Table of Contents
Quick Links
Davey Peristaltic Pump
Operating Instructions
WARNING: Failure to follow these instructions and comply with all applicable
codes may cause serious bodily injury and/or property damage.
The installation of this product should be carried out by a person knowledgable
in swimming pool plumbing requirements following the installation instructions
provided in this manual.
Please pass these instructions on to the operator of this equipment.
AS Series
Installation and
Table of Contents
Related Manuals for Davey AS Series
Summary of Contents for Davey AS Series
-
Page 1: Operating Instructions
Davey Peristaltic Pump AS Series Installation and Operating Instructions WARNING: Failure to follow these instructions and comply with all applicable codes may cause serious bodily injury and/or property damage. The installation of this product should be carried out by a person knowledgable in swimming pool plumbing requirements following the installation instructions provided in this manual. -
Page 2: Table Of Contents
4.2.1 Adjustment of the Set point ...............12 4.3 Operating Principle ..................13 5. Maintenance .......................13 5.1 Replacement of the Peristaltic Tube............13 5.2 Maintenance of the Electrode..............14 5.3 Controller Winterising ..................14 5.4 Probe Winterising ..................14 6. Trouble Shooting ....................15 7. Davey Repair or Replacement Guarantee ............16... -
Page 3: Warnings And Tips
1.2 Risks • After unpacking the pump, make sure that it is completely sound. In case of doubt, do not use the pump and contact Davey •The packing materials (plastic bags, polystyrene, etc.) should be kept out of the reach of children: As they may constitute a potential source of danger •... -
Page 4: Toxic And/Or Dangerous Liquid Dosage
Failure to respect this condition could render the pump unsafe to use • When the Davey AS Series pump is not in use for a substantial period of time, or use is to be discontinued, disconnect the unit from any power... -
Page 5: Pump Description
2. Pump Description The Davey Peristaltic pump is characterised by its ability to measure pH value (between 0 and 14) with its probe placed on the filtration system that analyses the pool water. Depending of the measured value, the pump will inject the required amount of product needed to maintain the balance of the pool water. -
Page 6: Buttons Description
2.2 Buttons Description pH - Fig. 2 1. Press SET to see and adjust the set point. 2. Press CAL allows calibration of the pH level associated to the SET button to change the value of the set point 3. Value/level of pH in water 4. -
Page 7: Installation And Recommendation
• Carefully observe any standards in force in your state, territory or country, as to electrical installation regulations and requirements • The Davey AS Series pump will be in operation only when your filtration pump is running WARNING •... -
Page 8: Accessories Mounting
3.2 Mounting the Pump 3.2.1 Bracket • Use mounting accessories « H » to fix the bracket of the pump • Remove the bracket on the pump by sliding it down • Locate the bracket in the space chosen and mark the holes •... -
Page 9: Mounting Of The Clamp
3.2.2 Mounting of the Probe clamp This assembly is fixed on the pipe Pierce the top wall of the pipe work. work through the clamp: - Ø 8mm for the injection valve - Ø 14 mm for the electrode/pH probe. A nut Next Oring... -
Page 10: Mounting Of The Probe On The Probe Holder
3.2.4 Mounting of the pH Probe into the Probe Holder After removing the protective cap from the probe, you need to insert all the parts as shown in the Fig.9. Once the probe has been constructed as indicated in Fig.9, tighten the probe nut without crimping the probe body. -
Page 11: Commissioning And Operation
• Open the isolation valves, if fitted • Turn on the filtration pump and check that the ON/OFF switch (I/O) of the AS Series Fig. 12 pump is switched to “I” • Carry out the calibration of the probe and repeat the previous actions to put the probe back in place. -
Page 12: Settings
CAL button until the display shows CAL or the cable. flashing then release. The quality of the probe reading is then briefly displayed. The calibration of AS Series is completed; It is now ready to measure the pH of your pool. 4.2 Settings Functions... -
Page 13: Operating Principle
The Davey Peristaltic pump adjusts its dosage in proportion to the demand. It will dose less if the displayed measure is near the set point. In normal operation, the AS Series pump will increase its ‘non operational’ time period proportional to the required dosage demand. That is why the device often has the pump off. -
Page 14: Maintenance Of The Electrode
5.2 Maintenance of the probe Over time, in addition to the normal wear of the probe, according to use and water quality more or less calcareous, measurement will deteriorate. A thin layer of limestone with other elements present in the pool water will deposit on the sensing element of the probe. -
Page 15: Trouble Shooting
- Total alkalinity Alarm Alr Err - TH (hardness) - pH The dosing pump will restart as soon as the pH reading If trouble persists, please contact Davey or your nearest Davey Dealer for assistance. -
Page 16: Davey Repair Or Replacement Guarantee
Davey Dealer from which you purchased the Davey product. Alternatively you can send a written letter to Davey at the addresses listed below. On receipt of your claim, Davey will seek to resolve your difficulties or, if the product is faulty or defective, advise you on how to have your Davey product repaired, obtain a replacement or a refund.