Siemens M35 Series Service Manual
  1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Cell Phone
  5. M35
  6. Service manual

Siemens M35 Series Service Manual

Hide thumbs Also See for M35 Series:
Table of Contents

Quick Links

See also: User Manual , Installation Manual
Local Service Organization Service Manual
M 3 5 S e r i e s
M 3 5 S e r i e s
S I E M E N S C O M M U N I C AT I O N S U N L I M I T E D
V1.0
Table of Contents
loading

Related Manuals for Siemens M35 Series

Summary of Contents for Siemens M35 Series

  • Page 1 Local Service Organization Service Manual M 3 5 S e r i e s M 3 5 S e r i e s S I E M E N S C O M M U N I C AT I O N S U N L I M I T E D V1.0...

  • Page 2: Table Of Contents

    C H A P T E R 2 Configuring the test software Level 2 Service Guide Running the test sequence Introduction ANNEX A M35 Series Technical Information ANNEX B Accessories General Information C H A P T E R 4 M35 Series Exploded Diagram Level 2.5 Repair Document...

  • Page 3: Cellular Communication

    Chapter Cellular Communication Coverage Concept he cellular systems is made up of numerous transmitting and receiving sites, whose individual coverage areas partially overlap. The concept of frequency re-use, same frequency is used by several sites, allows a high traffic density in a wide area. Due to the limited transmission range of the terminals, cellular systems are based on a large number of base stations on the infrastructure side, scattered over the area to cover, with each covering a fairly small geographical zone called cell.

  • Page 4: Gsm Network Architecture

    GSM Network Architecture. GSM network can be broadly divided into three broad parts, namely: 1. Mobile Station(MS) carried by the subscriber, 2. Base Station Sub-system(BSS) which controls the radio link with the mobile station. 3. Mobile Switching Center(MSC) which performs the switching of calls between the mobile users, and between mobile and fixed network users.

  • Page 5: Subscriber Identity Module

    Authentication Center, AUC Stored information that is necessary to protect communication through the air interface against any intrusions. The legitimacy of the subscriber is established through authentication and ciphering, which protects the user information against unwanted disclosure. Equipment Identity Register, EIR An option the network operator can use to enforce security.

  • Page 6: Sim Application Toolkit

    To protect the SIM card from improper use, a security feature, a four digits personal identification number(PIN), is built in. The PIN is stored in the card and can be changed by the subscriber. PIN2 is required for additional funtions available with a special SIM card (Consult the operator for more information about the PIN.

  • Page 7: Extended Gsm 900 - Egsm

    When active, the name of the service may appear in the menu, and there will be sub-menu if more than one application is active. Figure 1.4 is the SAT icon. FIGURE 1.4 SAT ICON Extended GSM 900, E-GSM This is a new standard that allows Network Operators to increase their capacity through an extended frequency.

  • Page 8: Data Application

    1.1. Level 2 Service Guide Introduction The chapter is intended to help you carry out repair up to Level 2 on the M35 series mobile phone. The repair for international version and Asian variants are identical unless otherwise noted, therefore the description herein is confined to M35i only.
  • Page 9 M35i Technical Information System GSM Phase 2, Dual Band EGSM 900, Class 4(2 Watt) GSM 1800, Class 1(1 Watt) Operating Voltage 3.6V Size(LxWxH) 118 x 47 x 22.6 mm Volume 99cm including battery (approx) Weight 130g including battery (approx) Battery(Standard) NiMH, 500mAH(Standard) Li-Ion, 600mAH(Optional) Standby time...
  • Page 10 PIN control PIN 1 & 2 Code Control Phone code 4 to 8 digit code Network function Automatic and manual network selection Chipset Siemens E – GOLD WAP Browser Version 1.1 Other FeaturesClock / Alarm Alarm List Built-in modem Calculator...

