1. Manuals
  2. Brands
  3. Mitsubishi Electric Manuals
  4. Air Conditioner
  5. PURY-P72
  6. Service handbook

Mitsubishi Electric PURY-P72 Service Handbook page 97

Hide thumbs Also See for PURY-P72:
Table of Contents
[IV
Remote Controller]
[Operation Procedures]
1. Press the [ON/OFF] button on the remote controller to bring the unit to a stop. The display will appear as shown in the previous page (Normal
display).
2. Press buttons
(CHECK] and
[D~OOb)
simUltaneously for 2 seconds to go into the "Skip-Auto-Mode setting."
under the remote controller function selection mode. Press button@ (SET TEMP. (\7)J or @(SETTEMP. (6.)) to go into the other four modes
under the remote controller function selection mode.
!
Skip-Auto-Mode setting
(Making
the automatic operation mode unselectable)
I
This setting is valid
only
when the controller is connected to the simultaneous cooling/heating type air conditioning units that
support the automatic operation mode.
• "rJ"
blinks
and
either 'ON" or "OFF" fights up on the controller. Pressing the
@)
[TIMER SET (6.) or ( \7)] button switches
between "ON"
and
"OFF."
/. I
I
[TIMER SET (L'l) ((\7))] bUllon
• When set to 'ON," the automatic operation mode is available for selection in the function selection mode.
• When set to 'OFF:' the automatic operation mode is not available for selection in the function selection mode, and an automatic operation
cannot be performed.
(The automatic operation mode is skipped in the function selection mode sequence.)
!
Operation mode display selection mode (Changing the type of display that appears during the automatic mode operationl!
• When connected to the air conditioning units that do not support the automatic operation mode, the setting for this mode is invalid.
•" D"" 0/0"
will blink, and either 'ON"or 'OFF"
will
light up. Press button@[TIMER SET (L'l) or (\7)] in this state to
switch between "ON" and ·OFF."
/. I
<
>
[TIMER SET (L'l) ((\7))] button
I. I
• When it is set to" ON;'
"[I""
0/0"
will appear on the display during automatic operation mode.
• When it is set to" OFF," only"
Cl"
will appear on the display during automatic operation mode.
I
Restricted preset temperature range mode (The range of preset temperature can be changed.)1
1) Temperature range setting for the cooling/dry mode
.. 0/0 ..
will light up in the display window, and the temperature range for the cooling/dry mode will appear on the display.
[Lower limit temperature]: Appears in the preset temperature display window [Upper limit temperature: Appears in the time display window
Switch between the Lower and Upper limit temperature selling by pressing the
[CLOCK-aN-OFF] bUllon. The selected temperature selling blinks.
DO"
I
""I-'
:'s'~
-
30
, .
.
<:
>
[TIMER SET (L'l) (( \7))] bUllon
[The left figure shows the display that appears when the current temperature range setting is between 19"C and 30"C in the Cool/Dry mode,
and the lower limit temperature is selected to be set.)
Press button @)[TIMER SET
(L:;)
or (\7)] to set the lower limit temperature to the desired temperature.
[Sellable range for the lower limit temperature) : 19"C
~
30·C (Settable up to the upper limit temperature that is shown on the display)
[Sellable range for the upper limit temperature] : 30"C
~
19"C (Sellable up to the lower limit temperature that is shown on the display)
2) Temperature range selling for heating
" {)" and the sellable temperature range for heating appear on the display.
As with the Cool/Dry mode, use the
®
[CLOCK-aN-OFF] bullon and the@) [TIMER SET (6.) or (\7)] to set the temperature range.
(Settable range for the lower limit temperature) : 17"C
~
28"C (Sellable up to the upper limit temperature that is shown on the display)
[Setlable range for the upper limit temperature) : 28"C
~
17"C (Sellable up to the lower limit temperature that is shown on the display)
3) Temperature range selling for the automatic mode
When connected to the air conditioning units that do not support the automatic operation mode, the selling for this mode is invalid.
"Cr
and the temperature range for the automatic operation mode appear on the display.
As with the Cool/Dry mode, use the
®
(CLOCK-aN-OFF] bUllon and the@) [TIMER SET
(L:;)
or (\7)] to set the temperature range.
[Sellable range for the lower limit temperature): 19"C
~
28
t
(Sellable up to the upper limit temperature that is shown on the display)
[Setlable range for the upper limit temperature] : 28"C
~
19
t
(Sellable up to the lower limit temperature that is shown on the display)
I
I
DC::
I /.
<;
>
[TIMER SET (6.) (( \7)J bullon
• When set to 'ON," room temperature always appears on the display during operation.
When set to "OFF," room temperature does not appear on the display during operation.
: Room temperature display selection mode (Switching between the display or non-display of room temperature on the controller)
I
• " SS"C " blinks
and either
"ON" or "OFF" lights up on the controller. Pressing the @) [TIMER SET ( 6.) or (\7)] button
switches between "ON" and "OFF."
I
~
•
-P~'f
I
HWE0803A
- 87-
GB
Table of Contents
loading

Related Manuals for Mitsubishi Electric PURY-P72

Related Products for Mitsubishi Electric PURY-P72

This manual is also suitable for:

Pury-p168Pury-p192Pury-p240y(t)shmu-aPury-p96Pury-p120y(t)hmu-aPury-p144

Table of Contents