Sony TRINITRON BVM-D9H1U Maintenance Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Monitor
  5. TRINITRON BVM-D9H1U
  6. Maintenance manual

Sony TRINITRON BVM-D9H1U Maintenance Manual

Color video monitor chassis no. scc-p31c-a; scc-g10d-a; scc-g09f-a; scc-p31f-a; scc-g10g-a; scc-g09g-a
Hide thumbs Also See for TRINITRON BVM-D9H1U:
Table of Contents

Quick Links

See also: Operating Manual
TRINITRON
BVM-D9H1A
BVM-D9H1E
BVM-D9H1U
BVM-D9H5A
BVM-D9H5E
BVM-D9H5U
MAINTENANCE MANUAL
1st Edition
Serial No. 2000001 and Higher (ALL MODELS)
COLOR VIDEO MONITOR
®
CHASSIS NO. SCC-P31C-A
CHASSIS NO. SCC-G10D-A
CHASSIS NO. SCC-G09F-A
CHASSIS NO. SCC-P31F-A
CHASSIS NO. SCC-G10G-A
CHASSIS NO. SCC-G09G-A
Table of Contents
loading

Related Manuals for Sony TRINITRON BVM-D9H1U

Summary of Contents for Sony TRINITRON BVM-D9H1U

  • Page 1 TRINITRON COLOR VIDEO MONITOR ® BVM-D9H1A CHASSIS NO. SCC-P31C-A BVM-D9H1E CHASSIS NO. SCC-G10D-A BVM-D9H1U CHASSIS NO. SCC-G09F-A BVM-D9H5A CHASSIS NO. SCC-P31F-A BVM-D9H5E CHASSIS NO. SCC-G10G-A BVM-D9H5U CHASSIS NO. SCC-G09G-A MAINTENANCE MANUAL 1st Edition Serial No. 2000001 and Higher (ALL MODELS)
  • Page 2 LES SCHÉMAS DE PRINCIPE, LES VUES EXPLOSÉES ET LES CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO- LISTES DE PIECES SONT D’UNE IMPORTANCE CRITIQUE NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR POUR LA SÉCURITÉ DU FONCTIONNEMENT. NE LES AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- REMPLACER QUE PAR DES COMPOSANTS SONY DONT LE LISHED BY SONY.

  • Page 3: Table Of Contents

    Table of Contents 1. Operating Instructions BVM-D9H1J/D9H1U/D9H1E/D9H1A/D9H5J/D9H5U/D9H5E/D9H5A D14H1J/D14H1U/D14H1E/D14H1A/D14H5J/D14H5U/D14H5E/D14H5A ........................1-1 2. Service Informations 2-1. Circuit Boards Location (1/2) ..............2-1 2-2. Circuit Boards Location (2/2) ..............2-1 2-2-1. Cabinet Assy Removal ............... 2-2 2-2-2. Control Panel Complete Assy Removal (D9H5) ....... 2-3 2-2-3.
  • Page 4 4. Safety Related Adjustments +B (12 V) Voltage Check ............4-2 High Voltage Regulator Check ..........4-2 High Voltage Hold-Down Check ..........4-3 ABL Check ................. 4-3 Beam Current Protector Check ..........4-4 5. Circuit Adjustments 5-1. B Board Adjustments .................. 5-1 RGB Signal Adjustment .............
  • Page 5 10. Block Diagrams Overall (1/2) ....................10-1 Overall (2/2) ....................10-2 BC (1/2), BX, B1, B2 ................10-3 BC (2/2), C ....................10-4 D (1/2) ....................... 10-5 D (2/2), G1 ....................10-6 P ......................... 10-7 MA, MB ....................10-8 HA, HB, HC ....................10-9 11.
  • Page 6 Printed Wiring Boards ....................11-3 ....................11-6 ....................11-12 ....................11-13 ....................11-14 ....................11-17 ....................11-18 ....................11-22 ....................11-24 ....................11-28 HA, HB, HD ..................11-30 YA, YB ....................11-33 ....................11-34 ....................11-36 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 7 TRINITRON COLOR VIDEO MONITOR ® BVM-D9H1J/D9H1U/D9H1E/D9H1A BVM-D9H5J/D9H5U/D9H5E/D9H5A BVM-D14H1J/D14H1U/D14H1E/D14H1A BVM-D14H5J/D14H5U/D14H5E/D14H5A OPERATION MANUAL [Japanese/English] 1st Edition Serial No. 2000001 and Higher...
  • Page 8 CAUTION: For customers in the USA For the customers in Europe WARNING Danger of explosion if battery is incorrectly replaced. (BVM-D9H1U/D9H5U, BVM-D14H1U/D14H5U) (BVM-D9H1E/D9H1A/D9H5E/D9H5A, BVM-D14H1E/ Replace only with the same or equivalent type recommended This equipment has been tested and found to comply with D14H1A/D14H5E/D14H5A) To prevent fire or shock hazard, do not by the manufacturer.
  • Page 9 Table of Contents ATTENTION - When the product is installed in a rack: Achtung - bei Installation des Geräts in einem Gestell: Precautions ..................3(E) Chapter 1 a) Elevated operating ambient temperature a) Erhöhte Umgebungstemperatur bei Betrieb Overview .................... 4(E) Overview If installed in a closed or multi-unit rack assembly, the Wird das Gerät in einem geschlossenen Gestell oder...

  • Page 10: Precautions

    If you have any questions about this unit, contact your Overview .................43(E) used for several days or more. authorized Sony dealer. Structure of the ALIGNMENT Menu ........43(E) • Disconnect the power cord from the AC outlet by Setting Lists of the ALIGNMENT Menu .......43(E) grasping the plug, not by pulling the cord.

  • Page 11: Features

    The input connector configuration can be D14H1E/D14H1A in an EIA standard 19-inch rack. • Operable by using a Sony lithium ion battery (BP- easily modified and up to three adaptors can be L60/L90A) or DC 12 V external power source.

  • Page 12: Location And Function Of Parts

    Location and Function of Parts Overview BKM-120D SDI 4:2:2 Input Adaptor BVM-D9H1U/D9H1E/D9H1A/D9H5U/D9H5E/D9H5A Front Panel Includes a decoder for serial digital component signals. D1 SDI input/output connectors for two serial digital For the BVM-D14H1U/D14H1E/D14H1A/D14H5U/D14H5E/D14H5A, see pages 16(E) to 20(E). channels and active loop-through output connectors. BVM-D9H1U/D9H1E/D9H1A BKM-127W NTSC/PAL Input Adaptor Includes decoders for analog composite NTSC and...
  • Page 13 Location and Function of Parts !¡ MANUAL adjustment knobs !£ Function buttons This manual explains the location and function of parts Note and controls of the BVM-D9H5U/D9H5E/D9H5A. Each press of one of these knobs turns the knob’s Change the operation conditions for the monitor. When the STANDBY lamp 2 is blinking, the monitor The explanation also applies to the optional BKM- green LED on or off.
  • Page 14 Location and Function of Parts Function buttons in SHIFT OFF mode (LEDs of function buttons in green) Function buttons in SHIFT ON mode (LEDs of function buttons in amber) (Underscan) button: When this button is pushed in (ON), 16:9 button: When this button is pushed in (ON), the aspect the picture is underscanned by 3%, and four ends of the ratio changes to 16:9, and when set to OFF, the aspect raster is displayed on the screen.

  • Page 15: Bvm-D9H1U/D9H1E/D9H1A/D9H5U/D9H5E/D9H5A Rear Panel

    Location and Function of Parts 1 PARALLEL REMOTE1/2 connectors 2 DC 12V IN jack (XLR-type, 4-pin) BVM-D9H1U/D9H1E/D9H1A/D9H5U/D9H5E/D9H5A Rear Panel (1: female, D-sub 9-pin, 2: modular connector) Connects the DC 12V external power source to use the Form a parallel switch and controls the monitor monitor.
  • Page 16 Location and Function of Parts 7 Analog input/output connectors (BKM-129X) Attaching the AC adaptor or battery Connecting the AC power cord For connecting the BKM-10R Monitor Control Unit Attaching Connect the monitor and control unit using a cable Attach the AC adaptor to the monitor, and then ANALOG connect the supplied AC power cord.