  • Page 11: Accessories

    Accessories: 1. Standard Battery L36880-N4001-A100 2. Optional Battery L36880-N4001-A101 Standard Charger L36280-Z4-CXXX (Country Variant) 4. Travel Charger L36880-N4001-A103 (EU) / A104 (UK) Similar to standard charger with an universal input voltage from 90 ~ 240V 4. Desk Top Charger L36880-N4001-A102 5.

  • Page 12: General Information

    General Information Information Due to different requirements of the markets, the M35 has different variants, which broadly classified under International version and Asian version. Marketing name for international version is M35 or M35i, whereas Asian version is named M3508 or M3508i. Difference between M35(18) and M35(18)i M35(18)i mobile software has WAP Browser 1.1 incorporated thus enabling user to surf the Internet and it have the built-in soft modem for GSM Data Service.
  • Page 13 4. Wireless Transport Layer Security WTLS incorporates security features that are based upon the established Transport layer Security (TLS) protocol standard, that include data integrity checks, privacy on the WAP Gateway to client leg and authentication. 5. Wireless Datagram Protocol Allows WAP to be bearer independent by adapting the transport layer of the under-laying bearer.
  • Page 14 M35 Series Mechanical Diagram FIGURE 2.1 M35I MECHANICAL DIAGRAM. Please take note that the number(s) used here IS NOT the part  number, DO NOT used it in your spare parts purchase order. A l w a y s r e f e r t o t h e S E R V I C E P A R T P R I C E L I S T...

  • Page 15: Mechanical Concept

    Mechanical Concept Note: All numbers refer to mechanical drawing in Figure 2.1. The mechanical concept of the M35 differs in various points from the one of the other Siemens mobile telephones. The first thing you will experience is how the housing is locked. In M35 no screws are used to keep the housing closed.

  • Page 16: Hardware Concept - Block Diagram

    Hardware Concept – Block Diagram FIGURE 2.2 M35 BLOCK DIAGRAM.

  • Page 17: Hardware Description

    Hardware Description The handset consists of the following major integrated circuits: 1) E-GOLD – PMB2851E This IC is a combination of microprocessor, signal processor and real-time clock. The microprocessor part of this component is responsible for controlling the keyboard, SIM- Card, Flash and RAM.
  • Page 18 This circuit provides the following main functions: • Control of switch on of the Mobile phone by ON/OFF button, Ext Power (Charger) or real time clock. • Watchdog monitor – switch off the mobile phone if no proper Watchdog signal send from HiGOLD IC.

  • Page 19: Power Supply Concept

    The charging current must not rise above 1A or a track fuse in the phone will blow. As a result charging the battery will no longer by possible.  Be careful with NON-original SIEMENS accessories or chargers. Make sure that the charging current is limited to value below 1A.

  • Page 20: Battery Charging

    Battery Charging M35 series uses a Nickel Metal Hyride (NiMH) 500mAH battery pack as standard battery. It also support the Lithium Ion 600mAH battery pack (For S35i phone) as optional battery for customer want longer talk time. PHOTO 2.3 M35i SERIES INSERTING BATTERY.

  • Page 21: Deep Discharge Battery

    PHOTO 2.4 INSERT CHARGER Photo 2.4 shows the correct way of inserting and removing the charger plug. Deep Discharge Battery In case of a deeply discharged battery, the voltage of the battery is too low to operate the charging circuit and the display controller, the phone can not be turned on and the normal charging process can not be started.
  • Page 22 Mobile Phone M35 Spare Parts Level 1 and Level 2 Level 1 Part No. L36158-A33-C101 Display Cover (Displaymodule) C35/C35i/M35i L36158-A33-C103 Display Sealing (Displaymodule) C35/C35i/M35i L36158-A36-A1 Upper Case Shell M35i blue L36158-A36-A4 Upper Case Shell M35i yellow L36158-A36-A5 Upper Case Shell M35i grey L36158-A36-A12 Upper Case Shell M35 (China) grey black L36158-A36-A30...

