KX-TDA0155CE 1 Safety Precautions 1.1. For Service Technicians • Repair service shall be provided in accordance with repair technology information such as service manual so as to pre- vent fires, injury or electric shock, which can be caused by improper repair work.
KX-TDA0155CE 2.1.1. Suggested PbF Solder There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper, (Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi). Please check the manufac turer's specific instructions for the melting points of their products and any precautions for using their product with other materials.
Function Description KX-TDA0155CE is the Cell Station (CS) for TDA and TDE and NCP series. CS converts voice data from PBX to radio signal and transmits to Portable Station (PS). Conversely CS converts radio signal from PS to voice data and transmits to PBX.
Page 7
KX-TDA0155CE 4.2.1.4. FPGA FPGA (IC103) has the following features. (1) ST-BUS I/F, BBIC PCM I/F Extracts voice data from ST-BUS digital data and changes format to BBIC PCM format, then provides it to BBIC(IC100). (2) Superframe detection, delay compensation Detects super frame synchronisation signal from HK bit in the ST-BUS digital data and compensates time difference of delay caused by the different cable length from CSIF card, then provides it to PSYNC pin of BBIC(IC100).
KX-TDA0155CE 4.2.1.6. Power Supply Circuit PAV3.3V, RF2.5V, 3.2V, 1.8V, RF1.8V, 1.5V and 5.25V are generated in CS. 5.5V is output of DC/DC Convertor. Other power supplies are made from 5.25V. PAV3.3V and RF2.5V are the power supply for RF block. 3.2V is the power supply for logic circuit.
KX-TDA0155CE 5 Installation Instructions 5.1. Connecting the Cell Station to the Hybrid IP-PBX KX-TDA0155 connecting to KX-TDA100/KX-TDA200/KX-TDA600/KX-TDE100/KX-TDE200/KX-TDE600 Note The illustration of the PBX is based on the KX-TDE200. Accessories and User-supplied Items for the CS Accessories (included): Screws x 2, Washers x 2...
Page 10
KX-TDA0155CE KX-TDA0155 connecting to KX-NCP500/KX-NCP1000 Note The illustration of the PBX is based on the KX-NCP500. Accessories and User-supplied Items for the CS Accessories (included): Screws x 2, Washers x 2 User-supplied (not included): RJ11 connector Note For details about the DHLC/DLC card, refer to the Installation Manual for your PBX.
KX-TDA0155CE 5.2. Connectiong the CS 1. Connect the cable from CSIF card to the CS. 2. Pass the cable through the groove of the CS (in any direction depending on your preference).
KX-TDA0155CE 6 Test Mode 6.1. Required Equipment 1. Personal Computer with serial port. 2. Servuce Jig cable (PSZZ2CA155EU) 3. TEL cord 4. Power Supply Adaptor (PSZZ1TDA0142) 5. AC Adaptor (KX-TCA1 / KX-A11 / PSLP1434) 6. Maintenance software for PC (PSZZ3TD7896M) 6.2.
KX-TDA0155CE 4. Set communication environment Click “Config” and configure as follows: Click “OK”. Selected items will be stored. 6.3. Command Reference 6.3.1. Select From Command Menu - Example of Operation - 1. Click [test command] tag...
Page 14
KX-TDA0155CE 2. Click [ Command menu ] button and select the command that you want execute. (in case of test command "VDD") 3. Set parameters if necessary.
Page 15
KX-TDA0155CE 4. Click [send] button. Maintenance Window is generated, and transmitted command and parameters are displayed. Then receive data from TDA0155CE is displayed. - Operation of each test command - A) Test Command "VDD control (VDD)" 1. Click [ Command menu ] button.
Page 16
KX-TDA0155CE D) Test Command "RFPI write (RFW)" 1. Click [ Command menu ] button. 2. Point [ RF ]. 3. Click [ RFPI write (RFW) ]. 4. Set ID (5 byte) to the first parameter 5. Click [ Send ] button.