  • Page 17: Bvm-D14H1U/D14H1E/D14H1A/D14H5U/D14H5E/D14H5A Front Panel

    Location and Function of Parts This manual explains the location and function of parts BVM-D14H1U/D14H1E/D14H1A/D14H5U/D14H5E/D14H5A Front Panel and controls of the BVM-D14H5U/D14H5E/D14H5A. INPUT The explanation also applies to the optional BKM- Numeric buttons BVM-D14H5U/D14H5E/D14H5A 10R/11R Monitor Control Unit. 1 Tally lamp Ent button: Confirms the With factory settings, the tally lamp lights as follows values and characters entered...
  • Page 18 For more information about the ADDRESS menu, see “Selecting the Monitor to 39(E). Control — ADDRESS Menu” on page 45(E). 9 OVER LOAD lamp Lights when some malfunction has occured. When the OVER LOAD lamp is lit, consult your nearest Sony service facilities.

  • Page 19: Bvm-D14H1U/D14H1E/D14H1A/D14H5U/D14H5E/D14H5A Rear Panel

    Location and Function of Parts Function buttons in SHIFT ON mode (LEDs of function buttons in amber) BVM-D14H1U/D14H1E/D14H1A/D14H5U/D14H5E/D14H5A Rear Panel BVM-D14H5U/D14H5E/D14H5A 16:9 button: When this button is pushed in (ON), the aspect ratio changes to 16:9, and when set to OFF, the aspect ratio changes to 4:3. The aspect ratio is fixed to 16:9 when the signal other than 4:3 signal format is input.
  • Page 20 Location and Function of Parts 1 PARALLEL REMOTE1/2 connectors 4 Analog input/output connectors (BKM-129X) 6 AC IN connector (3-pin) To switch each function between on and off or (1: female, D-sub 9-pin, 2: modular connector) between enable and disable, change pin connections in Connects the monitor to an AC power source, via the Form a parallel switch and controls the monitor the following way.

  • Page 21: Installation Of The 4:3 Mask

    Installation of the 4:3 Mask Basic Menu Operations When the aspect ratio is switched from 16:9 to 4:3, BVM-D14H1U/D14H1E/D14H1A/ Menu Operation Buttons replace the 16:9 mask with the supplied 4:3 mask. D14H5U/D14H5E/D14H5A The menus are operated using the menu operation BVM-D9H1U/D9H1E/D9H1A/ buttons on the front panel of the monitor or BKM- Installing the 4:3 mask...

  • Page 22: Displaying The Menus

    Basic Menu Operations Repeat steps 2 and 3 until the desired menu is Choosing one of two or more selections Displaying the Menus Menu Operation displayed. For more information about setting and Selecting in setting mode Press the MENU button. Follow the steps described below to display the menu adjustments, see below.

  • Page 23: Address Menu

    Basic Menu Operations Press the ENTER or Ent button. Entering a numerical value ADDRESS Menu “?” is displayed in yellow. The “?” indicates the position where character input is possible. Using the UP/DOWN buttons or PHASE knob, In addition to the menus displayed on the menu list, the C H A N N E L N A M E move the cursor to the desired item and press the...

  • Page 24: Menu Structure

    Preset Adjustment of the Picture Level Control Menu Structure Knobs — CONTROL PRESET ADJ Menu Menus consist of one to three levels. Overview Detailed information on the levels of menus is The preliminary adjustments of chroma, phase, Preset values can be set in the following two ways: described at the top of explanation of each menu.

  • Page 25: Control Preset Adj Menu

    D9H5U/D9H5E/D9H5A is small. So, when a probe adjustment, press the ENTER or Ent button to confirm other than the Sony BKM-14L is used, use the probe the adjusted values. • Knob adjustment (MANUAL menu) closely to the CRT screen.

  • Page 26: Setting Lists In The Color Temp Adj Menu

    Setting the Input Configuration B Adjusting the Color Temperature — COLOR TEMP ADJ Menu — INPUT CONFIG Menu Setting Lists in the COLOR TEMP ADJ Menu Overview This section explains the setting lists displayed in the Note You can set up to nine input channels. To assign D1 serial digital signals menu.

  • Page 27: Setting Lists In The Input Config Menu

    Assigning the Remote Control Functions C Setting the Input Configuration — INPUT CONFIG Menu — REMOTE Menu Setting Lists in the INPUT CONFIG Menu Overview PARALLEL REMOTE 1 and 2 are connected This section explains the setting lists displayed in the H PHASE: Set the horizontal picture position (–128 to The remote control functions are set with the menu.

  • Page 28: D Assigning The Remote Control Functions - Remote Menu

    Setting the Power-Up Conditions and Data about D Assigning the Remote Control Functions — REMOTE Menu the Screen Display — SYSTEM CONFIG Menu Setting Lists of the REMOTE Menu Overview This section explains the setting lists displayed in the The SYSTEM CONFIG menu is displayed on the two monitor.

  • Page 29: Menu

    E Setting the Power-Up Conditions and Data about the Screen Display — SYSTEM CONFIG Menu CONT/BRT HOLD: Select the contrast and [AUTO]: Disappears after displayed for a while. Structure of the SYSTEM CONFIG Menu brightness settings to the center or adjusted value ON: Displayed.

  • Page 30: F Displaying Information About The Monitor - Status Menu

    Displaying Information About the Monitor Adjusting the Position, Size and Geometry of — STATUS Menu the Picture — ALIGNMENT Menu Overview Overview The STATUS menu is used to view general data about • Data about the current channel (STATUS menu The ALIGNMENT menu is used for adjusting the the monitor and information about signals assigned to (1/2))

  • Page 31: Selecting The Monitor To Control - Address Menu

    Selecting the Monitor to Control G Adjusting the Position, Size and Geometry of the Picture — ALIGNMENT Menu — ADDRESS Menu [G] ALIGNMENT menu Overview A D D R E S S Adjust the position, size or geometry of the picture - - - with the UP and DOWN buttons or PHASE knob.

  • Page 32: Exiting The Address Menu

    Specifications Selecting the Monitor to Control — ADDRESS Menu Nominal chromaticity coordinates: General Cancelling the Remote Control Short-cut Function in the Mode ADDRESS Menu EBU phosphor System 15.625 kHz – 45 kHz (For details, see “Available Signal To cancel the remote control mode, press the When selecting the monitor, short-cut function will 0.640 0.330...
  • Page 33 Specifications Dimensional drawing BVM-D9H5U/D9H5E/D9H5A BVM-D14H1U/D14H1E/D14H1A BVM-D14H5U/D14H5E/D14H5A Unit: mm (inches) Unit: mm (inches) Unit: mm (inches) BVM-D9H1U/D9H1E/D9H1A Front Front Front Unit: mm (inches) Front ∅20 ∅22 ( 163 (6 163 (6 217 (8 217 (8 260 (10 Side 340 (13 352.5 (14) 12 ( 346 (13 482 (19)
  • Page 34 Specifications Mass BVM-D9H1U/D9H1E/D9H1A: Power requirements Convergence error Video signal approx. 8.1 kg (17 lb 14 oz) BVM-D9H1U/D9H1E/D9H1A/ Within a central area bounded by a when the AC adaptor is installed: circle with a diameter equal to the D9H5U/D9H5E/D9H5A: Frequency response approx.

  • Page 35: Available Signal Format

    Specifications Accessories supplied Available Signal Format AC power cord (1) Total lines Active ** Frame AC adaptor (1) (BVM-D9H1U/D9H1E/D9H1A/ System per frame lines per rate (Hz) Standard Scanning format Aspect D9H5U/D9H5E/D9H5A only) frame AC plug holder (1) 575/50I (*PAL) 2:1 interlace 16:9/4:3 ITU 601 Tally plate (1)

  • Page 36: Connection Cable Specifications For Color Temperature Probes

    Special cables are required to connect color The following diagrams show specifications and pin Modular connector Mini DIN 8-pin connector temperature probes other than the Sony BKM-14L to assignments for the required cables. (male) the monitor. Connection cable for GRASEBY SLS 9400 probe...

