Toshiba e-studio200l Service Manual

Toshiba e-studio200l Service Manual

Multifunctional digital systems
Hide thumbs Also See for e-studio200l:
Table of Contents
The caption "" was not found. Please press the button below to search within the manual content.

Quick Links

SERVICE HANDBOOK
MULTIFUNCTIONAL DIGITAL SYSTEMS
e-STUDIO200L/202L/230/232/280/282
File No. SHE040003H0
R04022143001-TTEC
Ver08_2006-01
Table of Contents
The caption "" was not found. Please press the button below to search within the manual content.
loading

Summary of Contents for Toshiba e-studio200l

  • Page 1 SERVICE HANDBOOK MULTIFUNCTIONAL DIGITAL SYSTEMS e-STUDIO200L/202L/230/232/280/282 File No. SHE040003H0 R04022143001-TTEC Ver08_2006-01...
  • Page 2 © 2004 TOSHIBA TEC CORPORATION All rights reserved Under the copyright laws, this manual cannot be reproduced in any form without prior written permission of TOSHIBA TEC CORPORATION. No patent liability is assumed, however, with respect to the use of the information contained herein.
  • Page 3 GENERAL PRECAUTIONS REGARDING THE SERVICE FOR e-STUDIO200L/202L/230/232/280/282 SERIES The installation and service should be done by a qualified service technician. 1) Transportation/Installation When transporting/installing the equipment, employ two persons and be sure to hold the posi- tions as shown in the figure.
  • Page 4 Do not allow a short-circuit or do not use the parts not recommended by Toshiba TEC Corporation. 4) Cautionary Labels During servicing, be sure to check the rating plate and cautionary labels such as “Unplug the power cable during service”, “CAUTION.
  • Page 5 5) Disposal of the Equipment, Supplies, Packing Materials, Used Batteries and IC-RAMs Regarding the recovery and disposal of the equipment, supplies, packing materials, used batter- ies and IC-RAMs including lithium batteries, follow the relevant local regulations or rules. Caution: Dispose of used batteries and IC-RAMs including lithium batteries according to this manual. Attention: Se débarrasser de batteries et IC-RAMs usés y compris les batteries en lithium selon ce manuel.
  • Page 7: Table Of Contents

    2.1.3 Error in Internet FAX / Scanning Function.............. 2-10 2.1.4 Printer function error....................2-20 2.2 Self-diagnosis Modes ......................2-22 2.2.1 Input check (Test mode 03) (e-STUDIO200L/230/280).......... 2-24 2.2.2 Input check (Test mode 03) (e-STUDIO202L/232/282).......... 2-31 2.2.3 Output check (test mode 03) .................. 2-39 2.2.4 Test print mode (test mode 04) ................
  • Page 8 3.14 Key Copy Counter (MU-8, MU-10) ..................3-99 3.15 Adjustment of Dogleg ...................... 3-101 4. PREVENTIVE MAINTENANCE (PM)................4-1 4.1 PM Support Mode........................ 4-1 4.1.1 General description ....................4-1 4.1.2 Operational flow and operational screen ..............4-1 e-STUDIO200L/202L/230/232/280/282 CONTENTS June 2004 © TOSHIBA TEC...
  • Page 9 6.2.2 Writing the data to the download jig (PWA-DWNLD-350-JIG) ....... 6-42 6.2.3 K-PWA-DLM-320....................6-44 6.3 Firmware Updating with FSMS (Field Service Manager) (e-STUDIO200L/230/280) ..6-54 6.4 Firmware Updating with USB Storage Device (e-STUDIO200L/230/280)......6-66 6.5 Firmware Updating with USB Storage Device (e-STUDIO202L/232/282)......6-80 6.6 Appendix..........................
  • Page 10 9. DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) ....9-1 10. WIRE HARNESS CONNECTION DIAGRAMS ............10-1 10.1 AC Wire Harness ....................... 10-1 10.2 DC Wire Harness (e-STUDIO200L/230/230L/280/280S) .......... Appendix 10.3 Connector Table (e-STUDIO200L/230/230L/280/280S)..........Appendix 10.4 DC Wire Harness (e-STUDIO202L/232/282)............. Appendix 10.5 Connector Table (e-STUDIO202L/232/282) ..............
  • Page 11: Specifications / Accessories / Options / Supplies

    SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES ERROR CODE AND SELF-DIAGNOSTIC MODE ADJUSTMENT PREVENTIVE MAINTENANCE (PM) TROUBLESHOOTING FIRMWARE UPDATING POWER SUPPLY UNIT REMOTE SERVICE DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) 10. WIRE HARNESS CONNECTION DIAGRAMS...
  • Page 13: Specifications

    SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES Specifications Values in { } are for e-STUDIO200L/202L and values in [ ] are for e- STUDIO280/280S/282/282S in case that the specification is different among e-STUDIO200L/202L, e-STUDIO230/230L/232/232S and e-STUDIO280/280S/282/282S. yCopy process Indirect electrophotographic process (dry)
  • Page 14 {15} 16 [16] {-} - [-] {-} - [-] * Only A4/LT size is available for the LCF. * The tolerance is within ±2. e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA TEC 1 - 2 05/11...
  • Page 15 (25 to 200% when using RADF) yResolution/Gradation....Scanning: 600 dpi x 600 dpi Printing: Equivalent to 2400 dpi x 600 dpi Gradation: 256 steps June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES 1 - 3 05/11...
  • Page 16: Accessories

