Available languages
Available languages
Quick Links
Installation Instructions
27” & 30” Electric Built-In Wall Ovens
Questions?
Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com
In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca
• Note to Consumer – Keep these instructions
BEFORE YOU BEGIN
for future reference.
Read these instructions completely and
• Skill level – Installation of this appliance
carefully.
requires a qualified installer or electrician.
•
Save these instructions
• Proper installation is the responsibility
for local inspector’s use.
of the installer.
•
• Product failure due to improper installation
Observe all governing
is not covered under Warranty.
codes and ordinances.
• Note to Installer – Be sure to leave these
• Product is for indoor use only.
instructions with Consumer.
ATTENTION INSTALLER:
All electric wall ovens must be hard-wired (direct-wired) into an
approved junction box. A plug and receptacle is NOT permitted on these products.
FOR YOUR SAFETY:
WARNING:
Before beginning the installation, switch power off at the service panel and
lock the service disconnecting means to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,
to the service panel.
Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure.
Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,
stand or hang on the oven door.
Make sure the wall coverings, counters and cabinets around the oven can withstand the heat
(up to 200°F [93.3°C]) generated by the oven.
MATERIALS YOU MAY NEED
TOOLS YOU MAY NEED
Junction Box
1/8” Drill Bit and Electric or Hand Drill
Wire Nuts
Phillips Screwdriver
Strain Relief Clamp for 1/2” Conduit
Wire Strippers
36” (91 cm) of String
7/16” Nut Driver
T20 Screwdriver (hinge bracket)
1/4” Nut Driver
1
REMOVE PACKAGING MATERIALS
Failure to remove packaging materials could result in damage to the appliance. Remove all packing
parts from oven, racks and heating elements. Remove protective film and labels on the outer door
and control panel. Also, remove plastic on trims and panel, all tape around the oven and any shipping
screws securing the oven to the base pad. Open oven door and remove literature pack and oven
racks. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation
process. The trim is wrapped separately and taped to the top of the unit. Remove pedestal rails from
seperate box and set aside (30” Double Wall Ovens Only).
2 C
CUTOUT FOR DOUBLE OVENS (2 THERMAL OVENS)
NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim
both sides equally to establish the cutout width.
H
B
Junction
Box
Location
(junction
box may
be located
in adjacent
cabinet)
F
D
C
J
G
E
Cutout Depth
K
23-1/2”
(59.7 cm) Min.
A
Dim.
Description
27” Double Oven
30” Double Oven with
30” Double Oven
Pedestal
without Pedestal
A
Cabinet Width
27” (68.6 cm)
30” (76.2 cm)
30” (76.2 cm)
28
” (72.4 cm) min.
28
” (72.4 cm) min.
1 2
1 2
B
Cutout Width
25” (63.5 cm) min.
28
” (72.7 cm) max.
28
” (72.7 cm) max.
5 8
5 8
25
” (64.1 cm) max.
1 4
51
” (131.6 cm) min.
13 16
C
Cutout Height
49
” (126.2 cm) min.
50 ¼” (127.64cm)
11 16
51
” (131.9 cm) max.
15 16
50
” (127.3 cm) max.
1 8
D
Overlap of Oven
1” (2.5 cm)
” (1.75 cm)
” (1.75 cm)
11 16
11 16
Over Side Edges
of Cutout
E
Clearance to
23” (58.4 cm) min.
23” (58.4 cm) min.
23” (58.4 cm) min.
Adjacent Corners,
Drawers, Walls, etc.,
When Door Is Open
F
Overlap of Oven
1” (2.5 cm) min.
1” (2.5 cm) min.
1” (2.5 cm) min.
Top of Cutout
(1
” (3.2 cm) for PT9550)
(1
” (3.2 cm) for PT9550)
1 4
1 4
G
Overlap of Oven
1” (2.5 cm) min.
1
” (3.2 cm)
1
” (3.2 cm)
1 4
1 4
Bottom of Cutout
H
Junction Box
8
” (22.2 cm) max.
9
” (24.1 cm) max.
9
” (24.1 cm) max.
3 4
1 2
1 2
Location
right side only
right side only
right side only
J
Height to Bottom
44” (111.8 cm)
47” (119.4 cm)
47” (119.4 cm)
of Junction Box
K
Recommended
13
” (33.7 cm)
12” (30.5 cm)
12” (30.5 cm)
1 4
Cutout Location
from Floor
Continue to Section 3 for DWO with Pedestal. Otherwise, continue to Section 4.
DESIGN INFORMATION
SINGLE OVEN INSTALLATIONS
The single oven may be installed in a cabinet alone or above a warming drawer. The single oven may also
be installed below a countertop or below specified cooktops. See the label on top of the oven for approved
models.
DOUBLE OVEN INSTALLATIONS
A double oven may be installed in a cabinet alone or above a warming drawer. See the label on top of the
oven for approved models.
IMPORTANT: Always refer to individual installation instructions packed with each product for specific
requirements.
