Table of Contents
Quick Links
Table of Contents
Related Manuals for Idis DirectIP DH-2010P
Summary of Contents for Idis DirectIP DH-2010P
- Page 1 DirectIP™ PoE Switch Operation Manual DH-2010P DH-2018P Powered by...
-
Page 2: Safety Symbols
Before reading this manual This operation manual contains basic instruction on installing and using DirectIP™ PoE Switch, an IDIS product. Users who are using this product for the first time, as well as users with experience using comparable products, must read this operation manual carefully before use and heed to the warnings and precautions contained herein while using the product. -
Page 3: Fcc Compliance Statement
FCC Compliance Statement THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. -
Page 4: Safety Precautions
Safety Precautions Safety Precautions Information contained in this section of the manual serve to prevent accidents and property damage through proper use of the product. Please read the following instructions carefully and follow them at all times. Warning Failure to comply can lead to severe injury or even death. Installation Make sure to turn off the product before installing it and to use a dedicated power outlet. - Page 5 Safety Precautions Power Voltage fluctuation of the power supply must be within 10% of the voltage rating, and the power outlet must be grounded. Do not plug in electrical appliances such as a hair dryer, iron, and refrigerator into the same power outlet as the product. ●...
- Page 6 Safety Precautions Installation Do not set up the product in an area that is exposed or susceptible to strong magnetism, radio waves, and/or impact and avoid setting up the product in the vicinity of wireless transmission devices such as a radio or a television. ●...
-
Page 7: Table Of Contents
Table of Contents Part 1 - Introduction Product Features Accessories Overview Front Panel Rear Panel Part 2 - Installation Tools for Installation Mounting to a Rack DH-2018P only) Installation Port Connection DirectIP™ NVR Connection DirectIP™ Camera Connection Cascading Port Connection Warnings and Tips Part 3 - Miscellaneous Troubleshooting Specifications... -
Page 8: Part 1 - Introduction
Part 1 Introduction Product Features This multi-port, DirectIP™-based, and IEEE 802.3af and IEEE 802.3at Power over Ethernet-enabled layer2 fast Ethernet PoE Switch offers the following features: ● DirectIP™ – Automatic network IP configuration – Individual port data transmission to DirectIP™ NVR (Network Video Recorder) ●... - Page 9 This PoE switch is able to provide data and power at the same time to the connected network cameras through Ethernet cables by using PoE-enabled ports. It does not need a seperate power outlet for each network camera and it will reduce the installation costs. This PoE switch provides intelligent services such as QoS, security, ACL (Access Control List), and multicast management to ensure stable network communications and to establish high-performance network.
-
Page 10: Accessories
Part 1 - Introduction Accessories Upon unpackaging the product, check the contents inside to ensure that all the following accessories are included. ● DH-2010P/2018P ● Power Cable ● Installation Manual ● Rack Mount Brackets: 2EA (DH-2018P only) ● Screws (6EA for DH-2018P only) Overview Front Panel DH-2010P... - Page 11 Part 1 - Introduction 1 RJ-45 Service Ports These are PoE-enabled RJ-45 ports. Connect a network camera to one of these ports. Model Port Number DH-2010P 1 - 8 DH-2018P 1 - 16 • PoE-supported network cameras will receive power over the signal line, without the use of an external power source.
- Page 12 Part 1 - Introduction LED Status Indications Mode Status Color Description Amber Normal network connection at 10/100Mbps Data transmission over the network in progress at Blinking Amber (Link/Activity) 10/100Mbps No network connection or a problem with the connection Connected and transmits power over the network normally to Green an IEEE 802.3af PoE-supported network camera Not connected to a PoE-supported network camera...
- Page 13 Part 1 - Introduction LED Status Indications Mode Status Color Description Amber Normal network connection at 10/100/1000Mbps Data transmission over the network in progress at Blinking Amber (Link/Activity) 10/100/1000Mbps No network connection or a problem with the connection Green Normal network connection at 1000Mbps SPD (Speed) No network connection or a problem with the connection 9 Reset Switch...
-
Page 14: Rear Panel
Part 1 - Introduction Rear Panel DH-2010P DH-2018P Power Connector Vent 1 Power Connector Connect the power cable to this connector. This product does not feature a separate power on/off button and will turn on the moment power is supplied. • Organize the power cable so that it will not cause people to trip over or become damaged from chairs, cabinets, desks, and other objects in the vicinity. -
Page 15: Part 2 - Installation
Part 2 - Installation Tools for Installation Check the following accessories. You will need more tools beside the accessories which are not provided. ● DH-2010P/2018P ● Power Cable ● Installation Manual Tools for mounting to a rack ( DH-2018P only) ●... -
Page 16: Installation
Part 2 - Installation Installation Place the product in a even and safe place, and prepare for a regular headed screwdriver of medium size ( 0.6 cm/0.24 inch).. Screw brackets to the two sides (3 points for each) of the front panel by using the provided screws and the prepared regular headed screwdriver of medium size. -
Page 17: Port Connection
Part 2 - Installation Port Connection DirectIP™ NVR Connection Connect the DirectIP™ NVR's VIDEO IN/Ext. port to the system's RJ-45 uplink port using a UTP cable. Check the RJ-45 uplink port SPD LED's status and verify that a normal connection has been established. -
Page 18: Directip™ Camera Connection
Part 2 - Installation DirectIP™ Camera Connection Connect the system's RJ-45 service port to the network camera's RJ-45 port using a UTP cable. Check the RJ-45 service port LED's status and verify that a normal connection has been established. PoE cameras connected to RJ-45 service ports can receive power through the UTP cable. -
Page 19: Cascading
Cascading Connect the RJ-45 uplink ports of system 1 and system 2 using a UTP cable. Check the RJ-45 uplink port SPD LED's status and verify that a normal connection has been established between the two products. If the PoE switch is not connected to network connection at 1000Mbps, the network bandwidth may not be enough, and the NVR may not record video normally. -
Page 20: Part 3 - Miscellaneous
Part 3 - Miscellaneous Troubleshooting Problem Check ● Check the power cable. Power LED will not turn on. ● Check the power supply status to the outlet the power cable is connected to. The system shuts down shortly after Check power connection components for electric powering on. -
Page 21: Specifications
Part 3 - Miscellaneous Specifications Model DH-2010P DH-2018P Embedded MIPS System Memory 256MB SDRAM, 32M Flash Switching Capacity 5.6Gbps 7.2Gbps 8 RJ-45 Connectors 16 RJ-45 Connectors Copper Service Port (10/100BASE-T) (10/100BASE-T) Copper Uplink Port 2 RJ-45 Connectors (10/100/1000BASE-T) Rated Input AC100-240V, 50/60Hz AC100-240V, 50/60Hz Power Consumption... - Page 22 IDIS Co., Ltd. For more information, please visit at www.idisglobal.com...