    Automatic density mode and manual density mode selectable in 11 steps yWeight ........Approximately 75 kg (165.34 lb.): e-STUDIO200L/230/230L/280/280S Approximately 77 kg (169.75 lb.): e-STUDIO202/232/232S/282/282S (include the developer material and drum) (The ADU and Drawer mod- ule are installed.) yPower requirements ....
  • Page 17: Options

    See the figure below (W 637 x D 719 x H 739 (mm)) * When the tilt angle of the control panel is 45 degrees. 4 5 ° 73 9 Fig. 1-1 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES 1 - 5 04/09...
  • Page 18: E-Studio200L/230/230L/280/280S

    SAD: Saudi Arabia IRD: Iran CND: China TWD: Taiwan JPD: Japan KRD: Korea *1: e-STUDIO200L/230/230L/280/280S only *2: In e-STUDIO202L/232/232S/282/282S, 2 discs are included. e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA TEC 1 - 6 05/11...
  • Page 19: Supplies

    The PCI slot (GO-1040) is necessary for installation of the scrambler board (GP-1030) and parallel interface kit (GF-1140). • GM-1030/GM-2030/GM-3030 are exclusive for e-STUDIO200L. They do not operate with e-STUDIO230/230L/280/280S. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES 1 - 7 05/11...
  • Page 20: E-Studio202L/232/232S/282/282S

    1 antenna (GN-3010) can be connected to each. 6. GM-1080U / GM-2080U / GM-4080U are exclusive to e-STUDIO202L. They do not operate with e-STUDIO232/232S/282/282S. e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA TEC 1 - 8...
  • Page 21 Drum OD-1600 Toner cartridge PS-ZT2340 /T/D/C/E Developer D-2340 /C * 1) T: Taiwan D: Asia C: China E: Europe NONE: North America June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES 1 - 9 05/11...
  • Page 22: System List

    System List 1.5.1 e-STUDIO200L/230/230L/280/280S Fig. 1-2 e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA TEC 1 - 10 05/11...
  • Page 23 Scanner upgrade kit GM-3020 GM-3020 GM-3020 GM-3020 GM-3020 Desk MH-1700 MH-1700 MH-1700 MH-1700 MH-1700 Harness kit for coin GQ-1020 GQ-1020 GQ-1020 GQ-1020 GQ-1020 controller June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES 1 - 11 04/09...
  • Page 24 Scanner upgrade kit GM-3020 GM-3020 GM-3020 GM-3020 GM-3020 Desk MH-1700 MH-1700 MH-1700 MH-1700 MH-1700 Harness kit for coin GQ-1020 GQ-1020 GQ-1020 GQ-1020 GQ-1020 controller e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA TEC 1 - 12 04/09...
  • Page 25 Scanner upgrade kit GM-3020 GM-3020 GM-3020 GM-3020 GM-3020 Desk MH-1700 MH-1700 MH-1700 MH-1700 MH-1700 Harness kit for coin GQ-1020 GQ-1020 GQ-1020 GQ-1020 GQ-1020 controller June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES 1 - 13 04/09...
  • Page 26 GM-1020 GM-1020 Scanner upgrade kit GM-3020 GM-3020 GM-3020 GM-3020 Desk MH-1700 MH-1700 MH-1700 MH-1700 Harness kit for coin GQ-1020 GQ-1020 GQ-1020 GQ-1020 controller e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA TEC 1 - 14 04/09...
  • Page 27 GF-1150 Printer/Scanner kit GM-2030 GM-2030 Printer kit GM-1030 GM-1030 Scanner upgrade kit GM-3030 GM-3030 Desk MH-1700 MH-1700 Harness kit for coin GQ-1020 GQ-1020 controller June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES 1 - 15...
  • Page 28: E-Studio202L/232/232S/282/282S

    1.5.2 e-STUDIO202L/232/232S/282/282S Fig. 1-3 e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA TEC 1 - 16 05/11...
  • Page 29 Data overwrite kit GP-1060 GP-1060 GP-1060 GP-1060 GP-1060 Desk MH-1700 MH-1700 MH-1700 MH-1700 MH-1700 Harness kit for coin GQ-1020 GQ-1020 GQ-1020 GQ-1020 GQ-1020 controller June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES 1 - 17 05/11...
  • Page 30 GM-4070 GM-4070 Data overwrite kit GP-1060 GP-1060 GP-1060 GP-1060 Desk MH-1700 MH-1700 MH-1700 MH-1700 Harness kit for coin GQ-1020 GQ-1020 GQ-1020 GQ-1020 controller e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA TEC 1 - 18 05/11...
  • Page 31 Printer/Scanner kit GM-2070 GM-2070 Scanner kit GM-4070 GM-4070 Data overwrite kit GP-1060 GP-1060 Desk MH-1700 MH-1700 Harness kit for coin GQ-1020 GQ-1020 controller June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES 1 - 19 05/11...
  • Page 32 Data overwrite kit GP-1060 GP-1060 GP-1060 GP-1060 GP-1060 Desk MH-1700 MH-1700 MH-1700 MH-1700 MH-1700 Harness kit for coin GQ-1020 GQ-1020 GQ-1020 GQ-1020 GQ-1020 controller e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA TEC 1 - 20 05/11...
  • Page 33 GM-4070 GM-4070 Data overwrite kit GP-1060 GP-1060 GP-1060 GP-1060 Desk MH-1700 MH-1700 MH-1700 MH-1700 Harness kit for coin GQ-1020 GQ-1020 GQ-1020 GQ-1020 controller June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES 1 - 21 05/11...
  • Page 34 Printer/Scanner kit GM-2070 GM-2070 Scanner kit GM-4070 GM-4070 Data overwrite kit GP-1060 GP-1060 Desk MH-1700 MH-1700 Harness kit for coin GQ-1020 GQ-1020 controller e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA TEC 1 - 22 05/11...
  • Page 35 Printer/Scanner kit GM-2080U GM-2080U Scanner kit GM-4080U GM-4080U Data overwrite kit GP-1060 GP-1060 Desk MH-1700 MH-1700 Harness kit for coin GQ-1020 GQ-1020 controller June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES 1 - 23 05/11...
  • Page 36 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA TEC 1 - 24...
  • Page 37: Error Code And Self-Diagnostic Mode