  • Page 37: Menu Index

    Menu Index The menu index shows the menu items provided with Menu Item Page Menu number Main menu this monitor in alphabetical order. For you reference, MAINTENANCE 40(E) [E5] SYSTEM CONFIG menu each menu item is followed by the page of this manual MANUAL 32(E) [A1]...

  • Page 38: Menu Configuration

    Menu Configuration MAIN MENU MAIN MENU M E N U M E N U M A N U A L Set the preset value with the C O N T R O L P R E S E T A D J . . . C O N T R O L P R E S E T A D J .

  • Page 39: Service Informations

    Section 2 Service Informations 2-1. Circuit Boards Location (1/2) 2-1. Circuit Boards Location (2/2) HB (D9H5) HA (D9H5) HC (D9H5) HD (D9H5) BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...

  • Page 40: Cabinet Assy Removal

    2-2-1. Cabinet Assy Removal 5 Screw (+B 3 × 8) 6 Cabinet assy 4 Four screws (Case screw OS) 3 Four screws (Case screw OS) 2 Remove power unit complete assy in the 1 Push lever in the direction shown by the arrow B. direction shown by the arrow A.

  • Page 41: Control Panel Complete Assy Removal (D9H5)

    2-2-2. Control Panel Complete Assy Removal (D9H5) Connector (9P) 2 Screw (+BVTT 3 × 6) CN3203 1 Screw (+BVTT 3 × 6) 3 Control panel complete assy 2-2-3. HA and HB Boards Removal (D9H5) 4 Three screws (+BVTP 3 × 8) 5 HB board Spacer 7 HA board...

  • Page 42: Hc And Hd Boards Removal (D9H5)

    2-2-4. HC and HD Boards Removal (D9H5) 3 Three screws (+BVTP 3 × 8) 5 Four screws 1 Two screws (+BVTP 3 × 6) (+BVTT 3 × 6) 6 HC board 2 Rear cover 4 HD board 2-2-5. YA and YB Boards Removal PC support 6 YA board CN900...

  • Page 43: B, B1 And B2 Boards Removal

    2-2-6. B, B1 and B2 Boards Removal 3 B1 board 4 B2 board Two claws 1 Four screws (+BVTT 3 × 6) 2 Open B board in the direction shown by the arrow. 2-2-7. How to Open D Board 2 Open D board in the direction shown by the arrow.

  • Page 44: P Board Removal

    2-2-8. P Board Removal CN505 3 Two screws (+BVTT 3 × 6) CN503 CN501 CN506 4 Remove P board in the direction shown by the arrow. 1 D board (Refer to 2-2-7.) 2 Insulator BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...

  • Page 45: Bx Board (Bkm-129X) Removal And Check

    2-2-9. BX Board (BKM-129X) Removal and Check 3 Z COMPL (Part No. : A-1394-977-A) ∗ Insert the Z COMPL into the slot and insert the BX board (BKM-129X) into the connector on the Z COMPL. Three slots 1 Loosen two stopper screws.

  • Page 46: T Board Removal

    2-2-10. T Board Removal 1 Two blank panel assy CN801 CN805 CN806 4 T board 2 BX board (BKM-129X) 3 Four screws (+BVTT 3 × 6) 2-2-11. M Block Assy (MA and MB Boards) Removal 7 Screw (+BVTT 3 × 6) 8 Remove M shield 1 D board in the direction shown by the arrow.

  • Page 47: G Board Removal

    2-2-12. G Board Removal * Remove the power unit complete assy. (Refer to 2-2-1.) 1 Three screws (+K 3 × 6) 2 Power case (Top) assy 3 Four screws (+PSW 3 × 8) 4 G board 5 Insulated sheet (Bottom) Power case (Bottom) assy BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...

  • Page 48: Picture Tube Removal

    2-2-13. Picture Tube Removal CN2504 4 Anode cap 7 Four flange nuts (M5) 2 Two screws (+BVTT 3 × 6) 5 C board 6 Deflection yoke 8 Picrure tube 3 Front assy 1 Two screws (+BVTT 3 × 6) • REMOVAL OF ANODE CAP Note: To eliminate electric shock hazard, when replacing the picture tube, short-circuit the anode of the picture tube and the high-voltage terminal of anode cap to the picture tube shield or carbon painted on the picture tube, after removing the anode.

  • Page 49: Set-Up Adjustments

    Section 3 Set-Up Adjustments 3-1. Set-Up Adjustment When CRT is Replaced This section describes the adjustments to be performed when the CRT is replaced. [Preparations] ..Required tools and measuring instruments ..Setting the INPUT CONFIGURATION menu 1.
  • Page 50 ..Connection diagram Y/G terminal /B terminal /R terminal SYNC terminal SLOT No. 1 Component signal generator BKM-129X (BX Board) BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...

  • Page 51: [Focus Adjustment]

    [Focus Adjustment] [Landing Adjustment] 1. Connect the 1080/60i cross-hatch signal (see note) to 1. Connect the 480/60i entire-white signal (see note) to the ANALOG Y/G input connector. the ANALOG Y/G input connector. Note: This is the 1125 (1080) cross-hatch signal. Note: This is the NTSC entire-white signal.

  • Page 52: [H. Blanking Adjustment]

    [H. Blanking Adjustment] ..Preparation 10. Connect the 480/60i cross-hatch signal (see note) to the ANALOG Y/G input connector. 1. Connect the monoscope signal of the signal formats Note: This is the NTSC cross-hatch signal. that are shown in the following table, to the ANALOG 11.
  • Page 53 ..H. Blanking Adjustment 1. Press the SHIFT button to ON. [The LED (orange) on 8. Adjust the H. PHASE data so that the monoscope top of the button turns on.] picture is position just in the center of the raster (so that C = D).

  • Page 54: [V. Blanking Adjustment]

    [V. Blanking Adjustment] [Linearity Adjustment] ..Preparation ..Linearity Adjustment (1) 1. Connect the monoscope signal of the signal formats that are 1. Connect the 1080/60i (1125) cross-hatch signal to the shown in the following table, to the ANALOG Y/G input ANALOG Y/G input connector.
  • Page 55 . Linearity Adjustment (2) Note 2)The following adjustment menus are located in the Note 1)Connect the monoscope signal or the cross-hatch directory under the DEFLECTION menu of the signal having the following signal formats as MAINTENANCE menu. shown in the table below, to the ANALOG Y/G H SIZE input connector.

  • Page 56: [Convergence Adjustment]

    [Convergence Adjustment] . Preparation V LIN BAL 1. Connect the 480/60p cross-hatch signal to the ANA- LOG Y/G input connector. 2. Press the SHIFT button to ON. [The LED (orange) on V LIN AMP top of the button turns on.] 3.

  • Page 57: [Static Convergence Adjustment]

    [Static Convergence Adjustment] [Dynamic Convergence Adjustment] ..Horizontal Static Convergence Adjustment 1. Minimize the vertical misconvergence in the left-most 1. Adjust RV701 on the C board so that the red dots and end of the center of a screen and in the right-most end the green dots are correctly converged.

  • Page 58: [G2 Adjustment]

    [G2 Adjustment] 1. Turn off the POWER switch. This monitor has the copy function of the color temperature 2. Disconnect the connector CN701 from the C board. data between two or more monitors. 3. Apply the following DC voltage to pin-1, pin-3 and However, the CRT drive voltage are unique in every pin-5 of CN701 on the C board respectively.
  • Page 59 2. Preparation for Adjustment 11. After selecting the COLOR1 item of the COLOR 2.1 Connect the 480/60i (525) WINDOW signal to the TEMP menu, select D65. Copy the D65 color temper- ANALOG Y/G input connector. ature data to COLOR1. 2.2 Connect the RS-232C connector of a color analyzer 12.
  • Page 60 15. Connect the 1080/60i 100 IRE WINDOW signal to the 3.3 White Balance Adjustment (2) ANALOG Y/G input connector. 1. Connect the 480/60i (525) 20 IRE WINDOW color 16. Adjust SUB CONTRAST so that luminance becomes difference signal to the ANALOG Y/G input connec- 120 cd/m tor.
  • Page 61 3.6 White Balance Adjustment (5) 1. Turn off the main POWER switch. 2. Insert the BKM-120D into the SLOT 2. 3. Connect the D1-SDI 20 IRE WINDOW signal to the BKM-120D. 4. Turn on the main POWER switch. 5. Select D1-SDI using the FORMAT menu of the INPUT CONFIG menu.
  • Page 62 3-14 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...

