin69) {{5.7% x (Vcc-Vc)}. Note : If the resistance connected to pin7 changes, the phase compensation peak of the focus tracking sled servos change. (The 'op-amp' dynamic range and offset voltage also change.) Samsung Electronics...
Page 14
TM5 or TM6 = 22µA, This current is inversely proportional to the resistor, variable within a range of t 5 to 40 µA for TM3. STOP is the ON/OFF detection signal for the limit SW (or the sled motor's innermost cirumference). Samsung Electronics...
(pin no. 27 ; 5V) Front PCB When the power is Replace µ-com. ON 'H' displays at pin no. 5 ?(5V) Connect Front PCB and Main PCB. Check the Power PCB : P/T, FUSE Check the connector Main PCB. Wafer MCW2 Samsung Electronics...
Page 16
RC2,3 and RIC1. B+,B- circuits Confirm for TR short AQ103L,R Base B+ ? replace it. Is Mute selected ? Remove it with Remocon. Replace Headphone jack Headphone Jack short ? soldering condition. Check if the output line is short. Samsung Electronics...
Page 17
1.7V 7.5V ? Replace LC72131 AM VT Check the LC72131 LC72131 pin 20 CONTROL ok? 0.9V 7V ? Check HIC1 pin 20 ? Check FEP interior LPF1,2 Check TDA7318 function ok? pattern, and any line output ok? disconnections. Samsung Electronics...
Page 18
Connector inserted Reinsert the connector. correctly? Check Main-PCB Front PCB Check voltage : AC 4.8V connection and the voltage of at FRONT-PCB FLT? MCW2, pins1,2(AC4.8V) Check voltage at UIC1 Check the voltage of RD3(-30V) pin no. 48(-30V) Replace UIC1 Samsung Electronics...
Page 19
2 R/P Deck : L Check for voltage at LC2 BIAS OSC Oscillate RECORD BIAS (85KHZ) Osc Frequency : 85kHz When inoperative : LQ4, LQ3 check Check for voltage at pin no.16,8 R/P Switching Convert of PLAY/RECORD Mode Pin no.16,8 Rec. PLAY Samsung Electronics...
Page 20
Is Roulette Control ok? Check Roulette Control Sensor Check oscillation of XX1 Is Focus Search ok? (16.9344MHz) Does Laser function during Replace PICK UP Focus Search? Check WIC02 pin3 voltage Replace CXD2500Q during Focus Search Replace WIC01 or WIC03 Samsung Electronics...
Page 21
RC2,3 and RIC1. B+,B- circuits Confirm for TR short AQ103L,R Base B+ ? replace it. Is Mute selected ? Remove it with Remocon. Replace Headphone jack Headphone Jack short ? soldering condition. Check if the output line is short. Samsung Electronics...
Page 22
Check communication of MI1 Check connection of short pin3,33,34,42,43 ? Check MI1,CI1 connection Check communication of & short MI1,CI1 ? Check CI1,RI1,RI2,RI3 Check commucation of connection & short CI1,RI1,RI2,RI3 ? Lead In Mode : check data input of CI1 pin104,105,106 Samsung Electronics...
Page 23
Check R.G.B waveform input Check SI1 and short. of EI1 pin12,13,14 ? Check OI2,OI3 and Check clock input of connection condition EI1 pin8 ? Check EI1 pin19 input to Check MI1 pin39 and EQ1. NT : "L", PAL : "H"? Samsung Electronics...
Page 24
Check circuit of OI2,OI3 Does the clock of OI1 pin 4 and connection condition perform input normally? Check circuit of OI1 Does the video waveform output and short of OI1 pin15 ? Check action of OQ1, OQ2, OQ3. 6-10 Samsung Electronics...
Page 25
Check circuit of ALI1, ARI1 Does the audio signal output and short. of ALI1 pin1 , ARI1 pin1 ? Check the mute of Does the audio signal output MIC1 pin18. of ALQ1, ARQ1 collector? Check output wire. Samsung Electronics 6-11...
Page 46
Block Diagrams 9-2 CD Samsung Electronics...
Page 47
Block Diagrams 9-3 Video CD Samsung Electronics...
Page 48
SENS SCOR INTERRUPT REMO REMOCON INPUT DISC2 DISC2 LED DISC3 DISC3 LED VFD CONTROL " " " " " " " " " " " " " +5.6V VDVP -30V VFD PINCH OFF VOLTAGE S 16 VFD CONTROL Samsung Electronics...
Page 49
CLOSE CLOSE SW CE 23 NJU3713(OPTION) CE CE 22 NJU3713 CE DISC1 DISC 1 LED 1 SYNC REC-IN (CD-SYNC) CE 21 M65840 (KEY CON) LATCH DO 2 P5 0 NJU3713, NJU3713 (O) CLK 2 P5 1 NJU3713, NJU3713(O) Samsung Electronics...
Page 50
TUNER TAPE NJU3713 : UIC3 (ECHO, KEY+CON OPTION) Description Name LED : VOICE CANCEL LED : "b" LED : "#" LED : ECHO ON/OFF SW B, C (M62453) SW A (M62453) ECHO CE DATA RESET DOUBLE EMPHA SEL3 Samsung Electronics...