    E190 LCF misfeeding (Paper not reaching the LCF feed P. 5-21 sensor): The paper fed from the LCF does not reach the LCF feed sensor. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 1...
  • Page 38 LCF transport jam (Paper not reaching the 1st P. 5-4 transport sensor): The paper does not reach the 1st transport sensor after it has passed the 2nd trans- port sensor. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 2...
  • Page 39 Paper remaining jam on the transport path: The P. 5-10 paper is remaining on the transport path when print- ing is finished (caused by a multiple paper feeding). June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 3...
  • Page 40 RADF jam access cover open: The RADF jam P. 5-34 access cover has opened during RADF operation. E870 RADF open jam: RADF has opened during RADF P. 5-34 operation. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 4...
  • Page 41 Print end command time-out jam: The printing has P. 5-46 not finished normally because of the communica- tion error between the SYS board and LGC board at the end of printing. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 5...
  • Page 42 Paper remaining on the transport path: The multiple P. 5-14 feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50]). e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 6...
  • Page 43: Service Call

    05-356. C830 Original length sensor adjustment error: The original P. 5-59 length sensor cannot be adjusted normally when per- forming the code 05-356. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 7 05/05...
  • Page 44 [MJ-1022] Alignment motor (rear) abnormality: The alignment motor (rear) is not rotating normally or the rear alignment plate is not moving normally. [MJ-1025] e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 8...
  • Page 45 Database abnormality: Database is not operating nor- P. 5-78 mally. F130 Invaid MAC address P. 5-78 F200 Data overwrite kit (GP-1050/1060) is taken off P. 5-78 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 9...
  • Page 46: Error In Internet Fax / Scanning Function

    2.1.3 Error in Internet FAX / Scanning Function 1) Internet FAX related error (when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280)) (when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282)) Error code Contents Troubleshooting 1C10 System access abnormality P. 5-79...
  • Page 47 2) RFC related error (when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280)) (when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282)) Message displayed in the Error code Contents Troubleshooting TopAccess screen 2500 Syntax error, command unrecog- HOST NAME error (RFC: 500) P.
  • Page 48 P. 5-84 has been exceeded (list Maxi- ments mum) 2BF2 Maximum number of folders has Exceeding maximum number of folders P. 5-84 been exceeded (list Maximum) e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 12...
  • Page 49 4) E-mail related error (when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280)) (when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282)) Message displayed in the Error code Contents Troubleshooting TopAccess screen 2C10 Illegal Job status System access abnormality P. 5-85...
  • Page 50 5) File sharing related error (when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280)) (when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282)) Message displayed in the Error code Contents Troubleshooting TopAccess screen 2D10 Illegal Job status System access abnormality P.
  • Page 51 Troubleshooting TopAccess screen 2DA7 Failed to acquire resource. Resource acquiring failure P. 5-88 2DC0 Job canceled Job canceling 2DC1 Power failure occurred Power failure P. 5-89 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 15...
  • Page 52 6) E-mail reception related error (when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280)) (when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282)) Message displayed in the Error code Contents Troubleshooting TopAccess screen 3A10 MIME Error has been detected in E-mail MIME error P.
  • Page 53 3B42 Decode Error has been detected P. 5-90 in the received mail. This mail could not be transferred to the administrator. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 17...
  • Page 54 3C52 Offramp Destination Error has P. 5-91 been detected in the received mail. This mail could not be trans- ferred to the administrator. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 18...
  • Page 55 The mail could not be 3F10 P. 5-92 received until File I/O is recov- 3F20 P. 5-92 ered. 3F30 P. 5-92 3F40 P. 5-92 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 19 05/11...
  • Page 56: Printer Function Error

    Printer function error Following codes are displayed at the end of the user name on the print job log screen (when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280)) (when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282)) Error code...
  • Page 57 6: Scan/E-mail transmission Primary scanning reproduction ratio (Display in hexadecimal) (Mx256)+(Mx16)+M Secondary scanning reproduction ratio (Display in hexadecimal) (Nx256)+(Nx16)+N Mode 0: Unused 1: Unused 2: Black June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 21...
  • Page 58: Self-Diagnosis Modes

