Table of Contents
- 1 Table of Contents
- 2 Environment and Enclosure
- 3 Catalog Number Explanation
- 4 About the Terminals
- 5 Install the Terminal
- 6 USB Ports
- 7 Choose a Power Supply
- 8 Remove the Power Terminal Block
- 9 Connect Power
- 10 Ground the Terminal
- 11 Connect Devices
- 12 Troubleshooting
- 13 Battery Replacement
- 14 Specifications
- 15 Additional Resources
Installation Instructions
PanelView 800 HMI Terminals
Catalog Numbers 2711R-T4T, 2711R-T7T, 2711R-T10T
Topic
About This Publication
This document provides instructions on how to install, wire, ground, and troubleshoot PanelView™ 800
terminals. It does not provide information on how to configure or run applications on the following devices:
2711R-T4T, 2711R-T7T, 2711R-T10T
Industrial automation
Elincom Group
European Union: www.elinco.eu
Russia: www.elinc.ru
Page
3
6
6
9
14
15
16
17
18
19
20
21
23
25
Table of Contents
Related Manuals for Allen-Bradley PanelView 800
Summary of Contents for Allen-Bradley PanelView 800
-
Page 1: Table Of Contents
Installation Instructions PanelView 800 HMI Terminals Catalog Numbers 2711R-T4T, 2711R-T7T, 2711R-T10T Topic Page Environment and Enclosure Catalog Number Explanation About the Terminals Install the Terminal USB Ports Choose a Power Supply Remove the Power Terminal Block Connect Power Ground the Terminal... - Page 2 PanelView 800 HMI Terminals Important User Information Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://www.rockwellautomation.com/literature/) describes some important differences...
-
Page 3: Environment And Enclosure
PanelView 800 HMI Terminals Environment and Enclosure ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating. - Page 4 PanelView 800 HMI Terminals North American Hazardous Location Approval The following information applies when Informations sur l’utilisation de cet équipement operating this equipment in hazardous en environnements dangereux: locations: Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for Les produits marqués "CL I, DIV 2, GP A, B, C, D"...
- Page 5 PanelView 800 HMI Terminals Prevent Electrostatic Discharge ATTENTION: This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines when you handle this equipment: • Touch a grounded object to discharge potential static.
-
Page 6: Catalog Number Explanation
Touch screen 10 in. About the Terminals PanelView 800 terminals are operator interface devices for monitoring and controlling devices attached to a controller. HMI applications are created using Connected Components Workbench software, then downloaded to the terminal. PanelView 800 Terminal – 2711R-T4T... - Page 7 PanelView 800 HMI Terminals PanelView 800 Terminal – 2711R-T7T Item Description Item Description Power status LED Replaceable real-time clock battery Touch display USB host port Mounting slots Diagnostic status indicator RS-422 and RS-485 port Micro-SD (Secure Digital) card slot RS-232 port...
- Page 8 The Power Status LED is red when in screen saver or dimmer mode and green when in normal (operational) mode. The USB device port is not intended for Customer use. Parts List PanelView 800 terminals ship with these items: • Power terminal block •...
-
Page 9: Install The Terminal
PanelView 800 HMI Terminals Install the Terminal Before installing the terminal in a panel, review minimum clearances, panel guidelines, panel cutout dimensions, and product dimensions. Minimum Spacing Plan for adequate space around the terminal, inside the enclosure, for ventilation and cabling. Consider heat produced by other devices in the enclosure. - Page 10 269.0 ±0.5 (10.59 ±0.02) Mount the PanelView 800 Terminal in a Panel Mounting levers secure the PanelView 800 terminal to the panel. ATTENTION: Follow these guidelines when mounting the terminal in a panel. • Disconnect all electrical power from the panel before making the panel cutout.
- Page 11 PanelView 800 HMI Terminals 4. Insert all mounting levers into the mounting slots on the terminal. Slide each lever until the short, flat side of lever touches the surface of the panel. Mounting slots Short, flat side of mounting lever Mounting levers 5.
- Page 12 3.68…4.16 mm (0.145…0.164 in.) 44881 4.19…4.75 mm (0.165…0.187 in.) Remove the PanelView 800 Terminal from the Panel Follow these steps to remove the terminal from the panel. 1. Disconnect power to the terminal. 2. Release the mounting lever by rotating it in the direction indicated, slide it to the bottom of the mounting slot, and remove it.
