1.2.2 Installation Damage due to unsuitable mounting location The environmental conditions recommended by the manufacturer must be observed. Do not operate the device in excessively dusty places. Do not expose the device to mechanical vibrations or shocks. Siemens AG 04.2011...
There is a risk of minor injuries or damage to property IMPORTANT Malfunctioning may result Meaning of the hazard symbols The nature of the hazard is indicated by icons. CAUTION Dangerous area! CAUTION Dangerous electrical voltage! Important information Siemens AG 04.2011...
Directives and standards Directives and standards The product complies with the requirements of the following EU directives. The EU declaration of conformity is available from: Siemens AG Siemensallee 84 76181 Karlsruhe European Directive 2004/108/EC "Electromagnetic Compatibility" Compliance with the European Directive 2004/108/EC has been proven by testing...
Details for ordering Details for ordering Type Part no. Designation Weight CCAW1417-LPI S54561-C34-A1 ¼-inch Camera D/N WD AF 0.4 kg Package contents Camera Installation Instruction 12-pin interface cable Software and documentation on CD Siemens AG 04.2011...
Digital slow shutter (DSS) Automatic white balance (AWB) Automatic gain control (AGC) On-screen menu (OSD) Negative/Positive switching (NEGA/POSI) E function (H/V flip, rotation) High resolution Motion detection and face detection Privacy masking Zoom preset and tour function Home preset Siemens AG 04.2011...
The focus keys are activated when AF mode is Off. BNC connector Monitor connection port Power input terminal 24 V AC / 12 V DC Power indicator LED DIP switch Twisted-pair video output parameters Front view Side view Rear view Siemens AG 04.2011...
When using the camera in conjunction with a video matrix switcher (SIMATRIX SYS, 648, 164) or other telemetry equipment (different protocol), an interface converter CAC0103 is required. Typical system configuration with directly controlled cameras ..Camera C1..C10 RS485 Keyboard Video Monitor Siemens AG 04.2011...
Control RS-232 connection, Light blue TxD PC configuration Brown MD output Violet MD/FD off: 0 V, on: 3.3 V Power supply +12 V DC / 24 V AC White - 12 V DC / 24 V AC Siemens AG 04.2011...
The camera can be controlled remotely by an external device or control system, such as a control keyboard, using RS-485 half-duplex. Connect marked Rx+, Rx- to Tx+ and Tx- of the RS-485 control system. RS-485(+) Black RS-485(-) Pink Siemens AG 04.2011...
5 MHz 6 dB 6 dB 12 dB Condition on delivery 8.1.4 Alarm output The alarm output (motion detection result or face detection result or external signal fed in) is active high. Alarm output Violet Siemens AG 04.2011...
Remote configuration MENU TELE NEAR WIDE 42mm Abb. 4 Remote configuration – circuit diagram Camera Yellow Remote control Orange Remote control unit Remote control White Black Remote control unit The remote control cable must not be extended. Siemens AG 04.2011...
Min. distance in focus between camera and object D-ZOOM 0.1 / 1.0 / 1.5 / 2.5 / 6.0 m D-ZOOM END Digital zoom function On/Off ZOOM PRESET Max. digital zoom factor: x2 – x16 SET PRESET Zoom preset number: 1 – 10 Siemens AG 04.2011...
Since the colour rolling path differs depending on the fluorescent lamp used, it has to be adjusted individually. To do so, select the WB menu. After about 10 s, the adjust mode will be finished automatically. Back to the next higher menu level Siemens AG 04.2011...
Select BLC area: 1-9, activated only in manual BLC mode BLC LEVEL Back-light compensation level: LOW, MID, HIGH WDR MODE WDR (Wide Dynamic Range) function On/Off WDR LEVEL WDR level: 10 – 50 Back to the next higher menu level Siemens AG 04.2011...
Adjust the location of the mask area with boundary bottom and right COLOUR Mask colour: 1 – 8 MOSAIC Mosaic display On/Off MOSAIC TYPE Mosaic roughness setting: 1 – 4 Back to the next higher menu level Siemens AG 04.2011...
Digital flip function: vertical flip/horizontal flip/180° rotation FREEZE Real or still mode HI-RES High-resolution mode: Low/Mid/High 2DNR 2D noise reduction level: Off/01 – 07 3DNR 3D noise reduction level: Off/01 – 31 Back to the next higher menu level Siemens AG 04.2011...
CAM ID Camera ID: 1 – 255 BAUD RATE Serial communication speed: 2400/4800/9600/19200 PROTOCOL Operating protocol: COMMAND: for factory use only SIEMENS – B (Parity = Even) SIEMENS – S (Parity = Even) MOLYNX (Parity = Even) PELCO – D (Parity = None) PELCO –...
Therefore, the following maintenance tasks should be performed on a three-monthly basis: Inspect all connection cables for deterioration or other damage. Clean all components with a soft, clean cloth. Check that all fixings are secure. Siemens AG 04.2011...
It is a precondition for reuse and recycling of used electrical and electronic equipment. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. Siemens AG 04.2011...