    (Press to display the screen on the control panel at power-ON.) • Test mode (03): Refer to P. 2-24 "2.2.1 Input check (Test mode 03) (e-STUDIO200L/230/280)"/ P. 2-31 "2.2.2 Input check (Test mode 03) (e-STUDIO202L/232/282)" and P. 2-39 "2.2.3 Out- put check (test mode 03)".
  • Page 59 To user State transition diagram of self-diagnosis modes Fig. 2-1 *1 Turn OFF the power after using the self-diagnosis modes, and leave the equipment to the user. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 23...
  • Page 60: Input Check (Test Mode 03) (E-Studio200L/230/280)

    2.2.1 Input check (Test mode 03) (e-STUDIO200L/230/280) The status of each input signal can be checked by pressing the [FAX] button, and the digital keys in the test mode (03). <Operation procedure> [0][3] [START] [FAX] [Digital keys] (LCD ON) [POWER] OFF/ON...
  • Page 61 PFP lower drawer empty sensor No paper Paper present PFP lower drawer tray-up sensor Tray at upper Other than limit position upper limit position June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 25 05/12...
  • Page 62 Bypass feed paper width sensor-0 Refer to table 1 Upper drawer detection switch Drawer not Drawer installed present Upper drawer paper stock sensor Paper almost Paper present empty e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 26 05/11...
  • Page 63 Table 1. Relation between the status of the bypass paper width sensor and paper size (width). Bypass paper-width sensor Paper-width size A3/A4 B5-R A5-R A3/A4 Card size A4-R/A5 B6-R B4-R/B5 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 27 05/11...
  • Page 64 Offset Tray feed sensor (When Offset Tray is installed) Paper present No paper Bypass feed sensor No paper Paper present High-voltage power supply abnormality (shutdown) detec- Normal Abnormal tion e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 28 05/11...
  • Page 65 RADF original width sensor-1 Original No original present RADF original width sensor-2 Original No original present RADF original width sensor-3 Original No original present June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 29 05/11...
  • Page 66 Bridge unit/Job Separator/Offset Tray Highlighting Highlighting Normal display Highlighting connection detection-2 display display display Bridge unit/Job Separator/Offset Tray Normal display Normal display Normal display Highlighting connection detection-1 display e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 30 05/11...
  • Page 67: Input Check (Test Mode 03) (E-Studio202L/232/282)

    Fig. 2-3 Example of display during input check Items to be checked and the condition of the equipment when the buttons [A] to [H] are highlighted are listed in the following pages. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 31 05/12...
  • Page 68 PFP lower drawer empty sensor No paper Paper present PFP lower drawer tray-up sensor Tray at upper Other than limit position upper limit position e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 32 05/11...
  • Page 69 Bypass feed paper width sensor-0 Refer to table 1 Upper drawer detection switch Drawer not Drawer installed present Upper drawer paper stock sensor Paper almost Paper present empty June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 33 05/11...
  • Page 70 Table 1. Relation between the status of the bypass paper width sensor and paper size (width). Bypass paper-width sensor Paper-width size A3/A4 B5-R A5-R A3/A4 Card size A4-R/A5 B6-R B4-R/B5 e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 34 05/11...
  • Page 71 Offset Tray feed sensor (When Offset Tray is installed) Paper present No paper Bypass feed sensor No paper Paper present High-voltage power supply abnormality (shutdown) detec- Normal Abnormal tion June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 35 05/11...
  • Page 72 RADF original width sensor-1 Original No original present RADF original width sensor-2 Original No original present RADF original width sensor-3 Original No original present e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 36 05/11...
  • Page 73 Bridge unit/Job Separator/Offset Tray Highlighting Highlighting Normal display Highlighting connection detection-2 display display display Bridge unit/Job Separator/Offset Tray Normal display Normal display Normal display Highlighting connection detection-1 display June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 37 05/11...
  • Page 74 • It may take some time (2 sec. to 10 sec.) before this check is completed depending on the USB storage device. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 38 05/11...
  • Page 75: Output Check (Test Mode 03)

    [POWER] (Exit) Procedure 3 [POWER] [0][3] Test mode Operation Operation (Code) [START] [START] [CLEAR] OFF/ON [POWER] standby (Exit) Procedure 4 [0][3] [POWER] OFF [START] (Code) [POWER] June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 39...
  • Page 76 Scan motor ON (Automatically stops at limit position; speed can be changed with the [ZOOM] button SLG board cooling fan 1 ON/OFF SLG board cooling fan 2 ON/OFF Scanner exposure lamp ON/OFF e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 40 05/11...
  • Page 77 Power OFF mode (for 200 V series) RADF fan motor ON/OFF Internal cooling fan 2 ON/OFF (low speed) Internal cooling fan 2 ON/OFF (high speed) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 41 05/11...
  • Page 78: Test Print Mode (Test Mode 04)

    Remarks Primary scanning direction 33 gradation steps Error diffusion Secondary scanning direction 33 gradation steps Error diffusion Grid pattern Pattern width: 2 dots, Pitch: 10 mm e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 42...
  • Page 79: Adjustment Mode (05) (E-Studio200L/230/280)

