Available languages
Available languages
Quick Links
EN
MultiScanner
800 OneStep
HD
®
Multifunction Wall Scanner
This MultiScanner
800 OneStep
features three scanning modes:
®
HD
®
• StudScan: Locates the center and edges of wood and metal studs up to
3
⁄
in. (19 mm) deep
4
• DeepScan
: Locates the center and edges of wood and metal studs up to
®
1
1
⁄
in. (38 mm) deep
2
• Metal Scan: Detects ferrous (magnetic) metal (such as
1
⁄
inch rebar) up
2
to 3 in. (76 mm) deep and non-ferrous (non-magnetic) metal up to 1
1
(38 mm) deep
1. INSTALLING THE BATTERY
Push in the battery door tab at the bottom of the tool and open
the door. Insert a new 9-volt battery, matching the positive (+)
and negative (-) terminals to the icons printed on the back.
Snap the battery into place and replace the door.
Low Battery Indicator: The Low Battery Indicator icon displays
when the battery level is getting low. While the tool will still operate,
the battery will need to be replaced soon. When the battery icon begins
to flash and is the only icon displayed on the screen, the battery level is too low and not
sufficient to power the tool for proper operation. Please replace the 9-volt battery with
a brand new battery immediately.
2. OPERATING TIPS
For optimum scanning results, it is important to properly hold
the MultiScanner
HD
800 and move slowly when scanning.
®
The following tips will provide more accurate scanning results:
• Grasp the handle with your thumb on one side and your fingers
on the other side. Make sure your fingertips are resting on
the handle and not touching the surface being scanned or the
scanning head of the tool.
• Hold the tool straight up and down, parallel to the studs, and do
not rotate the tool.
• Keep tool flat against the wall and do not rock, tilt, or press hard
when slowly sliding across the surface being scanned.
DO NOT ASSUME THERE ARE NO LIVE ELECTRICAL WIRES IN THE
WARNING
WALL. DO NOT TAKE ACTIONS THAT COULD BE DANGEROUS
IF THE WALL CONTAINS A LIVE ELECTRICAL WIRE. ALWAYS TURN OFF THE
ELECTRICAL POWER, GAS, AND WATER SUPPLIES BEFORE PENETRATING A
SURFACE. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN ELECTRIC
SHOCK, FIRE, AND/OR SERIOUS INJURY OR PROPERTY DAMAGE.
Always turn off power when working near electrical wires.
7. SCANNING IN METAL MODE
Note: When scanning for studs, use StudScan mode (or DeepScan
®
mode on thicker
walls) to quickly locate the center and edges. Use Metal Scan to determine if the
previous reading in StudScan was a wood stud, metal stud, or pipe. In Metal Scan,
only metal drywall screws will be found in wood studs, while metal will be indicated
everywhere on a metal stud or pipe.
Metal Scan has interactive calibration to adjust to its sensitivity to metal, which can
be used to find the precise location of metal objects in walls, floors, and ceilings.
Maximum sensitivity is ideal for quickly finding the approximate location
of metal. However, sensitivity can be reduced by calibrating the tool closer to metal.
With reduced sensitivity, the area where metal is indicated will be smaller. But in
both cases, the metal target is in the center of the area where the tool indicates metal
is present.
1. Move mode switch to Metal Scan mode. For maximum metal sensitivity, turn the
tool on in the air by pressing and holding the Power button. This will ensure that it
calibrates away from any metal objects. (The tool can only be calibrated
off the wall in Metal Scan mode.)
2. (Figure A) While holding the Power button, press the tool flat against the wall
and slowly slide the scanner across the surface. Mark the point where you get the
highest metal indication (the most Middle bars on the screen). If it is a strong target,
the SpotLite
Pointer will also shine a beam of light and a steady beep will sound.
®
Continue in the same direction until display bars reduce. Reverse direction and mark
the spot where the display bars peak from the reversed direction. The midpoint of the
two marks is the location of the center of the metal object.
