Quick Links
TOCR02
2 PART MICRO MOTION
SENSOR W/IR REMOTE
CONTROLLER
Power Circuit Part
PIR Motion Sensor
INTRODUCTION
The use of occupancy detectors in commercial and
industrial applications can significantly reduce energy
usage reducing both energy costs and helping the
environment.
The Titan 360 degrees MICROSENSITIVE 2 PART
flush mount OCCUPANCY DETECTOR uses passive
infrared sensors (PIR) which react to changes in
temperature emitted by the slight motion of persons or
objects passing through its detection area. The PIR
sensor automatically operates the connected load
when an area is occupied. After a preset time on
non-activation (when an area is vacated) the load will
be switched off. In addition the built in photocell takes
natural light (daylight) into account when determining
its activation..
It also incorporates lux memory feature which means
the sensor is able to record and memorize the lux
level when the internal connected light fixture is turned
on by the Micro Motion Sensor. However, once the
natural light lux level is higher than that of the internal
artificial light even if the movement still exists, the
sensor will switch off the internal light fixture thus
saving energy.
The product also incorporates a 2 part structure
allowing the initial installation to be made and the
detector removed to avoid damage during painting,
maintenance etc.
The product is also supplied with a two channel Infra
Red remote control for remote operation.
Note: Read this entire manual before you start to
install the system.
SAFETY PRECAUTIONS
Be sure to switch off power source before
installing.
Make sure that the power wiring comes from
circuit with an external 16A miniature circuit
breaker for the short circuit protection or a
suitable fuse.
The unit is designed to be mounted on the
ceiling.
(FIGURE 1)
The installation of this device should be made by
a qualified electrician.
CHOOSING A MOUNTING LOCATION
Avoid aiming the motion sensor at heating vents,
air conditioners or objects which may change
temperature rapidly.
Prior to mounting the light fixture, remember to
position the motion sensor so that a moving
object cuts "across" its beams, not directly
towards them." (FIGURE 2)
Note: Micro motion detection can be made within
a radius of 3m around the sensor; regular motion
detection can be made within a radius of 6m
around the sensor.
INSTALLATION
A drill and a screwdriver are needed for installation.
Select a location for the unit based on the coverage
angles shown in FIGURE 3.
1
FIGURE 1
FIGURE 2
Summary of Contents for Phase TOCR02
- Page 1 SAFETY PRECAUTIONS TOCR02 Be sure to switch off power source before installing. Make sure that the power wiring comes from 2 PART MICRO MOTION circuit with an external 16A miniature circuit SENSOR W/IR REMOTE breaker for the short circuit protection or a suitable fuse.
-
Page 2: Wiring Instruction
FIGURE 3 WIRING INSTRUCTION (1) Switch off the power source or wall switch. Using a flat blade screwdriver to detach the PIR motion sensor and power circuit part. (FIGURE FIGURE 5b Note: A pulse switch (S2,S4) is connectable to the unit, enabling manual operation. -
Page 3: Loading The Battery
period, the light turns on continuously. After one minute is expired, the light will turn off. Walk through the detection area, the light will turn E253R IR Remote Controller on continuously. If and when movement is ceased, the light will be on for one second before turning off. -
Page 4: Operation
(3) OFF By pressing “Off” button to deactivate the light from illumination. User can also set the motion sensor back to Auto operation by pressing “Auto” button on the IR Remote FIGURE 12 Controller. OPERATION (4) MANUAL OPERATION By using IR Remote Controller to your NL5703, you By using pulse switch to manually control the can easily select three modes of operation: automatic, connected light fixture to be turned on or off. - Page 5 Warning: Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.