    [INTERRUPT] (Test copy) (Exit) (Key in a value) Stores value [CLEAR] in RAM (Corrects value) [CLEAR] (Corrects value) *Press [FUNCTION CLEAR] to enter minus (-). June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 43 05/12...
  • Page 80 In that case, turn ON the power normally, leave the equipment for approx. 3 minutes after it has become ready state and then start up the adjustment mode again. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC...
  • Page 81 Standby Screen. Code Types of test pattern Remarks Grid pattern Refer to 3.2.3 Printer related adjustment Grid pattern (Duplex printing) Refer to 3.2.3 Printer related adjustment June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 45...
  • Page 82 When the value of secondary scanning <92-164> increases by “1”, the direction image shifts by approx. (scanner section) 0.137 mm toward the trailing edge of the paper. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 46 05/12...
  • Page 83 RADF shifts for double toward the trailing edge sided orig- <0-100> of paper by approx. inal 0.1 mm. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 47...
  • Page 84 <0-255> 0.04%. Drive Fine adjustment of exit PPC/ When the value motor speed <0-255> increases by “1”, the rotation becomes faster by approx. 0.05%. <0-255> e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 48 04/09...
  • Page 85 <0-40> 0.2 mm. Bypass <Acceptable value> feeding <0-15> e-STUDIO230, e-STUDIO280: 0-15 <0-15> e-STUDIO200L, e-STUDIO230L/S, <0-15> e-STUDIO280S: 0-40 Duplex feeding <0-15> June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 49 04/09...
  • Page 86 <0-63> tion section 455-2 Short size (Duplex feed- <0-63> ing/Plain paper) Paper Paper aligning amount feeding adjustment at the registra- <0-63> tion section (LCF/Plain paper) e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 50...
  • Page 87 Paper Paper aligning Long size feeding amount <0-63> adjustment at 464-1 Middle the registra- size <0-63> tion section 464-2 Short size (Bypass feed- <0-63> ing /Envelope) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 51...
  • Page 88 Paper aligning Long size feeding amount <0-63> adjustment at 471-1 Middle the registra- size <0-63> tion section 471-2 Short size (PFP upper <0-63> drawer/Thick paper 1) e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 52...
  • Page 89 When the value adjustment <0-255> increases, the image of Fine adjust- the “light” steps becomes Photo ment of “man- lighter. <0-255> ual density”/ Text Light step <0-255> value June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 53...
  • Page 90 <11-14, background density and 21-24, text density respectively. 31-34, 1: fixed/fixed 41-44> 2: varied/fixed 3: fixed/varied 4: varied/varied Background peak/ Text peak e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 54...
  • Page 91 Adjustment of the smudged/faint <0-9> smudged/faint text. text With decreasing the value, the faint text is suppressed, and with increasing it, the <0-9> smudged text is sup- pressed. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 55...
  • Page 92 Text tion of the background <11-14, density and text density 21-24, respectively. 31-34, 1: fixed/fixed 41-44> 2: varied/fixed 3: fixed/varied 4: varied/varied Background peak/ Text peak e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 56...
  • Page 93 “auto- <0-255> matic density” Image Range correc- Text/Photo When the value tion/Text peak <0-255> decreases, the text adjustment becomes darker. Text <0-255> Photo <0-255> June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 57...
  • Page 94 When the value adjustment <0-255> increases, the image at Fine adjust- the center step becomes Text ment of “man- darker. <0-255> ual density”/ Photo Center value <0-255> e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 58 04/09...
  • Page 95 867-0 Image Sharpness Reproduc- adjustment tion ratio <0-99> (Photo) 40% or smaller 867-1 Reproduc- tion ratio <0-99> 41-80% 867-2 Reproduc- tion ratio <0-99> 81% or larger June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 59...
  • Page 96 When the value tion Mode 1 <0-255> increases, the back- Background ground becomes more Custom peak adjust- brightened. Mode 2 <0-255> ment Custom Mode 3 <0-255> e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 60...
  • Page 97 When the value adjustment Mode 1 <0-255> increases, the image Fine adjust- becomes darker. Custom ment of “auto- Mode 2 <0-255> matic density” Custom Mode 3 <0-255> June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 61 05/05...
  • Page 98 Equipment number (serial When this adjustment is nance number) entry performed with this code, the setting code (08-995) is also performed auto- matically (10 digits). e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 62 05/05...
  • Page 99: Adjustment Mode (05) (E-Studio202L/232/282)