If the unit indicates metal over a large area, you can refine the scanning area to
more accurately locate the metal target by following steps 3 and 4 below.
3. (Figure B) To further pinpoint the location of the metal target, scan the area again.
Release the Power button and then turn the unit back on, this time starting on the
wall over one of the previous marks. This will reset the tool to a lower sensitivity and
narrow the scan area.
4. (Figure C) To continue to reduce sensitivity and further refine the scanning area,
repeat step 3. This procedure can be repeated multiple times to narrow the field
even further.
®
SpotLite
Pointer
®
Target Spotlight
Backlit LCD Display
Target Indication Bars
Auto Correcting
Indication
Signal Strength
Indicator
⁄
in.
2
WireWarning
Detection
Indicator
Edge / Center
Indicator
Low Battery
Indicator
Metal Mode
Indicator
StudScan /
DeepScan
®
Mode Indicator
Mode
Power Button
Selector
Switch
Battery (Door Tab)
Note: If any bars display on the screen, metal is present. Small targets or targets deep
within the surface may only illuminate some of the bars and not the center line or audio
tone. In this case, use the highest indication to determine the metal position.
Figure A
FCC Part 15 Class B Registration Warning
This device complies with Part 15 of FCC Rules. Operations subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Figure B
Figure C
• Avoid placing your other hand, or any other part of your
bars when the tool locates a stud through thick surfaces.
body, on the surface being scanned. This will interfere with
MultiScanner
the tool's performance.
and padding. In problematic situations, try using Metal Scan to locate nails or screws
• If you're receiving erratic scanning results, it may be a result
that may line up vertically where a stud or joist is positioned.
of humidity, moisture within the wall cavity or drywall,
Note: Sensing depth and accuracy can vary due to moisture, content of materials, wall
or recently applied paint or wallpaper that hasn't fully dried.
texture, and paint.
While the moisture may not always be visible, it will interfere
WARNING
with the tool's sensors. Please allow a few days for the wall
to dry out.
locate items before penetrating the surface. Such additional sources include
• Depending on the proximity of electrical wiring or pipes to
construction plans, visible points of entry of pipes and wiring into walls,
the wall surface, the scanner may detect them in the same
such as in a basement, and in standard 16 and 24 in. (41 and 61 cm) stud
manner as studs. Caution should always be used when nailing,
spacing practices.
cutting, or drilling in walls, floors, and ceilings that may contain
these items.
3. SELECTING THE MODE
®
• To avoid surprises, remember that studs or joists are normally
Move selector switch to the desired mode: StudScan for finding wood or metal
spaced 16 or 24 in. (41 or 61 cm) apart and are 1
1
⁄
in. (38 mm)
2
studs; DeepScan
in width. Anything closer together or a different width
locating metal.
may not be a stud, joist, or firebreak.
Unit will remain off if Power button is not pressed.
Always turn off power when working near electrical wires.
4. TURNING ON/CALIBRATING THE TOOL
SCANNING DIFFERENT SURFACES
Wallpaper: MultiScanner
800 functions normally on walls
®
HD
MultiScanner
covered with wallpaper or fabric, unless the materials are
the subsurface environment 10 times per second and automatically recalibrates, when
metallic foil, contain metallic fibers, or are still wet after
needed, to successfully find the center of studs in one step.
application. Wallpaper may need to dry for several weeks
• Place MultiScanner
after application.
StudScan or DeepScan
Freshly painted walls: May take one week or longer to dry
• Once powered on, tool will automatically perform all calibrations. The LCD will
after application.
display all icons until calibration is complete. Upon completion of calibration, the
Lath & plaster: Due to irregularities in plaster thickness, it
SpotLite
is difficult for MultiScanner
800 to locate studs in Stud
®
HD
continuous measurements. Continue to press Power button down and keep the tool
modes. Change to Metal Scan mode to locate the nail heads
flat against the wall and begin scanning.
holding wood lath to the studs. If the plaster has metal mesh
Note: It is important to wait for calibration to complete (1–2 seconds) before moving
reinforcement, MultiScanner
HD
800 may be unable to detect
®
the scanner.
through that material.