  • Page 63: Safety Related Adjustments

    Section 4 Safety Related Adjustments This section describes the adjustment procedure that is . Set the INPUT CONFIGURATION menu required when the safety related parts are replaced. Set the INPUT CONFIGURATION menu of the SETUP menu as shown below unless otherwise specified. [Preparation] FORMAT ........

  • Page 64: B (12 V) Voltage Check

    +B (12 V) Voltage Check High Voltage Regulator Check When the following parts (the parts to which the mark is When the following parts (the parts to which the mark is attached on the schematic diagram) are replaced, be sure to attached on the schematic diagram) are replaced, be sure to perform the following checks.

  • Page 65: High Voltage Hold-Down Check

    High Voltage Hold-Down Check ABL Check When the following parts (the parts to which the mark is When the following parts (the parts to which the mark is attached on the schematic diagram) are replaced, be sure to attached on the schematic diagram) are replaced, be sure to perform the following checks.

  • Page 66: Beam Current Protector Check

    Beam Current Protector Check When the following parts (the parts to which the mark is attached on the schematic diagram) are replaced, be sure to perform the following checks. P board ..R582, R583, R584, R585, R586, R1504, R1505, R1506 1.

  • Page 67: Circuit Adjustments

    Section 5 Circuit Adjustments 5-1. B Board Adjustments This section describes the following adjustments that are Control Settings ..Set the INPUT CONFIGURATION menu of the SETUP required when the parts are replaced or maintenance is performed in the B board.
  • Page 68 Connection (2) B Board -side A- CN301 TP302 TP304 TP303 TP1301 TP1300 TP1302 Adjustment Procedure 1. RGB Signal Adjustment Status During Adjustment Specifications Adjustment Point Step 1 Adjust the GREEN waveforms to have Use the adjustment menu Y/G BLACK ..Input the 15 kHz/60 Hz the same amplitude at TP302.

  • Page 69: K Ypbpr Smpte (709) Signal Adjustment

    2. 15k YPBPR SMPTE (709) Signal Adjustment 2-1. BLACK Level Adjustment Status During Adjustment Specifications Adjustment Point Step 1 Make flat the pedestal portion of the Use the adjustment menu Y/G BLACK ..Input the 15 kHz/60 Hz YPBPR Y-signal waveform at TP302.
  • Page 70 2-3. MATRIX Adjustment Status During Adjustment Specifications Adjustment Point Step 1 GREEN waveform amplitude at TP1301: Use the adjustment menu Y LEVEL 560 ± 20 mVp-p ..Input the 15 kHz/60 Hz YPBPR (50H) that is located under the directory SMPTE (709) 100% color bar signal.

  • Page 71: K Ypbpr Smpte (601) Signal Adjustment

    3. 15k YPBPR SMPTE (601) Signal Adjustment Status During Adjustment Specifications Adjustment Point Step 1 GREEN waveform amplitude at TP1301: Use the adjustment menu Y LEVEL 560 ± 20 mVp-p ..Input the 15 kHz/60 Hz YPBPR (51H) that is located under the directory SMPTE (601) 100% color bar signal.

  • Page 72: K Ypbpr Betacam Setup 0 (601) Signal Adjustment

    4. 15k YPBPR BETACAM SETUP 0 (601) Signal Adjustment Status During Adjustment Specifications Adjustment Point Step 1 GREEN waveform amplitude at TP1301: Use the adjustment menu Y LEVEL ..Input the 15 kHz/60 Hz YPBPR BETACAM 560 ± 20 mVp-p (52H) that is located under the directory SETUP 0 (601) 75% color bar signal.

  • Page 73: Ypbpr Betacam Setup 7.5 (601) Signal Adjustment

    5. 15k YPBPR BETACAM SETUP 7.5 (601) Signal Adjustment Status During Adjustment Specifications Adjustment Point Step 1 Make flat the pedestal portion of the Use the adjustment menu Y/G BLACK ..Input the 15 kHz/60 Hz YPBPR Y-signal waveform at TP302.

  • Page 74: Ypbpr Smpte (709) Signal Adjustment

    6. 33k YPBPR SMPTE (709) Signal Adjustment Status During Adjustment Specifications Adjustment Point Step 1 Make flat the PB waveform at TP303. Use the adjustment menu PB/B BLACK Level difference: 0 ± 10 mV ..Input the 33 kHz/60 Hz YPBPR (33H) that is located under the directory SMPTE (709) 100% color bar signal.

  • Page 75: Circuit Descriptions

    Section 6 Circuit Descriptions This section describes the circuit operations of the follow- FET is turned off. Then an electric current flows through ing boards used in the BVM-D9H1/D9H5. the boost diode where the current decreases with the slope of -(Vpfc - Vin (rms))/L. When this current reaches 0, the 6-1.

  • Page 76: B Board

    6-2. B board 5. OSD Insertion Circuit The on-screen display of the R-signal is realized by 1. Clamp Circuit (1) inserting the OSD blanking with IC1300 (2/3) and by The signal that is selected by the option board is input to inserting the OSD characters with IC1304 (1/3).

  • Page 77: Ma Board

    6-3. MA board 10. B1 Board The B1 board is an aperture correction circuit. 1. System Control The aperture correction performs the frequency compensa- IC106 (system control CPU) controls the monitor in tion at 5 MHz when the input signal is 480/60i and 575/ accordance with the program that is installed in IC108 501 with DL400/DL401.

  • Page 78: D Board P1 And P2

    6-5. D Board P1 and P2 This output is also controlled by the output signal from microprocessor in the same manner as in the case of ± 6 V 1. D board - P1 power. The P1 block of the D board is the DC-DC converter The floating power voltages (HC+, HC_ and HC N) are circuit that generates the following power voltages to be generated by rectifying and smoothing out the output...
  • Page 79 The deflection signal processor IC2503 has the built-in voltage. Relationship between DC. IN and +B voltage is protector for X-ray irradiation. When its pin-15 is raised shown below. to 8 V or higher, the X-ray protection circuit starts V (+B) = DC. IN + V (L2503) working to stop the horizontal and vertical outputs.

  • Page 80: P Board

    6-6. P Board choke coil that is inserted to raise the +B voltage during 15 kHz input mode. Q2519 is the switch to add the S- shape capacitor for 15 k and 30 k to the circuit, and is The P board consists of the PWM circuit for horizontal driven by Q2522 and Q2523.
  • Page 81 2. + B Power Supply for High Voltage Output tension voltage of the monitor, focus voltage, G2 voltage, The + B power supply for high voltage output consists of heater voltage and high voltage protector detected output Q515, L501, D520, C535, C583 and other devices. voltage.

  • Page 82: Ha, Hb And Hc Boards

    pull up the Ik detection terminal to 12 V in order to C518.) The signal that is output from IC503 pins-9 and - prevent the protector circuit from erroneous operation. 10 is sent to IC506 pins-10 and -12 to generate the signal The operating point of the Ik protector is ABL current = that drives the FET in the subsequent circuit.