    [INTERRUPT] (Test copy) (Exit) (Key in a value) Stores value [CLEAR] in RAM (Corrects value) [CLEAR] (Corrects value) *Press [FUNCTION CLEAR] to enter minus (-). June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 63 05/12...
  • Page 100 In that case, turn ON the power normally, leave the equipment for approx. 3 minutes after it has become ready state and then start up the adjustment mode again. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC...
  • Page 101 Standby Screen. Code Types of test pattern Remarks Grid pattern Refer to 3.2.3 Printer related adjustment Grid pattern (Duplex printing) Refer to 3.2.3 Printer related adjustment June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 65 05/12...
  • Page 102 When the value of secondary scanning <92-164> increases by “1”, the direction image shifts by approx. (scanner section) 0.137 mm toward the trailing edge of the paper. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 66 05/12...
  • Page 103 RADF shifts for double toward the trailing edge sided orig- <0-100> of paper by approx. inal 0.1 mm. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 67 05/11...
  • Page 104 <0-255> 0.04%. Drive Fine adjustment of exit PPC/ When the value motor speed <0-255> increases by “1”, the rotation becomes faster by approx. 0.05%. <0-255> e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 68 05/11...
  • Page 105 Lower start position paper by approx. drawer <0-40> 0.2 mm. Bypass <Acceptable value> feeding <0-15> e-STUDIO232/282: 0-15 e-STUDIO202L: 0-40 <0-15> <0-15> Duplex feeding <0-15> June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 69 05/11...
  • Page 106 <0-63> tion section 455-2 Short size (Duplex feed- <0-63> ing/Plain paper) Paper Paper aligning amount feeding adjustment at the registra- <0-63> tion section (LCF/Plain paper) e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 70 05/11...
  • Page 107 Paper aligning Long size feeding amount <0-63> adjustment at 464-1 Middle the registra- size <0-63> tion section 464-2 Short size (Bypass feed- <0-63> ing /Envelope) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 71 05/11...
  • Page 108 Paper aligning Long size feeding amount <0-63> adjustment at 471-1 Middle the registra- size <0-63> tion section 471-2 Short size (PFP upper <0-63> drawer/Thick paper 1) e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 72 05/11...
  • Page 109 <0-255> increases, the image of Fine adjust- the “light” steps becomes Photo ment of “man- lighter. <0-255> ual density”/ Text Light step <0-255> value June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 73 05/11...
  • Page 110 <11-14, background density and 21-24, text density respectively. 31-34, 1: fixed/fixed 41-44> 2: varied/fixed 3: fixed/varied 4: varied/varied Background peak/ Text peak e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 74 05/11...
  • Page 111 <0-255> increases, the density in ance the target area becomes 599-1 Image Medium (PCL/Detail) higher. density <0-255> 599-2 Image High density <0-255> June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 75 05/11...
  • Page 112 Adjusts the density level ied image <0-10> of copied image. When the value 667-1 decreases, the text <0-10> becomes lighter. 667-2 <0-10> 667-3 <0-10> 667-4 <0-10> e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 76 05/11...
  • Page 113 <0-255> increases, the image of “light” side becomes lighter. Dark step When the value value <0-255> increases, the image of “dark” side becomes darker. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 77 05/11...
  • Page 114 21-24, the reproduction of the 31-34, background density and 41-44> text density respectively. 1: fixed/fixed 2: varied/fixed 3: fixed/varied 4: varied/varied Background peak/ Text peak e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 78 05/11...
  • Page 115 Image Density Text/Photo When the value adjustment <0-255> increases, the image Fine adjust- becomes darker. Text ment of “auto- <0-255> matic density” Photo <0-255> June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 79 05/11...
  • Page 116 Custom background density and Mode 3 <11-14, text density respectively. 21-24, 1: fixed/fixed 31-34, 2: varied/fixed 41-44> 3: fixed/varied 4: varied/varied Background peak/ Text peak e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 80 05/11...
  • Page 117 Mode 1 <0-4> smudged/faint text. text With increasing the value, the faint text is suppressed, and with decreasing it, the smudged text is sup- pressed. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 81 05/11...
  • Page 118 Equipment number (serial When this adjustment is nance number) entry performed with this code, the setting code (08-995) is also performed auto- matically (10 digits). e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 82 05/11...
  • Page 119: Setting Mode (08) (E-Studio200L/230/280)