ACT
™
(Auto Correcting Technology)
Extremely textured walls or acoustic ceilings:
During scanning, the tool will
When scanning a ceiling or wall with an uneven surface, place
automatically recalibrate itself
thin cardboard on the surface to be scanned and scan over the
when needed. This recalibration is
cardboard in DeepScan
mode. If irregular scanning results are
®
transparent and no indication is made.
received, switch to Metal Scan mode to locate nails or drywall
If an arrow icon illuminates, the tool
screws that line up vertically where a stud or joist is positioned.
calibrated near or over a stud and then
Wood flooring, subflooring, or gypsum drywall over
moved away. The arrow indicates the
plywood sheathing: Use DeepScan
®
mode and move the tool
direction of the missed stud.
slowly. The Signal Strength Indicator may only display 1 or 2
8. HELPFUL HINTS
Detects other objects besides studs
in StudScan mode.
Finds more targets than there
should be.
Difficulty detecting metal.
Image of metal object appears wider
than actual size.
Constant readings of studs near
windows and doors.
You suspect electrical wires, but do not
detect any.
Flashing Low Battery Indicator and tool
not operating.
ACT, DeepScan, MultiScanner, OneStep, SpotLite, WireWarning, and Zircon are registered trademarks or trademarks of Zircon Corporation.
Visit www.zircon.com/support for the most current instructions.
LIMITED 1 YEAR WARRANTY
Zircon Corporation, ("Zircon") warrants this product to be free from defects in materials and workmanship
for one years from the date of purchase. Any in-warranty defective product returned to Zircon*, freight prepaid
with proof of purchase date and $5.00 to cover postage and handling, will be repaired or replaced at Zircon's
option. This warranty is limited to the electronic circuitry and original case of the product and specifically
excludes damage caused by abuse, unreasonable use or neglect. This warranty is in lieu of all other warranties,
express or implied, and no other representations or claims of any nature shall bind or obligate Zircon.
Any implied warranties applicable to this product are limited to the one year period following its purchase.
IN NO EVENT WILL ZIRCON BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM POSSESSION, USE OR MALFUNCTION OF THIS PRODUCT.
In accordance with government regulations, you are advised that: (i) some states do not allow limitations on
how long an implied warranty lasts and/or the exclusion or limitation of incidental or consequential damages,
so the above limitations and/or exclusions may not apply to you, and further (ii) this warranty gives you specific
legal rights and you may also have other rights which vary from state to state.
5. FINDING A STUD
HD
800 cannot scan for wood studs and joists through concrete or carpet
®
Always scan for studs with the scanner placed flat against the wall.
Move the mode switch to StudScan, place the tool flat against the wall,
then press and hold the Power button. Wait for beep to confirm
calibration has completed before moving scanner.
Do not rely exclusively on the detector to locate items behind
the scanned surface. Use other information sources to help
Slowly slide tool across surface. EDGE indication
will illuminate, indicating location of the stud edge.
Continue sliding tool. When the center of a stud
®
for scanning walls over
3
⁄
in. (19 mm) thick; or Metal Scan for
4
is located, the three bars on the Signal Strength Indicator,
the middle segments of the Target Indication bars,
CENTER indication, and SpotLite
illuminate and the buzzer will sound.
HD
800 can be calibrated anywhere on the wall. It provisionally monitors
®
®
HD
800 against the wall before pressing the Power button in
®
mode.