  • Page 23: Disassemble The M35

    Disassemble the M35 A case opener is needed to disengage the latch of the M35 casing. PHOTO 2.5 C35/M35i/S35i CASE OPENER  The part number for this mandatory tool is F30032-P46-A1 Refer to ANNEX B of Chapter 3 for Service Equipment List. STEP 1: Unlock the battery cover of the battery with the plastic coin that shipped with the M35i phone as shown in PHOTO 2.6 &...
  • Page 24 STEP 2: Remove the battery cover and the battery as shown in PHOTO 2.8 & PHOTO 2.9 and keep the Battery Cover, Battery, Battery Sealing, Accessory Connector Cover and External Antenna Cover for Assembly of M35i . PHOTO 2.8 DISASSEMBLE M35i – STEP 2 PHOTO 2.9 DISASSEMBLE M35i –...
  • Page 25 Disassemble/Assemble of the Lower Housing Assembly STEP 1: Open the housing with the opening tool and carefully pull the lower housing section off as illustrated in PHOTO 2.12 PHOTO 2.12 Lower Housing Assy – STEP 1 PHOTO 2.13 Disassembly Lower Housing – STEP 2 STEP 2: Remove in sequence by hand the SIM Card Holder, SIM Card Reader, Battery Contact Spring, and Vibra-Alert Unit as illustrated in PHOTO 2.13...
  • Page 26 STEP 2: Unlock the catches of the Display Module from the Control Board and move the display module to the lower part of the PCB. Lift up carefully the retaining clip of the display connector on the Control Board as illustrated in PHOTO 2.15 PHOTO 2.15 Disassemble Control Board Assy –...
  • Page 27 STEP 2: Disengaged the catches of the Back Cover and Front Display Cover to separate the housing and the Control Board Assembly as in PHOTO 2.19 and remove in sequence by hand the Back Cover, LCD Flexi-PCB and the Display Mask as illustrated in PHOTO 2.20 PHOTO 2.19 Disassembly Display Module –...

  • Page 28: Assemble The M35

     The loudspeaker is glued to the upper housing section by a foam covered with glue on both sides. When you remove it, the foam will be damaged. Please use new loudspeaker for assembling Upper Housing Assembly. For assembly of a new Upper Housing install a new earphone first, watch out for the orientation. For install of the other parts just reverse the sequence for the disassembly.
  • Page 29 STEP 3: Close the device by putting on the Upper casing section as illustrated in PHOTO 2.25. Hold the phone and use both hands to close the casing starting from the catches at the top part near the antenna, watch out for leaving any finger marking on the display screen. n o t p l a c e t h e...

  • Page 30: Mobile Software Programming

    1. Software update to actual version and appropriate language group 2. Programming of CUSTOMER SPECIFIC INITIALIZATION Mobile Software Updating The software of the mobile, M35 series, is loaded from a PC directly. Hardware interconnection between the mobile and the PC is shown in Figure 2.6 RS232 Port...
  • Page 31 If you use the X35 battery dummy, then make sure that the power supply voltage is correctly adjusted 4.0V & 3A current rating. Description Part No. Adaptor-Cable-Bootadaptor, X25/X35 V30146-A5004-D Boot Adaptor L24857-F1006-A30 IBM Compatible PC – Pentium TABLE 2.1 EQUIPMENT LIST FOR SOFTWARE PROGRAMMING.

  • Page 32: Language Groups

    SOFTWARE IS A DOS-BASED PROGRAM, IT IS ADVISABLE TO DO THE SOFTWARE UPGRADE IN DOS ENVIRONMENT. Languague Groups There are over 20 languages for the M35 series in total. These languages are divided into groups as follows M35i Group Languages English, German, French, Italian, Dutch, Swedish, Finnish, Norwegian, Danish.
  • Page 33 This executable file needs a definition or init file, named SWUP.INI, to define the message language preferences and the hardware communication port set up. The content of this file consists of the following text: Language=English COM=x Where x is the number that corresponds to the serial port that is used, either 1, 2 or 3. Flow chart 2.1 illustrates the software programming process.