  • Page 83: Semiconductors

    Section 7 Semiconductors CXA1544M-T6 LC35256DM-70-TLM MC74HC00AFEL AN5265 NJU3716M-T2 MB90096PF-178 MC74HC08AF MB90096PF-G-127-BND-ER MC74HC589AFEL TC74HC30AF TC74VHC02F TC74VHC04F TC74VHC125F TC74VHC138F TC74VHC14F TOP VIEW TOP VIEW LM2990SX-5.0 BA05FP-E2 CXA1739S TOP VIEW MCR5102 TOP VIEW CXA1875AM-T4 MAX202CSE MAX3100CEE-TG068 LM2990T-5.0 BA05T MC74HC4053F BA09T MC74HC4538AF TC74HC4053AFT (EL) TC74HC4538AF TL1451ACPWR TL494CNS...
  • Page 84 IC, TRANSISTOR, DIODE SE-012N UPC1093J-1-T 2SC4686A (LBSONY) 1SS119-25 2SD2578-CA RD27ESB2 IRFI640 RD5.1SB3-T2 RD6.8SB2-T1 RD7.5ESB1 CATHODE 2SJ377 (TE16L) TC74VHC244F 2SK2231-TP TC74VHC574F Z8622812PSC ANODE 1SS226 TOP VIEW 2SA1037AK-T146-QR TOP VIEW 2SA1037AK-T146-R 2SA1330-06 TDA6111Q/N4 2SA1338-5-TB 2SA1462-T1Y33 2SA1462-Y33 2SK520K44K45-T1B 2SC1623-L5L6 2SC3326N-A 1SS352 2SC3360-N16 DTZ-TT11-5.6A 2SC3392-5-TB RD12SB2 2SC3545-T43...
  • Page 85 DIODE D1NL20U-TR DTZ-TT11-2.4B RM11C ERA91-02 CATHODE CATHODE CATHODE ANODE ANODE ANODE SLR-325MCT31 D30SC4M EC10QS-06 SLR-325VCT31 SC311-6-TE12RA SC802-04 SC802-06 ANODE CATHODE ANODE CATHODE MA111-(K8).S0 D4SB60L SML-020MLTT87 ANODE ANODE – CATHODE RD10SB1 CATHODE RD4.7SB1-T1 – RD6.2SB (D9H5) D5L60 RD18M-T1B2 RD22M-B CATHODE ANODE BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 86 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...

  • Page 87: Exploded Views

    CHASSIS Section 8 Exploded Views NOTE : • Items marked “ * ” are not stocked since they are seldom required The components identified marked ! are for routine service. Some delay should be anticipated when order- critical for safety. ing these items.

  • Page 88: Picture Tube

    PICTURE 8-2. PICTURE TUBE : 7-682-946-09 +PSW 3x5 : 7-682-948-09 +PSW 3x8 : 7-685-871-09 +BVTT 3x6 : 7-682-547-09 +B 3x6 : 7-627-556-58 +P 2.6x5 BKM-142HD BKM-127W BKM-120D OPTION Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark ! 8-737-658-05 PICTURE TUBE 09FX (DTV SPEC) * X-4037-178-1 PANEL ASSY, REAR (D9H1) 4-304-511-00 NUT (M5), FLANGE * X-4037-178-2 PANEL ASSY, REAR (D9H5)

  • Page 89: Power Unit

    UNIT 8-3. POWER UNIT : 7-682-549-09 +B 3x10 : 7-682-247-09 +K 3x6 : 7-682-961-01 +PSW 4x8 : 7-627-556-58 +P 2.6x5 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark 4-072-743-01 BRACKET, POWER * 4-628-904-02 SHOE, V * X-4037-169-1 CASE (BOTTOM) ASSY, POWER 4-072-700-01 NUT, PLATE * A-1316-460-A G COMPL 4-382-854-01 SCREW (M3X8), P, SW (+)
  • Page 90 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...

