CONTENTS Page Page 1 PICTORIAL WIRING DIAGRAM 4.4. FAN MOTOR UNIT 2 EXPLODED VIEW (MC-E3003, MC-E3001) 4.5. CARBON BRUSHES 3 PARTS LIST (MC-E3003, MC-E3001) 4.6. PC board w/component, ON/OFF Switch, Fuse unit and 4 REPLACEMENT OF MAIN PARTS Mains lead (power cord) 4.1.
MC-E3001 / MC-E3003 3 PARTS LIST (MC-E3003, MC-E3001) Ref. No. Part No. Part Name & Description Remarks AMC95B-XB0WE Handle unit MC-E3001 UK (AMC95B-XB0W) AMC95B-XB0AE Handle unit MC-E3003 UK (AMC95B-XB0A) AMC95B-XB0AQ Handle unit MC-E3003 Germany, Italy, Spain AMC33Z-XD008 Warning label MC-E3001, E3003 UK...
Page 5
MC-E3001 / MC-E3003 Ref. No. Part No. Part Name & Description Remarks AMC31A-XB04E Furniture guard AMC25S-XD00E Plastic holder AMC90S-XB00E Idler pulley AMC68A-XD00E Screw AMC47A-XB04E Pedal left/handle release AMC51A-XB00E Pedal shaft AMC58A-XB00E Pedal spring right AMC54R-XB04E End plate AMC06R-XD00E Pipe felt...
MC-E3001 / MC-E3003 4 REPLACEMENT OF MAIN PARTS IMPORTANT: Before replacing any part always DISCONNECT THE CLEANER FROM THE ELECTRICITY SUPPLY. 4.1. BELT (Beater bar belt) , BELT B (Motor shaft belt) 1. Loosen 5 screws from the base plate (Floor nozzle lower 3.
MC-E3001 / MC-E3003 4.2. BEATER BAR UNIT 1. Remove the base plate (floor nozzle lower unit). 2. Remove the beater bar unit from the floor nozzle upper unit. (Fig. 4) 3. Replace the ber unit with a new and place the belt around the beater bar unit.
MC-E3001 / MC-E3003 4.4. FAN MOTOR UNIT 1. As described in paragraph 4.3 of "IDLER PULLEY UNlT", 4. Turn the vacuum cleaner over and remove 4 screws from remove the base plate (floor nozzle lower unit), pedal, and Moter case and take it out. (Fig.9) idler pulley, and belt B, belt.
MC-E3001 / MC-E3003 8. Re-install the motor and reassemble motor case and remaining parts in the reverse order. a. Take out the motor and detach the motor support rubber (rear) and cushion plate (Fig. 10). NOTE: Make sure the lead wires are correctly positioned to avoid pinching them between parts.
MC-E3001 / MC-E3003 4.6. PC board w/component, ON/OFF Switch, Fuse unit and Mains lead (power cord) 1. Loosen two screws from the switch cover unit and take it 5. Connect the lead wires according to the schematic diagram out.(Fig. 12) and re-install switch cover refastening the screws.
MC-E3001 / MC-E3003 4.7. ON/OFF SWITCH 1. Remove the switch cover as explained previously in paragraph "PC board w/component, ON/OFF Switch, Fuse unit and Mains lead (power cord)" (4.6.1.). 2. Remove the Seal Packing A. 3. Disconnect the two lead wires (provided with quickterminal) from the ON/OFF switch terminals.
MC-E3001 / MC-E3003 6 PACKING INSTRUCTIONS Ref. No. Part No. Part Name & Description Remarks AMC01Z-XB00E Operating Instructions MC-E3001,E3003 Language; English AMC01Z-XB00Q Operating Instructions MC-E3003 Language, English, Deutsch, Espanol, Italiano AMC69Z-XB00E Cushion A AMC70Z-XB00E Cushion B AMC0TZ-XB00E Cushion C AMC61Z-XA00E...