  • Page 34: Customer Specific Initialization

    Re-use of IMEI label is possible by using a hair-dryer to remove the IMEI label. On this IMEI label, Siemens has also includes the date code for production or service, which conforms to the industrial standard DIN EN 60062. The date code comprises of 2 characters: first character denotes the Year and the second character denotes the Month.

  • Page 35: Phone Unblocking

    * # 0 0 0 3 * - - - - - - - - # The Master Phone Code can be obtained by: 1. Fax to Siemens Hotline in Germany Siemens AG ICP CD SH World Service Center, Bocholt, Germany +49-2871-91-3007 2.
  • Page 36 PHOTO 2.19 INTERNET PAGE PHOTO 2.20 INTERNET PAGE: MASTER PHONE CODE  Contact your Service Manager for more information regarding setting up of the INTERNET SOLUTION & its installation procedure, ASC/T002/98.

  • Page 37: Siemens Service Equipment

    2. Set which pass the test will be good enough to return to customer. Starting from the P35 Series, Siemens will introduce a simpler and faster testing platform for testing a repaired Siemens mobile phone. The testing platform are either base on R&S CMD 53/55 or CTS55 GSM test set.
  • Page 38 R&S CMD55 Test Station R&S CTS55 Test Station...

  • Page 39: Other Equipment

    Wavetek 4201S Test Station Other equipment One Pentium MMX Window 95/98 PC with a serial port to connect to the GSM test set through the PC serial cable provided for the GSM test set. One Test SIM card and a fully charged battery for used with the mobile phone model. Additional RF connector will be needed for setup using Wavetek 4107 test set and Wavetek Antenna Coupler.

  • Page 40: Software Installation

    Software Installation Before executing the test software, it is important to ensure that the software configuration matches that of the hardware set up. Each GSM Tester will have a specific test software. The test software are name CMD_GO, CTS_GO and for Wavetek test set, CAT4200 respectively. First, copy the installation software for the specific GSM tester to a temporary directory on the harddisk of the Window PC and then Run the Setup from the first sub directory –...

  • Page 41: Configuring The Test Software

    Configuring the test software For each model of the P35 series mobile phone, Siemens will distribute the testing configuration file for the specific test station. For testing the phone, just go to the File menu and select Load Configuration.

  • Page 42: Running The Test Sequence

    Service Info SB_0500 for the CTS/CMD Hardware Options. Insert a Test SIM card and a fully charged battery into the Siemens mobile phone and place it onto the phone holder on the Antenna Coupler. Switch the RF switch to INT ANT position and select the Start button to run the test sequence in the configuration file.
  • Page 43 Next, the GSM test set will initial a call to the mobile phone through the Antenna Coupler. Press the Call key when the mobile phone ring, and the GSM test set will start Tx Power measurements on the GSM and GSM1800 channel specified by the configuration setting. Next, the GSM test set will end the call to the mobile phone and the screen will prompt for Dialing from the mobile phone.
  • Page 44 The GSM test set will make Tx Power measurements, Rx BER measurement, Echo Loop test on the GSM and GSM1800 channel specified by the configuration setting. There will be 2 Echo Loop Back test for checking the speech quality – one for GSM and one for GSM1800. Speak into the mobile phone when prompted and listen the voice after appr.
  • Page 45 A measurement report screen will show up and a hardcopy can be printed if a printer is connected to the PC. To close the measurement report screen, click the third button from the left. Once the mobile phone pass all the test steps, please make a check for all the key and the display.