  • Page 91: Electrical Parts List

    Section 9 Electrical Parts List Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark NOTE : • Items marked “ * ” are not stocked since they are seldom required The components identified marked ! are for routine service. Some delay should be anticipated when ordering critical for safety.
  • Page 92 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark C1400 1-163-035-00 CERAMIC CHIP0.047µF C2370 1-107-746-11 ELECT 10µF 200V C1401 1-163-035-00 CERAMIC CHIP0.047µF C2371 1-163-021-91 CERAMIC CHIP0.01µF C1402 1-163-035-00 CERAMIC CHIP0.047µF C2372 1-163-021-91 CERAMIC CHIP0.01µF C1404 1-163-031-11 CERAMIC CHIP0.01µF C2373 1-163-021-91 CERAMIC CHIP0.01µF C1405 1-163-035-00 CERAMIC CHIP0.047µF...
  • Page 93 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark CN308 * 1-564-512-11 PLUG, CONNECTOR 9P IC3400 8-759-424-13 IC MC74HC00AFEL CN411 * 1-506-611-11 PIN, CONNECTOR 8P IC3401 8-759-032-14 IC MC74HC08AF CN412 * 1-506-611-11 PIN, CONNECTOR 8P IC3403 8-759-328-12 IC Z8622812PSC CN421 * 1-779-070-21 PIN, CONNECTOR 12P IC3404 8-759-527-74...
  • Page 94 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark Q1402 8-729-026-50 TRANSISTOR 2SA1037AK-T146-QR R306 1-216-025-91 RES,CHIP 1/10W Q1410 8-729-026-50 TRANSISTOR 2SA1037AK-T146-QR R307 1-216-653-11 METAL CHIP 1.2K 0.50% 1/10W Q1411 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R308 1-216-025-91 RES,CHIP 1/10W Q1412 8-729-026-50 TRANSISTOR 2SA1037AK-T146-QR R309 1-216-049-91 RES,CHIP 1/10W...
  • Page 95 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark R386 1-216-693-11 METAL CHIP 0.50% 1/10W R1312 1-216-073-00 RES,CHIP 1/10W R388 1-216-089-91 RES,CHIP 1/10W R1313 1-216-025-91 RES,CHIP 1/10W R389 1-216-025-91 RES,CHIP 1/10W R1314 1-216-057-00 RES,CHIP 2.2K 1/10W R390 1-216-057-00 RES,CHIP 2.2K 1/10W R1315...
  • Page 96 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark R1428 1-216-049-91 RES,CHIP 1/10W R2350 1-216-689-11 RES,CHIP 1/10W R1429 1-216-073-00 RES,CHIP 1/10W R2351 1-219-743-11 CARBON 1/2W R1430 1-216-095-00 RES,CHIP 1/10W R2352 1-216-085-00 RES,CHIP 1/10W R1431 1-216-041-00 RES,CHIP 1/10W R2353 1-216-085-00 RES,CHIP 1/10W R1432 1-216-049-91 RES,CHIP...
  • Page 97 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark R3323 1-216-659-11 METAL CHIP 2.2K 0.50% 1/10W R4300 1-216-073-00 RES,CHIP 1/10W R3324 1-216-655-11 METAL CHIP 1.5K 0.50% 1/10W R4301 1-216-073-00 RES,CHIP 1/10W R3325 1-216-041-00 RES,CHIP 1/10W R4302 1-216-073-00 RES,CHIP 1/10W R3326 1-216-029-00 RES,CHIP 1/10W...
  • Page 98 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark C404 1-163-031-11 CERAMIC CHIP0.01µF C407 1-163-038-91 CERAMIC CHIP0.1µF R400 1-216-025-91 RES,CHIP 1/10W C410 1-163-038-91 CERAMIC CHIP0.1µF R401 1-216-057-00 RES,CHIP 2.2K 1/10W C411 1-165-319-11 CERAMIC CHIP0.1µF R402 1-216-651-11 METAL CHIP 0.50% 1/10W C412 1-163-031-11 CERAMIC CHIP0.01µF...
  • Page 99 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark R521 1-216-037-00 RES,CHIP 1/10W R522 1-216-631-11 METAL CHIP 0.50% 1/10W R523 1-216-631-11 METAL CHIP 0.50% 1/10W IC3901 8-759-239-34 IC TC74HC4538AF R524 1-216-025-91 RES,CHIP 1/10W IC3902 8-759-523-02 IC TC74HC4053AFT(EL) R531 1-216-057-00 RES,CHIP 2.2K 1/10W...
  • Page 100 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark R3938 1-216-073-00 RES,CHIP 1/10W C501 1-128-526-11 ELECT 100µF R3939 1-216-097-91 RES,CHIP 100K 1/10W C502 1-163-038-91 CERAMIC CHIP0.1µF R3940 1-216-073-00 RES,CHIP 1/10W C503 1-163-038-91 CERAMIC CHIP0.1µF R3941 1-216-049-91 RES,CHIP 1/10W R3942 1-216-081-00 RES,CHIP 1/10W ...
  • Page 101 BX C Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark R207 1-216-025-91 RES,CHIP 1/10W R208 1-216-097-91 RES,CHIP 100K 1/10W R209 1-216-013-00 RES,CHIP 1/10W C701 1-162-114-00 CERAMIC 0.0047µF R301 1-214-837-11 METAL 1/2W C702 1-104-665-11 ELECT 100µF R302 1-216-089-91 RES,CHIP 1/10W C703 1-162-114-00...
  • Page 102 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark C1605 1-124-589-11 ELECT 47µF C2551 1-163-809-11 CERAMIC CHIP0.047µF 10% C1606 1-126-096-11 ELECT 10µF C2552 1-164-346-11 CERAMIC CHIP1µF C1607 1-163-031-11 CERAMIC CHIP0.01µF C2553 1-164-004-11 CERAMIC CHIP0.1µF C1608 1-163-037-11 CERAMIC CHIP0.022µF 10% C2554 1-126-176-11 ELECT 220µF...
  • Page 103 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark C2631 1-127-573-91 CERAMIC CHIP1µF CN2504 * 1-793-239-11 PIN, CONNECTOR (PC BOARD) 6P C3501 1-163-133-00 CERAMIC CHIP470PF CN2505 * 1-564-507-11 PLUG, CONNECTOR 4P C3502 1-107-877-11 ELECT 1000µF 20% CN2506 * 1-564-711-11 PIN, CONNECTOR (SMALL TYPE) 9P C3503 1-163-021-91...
  • Page 104 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark Q1608 1-801-806-11 TRANSISTOR DTC144EKA-T146 Q1609 1-801-806-11 TRANSISTOR DTC144EKA-T146 ! 1-533-183-11 HOLDER, FUSE Q1610 1-801-806-11 TRANSISTOR DTC144EKA-T146 ! 1-533-183-11 HOLDER, FUSE Q1611 8-729-120-28 TRANSISTOR 2SC1623-L5L6 ! 1-533-183-11 HOLDER, FUSE Q1612 8-729-824-24 TRANSISTOR 2SA1338-5-TB ! 1-533-183-11 HOLDER, FUSE...
  • Page 105 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark R1603 1-216-677-11 METAL CHIP 0.50% 1/10W R2542 1-216-359-00 METAL OXIDE 6.8 1W F R1605 1-216-065-91 RES,CHIP 4.7K 1/10W R2543 1-216-359-00 METAL OXIDE 6.8 1W F R1606 1-216-055-00 RES,CHIP 1.8K 1/10W R2545 1-202-933-61 FUSIBLE...
  • Page 106 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark R2620 1-216-065-91 RES,CHIP 4.7K 1/10W R3613 1-216-691-11 METAL CHIP 0.50% 1/10W R2625 1-216-065-91 RES,CHIP 4.7K 1/10W R3614 1-216-667-11 METAL CHIP 4.7K 0.50% 1/10W R2626 1-216-065-91 RES,CHIP 4.7K 1/10W R3615 1-216-662-11 METAL CHIP 0.50% 1/10W R2627 1-216-009-91 RES,CHIP...
  • Page 107 G HA Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark C637 1-107-910-11 ELECT 100µF R653 1-215-485-00 METAL 470K 1/4W C644 1-127-825-11 FILM 0.0033µF 3% R657 1-216-677-11 METAL CHIP 0.50% 1/10W C651 1-163-021-91 CERAMIC CHIP0.01µF R658 1-216-651-11 METAL CHIP 0.50% 1/10W C690 1-111-074-11 ELECT...
  • Page 108 HA HB Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark D203 8-719-073-01 DIODE MA111-(K8).S0 R218 1-216-089-91 RES,CHIP 1/10W D204 8-719-073-01 DIODE MA111-(K8).S0 R219 1-216-089-91 RES,CHIP 1/10W D205 8-719-073-01 DIODE MA111-(K8).S0 R220 1-216-089-91 RES,CHIP 1/10W D206 8-719-073-01 DIODE MA111-(K8).S0 R221 1-216-065-91 RES,CHIP 4.7K...
  • Page 109 HB HC Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark C1205 1-163-031-11 CERAMIC CHIP0.01µF 1-163-031-11 CERAMIC CHIP0.01µF C1206 1-163-031-11 CERAMIC CHIP0.01µF 1-163-031-11 CERAMIC CHIP0.01µF C1207 1-163-031-11 CERAMIC CHIP0.01µF 1-163-031-11 CERAMIC CHIP0.01µF 1-163-031-11 CERAMIC CHIP0.01µF 1-163-031-11 CERAMIC CHIP0.01µF 1-163-031-11 CERAMIC CHIP0.01µF CN1200 * 1-564-719-11 PIN, CONNECTOR (SMALL TYPE) 3P...
  • Page 110 HC HD Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark 1-412-537-31 INDUCTOR 100µH 1-767-892-21 VIBRATOR, CRYSTAL (20 MHz) 1-412-544-15 INDUCTOR 390µH **************************************************************** 1-216-073-00 RES,CHIP 1/10W * A-1372-677-A HD MOUNT (D9H5) 1-216-295-91 SHORT ****************** 1-216-073-00 RES,CHIP 1/10W 1-216-073-00 RES,CHIP 1/10W...
  • Page 111 HD MA Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark Q3202 8-729-026-50 TRANSISTOR 2SA1037AK-T146-QR C110 1-163-031-11 CERAMIC CHIP0.01µF Q3203 8-729-120-28 TRANSISTOR 2SC1623-L5L6 C111 1-126-392-11 ELECT CHIP 100µF 6.3V Q3205 1-801-806-11 TRANSISTOR DTC144EKA-T146 C112 1-126-392-11 ELECT CHIP 100µF 6.3V Q3206 1-801-806-11 TRANSISTOR DTC144EKA-T146 C113...
  • Page 112 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark D103 8-719-158-19 DIODE RD6.2SB R106 1-216-097-91 RES,CHIP 100K 1/10W D104 8-719-158-19 DIODE RD6.2SB R107 1-216-097-91 RES,CHIP 100K 1/10W D105 8-719-158-19 DIODE RD6.2SB (D9H5) R108 1-216-097-91 RES,CHIP 100K 1/10W R109 1-216-097-91 RES,CHIP 100K 1/10W D107...
  • Page 113 MA MB Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark R173 1-216-025-91 RES,CHIP 1/10W C1115 1-126-206-11 ELECT CHIP 100µF 6.3V R174 1-216-025-91 RES,CHIP 1/10W R177 1-216-025-91 RES,CHIP 1/10W C1116 1-163-031-11 CERAMIC CHIP0.01µF R178 1-216-053-00 RES,CHIP 1.5K 1/10W C1117 1-126-206-11 ELECT CHIP 100µF...
  • Page 114 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark D1103 8-719-158-19 DIODE RD6.2SB R1106 1-216-025-91 RES,CHIP 1/10W D1104 8-719-037-22 DIODE RD12SB-T1 R1107 1-216-025-91 RES,CHIP 1/10W R1108 1-216-025-91 RES,CHIP 1/10W D1105 8-719-037-22 DIODE RD12SB-T1 R1109 1-216-025-91 RES,CHIP 1/10W D1106 8-719-037-22 DIODE RD12SB-T1 R1110 1-216-025-91 RES,CHIP 1/10W...
  • Page 115 MB P Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark R1183 1-216-049-91 RES,CHIP 1/10W C514 1-163-005-11 CERAMIC CHIP470PF R1184 1-216-049-91 RES,CHIP 1/10W C515 1-107-903-11 ELECT 2.2µF R1185 1-216-049-91 RES,CHIP 1/10W C516 1-165-319-11 CERAMIC CHIP0.1µF R1186 1-216-295-91 SHORT 0 (D9H5) R1187 1-216-295-91 SHORT 0 (D9H5)
  • Page 116 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark C583 1-107-995-11 ELECT 100µF 160V IC506 8-759-185-47 IC IR2112 C584 1-107-889-11 ELECT 220µF IC507 8-759-198-31 IC UPC1093J-1-T IC508 8-759-502-80 IC LM358M C585 1-104-653-11 ELECT 220µF IC509 8-759-502-84 IC LM393M C587 1-163-021-91 CERAMIC CHIP0.01µF IC510 8-759-337-67 IC NJM2360AM(TE2)
  • Page 117 Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark R516 1-216-025-91 RES,CHIP 1/10W R582 1-216-693-11 METAL CHIP 0.50% 1/10W R517 1-216-073-00 RES,CHIP 1/10W R583 1-216-687-11 METAL CHIP 0.50% 1/10W R518 1-216-097-91 RES,CHIP 100K 1/10W R584 1-216-690-11 METAL CHIP 0.50% 1/10W R519 1-216-081-00 RES,CHIP 1/10W...
  • Page 118 T YA YB Ref.No. Part No. Description Remark Ref.No. Part No. Description Remark * A-1390-942-A T MOUNT ********* D951 8-719-060-27 DIODE SLR-325MCT31 D952 8-719-053-43 DIODE SLR-325VCT31 D953 8-719-037-22 DIODE RD12SB-T1 D954 8-719-037-22 DIODE RD12SB-T1 CN801 * 1-564-526-11 PLUG, CONNECTOR 11P D955 8-719-037-22 DIODE RD12SB-T1 CN802...

