Related Manuals for ABB M2131xPx-A series
Summary of Contents for ABB M2131xPx-A series
- Page 1 VER:1.3 │ 20.06.2017 Operating Instructions ABB-Welcome Mini video outdoor station M2131xPx-A M2136xPx-A...
-
Page 2: Table Of Contents
Table of contents Table of contents Safety .................................... 3 Intended use ................................. 3 Environment .................................. 3 ABB devices ..............................3 Front overview ..............................4 Terminal description ............................5 Lock type and connection ..........................7 Technical data ................................8 Mounting/Installation ..............................9 Requirement for the electrician ........................ -
Page 3: Safety
ABB devices All packaging materials and devices from ABB bear the markings and test seals for proper disposal. Always dispose of the packing materials and electric devices and their components via an authorized collection facility or disposal company. -
Page 4: Front Overview
Environment Front overview Fig. 1 Function Light sensor Infrared LED Indicator LED (ring, call and door open) Speaker and microphone integration Pushbutton Nameplate Tab.1 │4 Operating Instructions VER:1.3... -
Page 5: Terminal Description
Environment Terminal description Fig. 2 Function Connector for device software update Rotary switch to set the address of outdoor station (1-9) Set feedback tone of pushbutton ON/OFF Set general call to all indoor stations in one family: ON/OFF If GC=ON, press button 1/button 2, all IS ring Configuration function of 1st/2nd round pushbutton 5A mini video outdoor station with one pushbutton 3 ->... - Page 6 Environment Set the video mode PAL/NTSC OFF = PAL video mode ON = NTSC video mode Set default lock OFF = set (Lock-GND) as default lock ON = set (COM-NC-NO) as default lock *Default lock is controlled by "unlock" button on IS Plug-in clamps (a,b) for bus connection Plug-in clamps (Exit-GND) for exit button Plug-in clamps (Lock-GND) for door opener...
-
Page 7: Lock Type And Connection
Environment Lock type and connection Lock type Operation type Voltage Wiring type Type A Electrical strike lock, Power on to open 12 VDC/AC 12 V Type B Electrical strike lock, Power on to open 24 VDC/AC Type B 24 V Type A Electrical rim lock, 12 V Power on to open... -
Page 8: Technical Data
Technical data Technical data Designation Value Operating temperature -40 °C - +70 °C Protection IP 54 Power supply, door opener (Lock-GND) 18 V 4 A impulsive, 250 mA holding Floating supply, door opener (COM-NC-NO) 30 V DC/AC 1A Single-wire clamps 2 x 0.28 mm - 2 x 0.75 mm Fine-wire clamps... -
Page 9: Mounting/Installation
Mounting/Installation Mounting/Installation Warning Electric voltage! Dangerous currents flow through the body when coming into direct or indirect contact with live components. This can result in electric shock, burns or even death. – Disconnect the mains power supply prior to installation and/or disassembly! –... -
Page 10: Mounting
Mounting/Installation Mounting 5.2.1 Preparation Use gloves to protect yourself from being cut. Fig. 4 5.2.2 Surface mounting 78 mm 99 mm 26.5 mm ① ② Fig. 5 │10 Operating Instructions VER:1.3... -
Page 11: Flush Mounting
Mounting/Installation 5.2.3 Flush mounting Product dimension 90 mm 105 mm 43 mm Front view Back view Side view Fig. 6 Mounting without pre-installation box 90 mm 33 mm 10 mm Fig. 7 │11 Operating Instructions VER:1.3... - Page 12 Mounting/Installation Mounting with pre-installation box 99 mm 45 mm 99 mm Fig. 8 Precautions for installation When opening a square groove for the lower cover of the equipment, you must control the embedded depth, ensuring the outer edge of the lower cover can be fully attached to the wall, but should not leave a large gap between the exposed parts of the face shell and the wall after the installation of the equipment;...
-
Page 13: Cavity Wall Installation
Mounting/Installation 5.2.4 Cavity wall installation Product dimension 90 mm 105 mm 43 mm Front view Back view Side view Fig. 9 Installation dimension 92 mm <29 mm 97 mm 7 mm Fig. 10 │13 Operating Instructions VER:1.3... - Page 14 Mounting/Installation Cavity wall installation Fig. 11 │14 Operating Instructions VER:1.3...
-
Page 15: Dismantling
Mounting/Installation 5.2.5 Dismantling Fig. 12 5.2.6 Replace the nameplate TT L/N TT L/N Fig. 13 │15 Operating Instructions VER:1.3... -
Page 16: Installation Situations
Mounting/Installation 5.2.7 Installation situations Note The following installation situations must be avoided without fail to ensure picture quality. – Direct light – Direct sunlight – Extremely bright picture background – Highly reflective walls on the opposite side of the door station –... -
Page 17: Commissioning
Commissioning Commissioning Configure functions of the 1st/2nd pushbutton Fig. 14 Function 3-> OFF, 4-> OFF Call apartment 001 Call apartment 002 Tab.5 Fig. 15: Function 3-> OFF, 4-> ON Call guard unit Call apartment 001 Tab.6 │17 Operating Instructions VER:1.3... - Page 18 Commissioning Fig. 16 Function 3-> ON, 4-> OFF Switch on light Call apartment 001 Tab.7 Fig. 17 Function 3-> ON, 4-> ON Call apartment 001 Call apartment 002 Tab.8 │18 Operating Instructions VER:1.3...
-
Page 19: Setting General Call Function
Commissioning Setting general call function Fig. 18 Function 2-> OFF Call apartment 001, both 001 indoor stations ring Call apartment 002, both 002 indoor stations ring Tab.9 Fig. 19 Function 2-> ON Call apartment 001, all 4 indoor stations (different address) ring Call apartment 002, all 4 indoor stations (different address) ring Tab.10 * If the "call forward function"... -
Page 20: Operation
Operation Operation Manage ID cards by mini outdoor station Programming Function Command Indicated color of door open Create admin card Swipe card 1x Green Enter settings Swipe admin card 1x Orange Tab.11 The system will take the first card swiped after powering up the system within 60s to be the admin card. - Page 21 Operation Open a door Function Command Indicated color of door open Open a door Swipe the enrolled keycard Green Tab.14 Reset to factory default Function Command Indicated color of door open 3 LED: green cycle flash Press and hold the 1st button for 3 s to enter configuration mode.
-
Page 22: Notice
We reserve the right to at all times make technical changes as well as changes to the contents of this document without prior notice. The detailed specifications agreed to at the time of ordering apply to all orders. ABB accepts no responsibility for possible errors or incompleteness in this document. - Page 23 ABB (United Arab Emirates) ABB (Vietnam) Ltd. The detailed specifications agreed Industries(L.L.C) Km 9 National Highway 1A , upon apply for orders. ABB accepts P.O.Box 11070 Dubai-UAE Hoang Liet, Hoang Mai, Hanoi, no responsibility for possible errors T : +971 4 3147 586 Vietnam or incompleteness in this document.