In cases of deeper studs (thicker walls), when the
center of the stud is located only two bars will show
on the Signal Strength Indicator and only the SpotLite
Pointer and buzzer will momentarily activate and the tool will begin
Pointer and middle segments of the Target Indication
®
Bars will illuminate. If you still cannot locate a stud,
try DeepScan
6. WIREWARNING
Zircon's WireWarning
and Metal Scan modes. When live AC voltage is detected, the WireWarning
indicator will appear in the display. If scanning begins over a live AC wire, the AC
indicator will flash continuously. Use extreme caution under these circumstances or
whenever live AC wiring is present.
concrete, encased in conduit, present behind a plywood shear wall or metallic
wall covering, or if moisture is present in the environment or scanned surface.
(See also number 2, Operating Tips)
Situation
Probable Cause
• Electrical wiring and metal/plastic pipes may be
• Scan the area in Metal Scan to determine if metal is present.
near or touching back surface of wall.
• Check for other studs equally spaced to either side 12, 16, or 24 in. (31, 41, or 61 cm) apart or for the same stud
at several places directly above or below the first scan area.
• A stud reading would measure approximately 1
most likely not a stud if not near a door or window.
• Tool calibrated over metal object.
• The scanner may have been calibrated over a metal object, reducing sensitivity. Try calibrating in another location.
• Metal targets too deep or small.
• Scan in both horizontal and vertical directions. Metal sensitivity is increased when metal object is parallel to sensor,
located under Zircon logo.
• Metal has greater density than wood.
• To reduce sensitivity, recalibrate MultiScanner
• Double and triple studs are usually found around
• Detect outer edges so you know where to begin.
doors and windows. Solid headers are above them.
• Wires are shielded by metal conduit, a braided
• Try Metal Scan mode to see if you can find metal, wire, or metal conduit.
wire layer, metallic wall covering, plywood shear
• Use extra caution if the area has plywood, thick wood backing behind drywall, or thicker than normal walls.
wall, or other dense material.
• If a switch controls an outlet, make sure it is ON for detection, but turned off when working near
• Wires deeper than 2 in. (51 mm) from surface
electrical wires.
might not be detected.
Use CAUTION when nailing, sawing, or drilling into walls, floors, and ceilings where these items may exist.
• Wires may not be live.
• Battery level too low for proper operation.
• Replace with brand new alkaline 9 V battery.
Return product freight prepaid with proof of purchase date (dated sales receipt) and $5.00 to cover postage
and handling, to:
Zircon Corporation
*Attn: Returns Department
1580 Dell Avenue
Campbell, CA 95008-6918 USA
Be sure to include your name and return address. Out of warranty service and repair, where proof of purchase
is not provided, shall be returned with repairs charged C.O.D. Allow 4 to 6 weeks for delivery.
Customer Service, 1-800-245-9265 or 1-408-963-4550
Monday–Friday, 8:00 a.m. to 5:00 p.m. PDT
www.zircon.com • [email protected]
©2014 Zircon Corporation • P/N 66212 • Rev C 09/14
Pointer will all
®
®
mode.
®
DETECTION
®
detection feature works continuously in StudScan, DeepScan
,
®
®
®
detection
Electrical field locators may not detect live AC wires if wires
WARNING
are more than 2 in. (51 mm) from the scanned surface, in
Solution
⁄
in. (38 mm) apart from each edge; anything larger or smaller is
1
2
800 over either of first two marks (Metal mode only).
®
HD
ZirconCorporation
ZirconTV
|
ZirconTools
ZirconToolPro
ZirconTools
Related Manuals for Zircon MultiScanner HD800 OneStep
Summary of Contents for Zircon MultiScanner HD800 OneStep
- Page 1 Zircon Corporation more accurately locate the metal target by following steps 3 and 4 below. with proof of purchase date and $5.00 to cover postage and handling, will be repaired or replaced at Zircon’s *Attn: Returns Department 3. (Figure B) To further pinpoint the location of the metal target, scan the area again.
- Page 2 3 y 4 que se indican a Zircon*, con flete prepago con comprobante de la fecha de compra y $5.00 para cubrir el envío, será reparado y *Attn: Returns Department (Departamento de Devoluciones) a continuación.