  • Page 46: Annex A

    ANNEX A Cable Specifications 1. PC to NGSM(Power Supply) Depending on the type of serial connector that is used by the PC. The cable layout for both 9pins and 25pin are listed below: Computer: NGSM: Sub-D 25 pins Sub-D 25 pins Pin 2 Pin 3 Pin 3...
  • Page 47 Sub-D 9 pins Sub-D 9 pins Pin 3 Pin 2 Pin 2 Pin 3 Pin 6 Pin 4 Pin 5 Pin 5 Pin 4 Pin 6 Pin 8 Pin 7 Pin 7 Pin 8 TABLE A.4 D9 TO D9 CONNECTION 3.
  • Page 48 Internal dip switches of the power supply, NGSM 32/10, must be set correctly to ensure proper communication between PC and the NGSM. These switches are set up by Siemens and tested before delivery, hence it is not necessary to change it normally.

  • Page 49: Annex B

    ANNEX B Service Equipment List All purchases of jigs, tools and test equipment must be order directly from Siemens Germany. Attach the standard form with your purchase order and send it to ICP CD SL and ICP CD ST. Pos.

  • Page 50: Level 2.5 Repair Document

    Chapter Level 2.5 Repair Document Introduction The C/M/S35 product family consists of 5 different dualband handsets (GSM-900 and GSM-1800), which can easily be distinguished from the second block of the part number printed on the IMEI label. There also exist Asian variants of C/M/S35 named 3508 / 3518 / 3568 respectively.
  • Page 51 Tel.: +49 2842 95 4666 Fax: +49 2842 95 4302 e-mail: [email protected] This manual is intended to help you carry out repair on Level 2.5, i.e. limited component repair. Failure highlighted in this document should be repaired in the local workshop.

  • Page 52: Antenna Connector

    Antenna Connector Affected Units Type: C/M/S35 Affected IMEIs / Date Codes: All / All Affected SW-Versions: Fault Code for LSO reporting: 3ANC Fault Description Fault Symptoms for customers: Network Search when using the external antenna (carkit) No location update possible on external antenna (carkit) Fault Symptom on GSM-Tester: Output power problems on the external antenna No location update possible...
  • Page 53 Priority:  ..Mandatory  ..Repair  ..Optional  ..Not Yet Defined Repair Documentation Description of procedure: D I A G N O S I S Check the output power of the handset with the LSO testprogram. Especially watch the external antenna power! R E P A I R B Y C O M P O N E N T C H A N G E Use hot air blower to remove defective connector...
  • Page 54 S P E C I A L T O O L S None W O R K I N G M A T E R I A L S Desolder Wick / Braid Solder Drawings Figure 1: X35 Board Antenna Connector Side (Top View)

  • Page 55: Ringer

    Ringer Affected Units Type: C/M/S35 Affected IMEIs / Date Codes: All / All Affected SW-Versions: Fault Code for LSO reporting: 3RIN Fault Description Fault Symptoms for customers: Problems with the handset ringer. No ringer tone audible. Fault Symptom on GSM-Tester: Handset fails ringer test.
  • Page 56 Repair Documentation Description of procedure: D I A G N O S I S Visually check the ringer. Watch for physical damage or dry joints. R E P A I R B Y C O M P O N E N T C H A N G E Resolder dry soldering joints.
  • Page 57 S P E C I A L T O O L S None W O R K I N G M A T E R I A L S Desolder Wick / Braid Solder Flux Drawings Figure 1: X35 Board Ringer Side Figure 2: X35 Ringer (B800) Placement (Top View)

  • Page 58: Bottom Connector (Lumberg)

    Bottom Connector (Lumberg) Affected Units Type: C/M/S35 Affected IMEIs / Date Codes: All / All Affected SW-Versions: Fault Code for LSO reporting: 3LUC Fault Description Fault Symptoms for customers: Charging problems. Problems with external loudspeaker or microphone when using a car kit. Problems with accessories connected at the bottom connector.
  • Page 59 Repair Documentation Description of procedure D I A G N O S I S Visually check the bottom connector. Watch for dry joints! R E P A I R B Y C O M P O N E N T C H A N G E Use hot air blower remove defective bottom connector.
  • Page 60 W O R K I N G M A T E R I A L S Desolder Wick / Braid Solder Drawings Figure 1: X35 Board Bottom Connector Side Figure 2: X35 Bottom Connector Placement (Top View) Pin 12 Pin 1 Table 1: X35 Bottom Connector Pin Description...
  • Page 61 Name IN/OUT Notes Charger coding and charger control. POWER Charging Current FBatt+ Power supply for the accessories. Serial interface Serial interface ZUB_CLK Clock line for accessory bus Use as DTC In data operation ZUB_DATA I/O Data line for accessory bus. Use as CTS in data operation GND_MIC...