    [POWER] OFF/ON [START] [POWER] (Code) *[HELP] (Exit) [INTERRUPT] Sets or (Stores value in RAM) changes value [CLEAR] (Corrects value) * Press [HELP] to enter “-”. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 83 05/12...
  • Page 120 Procedure 14 [CANCEL] [ENTER] [0][8] [Digital key] [Digital key] [POWER] [START] [START] [POWER] (Code) (Sub-code) OFF/ON [INTERRUPT] (Exit) Adjustment value [CLEAR] cannot be changed (Corrects value) e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 84...
  • Page 121 The digit after the hyphen in “Code” of the following table is a sub code. • e-STUDIO200L/230/280: In “RAM”, the NVRAM of the board in which the data of each code is stored is indicated. “M” stands for the LGC board, “SYS” and “UTY”...
  • Page 122 Web power ON UC: 0 1: Language 2 JPN: 5 2: Language 3 <0-6> 3: Language 4 4: Language 5 5: Language 6 6: Language 7 e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 86 05/11...
  • Page 123 <182- 432/140- 297> Paper Paper size (ST-R) feeding/ 216/140 feeding widthwise direction <182- 432/140- 297> Paper Paper size (COMPUTER) 356/257 feeding feeding/widthwise direction <182- 432/140- 297> June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 87...
  • Page 124 JPN: 0 e-STUDIO 280 UC, EUR: 90,000 JPN: 0 Mainte- Current value of PM Counts up when the nance counter Display/0 clearing <8 digits> registration sensor is e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 88...
  • Page 125 (A-Z, a-z, 0- 9) within 10 digits. Network File retention period 0: No limits <0-999> 1 to 999: 1 to 999 days June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 89...
  • Page 126 Internet FAX Internet FAX to be transmitted when creat- ing a template. 0: Not divide 1: 128 2: 512 3: 1024 4: 2048 (Unit: KB) e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 90...
  • Page 127 JPN: 6 4: ST 5: A3 <0 -13> 6: A4 7: A5 8: A6 9: B4 10: B5 11: FOLIO 12: 13”LG 13: 8.5” x 8.5” June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 91...
  • Page 128 Original counter display EUR: 2 Sets whether the origi- interface UC: 0 nal counter is dis- JPN: 0 played or not. <0,2> 0: Not displayed 2: Displayed e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 92...
  • Page 129 (08-352) and the definition setting of 306-6 FOLIO large-sized paper (08- 306-7 353). 306-8 306-9 306-10 306-11 COMP 306-12 13”LG 306-13 8.5” x 8.5” 306-14 306-15 306-16 Others June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 93...
  • Page 130 352) and the definition setting of large-sized 308-6 FOLIO paper (08-353). 308-7 308-8 308-9 308-10 308-11 COMP 308-12 13”LG 308-13 8.5” x 8.5” 308-14 308-15 308-16 Others e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 94...
  • Page 131 (08-352) and the definition setting of 313-6 FOLIO large-sized paper (08- 313-7 353). 313-8 313-9 313-10 313-11 COMP 313-12 13”LG 313-13 8.5” x 8.5” 313-14 313-15 313-16 Others June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 95...
  • Page 132 352) and the definition setting of large-sized 315-6 FOLIO paper (08-353). 315-7 315-8 315-9 315-10 315-11 COMP 315-12 13”LG 315-13 8.5” x 8.5” 315-14 315-15 315-16 Others e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 96...
  • Page 133 Small: Number of output pages other than 321-2 Counter Total set as large-sized <8 digits> paper Total: Total number out- put pages of all paper sizes. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 97...
  • Page 134 Small: Number of output pages other than 327-2 Counter Total set as large-sized <8 digits> paper Total: Total number out- put pages of all paper sizes. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 98...
  • Page 135 Number of output pages other than set as large-sized 330-2 Counter Total paper <8 digits> Total: Total number out- put pages of all paper sizes. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 99 05/05...
  • Page 136 0: Counted as 1 (PM) <0-1> 1: Counted as 2 Counter Count setting of large- 0: Counted as 1 sized paper (PM) <0-1> 1: Counted as 2 e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 100 05/05...
  • Page 137 <8 digits> reset at HDD format- ting. Counter Number of errors in HDD The number of error is (Scanning) <8 digits> reset at HDD format- ting. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 101 04/09...
  • Page 138 <0-12> 2: 150°C 3: 155°C (Side thermistor) 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 102...
  • Page 139 (Center thermistor/Thick 4: 160°C 5: 165°C paper 1) 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 103 04/09...
  • Page 140 4: 150°C 5: 155°C (Plain paper/ 6: 160°C 7: 165°C at ordinary 8: 170°C 9: 175°C 433-1 Side ther- temperature) 10: 180°C mistor <0-12> 11: 185°C 12: 120°C e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 104 04/09...
  • Page 141 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 9 sec. 10: 10 sec. 11: 12 sec. 12: 14 sec. 13: 16 sec. 14: 18 sec. 15: 20 sec. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 105 05/05...
  • Page 142 (driving period of the toner motor) into the developer unit. 0: x1.0 1: x0.75 2: x0.5 3: x0.3 4: x2.0 5: x1.5 e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 106...
  • Page 143 LCF. 468-1 Others (LCF) <0-5> Paper Paper size (Postcard) 148/100 Postcard is sup- feeding feeding/widthwise direction <148- ported only for JPN 432/100- model. 297> June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 107...
  • Page 144 A4 to A4- R, LT-R to LT. “1” is applied when the staple/hole-punch is specified.) Paper Feeding retry setting 0: ON feeding <0-1> 1: OFF e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 108...
  • Page 145 2: 30,000 rpm 3: 25,000 rpm 4: 20,000 rpm 5: 10,000 rpm Laser Polygonal motor rotation in 0: Stopped the energy saving mode <0-1> 1: 10,000 rpm June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 109 04/09...
  • Page 146 2: 150°C 3: 155°C (Side thermistor) 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 110...
  • Page 147 Setting value x 5 sec.: ond drop <0-200> (Center ther- from 0 to 1,000 sec. 525-2 The third mistor) later drop <0-200> 525-3 The fourth drop <0-200> June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 111 05/05...
  • Page 148 <0-10> during printing 537-1 The sec- (Side ther- ond drop <0-10> mistor) 537-2 The third drop <0-10> 537-3 The fourth drop <0-10> e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 112 05/05...
  • Page 149 I/ F printing (USB or par- allel). 1: 1.0 sec. 2: 1.5 sec. -50: 25.5 sec. (in increments of 0.5 sec.) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 113 06/01...
  • Page 150 <0-1> 1: Inner receiving tray User Width setting for image 0: ON interface shift copying (linkage of <0-1> 1: OFF front side and back side) e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 114 05/05...
  • Page 151 0: Cornering 1: Centering User Rotation of paper direction 0: Rotation OFF interface for BOX printing <0-1> 1: Rotation ON June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 115 05/11...
