Fujitsu ETERNUS DX60 Configuration Manual

Disk storage system
Hide thumbs Also See for ETERNUS DX60:
P3AM-3182-15ENZ0
FUJITSU Storage
ETERNUS DX
Configuration Guide -Server Connection-
(Fibre Channel) ETERNUS DX60/DX60 S2, DX80, DX90 Disk Storage System
Settings
Table of Contents
loading

Summary of Contents for Fujitsu ETERNUS DX60

  • Page 1 P3AM-3182-15ENZ0 FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX60/DX60 S2, DX80, DX90 Disk Storage System Settings...
  • Page 2 This page is intentionally left blank.
  • Page 3 ETERNUS DX, server, OS, Fibre Channel Card, Converged Network Adapter cards, and drivers. Refer to "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Notations" for the notations used in this manual such as product trademarks and product names. For storage systems that are supported by the OS, refer to the Server Support Matrix of the ETERNUS DX.
  • Page 4: Table Of Contents

    2.1.4 Creating and Allocating LUN Groups (Setting Host Affinity Groups) ..............12 2.2 Specific Settings ........................... 13 2.2.1 Setting the Reset Groups.............................13 2.2.2 Setting the Subsystem Parameters (for HP-UX only)...................14 2.3 Checking the WWNs ........................14 FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2015 FUJITSU LIMITED P3AM-3182-15ENZ0...
  • Page 5 Transfer rate setting values ........................8 Table 2.3 FC port parameter settings (Fabric connection) ..................9 Table 2.4 Transfer rate setting values ........................9 Table 2.5 Host response settings ..........................10 FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2015 FUJITSU LIMITED P3AM-3182-15ENZ0...
  • Page 6: Chapter 1 Workflow

    Chapter 1 Workflow This manual is used when performing the setup procedures described in the "Setting Up the ETERNUS DX" section of the "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel)" for each OS. Required Documents "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) Fibre Channel •...
  • Page 7 "2.3 Checking the WWNs" (page 14) • After completing all the required procedures in this manual, follow the procedures in "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel)" for each OS. FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-...
  • Page 8: Chapter 2 Setting Up The Eternus Dx

    Table 2.2 Transfer rate setting values Transfer rate setting value Fibre Channel card maximum speed 8Gbit/s CA 4Gbit/s CA 8Gbit/s 8Gbit/s 4Gbit/s 4Gbit/s 4Gbit/s 4Gbit/s 2Gbit/s 2Gbit/s 2Gbit/s 1Gbit/s — 1Gbit/s FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2015 FUJITSU LIMITED P3AM-3182-15ENZ0...
  • Page 9: Sense Data Conversion (Setting The Host Responses)

    When setting a Fabric connection, complete the preparatory work and set up the Fibre Channel switch or the CEE/FCoE switch beforehand. For setting details, refer to "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) Fibre Channel Switch Settings", "Converged Enhanced Ethernet Administrator's Guide", or "Fabric OS Administrator's Guide".
  • Page 10: Table 2.5 Host Response Settings

    SAN Boot is configured with the • PRIMEQUEST 1000 series SAN Boot is configured with the • PRIMEQUEST 500/400 series Conditions that are not listed above All parameters Default value FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2015 FUJITSU LIMITED P3AM-3182-15ENZ0...
  • Page 11: Registering The Wwns Of The Accessing Fibre Channel Cards Or Converged Network Adapter Cards (Setting Fc Host)

    For details on the firmware versions that support the Multipath Diagnostic Program, refer to "Multi- • path Diagnostic Program User's Guide". An Oracle-brand Fibre Channel card driver may be used for Fujitsu Fibre Channel cards. To confirm • which driver should be used, check the "Notes" and "Fibre Channel Cards that Require an Oracle-brand Driver"...
  • Page 12: Creating And Allocating Lun Groups (Setting Host Affinity Groups)

    Depending on the OS version, the server may not recognize the ETERNUS DX unless an affinity group is assigned from LUN0. In this case, assign an affinity group starting from LUN0 in ascending order. FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2015 FUJITSU LIMITED...
  • Page 13: Specific Settings

    *1: For a Windows Server 2012 R2, Windows Server 2012, Windows Server 2008 R2, or Windows Server 2008 based WSFC configuration, the reset group settings are not necessary. FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2015 FUJITSU LIMITED P3AM-3182-15ENZ0...
  • Page 14: Setting The Subsystem Parameters (For Hp-Ux Only)

    Note that changing the "Load Balance" setting has no affect on non-HP-UX servers. Checking the WWNs Use ETERNUS Web GUI to check the WWN of each ETERNUS DX. They are required for connecting the ETERNUS DX to the server. FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Copyright 2015 FUJITSU LIMITED P3AM-3182-15ENZ0...
  • Page 15 • operational problems as the result of errors, omissions, or the use of information in this manual. Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information • in this manual.

This manual is also suitable for:

Eternus dx60 s2Eternus dx80Eternus dx90

Table of Contents