Page 17
KX-TDA0155CE 6.3.2. Input The Command Directly Menu - Example of Operation - 1. Click [test command] tag. 2. Input the command and parameter (if necessary) directly to the [command] box. (Don't set paramter to the [parameter] box. ) (in case of test command "RFC")
Page 18
KX-TDA0155CE 3. Click [send] button. Maintenance Window is generated, and transmitted command and parameters are displayed. Then receive data from TDA0155CE is displayed. note: When you overwrite the command used last time and input a new command, it is no problem though parameter of old command...
KX-TDA0155CE 8 Disassembly and Assembly Instructions 8.1. Disassembly Instructions 1. Remove the five screws (A), and remove the Bottom Cabinet. 2. Remove the Solder on Cable of the Main Board by the Soldering iron. 3. Remove the Main Board from the Top Cabinet.
KX-TDA0155CE 9 Measurements and Adjustments 9.1. Version Check and CSID Writing 9.1.1. Required Equipment 1. (PC)Personal Computer with serial port (Windows 2000/98 or previous version) 2. Power supply adaptor (PSZZ1TDA0142) 3. Service JIG cable (PSZZ2CA155EU) 4. AC Adaptor (KX-TCA1 / KX-A11 / PSLP1434) or Battery Box (PSZZTD142CE) 5.
Page 23
KX-TDA0155CE 9.1.3. Version check Text following “Command:” is the input command for the terminal connected to the CS. Text following “Response:” is the terminal display response data. Confirm the response before proceeding to the next step.If no response is set. shot off power and repeat from the beginning.
KX-TDA0155CE 9.2. Adjustment for Main Part 9.2.1. Required Equipment 1. Tester 2. Frequency counter 3. (PC)Personal Computer with serial port (Windows 2000/98 or previous version) 4. Power supply adaptor (PSZZ1TDA0142) 5. Service JIG cable (PSZZ2CA155EU) 6. AC Adaptor (KX-TCA1 / KX-A11 / PSLP1434) or Battery Box (PSZZTD142CE) 7.
Page 25
KX-TDA0155CE 9.2.3. Adjustment for 1.8V Description of 1.8V calibration process Text following “Command:” is the input command for the terminal connected to the CS. Text following “Response:” is the terminal display response data. Confirm the response before proceeding to the next step.If no response is set. shot off power and repeat from the beginning.
KX-TDA0155CE 9.3. Measurement and Adjustment for RF Part Note: About the software version Update the software to the latest version before performing the RF test. 9.3.1. Required Equipment 1. CMD60 2. (PC) Personal Computer with serial port (Windows2000/98 or previous version with communication software) 3.
Page 27
KX-TDA0155CE 9.3.2.2. RF Test 1. Set the CMD60 to MANUAL TEST. 2. Set the CMD60 TRAFFIC CARRIER to 5. 3. Press ACCEPT RFPI and SETUP CONNECT on the CMD60. 4. Check Power (NTP) : must be +20 to +24dBm 5. Press MODULATION.
Page 28
KX-TDA0155CE serial port setup check next check boxes ASCII Receiving - Append line feeds to incoming line ends Warp lines that exceed terminal width 10. Supply a voltage to the TEL jack from the AC adaptor (KX-TCA1 / KX-A11 / PSLP1434) via power supply adaptor (PSZZ1TDA0142) 9.3.3.2.
Page 29
KX-TDA0155CE 7. Connect the PC to the CS by service JIG cable 8. Start up the PC and start the hyper terminal 9. Set the hyper terminal property as follows serial port setup Port COM1 Bit per second 19200 Data bits...
KX-TDA0155CE 10.2. How To Replace a Flat Package IC Even if you do not have the special tools (for example, a spot heater) to remove the Flat IC, with some solder (large amount), a sol- dering iron and a cutter knife, you can easily remove the ICs that have more than 100 pins.
KX-TDA0155CE 10.3. How to Replace the LLP (Leadless Leadframe Package) IC and IC ground plate 10.3.1. Preparation • PbF (: Pb free) Solder • Soldering Iron Tip Temperature of 700 °F ± 20 °F (370 °C ± 10 °C) Note: We recommend a 30 to 40 Watt soldering iron.
Page 33
KX-TDA0155CE 10.3.5. How to Remove a Solder Bridge (Doesn't apply to IC ground plate.) When a Solder Bridge is found after soldering the bottom of the IC, remove it with a soldering iron.