  • Page 119: Overall (1/2)

    Overall (1/2) Overall (1/2) Section 10 Block Diagrams Overall (1/2) BX (BKM-129X) IC300,303 Q404,405,411,412 IC1300,1305 Q101,102 Q300-302 Q303 IC306 IC410 Q406-409 Q1300-1302 DL404,405 IC1304 IC401 Q1431-1434 IC2345 Y/G CLAMP BUFF DELAY SELECT CUT OFF R VIDEO BUFF PULSE INSERT BUFF/AMP CLAMP SWITCH CLAMP...

  • Page 120: Overall (2/2)

    Overall (2/2) Overall (2/2) Overall (2/2) H SYNC H BLK H BLK MB BOARD V SYNC V BLK B BOARD IC2503 IC2506 IC2513 T2501 H DF IC2521 D2505 IC2505(1/2) H BLK H+B DRIVE IC2517 DC IN CONTROL SYNC Q2509 H SYNC PULSE GEN H BLK IC2512,Q2502...
  • Page 121 B (1/2), BX, B1, B2 B (1/2) /BX, B1, B2 B Block (1/2) BX Block B1 Block B2 Block SIGNAL SELECT (BKM-129X) (SIGNAL AMP) (1/2) (SIGNAL SELECT) TB001 SUB CPU IC410 CN401(1/2) TP101 TP300 ANALOG I/O IC300 CN401(2/2) TP302 BUFF BUFF CN001(2/2) CN301...
  • Page 122 B (2/2), C B (2/2), C B Block (2/2) C Block SIGNAL SELECT FROM(1/2) (2/2) RGB MATRIX IC401 IC1304 RGB MATRIX IC1305 (RGB OUT) IC1300 IC1304 TP2345 CLAMP IC1300 IC2345 IC1300 CN411(2/2) Q2345 CN305 CN701 B1 BOARD BUFF BUFF R BUFF BUFF BUFF BUFF...
  • Page 123 D (1/2) D (1/2) D Block (1/2) H/V OSC (1/2) DYNAMIC FOCUS CN2501 MB BOARD DC IN DC IN CN2502 CN1101 B BOARD(2/2) H SYNC H BLK CN303 V SYNC V BLK IC2523(1/2) BUFF V BLK PULSE GEN V TIM Q2531 VD BLK IC2503...
  • Page 124 D (2/2), G1 D (2/2), G1 D Block (2/2) G1 Block (2/2) T604 (REGULATER) (MAIN REG) D690 +13V RECT IC603 IC666 MAIN SWITCHING CN690 RY1601 POWER FACTOR CONT L690 F1601 DC IN +13V CATHODE CN1602 RELAY DRIVE L1601 L1604 AC SENSE Q1602 ST 5V RECT IC1602...
  • Page 125 P Block TP501 TP502 TP503 IC502 H FB H PIN PWM CONT TP509 TP512 T501 CN506 +12V HV DRV HV OUT IC505 (H/V CONTROL) HD IN D BOARD(1/2) BUFF HV OUT H FB IN1+ DRIVE CN2506 Q513,514 Q520 Q511 H PIN IN1- D525 TP504...
  • Page 126 MA, MB MA, MB MA Block MB Block D9H1 MODEL RY1101 D9H5 MODEL DO/RI D9H5 MODEL CN101 CN104 IC1105 OPTION AUDIO SDI AUDIO RS485 CONT IC1103 TP1103 CN1102(1/2) RS485 REM1 IC112 DO/RI Q102 PARALLEL I/O MISO D OUT CN1103 DO/RI MOSI D IN SLAVE CPU...
  • Page 127 HA, HB, HC HA, HB, HC HA Block HB Block HC Block IC13 IC12 RS422 DRIVE MAIN CPU BUS SHIFT CN201 MA BOARD R IN SW OUT CN105 ROUT RXD1 RXD0 MISO MISO Q201 TP204 TXD0 MOSI MOSI IC201 DOUT TXD1 SCK0 SCLK...
  • Page 128 10-10 10-10 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 129 Section 11 Diagrams Note: [Measuring conditions, voltage and waveform] • Parts marked “ * ” differ according to the model/destination. Refer • A voltage value is the reference value between the measurement to the mount table for each function. point and the earth, when the RGB color bar signal is received •...

  • Page 130: Frame Schematic Diagram

    Frame Frame 11-1. Frame Schematic Diagram CN702 FOCUS 1 TO FBT :MINI FOCUS 2 D9H5 MODEL CN1200 +120V CN601 CN690 CN305 CN701 CN703 +12V H SYNC SEP 1 H SYNC SEP 1 ENCODER 0 NEUTRAL CN1602 S-MICRO S-MICRO S-MICRO +13V +13V VOL OUT ENCODER 0...

  • Page 131: Schematic Diagrams And Printed Wiring Boards

    11-2. Schematic Diagrams and Printed Wiring Boards BX BOARD [BX BOARD] * : B SIDE D101 D102 D201 D202 D301 D302 D401 D402 D501 IC010 IC050 IC501 IC502 IC503 Q101 Q102 Q103 Q201 Q202 Q203 Q301 Q302 Q303 Q401 Q402 Q403 Q404 Q501...

  • Page 132: Bx (1/2)

    BX (1/2) BX (1/2) BX BOARD WAVEFORMS 2.0Vp-p (H) 1.4Vp-p (H) 1.4Vp-p (H) 0.9Vp-p (H) 0.6Vp-p (H) 0.6Vp-p (H) 11-4 11-4 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...