  • Page 62: Display Connector

    Display Connector Affected Units Type: C/M/S 35 Affected IMEIs / Date Codes: All / All Affected SW-Versions: Fault Code for LSO reporting: 3DIC Fault Description Fault Symptoms for customers: Display problems, like missing lines or columns on the LCD or display contrast problems. Fault Symptom on GSM-Tester: Display test fails.
  • Page 63 Repair Documentation Description of procedure: D I A G N O S I S Visually check the status of the display connector. Watch for oxidation and dry solder joints. Mechanically check the opening / closing mechanism. R E P A I R B Y C O M P O N E N T C H A N G E Use hot air to remove defective connector Avoid excessive heat! Watch surrounding components!!
  • Page 64 List of needed material C O M P O N E N T S D I S P L A Y C O N N E C T O R Part-Number: L36195-Z26-C629 J I G S A N D T O O L S Soldering Iron Hot Air Blower S P E C I A L T O O L S...
  • Page 65 Drawings Figure 1: X35 board display connector side Figure 2: X35 display connector placement (Top View)

  • Page 66: Keyboard Led

    Keyboard LEDs Affected Units Type: C/M/S 35 Affected IMEIs / Date Codes: All / All Affected SW-Versions: Fault Code for LSO reporting: 3LED Fault Description Fault Symptoms for customers: Keyboard Illumination not working. Fault Symptom on GSM-Tester: This fault cannot be detected with a GSM-Tester Priority: ...
  • Page 67 Repair Documentation Description of procedure: D I A G N O S I S Use the diode test function of a multimeter to check the status of the diode. The typical voltage drop on the diode is 1.7V when testing the diode function with the multimeter.
  • Page 68 S P E C I A L T O O L S None W O R K I N G M A T E R I A L S Desolder Wick / Braid Solder Drawings Figure 1: X35 board keyboard LED Side Figure 2: X35 keyboard LED placement and polarity (top view)
  • Page 69 Display LEDs Affected Units Type: C/M/S 35 Affected IMEIs / Date Codes: All / All Affected SW-Versions: Fault Code for LSO reporting: 3LED Fault Description Fault Symptoms for customers: Display Illumination not working. Fault Symptom on GSM-Tester: This fault cannot be detected with a GSM-Tester Priority: ...

  • Page 70: Display Led

    Repair Documentation Description of procedure: D I A G N O S I S Use the diode test function of a multimeter to check the status of the diode. The typical voltage drop on the diode is 1.7V when testing the diode function with the multimeter.
  • Page 71 S P E C I A L T O O L S None W O R K I N G M A T E R I A L S Desolder Wick / Braid Solder Drawings Figure 1: C/M35 board display LED Side Figure 2: C/M35 board display LED placement and polarity...
  • Page 72 Figure 3: S35 board display LED side Figure 4: S35 board display LED placement and polarity...

  • Page 73: Infrared Diodes

    Infrared Diodes Affected Units Type: S 35 Affected IMEIs / Date Codes: All / All Affected SW-Versions: Fault Code for LSO reporting: 3INF Fault Description Fault Symptoms for customers: No infrared connection possible. Fault Symptom on GSM-Tester: This fault cannot be detected with a GSM-Tester. Priority: ...
  • Page 74 Repair Documentation Description of procedure: D I A G N O S I S Visually check the status of the IrDa module. Watch for dry solder joints. Use a reference infrared port (eg. from a notebook) to check the IrDa function.