2
PREPARE THE OPENING
NOTE: If the cabinet does not have a solid bottom, two
2" x 4" (5 cm x 10 cm)
or Equivalent Runners Level
braces or runners must be installed to support the weight
with Bottom of Cutout
of the oven. For single ovens, the runners and braces
and Flush with Sides of Cutout
must support 200 lbs (91 kg). For double ovens, the
runners and braces must support 375 lbs. (170 kg).
C
NOTE: If marks, blemishes or the cutout opening are
L
visible above the installed oven, it may be necessary to
add wood shims under the runners and front trim until
the marks or opening are covered.
NOTE: If the cabinet does not have a front frame and
the sides are less than ¾” (1.9 cm) thick, shim both sides
equally to establish the cutout width.
Suitable
Bracing
to Support
2 D
CUTOUT FOR DOUBLE OVENS (with Upper Microwave Oven)
NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim
both sides equally to establish the cutout width.
Dim.
Description
27” Oven
30” Oven
with Microwave
with Microwave
A
Cabinet Width
27” (68.6 cm)
30” (76.2 cm)
28
” (72.4 cm) min.
1 2
B
Cutout Width
25” (63.5 cm) min.
28
” (72.7 cm) max.
5 8
25
” (64.1 cm) max.
1 4
42
” (107.2 cm) min.
3 16
C
Cutout Height
41
” (104.5 cm) min.
1 8
42
” (107.3 cm) max.
1 4
41
” (104.8 cm) max.
1 4
D
Overlap of Oven Over Side Edges
1” (2.5 cm)
” (1.75 cm)
11 16
of Cutout
E
Clearance to Adjacent Corners,
23” (58.4 cm) min.
23” (58.4 cm)
Drawers, Walls, etc., When Door
Is Open
F
Overlap of Oven Top of Cutout
1” (2.5 cm) min.
1” (2.5 cm) min.
G
Overlap of Oven Bottom of Cutout
1” (2.5 cm) min.
1
” (3.2 cm)
1 4
H
Junction Box Location
8
” (22.2 cm) max.
9
” (24.1 cm) max.
3 4
1 2
right side only
right side only
Continue to Section 4.
2 A
CUTOUT FOR SINGLE OVENS IN WALL CABINET
NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim
both sides equally to establish the cutout width.
H
These ovens
are not
Junction
B
approved for
Box
Location
stackable
(junction
installations.
box may
be located
in adjacent
cabinet)
F
Opening
22” (55.9
D
Between Inside
C
cm) Min. to
Walls Must be
Bottom of
at Least 28-1/2”
G
Junction
(72.4 cm) Wide
Box
E
Cutout Depth
23-1/2”
(59.7 cm) Min.
Recommended
Cutout Location
Note: Allow
from Floor
1/4” (0.64 cm)
32-1/2” (82.6 cm)
clearances
from side
edges of oven
door.
Side-by-Side Installations
Install two ovens in separate cutouts.
A
Center Line
Center Line
30.5” (77.5 cm)
30” models
27” (68.58 cm)
27” models
Cutout –
Cutout –
observe all
observe all
dimensions and
dimensions and
requirements.
requirements.
2” (5.1 cm) Min.
Dimension
Dimension Description
27” Single Oven
30” Single Oven
A
Cabinet Width
27” (68.6 cm)
30” (76.2 cm)
B
Cutout Width
25” (63.5 cm) min.
28
” (72.4 cm) min.
1 2
25
” (64.1 cm) max.
28
” (72.7 cm) max.
1 4
5 8
C
Cutout Height
27
” (70.2 cm) min.
27
” (69.2 cm) min.
5 8
1 4
28
” (71.4 cm) max.
27
” (69.4 cm) max.
1 8
5 16
D
Overlap of Oven Over
1” (2.5 cm)
” (1.75 cm)
11 16
Side Edges of Cutout
E
Clearance to
23” (58.4 cm) min.
23” (58.4 cm) min.
Adjacent Corners,
Drawers, Walls, etc.,
When Door Is Open
F
Overlap of Oven
1” (2.5 cm) min.
1” (2.5 cm) min.
Top of Cutout
(1
” (3.2 cm) for PT9050)
1 4
G
Overlap of Oven
1” (2.5 cm) min.
1
” (3.2 cm)
1 4
Bottom of Cutout
H
Junction Box Location
8
” (22.2 cm) max.
9
” (24.1 cm) max.
3 4
1 2
right side only
right side only
2 E
SECURING UPPER MICROWAVE/ADVANTIUM OVEN TO CABINET
For double oven with microwave or Advantium upper ovens. Secure a wooden cleat to side of cabinet
so that the upper oven can be secured to the cleat with provided screws
27” Cabinet requirements
1.5”
• No shims (or cleats) required when cabinet is in minimum
width condition.
6.375”
• If cabinet is at maximum width condition, add wood
3.0”
shims to bring cabinet to minimum condition.
