Use of controls or adjustments or performance of proce- 2967-3, ISHIKAWA-CHO, u163 HACHIOJI-SHI, TOKYO, JAPAN dures other than those specified herein may result in KENWOOD CORP. CERTIFIES THIS hazardous radiation exposure. EQUIPMENT CONFORMS TO DHHS REGULATIONS NO. 21 CFR 1040.10, In compliance with Federal Regulations, following are re- CHAPTER 1, SUBCHAPTER J.
Page 4
DM-VH7 3 7 63 1515 0 CIRCUIT DESCRIPTION 2-2 Pin description Pin No. Name Description VOL_DT Electric VOL IC • communication data VOL_CK Electric VOL IC • communication clock Not used DISP_CE Display ucom • communication CE DISP_OUT Display ucom • communication data output DISP_IN Display ucom •...
Page 6
DM-VH7 3 7 63 1515 0 CIRCUIT DESCRIPTION 3-2 Pin description Pin No. Name Description E2PROM clock E2PROM data 3~11 Not used VDD/power supply Not used 15~30 Not used SRVMOD X-Y position output 32~34 Not used MUTE_BAR Mute L:MUTE ON...
Page 7
DM-VH7 CIRCUIT DESCRIPTION 3 7 63 1515 0 Pin No. Name Description MNT1 ACRIC/ATRAC en/decoder IC shock (track jump) detection XINT ATRAC thrust 93~95 Not used ACRIC/ATRAC en/decoder IC TX (Recording data output enable) RECP ACRIC/ATRAC en/decoder IC RECP (Laser power changeover)
Page 8
DM-VH7 CIRCUIT DESCRIPTION 3 7 63 1515 0 5. TEST MODE For more information on each adjustment mode, refer to each section of 6, "Electrical adjustment". 5-1 How to Setting and Cancel Test Mode If other adjustment mode has been entered incorrectly, Setting: While pressing the ON/STANDBY and MODE press the STOP key to exit the mode.
Page 9
DM-VH7 CIRCUIT DESCRIPTION 3 7 63 1515 0 6. Electrical adjustment 6-5 Offset Adjustmen 6-1 Precaution during confirmation of Laser Diode N o . K e y D i s p l a y / F u n c t i o n...
Page 10
DM-VH7 CIRCUIT DESCRIPTION 3 7 63 1515 0 6-7 Traverse Adjustment 6-8 Focus Bias Adjustment Connection : Use the special disc(continuous recorded disc) Oscilloscope N o . K e y D i s p l a y / F u n c t i o n...
DM-VH7 3 7 63 1515 0 MECHANISM DESCRIPTION 1. Eject Operation 1. The gear(worm) turns clockwise(1) if the start limit switch is in off. (the pickup Gear(Feed) is not full inward position) 2. The gear(feed) turns frontwards.(2) 3. The pickup travels inwards by the reed-screw.(3) Gear(Worm) 4.
Page 12
DM-VH7 3 7 63 1515 0 MECHANISM DESCRIPTION FRONT Slider (outer) Lever (change) Slider (inner) 12. The lever(change) moves and turns clockwise(0) after the slider(outer) travels to the stop position. 13. The gear(final) separates from the slider(outer). And the gear(final) engages with the slider(inner).
Page 13
DM-VH7 3 7 63 1515 0 MECHANISM DESCRIPTION HOLDER ASS'Y FRONT 2. Loading Operation 1. The disc is loaded. 2. The slider(inner) is pressed. 3. The eject detection switch turns off. 4. The loading motor turns counterclockwise. L 13942296513 5. The disc is inserted into the mechanism in the reverse order of eject operation.
Page 21
Desti- Desti- Ref. No Parts No. Description Ref. No Parts No. Description ress Parts nation marks Parts nation marks ress DM-VH7 J19-5994-04 HOLDER J19-5995-14 HOLDER A01-3696-01 METALLIC CABINET(TOP) J19-5996-02 BRACKET A01-3698-01 METALLIC CABINET(BOTTOM) J42-0083-05 POWER CORD BUSHING A09-1106-08 CABINET J61-0098-05...
Page 22
3 7 6 3 1 5 1 5 0 New Parts New Parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 23
3 7 6 3 1 5 1 5 0 New Parts New Parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 24
3 7 6 3 1 5 1 5 0 New Parts New Parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
Page 25
3 7 6 3 1 5 1 5 0 New Parts New Parts Parts without Parts No. are not supplied. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No.
H : 237 mm (9 - 5 / 16") D : 279 mm (11") Weight (Net) ................3.1 kg (6.8 lb) 1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice. Notes Notes 2.