D-Link DGS-1510 Series Reference Manual page 57
Gigabit ethernet smartpro switch
Hide thumbs
Also See for DGS-1510 Series:
- Web ui reference manual (430 pages) ,
- Getting started manual (65 pages) ,
- Hardware installation manual (64 pages)
Table of Contents
DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
Standard IP Access List:
[SEQUENCE-NUMBER] {permit | deny} {any | host SRC-IP-ADDR | SRC-IP-ADDR SRC-IP-
WILDCARD} [any | host DST-IP-ADDR | DST-IP-ADDR DST-IP-WILDCARD] [time-range
PROFILE-NAME]
no SEQUENCE-NUMBER
Parameters
SEQUENCE-NUMBER
any
host SRC-IP-ADDR
SRC-IP-ADDR SRC-IP-
WILDCARD
host DST-IP-ADDR
DST-IP-ADDR DST-IP-
WILDCARD
precedence PRECEDENCE
dscp DSCP
tos TOS
lt PORT
gt PORT
eq PORT
neq PORT
range MIN-PORT MAX-PORT
TCP-FLAG
fragments
time-range PROFILE-NAME
tcp, udp, igmp, ipinip, gre,
esp, eigrp, ospf, pcp, pim,
vrrp
PROTOCOL-ID
ICMP-TYPE
ICMP-CODE
Specifies the sequence number. The range is from 1 to 65535. The
lower the number is, the higher the priority of the permit/deny rule.
Specifies any source IP address or any destination IP address.
Specifies a specific source host IP address.
Specifies a group of source IP addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The
bit corresponding to the bit value 0 will be checked.
Specifies a specific destination host IP address.
Specifies a group of destination IP addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The
bit corresponding to the bit value 0 will be checked.
(Optional) Specifies that packets can be filtered by precedence
level, as specified by a number from 0 to 7.
(Optional) Specifies the matching DSCP code in IP header. The
range is from 0 to 63, or select the following DSCP name: af11 -
001010, af12 -001100, af13 - 001110, af21 - 010010, af22 -
010100, af23 - 010110, af31 - 011010, af32 - 011100, af33 -
011110, af41 - 100010, af42 - 100100, af43 - 100110, cs1 - 001000,
cs2 - 010000, cs3 - 011000, cs4 - 100000, cs5 - 101000, cs6 -
110000, cs7 - 111000, default - 000000, ef – 101110.
(Optional) Specifies that packets can be filtered by type of service
level, as specified by a number from 0 to 15.
(Optional) Specifies to match if less than the specified port number.
(Optional) Specifies to match if greater than the specified port
number.
(Optional) Specifies to match if equal to the specified port number.
(Optional) Specifies to match if not equal to the specified port
number.
(Optional) Specifies to match if fall within the range of ports.
(Optional) Specifies the TCP flag fields and the specified TCP
header bits called ack (acknowledge), fin (finish), psh (push), rst
(reset), syn (synchronize), or urg (urgent).
(Optional) Specifies the packet fragment's filtering.
(Optional) Specifies the name of the time period profile associated
with the access list delineating its activation period.
Specifies Layer 4 protocols.
(Optional) Specifies the protocol ID. The valid value is from 0 to
255.
(Optional) Specifies the ICMP message type. The valid number for
the message type is from 0 to 255.
(Optional) Specifies the ICMP message code. The valid number for
54
- Quick Links:
- Basic Cli Commands
Hide quick links:
Table of Contents