  • Page 75: Annex C

    ANNEX C PC Adaptor Cable & Accessories C35 Adapter Cable E-Box-PC L36880-N3101-A112 Adapter Cable PC-Mobilephone L36880-N3101-A102 Belt Clip L36880-N4001-A113 VDA Adaptercable L36880-N4001-A121 Car Kit Portable Handsfree Set L36880-N3015-A117 12 V Headset Car Kit Portable Handsfree Microphone L36880-N4001-A123 L36254-Z6-C75 Microphone Accessories Kit Car Charger Cable 10,8-24V Car Holder L36158-A98-C6...

  • Page 76: Power Plug For M35

    Power Plug for C35, M35 , S35 L36280-Z4-C321 L36280-Z4-C324 L36280-Z4-C325 L36280-Z4-C323 L36280-Z4- C322 Power Plug Travel Charger 90-240 V Travel Charger 90-240V L36880-N4001-A103 L36880-N4001-A104 Desktop Charger L36880-N4001-A102...
  • Page 77 Car installation kit Ratio unit C35, M35 & Cradle Comfort L36158-A37-B1 Handset L36880-N3015-A123 Connection Box Ratio L36880-S4001-A300 Handsfree Microphone L36880-N4001-A116 Con. Cable Battery Comfort L36146-A2053-D Phone In Adapter L36880-N3015-A137 Not included in our Standard Dellivry...
  • Page 78 Car installation kit hands free unit C35, M35, S35 Handsfree Loudspeaker Phone In Adaptor L36104-F3090-X902 L36880-N3015-A137 Con. Cable Battery Comfort L36146-A4013-D Fuses 3A Radio Mute black Battery Battery Ground brown Ignition violet 1,8m Connection Box L36880-S2001-A100 Handsfree Microphone L36254-Z6-C76 Handset Cradle Comfort L36880-N3015-A123 L36158-A37-B1...
  • Page 79 Carkit installation kit hand free unit Professional C35, M35, S35 Handsfree Loudspaker L36104-F3090-X901 Con. Cable Battery L36146-A1030-D Radio Mute black Lights Dimmer yellow Automatic Antenna Fuses 3A white Battery Battery ground brown 1,9m Ignition violet Handfree Microphone L36254-Z6-C63 Push to talk cable L36146-A4012-D Adapter Cable E-Box-PC...
  • Page 80 Carkit installation Comfort GPS C35, M35, Handset L36880-N3015- Combi Antenna GPS A123 L36851-Z1901-A46 Crash Sensor Con. Pox L36880-N4001-A115 Connection Pox GPS L36880-S4001-A4 Car Cradle Telematic L36158-A37-B6 Antenna Handsfree Loudspeaker L36104-F3090-X902 Handsfree Microphone L36880-N4001-A116 Con. Cable Battery L36146-A2053-D Phone In Adapter L36880-N3015-A137 Not included in our Standard...
  • Page 81 PC Adaptar Cable & Accessory C35, M35, S35 Adaptor Cable E-Box -PC L36880-N3101-A112 Adapter Cable PC-Mobilephone L36880-N3101-A102 Belt Clip L36880-N4001-A113 VDA Adaptercable L36880-N4001-A121 Car Kit Portable Handsfree Set L36880-N3015-A117 12 V Car Kit Portable Handsfree Microphone L36254-Z6-C75 Headset L36880-N4001-A123 Car Holder Microphone Accessories Kit Car Charger cable 10, 8 –...

  • Page 82: References

    IrDA(Infrared Data Association), Serial Infrared Physical Layer Link Specification, Version 1.1, October 15, 1995. Disclaimer: This content is subjected to change without notice. Copyright © 2000 Siemens Advanced Engineering Pte Ltd ICP CD Asia Service Center, 164, Kallang Way, #04-22, Kolam Ayer Industrial Estate, Singapore 349248 Author: Tan Guan San.

Table of Contents