1. Manuals
  2. Brands
  3. Tamerica Manuals
  4. Laminator
  5. TCC-2700
  6. Operating instructions manual

Tamerica TCC 2700 Operating Instructions Manual

Hide thumbs Also See for TCC 2700:

Quick Links

See also: Operating Instructions
TCC 2700 Laminating Machine
TCC 2700 Laminating Machine
TCC 2700 Laminating Machine
Operating Instructions
Operating Instructions
Operating Instructions
Remove machine from carton and place on a stable surface.
Remove machine from plastic bag
Remove bubble-wrap from mandrills
loading

Related Manuals for Tamerica TCC 2700

Summary of Contents for Tamerica TCC 2700

  • Page 1 TCC 2700 Laminating Machine TCC 2700 Laminating Machine TCC 2700 Laminating Machine Operating Instructions Operating Instructions Operating Instructions Remove machine from carton and place on a stable surface. Remove machine from plastic bag Remove bubble-wrap from mandrills...
  • Page 2 TCC 2700 Laminating Machine TCC 2700 Laminating Machine TCC 2700 Laminating Machine Upper mandrill inside the laminating roll Upper heat roller Lower heat roller Lower mandrill inside laminating roll Operating Panel...
  • Page 3 Laminating roll Laminating roll Lower Mandrill Upper Mandrill...
  • Page 4 Insert upper and lower mandrills into core of the film Line up film with appropriate notches on mandrill (25” film lines up with notch that reads “25”” and so forth)
  • Page 5 After inserting the upper and lower mandrills into the core of the film, it should look like the pictures shown below Upper Mandrill inside the laminating roll Lower Mandrill inside the laminating roll...
  • Page 6 How to thread the laminating film How to thread the laminating film How to thread the laminating film laminating roll shiny side Upper mandrill dull side UPPER HEAT ROLLER Threading Bars LOWER HEAT ROLLER laminating roll dull side Lower mandrill shiny side...
  • Page 7 Threading the upper laminating roll Threading the upper laminating roll Threading the upper laminating roll Pass film over the first threading bar...
  • Page 8 Threading the upper laminating roll Threading the upper laminating roll Threading the upper laminating roll Pull film towards front and over the second threading bar...
  • Page 9 Threading the lower laminating roll Threading the lower laminating roll Threading the lower laminating roll Pass film over stable support rod...
  • Page 10 Threading the lower laminating roll Threading the lower laminating roll Threading the lower laminating roll Pass film under and back over the lower threading bar...
  • Page 11 Threading the lower laminating roll Threading the lower laminating roll Threading the lower laminating roll Pull through and over the upper threading bar...
  • Page 12 Both ends of film should meet at heated rollers...
  • Page 13 Switching on the machine and setting Switching on the machine and setting Switching on the machine and setting Switch on the machine Set speed to “1”...

  • Page 14: Setting Up The Machine

    Setting up the machine Setting up the machine Setting up the machine Insert both ends of the film in-between the upper and lower heat rollers using the threading card (should come with the laminating rolls) Once the film is fed fully through the machine, set lever to “UP”...
  • Page 15 At this time, the machine will take a few minutes to heat up At 80 degrees Celsius, you will hear a beep from the machine. This is to let you know that when the temperature reaches 90 degrees, the rollers will start to turn. Press heat button again to silence beeping.
  • Page 16 Align the feed tray with appropriate notches, and set into place. Machine will beep once again when desired temperature is reached and green ready light will go on.
  • Page 17 Lever positions Lever positions Lever positions Lever should be in “DOWN” position Lever should always be in “UP” when machine is in use position when machine is NOT in use...
  • Page 18 Trim blade Trim blade Trim blade The trim blade is used to separate your current laminated project from the rest of the material. Trim blade Caution: The blade is very sharp and should be used with utmost care. Run blade through material from left to right to cut finished product from the rest of the film.
  • Page 19 Feeding Feeding Feeding Feed the papers to be laminated in Gently pull the laminated paper at between the upper and lower heat the back. (if you don’t pull, the laminated paper might attach to the machine and get rollers, as shown above wrinkled, due to static electricity)

  • Page 20: Switching Off The Machine

    Switching off the machine Switching off the machine Switching off the machine Set the temperature to 80 degrees Celsius. Press Cold button – the machine will start to cool down Press and hold speed down button for 3 – 5 seconds to set the speed to “0”.

  • Page 21: Troubleshooting

    Trouble shooting Trouble shooting Trouble shooting Wrinkles Tension can be adjusted for the purpose of creating the right resistance for the rolls of laminating film. This is achieved by turning the silver knobs on the right side of the machine that line up with the upper and lower mandrills.
  • Page 22 Trouble shooting Trouble shooting Trouble shooting Reverse Button Reverse button is used to back the film out in case of any jams or errors in lamination. When pressed, the film will feed back out towards the front of the machine. When released, the machine will start feeding the film normally again.
  • Page 23 Trouble shooting Trouble shooting Trouble shooting ue Buildup When machine is improperly heated to too high temperature or film is improperly aligned, you may notice markings along the side of the film where excess glue is building up on the rollers.
  • Page 24 Operating instructions manual Operating instructions manual Operating instructions manual Refer the enclosed instructions manual for additional information...