1. Manuals
  2. Brands
  3. Mitsubishi Electric Manuals
  4. Air Conditioner
  5. PURY-P72
  6. Service handbook

Mitsubishi Electric PURY-P72 Service Handbook page 96

Hide thumbs Also See for PURY-P72:
Table of Contents
[IV Remote Controller
1
(A) To delete group settings
1
,-,
I
,
I
LI
I
I
(B) To delete interlock settings
I
" - - .. will be displayed in the room temperature display window.
- If a transmission error occurs, the selected setting will not be
deleted, and the display will appear as shown below.
In this case, repeat the steps above.
1
,-,
I
I
I
L.f
I
I
I
.. Be"
will be displayed in the room temperature display window.
o
To go back
to
the normal display, follow step
®>.
,n
,I
ILl'
•
(4) Making (A) Group settings and
(8)
Interlock settings
of
a group from any arbitrary remote controller
(A) Group settings and (B) Interlock settings of a group can be made from any
arb~rary
remote controller.
Refer to "(B) Interlock Settings" under section 1"Group Settings/Interlock Settings" for operation procedures.
Set the address as shown below.
(A) To make group settings
Interlocked unit address display window Remote controller address
Indoor unit address display window
The address of the indoor unit to
be
controlled
w~h
the remote controller
(B) To make interlock settings
Interlocked unit address display window LOSSNAY address
Indoor unit address display window
The address of the indoor unit
to
be interlocked with the LOSSNAY
2. Remote controller function selection via the ME remote controller
In the remote controller function selection mode, the seltings for tour types offunctions can be made or changed as neoessary.
I) Skip-Aulo-Mode selling
The automatic operation mode thet is supported by some simultaneous coolingJheating
type
units can be made unselectable via the ME remote
controller.
2) Operation mode display selection mode (Display gr non-djsplay pl COOl/HEAT dyring aytpmatjc operatign mgdel
When the automatic operation mode is selected, the indoor unit will automatically perform a cooling Or heating operation based on the room
temperature. In this case, "
0 ''''0
"or"
0""0"
will appear on the remote controller display.
This selling can be changed so that only"
0"
will appear on the display.
3) Room temperature display seiection mode (Display or non-ctisplay of room temperature)
Allhough
the
suction temperature is normally displayed on the remote controller, the selling can be changed so that it will not appear on the
remote controller.
4) Narrowed preset
temperature
range mode
The default lemperalure ranges are 19°C
10
30°C in lhe cooling/dry mode and HOC
10
:l8°C in the heating mode and 19"C
10
28"C in lhe aulo mode.
By changing these ranges (raising the lower limit for the cooling/dry mode and lowering the upper limll for the heating mode), energy can be saved.
(
NOTE)
When making the temperature range selling on the simultaneous cooIing/heating type units that supports the automatic operation mode to save on
energy consumption, enable the Skip-AutO-Mode selling to make the automatic operation mode unselectable. If the automatic operation mode is
selected, the energy-saving function may not work property.
When connected to the air conditioning unlls that do not support the automatic operation mode. the selting
for
the Skip-Auto-Mode, restricted preset
temperature range mode (AUTO), and operation mode display selection mode are invalid. If an allempt is made to change the preset temperature range,
"LIMIT TEMP." appears on the display.
I
Normal display
I
[Function selection mode sequence on the remote controller]
-
Remote controller function selection mode
J. _ _
Skip-Aulo-Mode settinp
It.f~~
I
OJ
·2(2) t J.
®
Temperature raooe sellino mode AUTOI
I
®
(l)
""
--
~m
o~
(2)tJ.(J)
·1
·1
~
('
10Pnm1lllllle _ _ 1IllIlIe [looIavOfrxMsdarlito_1IllIlIe
_If
6 ' 5
\01.1
®t J.®·2
~~6~fll'
Restricted oreset temoerature ranee mode
CooIinn'
,.,..
®t J.®
""
I
Restricted preset temperature range roode (Heatingl
I
® ®
®t J.®
Room temoerature disolav selection mode
I
I
OJ
[Normal display]
Press and hold the [CHECK] and
[O'foooo] buttons simultaneously
for
two
seconds.
~:
[SET TEMP. (V) ] bulton
@:[SETTEMP(A)]button
"1 : Skip-Auto-Mode is enabled
"2 : Skip-Auto-Mode is disabled
HWE0803A
- 86-
GB
Table of Contents
loading

Related Manuals for Mitsubishi Electric PURY-P72

Related Products for Mitsubishi Electric PURY-P72

This manual is also suitable for:

Pury-p168Pury-p192Pury-p240y(t)shmu-aPury-p96Pury-p120y(t)hmu-aPury-p144

Table of Contents