Wood Cleats
30” Cabinet requirements
• No shims (or cleats) required when cabinet is in minimum
27.5”
width condition.
• If cabinet is at maximum width condition, fix the wood
cleats as shown in illustration.
Cleat locations on 30” cabinet
with maximum cutout condition
2 F
CUTOUT FOR INSTALLATION OVER A WARMING DRAWER
NOTE: Install the oven only with specific models listed on the label located on top of the oven.
NOTE: Additional clearances between cutouts may be required. Check to be sure the oven supports
above the Warming Drawer location do not obstruct the required interior depth and height.
When installing a Warming Drawer below a single or double oven, a separate 120V, 60 HZ, properly
grounded receptacle must be installed. Refer to installation instructions packed with
the Warming Drawer for specific installation requirements.
Anti-Tip Block Against
Rear Wall Per Warming
Drawer Requirement
2" (5.1 cm)
Min.
Per Warming
Drawer
Requirement
Continue to Section 4
2 B
CUTOUT FOR SINGLE OVENS – UNDER COUNTER
NOTE: These ovens are only approved to be installed under the specific models as labeled on the unit.
Side-by-Side Installations
Install two ovens in separate cutouts.
Center Line
Center Line
30.5” (77.5 cm) 30” models
27” (68.58 cm) 27” models
Cooktop
Cutout – observe
Cutout – observe
all dimensions and
all dimensions and
requirements.
requirements.
2” (5.1 cm) Min.
NOTE: One cooktop may be centered over either oven in
the side-by-side installation.
Dimension
Dimension Description
27” Single Oven
30” Single Oven
A
Cabinet Width
25” (63.5 cm) min.
28
” (72.4 cm) min.
1 2
25
” (64.1 cm) max.
28
” (72.7 cm) max.
1 4
5 8
B
Cutout Height
27
” (70.2 cm) min.
27
” (69.2 cm) min.
5 8
1 4
28
” (71.4 cm) max.
27
” (69.4 cm) max.
1 8
5 16
C
Unit Overlap Top
1” (2.5 cm)
1” (2.5 cm)
(1
” (3.2 cm) for PT9050)
1 4
D
Unit Overlap Bottom
1” (2.5 cm)
1
” (3.2 cm)
1 4
E
Unit Overlap Side Edges
1” (2.5 cm)
” (1.75 cm)
11 16
F
Junction Box Location
8
” (22.2 cm) max.
9
” (24.1 cm) max.
3 4
1 2
right side only
right side only
Continue to Section 4.
3
PEDESTAL RAIL INSTALLATION (30” DOUBLE OVENS ONLY)
A. Place one pedestal rail on each cabinet runner or centered on opposite side of solid cabinet bottom
flush with side of cabinet opening. Locate each rail so that front of rail is behind front cabinet
opening.
B. Drill pilot holes and attach rails to runner or bottom of cabinet with provided hardware.
4 A
DOOR REMOVAL (RECOMMENDED)
NOTE: Door removal is not a requirement for installation of the product but is an added convenience.
To remove the door:
A. Open the oven door as far as it will go.
Hinge Bracket
B. Remove hinge bracket from front frame and set aside. The hinge bracket must
be replaced for proper door functionality when door is reinstalled.
C. Push both hinge locks down toward the door frame to the unlocked position.
This may require a flat-blade screwdriver. DO NOT LIFT THE DOOR BY THE
HANDLE!
D. Place hands on both sides of the door and close the oven door to the removal
position (approximately 1”–2” [2.5 cm–5.1 cm] from the closed position).
E. Lift the door up and out until the hinge arms clear the slots.
NOTE: The oven door is very heavy. Be sure
you have a firm grip before lifting the oven door off the hinges. Use caution
once the door is removed. Do not lay the door on its handle.
This could cause dents or scratches.
Hinge Unlocked Position
Hinge Slot
Hinge Clears Slot
Hinge Arm
Related Manuals for GE JT3800SHSS
Summary of Contents for GE JT3800SHSS
- Page 1 Questions? be installed below a countertop or below specified cooktops. See the label on top of the oven for approved Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com models. These ovens In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca...
- Page 2 The current-carrying capacity of the conductor is governed by the wire gauge and the from the front). available for your model. To check availability or order parts, call 1.800.GE.CARES. temperature rating of the insulation around the wire.
- Page 3 ¿Preguntas? puede instalarse debajo de un mostrador de encimera o debajo de las estufas especificadas. Vea la Llame al 1.800.GE.CARES (1.800.432.2737) o visite GEAppliances.com etiqueta de la parte superior del horno para consultar los modelos aprobados. Estos hornos En Canadá, llame al 1.800.561.3344 o visite www.GEAppliances.ca.
- Page 4 Para verificar la disponibilidad o solicitar piezas, llame al 1.800.GE.CARES. horno dentro el conducto quede sobre el horno de temperatura de la aislación alrededor del cable.