Ec Declaration Of Conformity; Additional Safety Rules - Makita GA7030 Instruction Manual
Hide thumbs
Also See for GA7030:
- Instruction manual (148 pages) ,
- Quick start manual (2 pages) ,
- Specifications (2 pages)
Table of Contents
Available languages
Available languages
Wear ear protection.
The typical weighted root mean square acceleration
value is not more than 2.5 m/s
These values have been obtained according to
EN50144.
For Model GA9030,GA9030F,GA9030S,GA9030SF
For European countries only
Noise and Vibration
The typical A-weighted noise levels are
sound pressure level: 91 dB (A)
sound power level: 104 dB (A)
Wear ear protection.
The typical weighted root mean square acceleration
value is not more than 2.5 m/s
These values have been obtained according to
EN50144.
For Model GA7040S,GA7040SF
For European countries only
Noise and Vibration
The typical A-weighted noise levels are
sound pressure level: 90 dB (A)
sound power level: 103 dB (A)
Wear ear protection.
The typical weighted root mean square acceleration
value is not more than 2.5 m/s
These values have been obtained according to
EN50144.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this
product is in compliance with the following standards of
standardized documents;
EN50144, EN55014, EN61000 in accordance with
Council Directives, 89/336/EEC, 98/37/EC.
Yasuhiko Kanzaki CE2006
000087
MAKITA INTERNATIONAL EUROPE LTD.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
Responsible manufacturer:
Makita Corporation Anjo Aichi Japan
ADDITIONAL SAFETY RULES
1.
Always use eye and ear protection. Other
personal protective equipment such as dust
mask, gloves, helmet and apron should be
worn.
2.
Always be sure that the tool is switched off
and unplugged before carrying out any work
on the tool.
3.
Keep guards in place.
4.
Use only wheels with correct size and wheels
2
.
2
.
2
.
Director
having a maximum operating speed at least as
high as the highest No Load Speed marked on
the tool's nameplate. When using depressed
center
fiberglass-reinforced wheels.
5.
Check the wheel carefully for cracks or
ENG021-1
damage before operation. Replace cracked or
damaged wheel immediately.
6.
Observe the instructions of the manufacturer
for correct mounting and use of wheels.
Handle and store wheels with care.
7.
Do not use separate reducing bushings or
adaptors to adapt large hole abrasive wheels.
8.
Use only flanges specified for this tool.
9.
Do not damage the spindle, the flange
(especially the installing surface) or the lock
nut. Damage to these parts could result in
wheel breakage.
ENG021-1
10. For tools intended to be fitted with threaded
hole wheel, ensure that the thread in the wheel
is long enough to accept the spindle length.
11.
Before using the tool on an actual workpiece,
test run the tool at the highest no load speed
for at least 30 seconds in a safe position. Stop
immediately if there is any vibration or
wobbling that could indicate poor installation
or a poorly balanced wheel. Check the tool to
determine the cause.
12. Check
ENH001-6
supported.
13. Hold the tool firmly.
14. Keep hands away from rotating parts.
15. Make sure the wheel is not contacting the
workpiece before the switch is turned on.
16. Use the specified surface of the wheel to
perform the grinding.
17. Do not use cutting off wheel for side grinding.
18. Watch out for flying sparks. Hold the tool so
that sparks fly away from you and other
persons or flammable materials.
19. Pay attention that the wheel continues to
rotate after the tool is switched off.
20. Do not touch the workpiece immediately after
operation; it may be extremely hot and could
burn your skin.
21. Position the tool so that the power cord
always stays behind the machine during
ENB031-6
operation.
22. If working place is extremely hot and humid, or
badly polluted by conductive dust, use a
short-circuit breaker (30 mA) to assure
operator safety.
23. Do not use the tool on any materials
containing asbestos.
24. Do not use water or grinding lubricant.
25. Ensure that ventilation openings are kept clear
when working in dusty conditions. If it should
become
5
wheels,
be
sure
that
the
workpiece
necessary
to
clear
to
use
only
is
properly
dust,
first
Table of Contents
