Hyperband Automatic channel preset Full function remote control 200 preset channels Intellectualized I AV input/output (RCA) jacks DVD input jacks Selectable picture ON timer/OFF timer/Sleep timer Channel scan Channel edit Child lock Hotel lock Game Calendar Main features C-bus control...
Note: This TV set can operate on an AC power of 240V, 50Hz. You must not use a power supply of any other type. When any unusual situation occurs, turn off the power supply at once and remove the plug from the wall outlet.
Page 4
Safety precautions Do not cover the ventilating hole in the cabinet Keep a space of more than 10cm from the walls to the TV set to ensure adequate ventilation. If the power cord or the plug is damaged contact a qualified service department for service.
Identification of Controls Front MENU MENU Back DVD input (VIDEO; Y,Cb,Cr, AUDIO; L/MONO, R) AV1 input (VIDEO, AUDIO; L/MONO, R) S-VIDEO input AV/TV CHANNEL DOWN TV/AV CHANNEL UP AV2 input (VIDEO, AUDIO; L, R) Power Switch Indicator Remote Sensor VOL- VOL+ VOLUME DOWN VOLUME UP...
Identification of Controls Remote control Power on/standby Direct channel select Digit select Sleep timer Program scan Enter into music mode Volume down Open the menu TV/AV GAME ZOOM CALL MUTE SCAN MUSIC TV/VIDEO input select Game playing Picture zoom Recall on-screen display Sound mute Return to previous channel Picture mode select...
Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used. The exact type and position of the aerial will depend upon your particular area. Notes: It is recommended that the 75-ohm coaxial cable be used to eliminate interference and noise which may occur due to radio wave conditions.
Preparing the remote control Installing batteries Open the battery cover. Install two "AA" batteries matching the +/- polarities of the battery to the +/- marks inside the battery compartment. Replace the battery cover. Notes: Do not try to recharge batteries that are not intended to be recharged.
External equipment connections The following describes how to use and connect the TV with other AV equipment (for example, VTR, Video Camera, DVD, Video game, etc.) Please refer to the owner's manual of the equipment to be connected as well. To connect AV input terminals Connect side AV inputs To access the unit connected...
External equipment connections To connect DVD input terminals The figure below shows how to connect the DVD input terminals of the TV set to the DVD Player, Laser Disk Player, etc. The TV set rear To access the unit connected to these jacks, press TV/AV button until YUV appears on the screen. Notes: 1.
TV/AV GAME ZOOM CALL MUTE SCAN MUSIC Power on/off Turning on Press the Power Switch on the TV set. If no picture appears on the screen and the standby indicator lights up, the TV set is in STANDBY mode. Now please follow step 2. In STANDBY mode, press standby ( on the remote controller and the TV set is turned In STANDBY mode, you can also press Channel up/down...
Selecting input signal TV/AV TV/AV GAME ZOOM CALL MUTE SCAN MUSIC Watching AV program This TV set provides AV input terminals for your convenient connection to VCR, DVD or other video equipment. To watch video program from AV inputs, press TV/AV button repeatedly until you see the appropriate input indicator on the screen.
There are two ways to preset channels: to preset channels automatically and to preset channels manually. Below we will describe how to preset the channels by making use of the menu. TV/AV GAME ZOOM CALL MUTE SCAN MUSIC * To exit the menu, press CALL button or repeatedly press MENU button.
If Auto Search can not preset the desired channels, or you want to preset the desired channels one by one with the preferred channel numbers, please make use of SEARCH. TV/AV GAME ZOOM CALL MUTE SCAN MUSIC * To exit the menu, press CALL button or repeatedly press MENU button.
TV/AV GAME ZOOM CALL MUTE SCAN MUSIC * To exit the menu, press CALL button or repeatedly press MENU button. Tuning in To skip unnecessary channel After presetting the channels, you can skip unnecessary channels so that only the channels you want to watch are selected with Program up/down buttons.