- Page 13 PanelView 800 HMI Terminals Product Dimensions PanelView 800 Terminal – 2711R-T4T PanelView 800 Terminal – 2711R-T7T Publication 2711R-IN001A-EN-P - January 2015...
-
Page 14: Usb Ports
55 mm (2.17 in.) 51 mm (2.01 in.) USB Ports You can power USB peripherals directly from the PanelView 800 terminal. If the USB peripheral is not powered directly from the PanelView USB port either: • install the USB peripheral in the same enclosure as the PanelView terminal and make sure it is connected to the same ground system. -
Page 15: Choose A Power Supply
100 VA maximum or equivalent. PanelView 800 devices have been tested to operate with 1606-XLP power supplies. To use another power supply, review the criteria in the table. -
Page 16: Remove The Power Terminal Block
PanelView 800 HMI Terminals Remove the Power Terminal Block PanelView 800 terminals ship with a power terminal block installed. You can remove the power terminal block for ease of installation, wiring, and maintenance. ATTENTION: Disconnect all power before installing or replacing components. Failure to disconnect power may result in electrical shock or damage to the terminal. -
Page 17: Connect Power
PanelView 800 HMI Terminals Connect Power All PanelView 800 terminals connect to a 24V DC power source. The table shows the power ratings for each device. Power Ratings Catalog No. Input Voltage Range Power Consumption, Max 2711R-T4T 18…32V DC (24V DC nom) 9 W (0.39 A) -
Page 18: Ground The Terminal
Ground the Terminal PanelView 800 terminals have a functional earth terminal that you must connect to a low-impedance earth ground. The functional earth connection is on the power input terminal block. The negative power terminal is not internally connected to earth ground. -
Page 19: Connect Devices
S (Shield) The RS422/485 port has integrated 120 ohm termination between the R and R- signal pair. This value is compatible with RS422 and RS485 electrical specifications. Additional termination on the PanelView 800 terminal end of communication cables is not required. -
Page 20: Troubleshooting
A terminal that does not receive adequate power could cause unpredictable behavior. Verify the power requirements in the Specifications table. Interpret the LED Indicators at Startup The PanelView 800 terminals have indicators to isolate operating problems. They can be seen through the battery cover on the back of the unit. •... -
Page 21: Battery Replacement
PanelView 800 HMI Terminals Battery Replacement The PanelView 800 terminals contain a lithium battery that is intended to be replaced during the life of the product. The battery provides battery backup for the real-time clock. It is not used for application backup or retention. - Page 22 PanelView 800 HMI Terminals The battery is on the back of the terminals. No special tools are required to remove the battery cover, but a flat-tip screwdriver may be required to remove the battery. Battery cover This equipment is sensitive to electrostatic discharge (ESD) Follow ESD prevention guidelines when handling this equipment.
-
Page 23: Specifications
PanelView 800 HMI Terminals Specifications PanelView 800 - 2711R-T4T, 2711R-T7T, 2711R-T10T Attribute Value 2711R-T4T 2711R-T7T 2711R-T10T Display type Color transmissive TFT active matrix LCD, widescreen format Display size 4 in. 7 in. 10 in. Display area 95 x 53.9 mm 153.6 x 86.6 mm... - Page 24 PanelView 800 HMI Terminals Environmental Specifications Attribute Value Temperature, operating IEC 60068-2-1 (Test Ad, Operating Cold), IEC 60068-2-2 (Test Bd, Operating Dry Heat), IEC 60068-2-14 (Test Nb, Operating Thermal Shock): 0…50 °C (32…122 °F) Temperature, nonoperating IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold),...
-
Page 25: Additional Resources
PanelView 800 HMI Terminals Certifications Certifications (when product is Value marked) c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E322657. UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. - Page 26 PanelView 800 HMI Terminals Notes: Publication 2711R-IN001A-EN-P - January 2015...
- Page 27 PanelView 800 HMI Terminals Notes: Publication 2711R-IN001A-EN-P - January 2015...
- Page 28 Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page. Allen-Bradley, Rockwell Automation, PanelView, and TechConnect are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Publication 2711R-IN001A-EN-P - January 2015 PN-291159 Copyright ©...