Page 1
Home Network System Access Keypad KX-HNK101AZ Model No. Thank you for purchasing a Panasonic product. This document explains how to operate the access keypad properly. For details about how to use the system, refer to the User’s Guide (page 17).
Table of Contents Introduction Accessory information ....3 Important Information Graphical symbols for use on equipment and their descriptions .......4 About this system ......5 For your safety ......5 Important safety instructions ..6 For best performance ....6 Other information .......7 Setup Part names and functions ..8 Touchpanel buttons ....8 LED indicator ......9 Setup overview ......9...
Introduction Accessory information Supplied accessories Accessory item/Part number Quantity AC adaptor/PNLV226AL Mounting bracket Wall mounting screws (25 mm) Wall anchors The mounting bracket is attached to the product at the time of shipment. Other information R Design and specifications are subject to change without notice. R The illustrations in these instructions may vary slightly from the actual product.
Important Information Graphical symbols for use on equipment and their descriptions Symbol Explanation Symbol Explanation Alternating current (A.C.) Class P equipment (equipment in which protection against electric shock relies on Double Insulation or Reinforced Insulation) Direct current (D.C.) “ON” (power) Protective earth “OFF”...
R The AC adaptor is used as the main disconnect device. Ensure that the The hub and other compatible AC outlet is installed near the Panasonic devices use radio waves to product and is easily accessible. communicate with each other.
Important Information R For maximum coverage and Move away from the electrical noise-free communications, place appliances. your hub: – at a convenient, high, and central location with no obstructions Other information between the product and hub in an indoor environment. Routine care –...
Setup Part names and Touchpanel buttons functions These buttons allow you to confirm and change the system’s arm mode. During normal operation, the button that corresponds to the current arm mode is lit by default, and all other buttons are dimmed.
Setup LED indicator Registering the keypad You can use the LED indicator to confirm the keypad’s status. This procedure is not required for Indicator Status devices that were included as part of a bundle. Normal operation, or no power Before you can use the keypad, it must Red, Keypad is not be registered to the hub.
Setup Using the app Usage area cautions When you register the keypad by using Using the keypad in the following areas the [Home Network] app, you can may cause deformation, malfunction, or assign a name to your devices and operational failure. group them by location.
Setup Installation To mount the keypad flat against the wall, use the mounting bracket. Note: R Mount the keypad on the stable location where the keypad can be adequately supported when mounting. R Do not mount keypad on a soft material. It may fall down, break, or cause injury. R Do not mount the keypad on a plywood surface that is less than 25.4 mm thick.
Page 12
Setup Place the mounting bracket against the wall and determine where the mounting bracket will be installed. Mark the screw openings on the wall. R Refer to the information below. The dotted lines indicate where the edges of the keypad will be in relation to the mounting bracket. 16 mm 59 mm 19 mm...
Page 13
Setup Installing the mounting bracket Installing the mounting bracket on wooden walls Line up the holes on the mounting bracket with the holes in the wall, then insert and tighten each screw. Note: R Use the supplied screws ( R Place the bracket with the “UP” mark facing upwards. Installing the mounting bracket on gypsum board, ALC (autoclaved lightweight cellular concrete), or concrete blocks Use the supplied anchors and screws to mount the mounting bracket to the wall.
Page 14
Setup Insert the anchor into the hole so that it is flush with the wall surface. Line up the holes on the mounting bracket with the anchors, then insert and tighten each screw. R Use the supplied screws ( R Place the bracket with the “UP” mark facing upwards. Installing the keypad to the mounting bracket Attach the keypad to the bracket.
Page 15
Setup Connecting the AC adaptor Note: R Use only the supplied Panasonic AC adaptor PNLV226AL. Connect the AC adaptor plug to the keypad until you hear a click (A) and connect the AC adaptor to the power outlet (B). Note about power connections AC adaptor connection R The AC adaptor must remain connected at all times.
Appendix To cancel the trigger, tap the touchpanel, enter the disarm PIN Using the keypad (default: “0000”), and then tap MOKN. Changing the arm mode Talking notification feature Tap the touchpanel to light the arm This feature allows you to get mode buttons.
Approx. 120 mm ´ 120 mm ´ 21 mm R Android 4.1 or later versions are R Mass (weight) recommended. Approx. 163 g (without the mounting R You can also access the User’s bracket attached) Guide at the web page listed below. www.panasonic.net/pcc/support/tel/ homenetwork/manual/...