TV/AV GAME Direct channel select buttons ZOOM CALL CALL MUTE SCAN MUSIC Channel selection You can select your desired TV program by one of the following methods. Use Direct Channel Select buttons To select one-digit channel: Press 0-9 button directly. Press 0-9 button To select two-digit channel:...
TV/AV GAME ZOOM CALL MUTE SCAN MUSIC * To exit the menu, press CALL button or repeatedly press MENU button. Channel edit You can edit the channel programs in your favourite order. Channel edit Press MENU repeatedly to display Preset menu. Press P+ or P- to select PROG EDIT.
TV/AV GAME ZOOM CALL MUTE SCAN MUSIC * To exit the menu, press CALL button or repeatedly press MENU button. Picture adjustment To select the picture mode You can select the picture quality instantly among three preset modes and one user-set mode. Press button to select the desired picture quality.
TV/AV GAME ZOOM CALL MUTE MUTE SCAN MUSIC Menu control buttons Sound controls Adjusting volume Use Volume up/down button Press V- button, the volume decreases; Press V+ button, the volume increases. Use MUTE button If you want to mute the sound, press MUTE button on the remote.
TV/AV GAME ZOOM CALL MUTE SCAN MUSIC * To exit the menu, press CALL button or repeatedly press MENU button. Timer setting Setting clock time Making use of this function can set the current time for the TV. Press MENU repeatedly to display the Time menu.
TV/AV GAME ZOOM CALL MUTE SCAN MUSIC * To exit the menu, press CALL button or repeatedly press MENU button. Timer setting Setting ON timer/ON program With the ON timer, the TV will automatically turn on to a preset channel at a preset time. In Time menu, press P- or P+ to select ON TIME.
TV/AV GAME ZOOM CALL MUTE SCAN MUSIC * To exit the menu, press CALL button or repeatedly press MENU button. System setup Setting Blue Screen Press MENU repeatedly to display Setup menu. Press P- or P+ to select BLUE SCREEN. Press V+ or V- to turn on/off BLUE SCREEN.
TV/AV GAME ZOOM CALL MUTE SCAN MUSIC The master password to enter into LOCK menu is 4100. Make sure not let children know the password. Now the Child Lock function is activated, the locked channel's screen is blank and a locked icon on the screen.
TV/AV GAME ZOOM Digit buttons CALL MUTE SCAN MUSIC Lock menu control buttons Lock setting This unit provides Hotel Lock function, you can limit sound volume which is especially useful in hotel. Hotel lock setup Use password to enter into LOCK menu.
TV/AV GAME ZOOM CALL MUTE SCAN MUSIC Other functions ZOOM function Making use of zoom function can change the screen's vertical size. Press ZOOM button repeatedly, ZOOM, 16: 9 and 4:3 can be selected cyclically. You can select one of them according to actual need, for example, to view wide screen movie VCD.
Troubleshooting Guide Before calling service personnel, please check the following chart for a possible cause to the trouble you are experiencing. Symptoms Power is not turned on. Poor colour poor tint. Spots appear on the screen. Stripes appear on the screen. Double images or "ghosts".
Troubleshooting Guide Reception disturbances Most types of television interference can be remedied by adjusting the height and position of the VHF/UHF antenna. Outdoor antennas are recommended for best results if not using cable. The most common types of television interference are shown below. If one of these symptoms appear when the TV is connected to a Cable TV system, the disturbance may be caused by the local cable company broadcast.
Power Supply: AC 240V, 50Hz Power Consumption: 150W (Max.) Dimensions (mm): 762 (W) x 580 (H) x 520 (D) Weight (kg): CRT: 68cm TV system & channel range System 2-12 PAL-B/G Colour System: PAL-BG, NTSC (AV) Sound output: 4W + 4W Accessories: Remote control x 1 Note: Design and specifications are subject to change without notice.