KX-TDA0155CE 13 Appendix Information of Schematic Diagram Note: 1. DC voltage measurements are taken with an oscilloscope or a tester with a ground. 2. The schematic diagrams and circuit board may be modified at any time with the development of new technology.
KX-TDA0155CE 14 Exploded View and Replacement Parts List 14.1. IC Data 14.1.1. IC100 (CPU/BBIC) Terminal Name I/O setting Pull-up/down Contents of Control Remark Processing VDDIO 3V power supply Digital ground Address bus Address bus AD10 Address bus AD11 AD10 Address bus...
Page 44
KX-TDA0155CE 42 P3[6]/PD6 Not in use (Open) 43 RDN Read Enable 0:Read 44 WRN Write Enable 0:Write 45 MI/READY Pull-up(Built in) Ready(Not in use(Pull up)) 46 SCLK Bus clock (open) 10.368MHz 47 UTX/P0[0] for maintenance 48 URX/P0[1] Pull-up(Built in) for maintenance...
Page 45
KX-TDA0155CE 110 LSR+/REF Not in use (open) 111 LSR-/REF Not in use (open) 112 CIDIN- Not in use (Ground) 113 VREF_HS/CIDOUT Not in use (open) 114 MIC- Pull-down(Built in) Not in use (Ground) 115 VREF- Not in use (Ground) 116 VBUF Voltage reference 1.5V...
Page 46
KX-TDA0155CE 14.1.2. IC103 (FPGA) Terminal Name I/O setting Pull-up/down Contents of Control Remark Processing Digital ground OEP1 Data Enable pulse 1:Data varid OBP2 Data Enable pulse 1:Data varid HW_FH Frame Head. 8kHz 1:Enable Pull-up(Built in) Not in use FPGA Reserved pin...
Page 47
KX-TDA0155CE 49 TMS Not in use Test purpose only 50 NC Not in use No Connect 51 GND Digital ground 52 VPUMP Not in use Test purpose only 53 NCS Not in use No Connect 54 TDO Not in use...
Page 48
KX-TDA0155CE 14.1.3. IC104 (G/A) Terminal Name I/O setting Pull-up/down Contents of Control Remark Processing 3.2V supply Chipselect 0:Select Read Enable 0:Read Write Enable 0:Write WAITN Not in use(pull down) INTN Interrup Request 0:Enable Digital ground CLM5 Not in use(open) CLM4...
Page 49
KX-TDA0155CE 52 ADR3 A[3] Address Bus 53 ADR2 A[2] Address Bus 54 ADR1 A[1] Address Bus 55 ADR0 A[0] Address Bus 56 VDD 3.2V supply 57 DB7 D[7] Data Bus 58 DB6 D[6] Data Bus 59 DB5 D[5] Data Bus...
KX-TDA0155CE 14.4. Replacement Parts List 14.4.2. Accessory and Packing Materials Note: Safety Ref. Part No. Part Name & Description Remarks 1. RTL (Retention Time Limited) PQHE5004Y SCREW The marking (RTL) indicates that the Retention Time is XWG35FJ WASHER limited for this item.
Page 53
KX-TDA0155CE Safety Ref. Part No. Part Name & Description Remarks Safety Ref. Part No. Part Name & Description Remarks D453 B3AAB0000297 DIODE(SI) R259 ERJ3GEY0R00 D470 MA8047 DIODE(SI) R273 ERJ3GEY0R00 D471 MA8047 DIODE(SI) R280 ERJ3GEY0R00 D472 MA8047 DIODE(SI) R284 ERJ3GEY0R00 D900...
Page 54
KX-TDA0155CE Safety Ref. Part No. Part Name & Description Remarks Safety Ref. Part No. Part Name & Description Remarks R496 ERJ3GEYJ103 C243 ECUV1H471JCV 470p R555 ERJ2RKF2050 C244 ECUV1H103KBV 0.01 R556 ERJ2RKF3300 C245 ECUV1H471JCV 470p R687 ERJ2GEJ561 C248 ECUV1H103KBV 0.01 R725...