Table of Contents
Quick Links
OPERATING INSTRUCTIONS
Version 01/07
FAZ3000-FB-2
Wireless remote control
Item no. 75 08 43
This user manual belongs to this product. It contains important
information specific to its operation and handling. Please bear this in
mind when passing on the product to a third party.
Therefore keep this user manual for future reference!
A contents list can be found in the table of contents on page 3.
Table of Contents
Related Manuals for Conrad Electronic FAZ3000-FB-2
Summary of Contents for Conrad Electronic FAZ3000-FB-2
- Page 1 OPERATING INSTRUCTIONS Version 01/07 FAZ3000-FB-2 Wireless remote control Item no. 75 08 43 This user manual belongs to this product. It contains important information specific to its operation and handling. Please bear this in mind when passing on the product to a third party.
-
Page 2: Faz3000-Fb
Introduction Dear customer, Thank you for purchasing this product. This product meets the requirements of both current national and European guidelines. In order to ensure continued fulfilment of legal requirements and safe operation of this product, we kindly ask you to carefully follow the instructions in this user manual! Please read the user manual completely and observe the safety and operation instructions before using the product! -
Page 3: Table Of Contents
Table of contents Page 1. Prescribed use ..................4 2. Scope of delivery ................. 4 3. Explanation of icons ................4 4. Safety instructions ................5 a) General information ................ 5 b) Handling the batteries ..............6 5. General information ................7 6. -
Page 4: Prescribed Use
1. Prescribed use The ‘FAZ3000-FB-2’ wireless remote control is a part of the ‘FAZ3000’ wireless alarm system. The ‘FAZ3000-FB-2’ wireless remote control is used to activate/deactivate the ‘FAZ-Z’ alarm base station (toggle between ‘disarmed’, ‘internally armed’ and ‘externally armed’). It also has a panic function that can trigger an alarm using the ‘FAZ-Z’ alarm base station. -
Page 5: Safety Instructions
4. Safety instructions The product’s guarantee becomes invalid, if the product is damaged as a result of the failure to observe these operating instructions! We do not assume any liability for any resulting damages! We do not assume liability for damage to property or personal injury caused by improper use or failure to observe the safety instructions. -
Page 6: B) Handling The Batteries
b) Handling the batteries • Keep batteries out of the reach of children. • Make sure that the polarity is correct when inserting the batteries. • Do not leave batteries lying around as they could be swallowed by children or pets. In such case seek immediate medical care. •... -
Page 7: General Information
5. General information The ‘FAZ3000-FB-2’ wireless remote control is part of the ‘FAZ3000’ wireless alarm system, and is used to activate/deactivate the ‘FAZ-Z’ alarm base station. The ‘FAZ3000-FB-2’ wireless remote control can be used to toggle the ‘FAZ-Z’ alarm base station between three modes, namely ‘disarmed’, ‘internally armed’... -
Page 8: Controls
6. Controls ‘ext.’ button (= ‘externally armed’) ‘int.’ button (= ‘internally armed‘) ext. int. ‘unscharf’ button (= ‘disarmed’) Opening to attach to a key ring unscharf The cover of the battery compartment is located at the rear side of the remote control. -
Page 9: B) Special Function 'Attack Alarm
Please note: An attack alarm is not triggered when all three buttons of the ‘FAZ3000-FB-2’ remote control are pressed simultaneously. Likewise, simultaneously pressing the two ‘ext.’ and ‘int.’ buttons does not set off an attack alarm. You can stop the alarm in the usual way; simply press the ‘unscharf’ (disarm) -
Page 10: Inserting The Batteries, Entering The Security Code
‘FAZ-Z’ alarm base station later. If the ‘FAZ-Z’ alarm base station detects the radio signal of the ‘FAZ3000-FB-2’ remote control, the alarm base station responds only if the received security code matches the stored security code. Proceed as follows: 1. - Page 11 as described below (‘Re-entering or changing the security code’) if you wish to enter a new security code. 6. At the time of the initial operation, the LED ( ) on the front side blinks for approximately 20 seconds; this indicates that it is ready to accept the security code input.
-
Page 12: Registering The Remote Control To The 'Faz-Z' Alarm Base Station
‘FAZ-Z’ alarm base station The remote control must be registered to the alarm base station to ensure that the ‘FAZ-Z’ alarm base station responds to the ‘FAZ3000-FB-2’ remote control. The alarm base station stores the security code of the remote control. - Page 13 • Briefly press any button on the remote control. rem.con. 1 The alarm base station acknowledges reception by emitting a short signal tone and the LCD on the alarm base station switches to the display for entering the name of the remote control. •...
-
Page 14: Deleting A Remote Control From The 'Faz-Z' Alarm Bas Station
9. Deleting a remote control from the ‘FAZ-Z’ alarm base station If a remote control is lost or stolen, it must be deleted immediately from the ‘FAZ-Z’ alarm base station. Burglary protection cannot be then guaranteed since a finder or a thief can ‘disarm’... - Page 15 • Press the ‘ ’ button to access the menu for rem.con. 1 remote controls. Peter • You can use the ‘ ’ and ‘ ’ buttons to select the rem.con. 2 remote controls that you wish to delete (the Dana second remote control used by ‘Dana’...
-
Page 16: Information On The Range
10. Information on the range Ranges and interference • The components of the ‘FAZ3000’ wireless alarm system work in the 868MHz range, which is also used by other radio services. Therefore devices that operate on the same or neighbouring frequencies may restrict both its operation and its range. -
Page 17: Handling
11. Handling • Protect the product against humidity, cold, heat, dust, and direct sunlight. • The cold (for instance, when the remote control lies in a vehicle in winter) has negative effects on the battery life; it may decrease the range as well. •... -
Page 18: Maintenance And Cleaning
12. Maintenance and cleaning • The remote control does not require servicing except for replacing the batteries when needed. • Never dismantle the product. Have the device repaired by a skilled technician only, otherwise the device’s licence and its guarantee will become invalid. -
Page 19: Disposal
13. Disposal a) General information When the product is no longer usable, dispose of it in accordance with the applicable statutory regulations. b) Battery/rechargeable battery disposal As the consumer, you are legally obliged to return all your used batteries and rechargeable batteries. -
Page 20: Technical Specifications
14. Technical specifications • Range ......... up to 100m (*) • Radio frequency: ....... 868.35MHz • Power supply: ......1 x CR2016 • Dimensions: ....... 40mm x 52mm x 11mm (W x H x D) • Number of security codes: ..3 = 19683 •... -
Page 21: Brief Instructions
15. Brief instructions a) Registering the remote control in the alarm base station • Set the alarm base station in the search mode of the remote control • Insert the batteries in the remote control • In case of the initial operation, enter the 9-digit security code or re-program it (note down and store the security code safely in both cases, see pages 5, 10 and 11). -
Page 22: Declaration Of Conformity (Doc)
16. Declaration of conformity (DOC) We, Conrad Electronic, Klaus-Conrad-Straße 1, 92240 Hirschau (Germany), hereby declare that this product complies with the fundamental requirements and other relevant regulations of directive 1999/5/EC. You can find the declaration of conformity for this product at... - Page 24 100% recycled The operating instructions reflect the current technical specifications at paper. the time of print. We reserve the right to change the technical or physical specifications. Bleached without © Copyright 2007 by Conrad Electronic SE. Printed in Germany. chlorine.