  • Page 133: Bx (2/2)

    BX (2/2) BX (2/2) X25040S (IC503) X DECODE 512 BYTE WRITE STATUS LOGIC ARRAY PROJECT REGISTER LOGIC 32X32 COMMAND DECODE 32X32 CONTROL LOGIC 64X32 WRITE CONTROL TIMING LOGIC Y DECODE HOLD DATA REGISTER 11-5 11-5 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 134 B BOARD * : B SIDE Q460 * B-1 TP300 D1400 Q461 * B-1 TP301 D1401 Q462 TP302 D1402 * C-1 TP303 D1403 Q463 B BOARD Q464 * C-2 TP304 D1404 * B-3 * C-3 Q465 TP310 D1405 * C-1 D2345 * A-5 Q466...
  • Page 135 B (1/4) B (1/4) 11-7 11-7 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 136 B (2/4) B (2/4) 11-8 11-8 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 137 B (3/4) B (3/4) 11-9 11-9 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 138 B (4/4) B (4/4) CXA1211M (IC400, 401) CXA1875AM-T4 (IC4300, 4301, 4302, 4350) IN 2 CONT 2 OUT 2 VCA 2 VCA 1 OPEN COLLECTOR LEVEL LEVEL LATCH CONVERTER CONVERTER IN 1 CONT 1 OUT 1 LEVEL CONVERTER C DECODER POWER RESET LATCH LATCH...
  • Page 139 M62399FP-TE2 (IC4351, 4352) B BOARD WAVEFORMS CS0 CS1 CS2 VREFU2 CHIP SELECT 1.1Vp-p (H) 0.6Vp-p (H) 0.6Vp-p (H) 4.8Vp-p (H) 0.98Vp-p (H) 8BIT 8BIT 8BIT 8BIT UPPER DIGITS UPPER DIGITS UPPER DIGITS UPPER DIGITS SEGMENT R-2R SEGMENT R-2R SEGMENT R-2R SEGMENT R-2R 8BIT LATCH 8BIT LATCH...
  • Page 140 CXA1211M (IC450) IN 2 CONT 2 OUT 2 VCA 2 VCA 1 IN 1 CONT 1 OUT 1 B1 BOARD –A SIDE– SUFFIX: -11 –B SIDE– SUFFIX: -11 11-12 11-12 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 141 B2 BOARD TC4W53FU (IC3908) COMMON OUT IN LOGIC LEVEL CONVERTOR OUT IN –A SIDE– –B SIDE– SUFFIX: -11 SUFFIX: -11 11-13 11-13 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 142 G BOARD * : B-SIDE G BOARD D2501 IC506 D2502 IC507 D2503 IC508 D2504 IC509 D2506 IC510 D2507 IC512 D2508 IC514 D2509 IC515 D2510 IC516 D2511 IC517 D2512 IC519 D2513 * G-2 IC520 D2514 IC522 D2515 * E-6 IC523 * J-2 D2520 * J-5 IC524...
  • Page 143 250V 11-15 11-15 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 144 MCR5102 (IC603) MZ1530 (IC666) INPUT ZERO VOLTAGE CURRENT SENSING SENSING VC-1 VG(H) RESET DETECT X.V. Vc-2 LEVEL PULSE SHIFT FILTER V REF START UP C MOS 5V GATE DRAIN V REF VC-3 LEVEL VC-2 (DRAIN) SHIFT PULSE GEN. VC(L) CATHODE DETECT 13V/8V V REF VC-2...
  • Page 145 C BOARD –A SIDE– –B SIDE– SUFFIX: -11 SUFFIX: -11 C BOARD WAVEFORMS 50Vp-p (H) 33Vp-p (H) 32Vp-p (H) 11-17 11-17 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 146 D BOARD D BOARD *: B SIDE Q1601 D1601 Q1602 D1602 D1603 Q1603 D1604 Q1604 Q1605 D1605 Q1608 D1606 D1607 Q1609 Q1610 D1608 * A-1 Q1611 D1609 D1610 Q1612 D1611 * B-2 Q1613 Q1614 * C-2 D2501 * A-7 * A-6 Q1617 D2504 * A-7...
  • Page 147 D (1/2) D (1/2) 11-19 11-19 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 148 D (2/2) D (2/2) 11-20 11-20 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 149 CXA1875AM-T4 (IC2501, 2502) TDA8172FA (IC2504) TL1451ACPWR (IC1602, 2601, 3601) OUTPUT STAGE SUPPLY FLYBAK GEN FLYBAK GENERATOR OPEN COLLECTOR LEVEL LEVEL LATCH V REF CONVERTER CONVERTER ERROR INVERTING IN 1 AMP 2 LEVEL POWER OUTPUT CONVERTER AMPLIFIER I 2 C DECODER NON INVERT IN 7 POWER ERROR...
  • Page 150 MA BOARD CXD1095BQ (IC112) [MA BOARD] CONTROL * : B SIDE D101 * C-4 * C-4 D102 PX2 52 D103 * B-4 LATCH D104 * B-4 D105 * A-5 * A-5 D106 LATCH D107 * A-5 D108 * A-5 * C-4 LATCH D109 LATCH...
  • Page 151 11-23 11-23 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 152 MB BOARD [MB BOARD] * : B SIDE * A-3 D1100 * A-3 D1101 D1102 * A-4 D1103 * A-5 * C-1 D1104 D1105 * C-1 D1106 * C-1 D1107 * C-1 * C-1 D1108 D1109 * C-1 D1110 * A-2 * A-2 D1111 D1112...
  • Page 153 11-25 11-25 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 154 MAX3100CEE (IC1105, 1108) MB90096PF-127/G-178 (IC1107, 1110) 20 BOUT (SOURCES) DISP 19 ROUT RA/FE 18 GOUT DISPLAY (MASKS) 17 IOUT OUTPUT VSYNC TRANSMIT-DONE (TM) CONTROL 16 VOB1 EVEN DISPLAY DATA-RECEIVED (RM) 15 VOB2 INTERRUPT RESET CONTROL TX-BUFFER REGISTER PARITY (PM) LOGIC DOCKO SERIAL FRAMING ERROR (RAM)/...
  • Page 155 CXA1544M-T6 (IC502) NJM2360AM (TE2) (IC510) 8 CD WIND 7 SI COMPARATOR DRIVE OUT 6 V+ CT OSC T IN PHASE ADJ VREF DUTY PHASE 5 INVIN CONT CONT 1.25V – DELAY COMP DELAY ADJ DUTY ADJ EDGE DETECT COMP CAGC 1 (SELECT) RAGC TL494CNS-E20 (IC503)
  • Page 156 P BOARD [P BOARD] *: B SIDE * C-6 TP501 D501 D502 * B-6 TP502 D503 TP503 TP504 D504 * B-6 TP505 D505 D506 * B-1 TP506 D507 * A-1 TP507 * A-5 TP508 D508 D509 * C-4 TP509 D510 * A-6 TP511 D511...
  • Page 157 11-29 11-29 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 158 HA, HB, HD HA, HB, HD –A SIDE– –A SIDE– SUFFIX: -11 SUFFIX: -11 –B SIDE– –B SIDE– SUFFIX: -11 SUFFIX: -11 –A SIDE– SUFFIX: -11 –B SIDE– SUFFIX: -11 11-30 11-30 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 159 HA, HB HA, HB NJU3716M (IC201, 202, 203, 204) LATCH SHIFT CONTROL REGISTER DATA 11-31 11-31 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 160 AN5265 (IC3201) DC VOLUME AUDIO OUTPUT CONTROL MUTE 11-32 11-32 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 161 YA, YB YA, YB –B SIDE– SUFFIX: -11 –B SIDE– SUFFIX: -11 11-33 11-33 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 162 HC BOARD [HC BOARD] *:B SIDE * A-1 * A-1 * A-1 * A-2 * A-3 * A-2 * B-5 * B-4 * B-3 * B-3 * B-5 IC10 IC11 IC13 IC14 * B-4 IC21 –A SIDE– SUFFIX: -11 –B SIDE– SUFFIX: -11 11-34 11-34...
  • Page 163 LTC490CS8 (IC13) TC74VHC138F (EL) (IC3) TC74VHC244F (EL) (IC12) TC74VHC574F (EL) (IC11) Q OE Q OE Q OE Q OE Q OE Q OE Q OE Q OE D CK D CK D CK D CK D CK D CK D CK D CK 11-35 11-35...
  • Page 164 T BOARD –A SIDE– –B SIDE– SUFFIX: -11 SUFFIX: -11 11-36 11-36 BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A...
  • Page 165 The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.
  • Page 166 English 99IS16033-1 Sony Corporation Printed in Japan Broadcasting & Professional Systems Company 9-929-655-01 ©1999.9...

This manual is also suitable for:

Trinitron bvm-d9h5aTrinitron bvm-d9h5uTrinitron bvm-d9h1eTrinitron bvm-d9h5eTrinitron bvm-d9h1a

Table of Contents