Wireless Camera Monitoring System BL-WV10A Model No. This guide will help you install and configure the BL-WV10A Wireless Camera Monitoring System and your Network Cameras (sold separately). Included Items Confirm that the following items are included in the product box.
Setup Overview 1. Insert the batteries in the remote control. 2. Connect the BL-WV10A to the power outlet and to the TV. 3. Use the BL-WV10A’s Basic Setup utility to configure the BL-WV10A. 4. Connect the cameras (and an optional BB-HGW700A Network Camera Management System, if you are using one).
Page 3
Setup Guide Connecting the BL-WV10A There are 2 ways to connect your cameras to the BL-WV10A. Determine which method you will use, and refer to the pages in this manual listed below. Using the BL-WV10A only. Using an optional BB-HGW700A .
Page 4
5. Turn on the BL-WV10A by connecting the DC cord to the unit. • The startup screen appears on the TV screen. 6. Use an Ethernet cable to connect the camera to one of the LAN jacks on the BL-WV10A. • If connecting a BL-C30A, set the camera’s mode switch to [WIRED].
Page 5
Setup Guide Basic Setup After the BL-WV10A starts up for the first time, the [Basic Setup] screen is displayed. For most installations, these parameters do not need to be changed. For information regarding Basic Setup settings, see page xx in the Operating Instructions.
Page 6
When the camera has been configured and registered, “Finished” is displayed next to the camera name (“CAM1”) and the buzzer sounds. 3. To register another camera, connect the camera to one of the LAN jacks of the BL-WV10A, then turn the camera on by connecting it to the power outlet.
Page 7
5. Turn on the BL-WV10A by connecting the DC cord to the unit. • The startup screen appears on the TV screen. 6. Use an Ethernet cable to connect the BB-HGW700A to one of the LAN jacks on the BL-WV10A. 7. Connect the BB-HGW700A to the power outlet.
Page 8
Setup Guide Basic Setup After the BL-WV10A starts up for the first time, the [Basic Setup] screen is displayed. Here you can set the administrator user name and password. For most installations, other parameters do not need to be changed.
Page 9
When the BL-WV10A and BB-HGW700A have been configured, “Finished” is displayed and the buzzer sounds. 2. Use an Ethernet cable to connect the camera to one of the LAN jacks on the BL-WV10A or to one of the LAN jacks on the BB-HGW700A.
Page 10
7. Without connecting the Ethernet cables, turn on the cameras and BB-HGW700A again. 8. To finish, set the BL-WV10A’s mode switch to [NORMAL], disconnect the DC cord from the rear of the unit, reconnect the DC cord, then continue from “Viewing Camera Images” on page xx. If images can be...
Viewing Camera Images To start up the BL-WV10A to view camera images, make sure the mode switch on the rear of the unit is set to [NORMAL] and turn on the BL-WV10A. The startup screen will appear. If the [Date and Time] screen appears, set the date and time, then press [ENTER].
You will return to the previous screen automatically. Using the Included Stand Insert the BL-WV10A into the included stand to use the unit in an upright position. 1. Raise the antenna. Antenna 2. Align the first and last slot as shown an insert the BL-WV10A into the stand.
AC cord plug from the outlet. If there is any trouble Consult an authorized Panasonic Factory Service Center. FCC RF Exposure Warning: • To comply with FCC RF exposure requirements in uncontrolled environment: •...
Page 14
All other trademarks identified herein are the property of their respective owners. Copyright: This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic Communications Co., Ltd.