  • Page 152 1: ON (Automatic feeding) Network Auto-forwarding setting of 0: Invalid received FAX <0-1> 1: Valid Network Auto-forwarding setting of 0: Invalid received E-mail <0-1> 1: Valid e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 116 04/09...
  • Page 153 When both are set, each content is dis- played alternately. 0: Not displayed 1: Displayed General Banner advertising display Maximum 27 letters (one-byte character) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 117...
  • Page 154 General Initialization of NIC infor- Returns the value to the mation factory shipping default value. General Performing HDD testing Checks the bad sector. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 118...
  • Page 155 Remote-controlled service 0: Valid (Remote-con- nance function <0-2> trolled server) 1: Valid (L2) 2: Invalid Mainte- Remote-controlled service Maximum 256 Bytes nance HTTP server URL setting June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 119 04/09...
  • Page 156 Maximum 30 letters nance Mainte- HTTP proxy password set- Maximum 30 letters nance ting Mainte- HTTP proxy panel display 0: Valid nance <0-1> 1: Invalid e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 120 04/09...
  • Page 157 Condition number of toner <1-99> (Remote) cartridge Mainte- Automatic ordering sup- 0: OFF nance plies <0-2> 1: Always (Remote) Result table printout 2: ON Error June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 121 04/09...
  • Page 158 1 to 31: 1st to 31st of a Day-2 month Mainte- Remote-controlled service 0: OFF nance polling day selection <0-31> 1 to 31: 1st to 31st of a Day-3 month e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 122 04/09...
  • Page 159 4: 150°C 5: 155°C (OHP film) 6: 160°C 7: 165°C 8: 170°C 9: 175°C 800-1 Side 10: 180°C themistor <0-12> 11: 185°C 12: 120°C June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 123 05/05...
  • Page 160 Main charger bias correc- tion <0-255> (Toner saving mode) Transfer Transfer transformer DC Corrects the value of correction (C) <0-255> the transfer trans- former DC output adjustment (05-221). e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 124 05/05...
  • Page 161 (Photo) <0-255> the developer bias adjustment (05-205). Charger Main charger bias correc- Corrects the value of tion (Normal) <0-255> the main charger bias adjustment (05-210). June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 125 05/05...
  • Page 162 Corrects the value of (Text) <0-255> the laser power adjust- ment (05-286). Laser Laser power correction Corrects the value of (Photo) <0-255> the laser power adjust- ment (05-286). e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 126 05/05...
  • Page 163 3 in HDD Version Version of UI data lan- VXXX.XXX X guage 4 in HDD Version Version of UI data lan- VXXX.XXX X guage 5 in HDD June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 127 05/05...
  • Page 164 1: Enter every time User Clearing timing for files and 0: Immediately after interface Electronic Filing Agent <0-1> the completion of scanning 1: Cleared by Auto Clear e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 128 05/05...
  • Page 165 Raw printing job 0: AUTO (Paper feeding drawer) <0-5> 1: Upper drawer 2: Lower drawer 3: PFP upper drawer 4: PFP lower drawer 5: LCF June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 129 05/05...
  • Page 166 (User Box) Elec- Print mode setting of mixed 0: Image quality prior- tronic Fil- input source of Electronic <0-1> ity mode Filing 1: Function priority mode e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 130...
  • Page 167 Subnet mask 000.000.000.000- 255.255.255.255 (Default value 000.000.000.000) 1010 Network Gateway 000.000.000.000- 255.255.255.255 (Default value 000.000.000.000) 1011 Network Availability of IPX 1: Available <1-2> 2: Not available June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 131 05/05...
  • Page 168 1033 Network Availability of NIC HTTP 1: Available client <1-2> 2: Not available 1034 Network TCP port number to Con- troller HTTP client <1- 65535> e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 132 05/05...
  • Page 169 Maximum 31 letters 1058 Network Login password to FTP Maximum 31 letters server 1059 Network Availability of FTP server 1: Available <1-2> 2: Not available June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 133 05/05...
  • Page 170 Maximum 127 letters 1089 Network Availability of FTP print 1: Available <1-2> 2: Not available 1090 Network Printer user name of FTP print Maximum 31 letters e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 134 05/05...
  • Page 171 Sending mail text of Inter- 0: Invalid (Not sending netFAX <0-1> the mail text) 1: Valid (Sending the mail text) 1117 Network SMB time-out period Unit: Second <1-9999> June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 135...
  • Page 172 5: PFP lower drawer 1136 Network Number of lines simulta- neously connectable when <0-16> using SMB 1137 Network Memory partition size 8-20 M bytes when using Samba <8-20> e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 136 05/11...
  • Page 173 (during printing). When the counter value of the fuser roller is reset, this counter is also reset in sync at the PM support mode. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 137...
  • Page 174 1393 Paper Feeding retry counter Counts the number of feeding (PFP lower drawer) <8 digits> times of the feeding retry from the PFP lower drawer. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 138 05/05...
  • Page 175 3: "00" + "FF" + ran- dom number over- writing (validation 4: "00" + "FF" + ran- dom number over- writing (validation OFF) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 139 05/05...
  • Page 176 "Disable local file save" 0: Function OFF (no function <0-1> restriction on data saving or other operations) 1: Function ON (Data saving or other operations are restricted) e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 140 05/05...
  • Page 177 Setting for "From" address 0: Not permitted edit at "Scan to Email” <0-1> 1: Permitted 1491 Network E-mail domain name 96+2 (delimiter) charac- ASCII sequence only June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 141...
  • Page 178 08-1503 was per- formed. 1518 Pixel Toner cartridge reference Displays the date on counter count started date which 08-1503 was per- formed. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 142 05/12...
  • Page 179 Pixel Average pixel count Displays the average counter (Service technician refer- <0- pixel count in the printer ence) 10000> function and service technician reference. [Unit: 0.01%] June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 143...
  • Page 180 Pixel Latest pixel count Displays the latest pixel counter (Toner cartridge reference) <0- count in the copy func- 10000> tion and toner cartridge reference. [Unit: 0.01%] e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 144...
  • Page 181 FAX func- tion are displayed. 1651-6 30.1-40% <8 digits> [Unit: page] 1651-7 40.1-60% <8 digits> 1651-8 60.1-80% <8 digits> 1651-9 80.1- <8 digits> 100% June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 145...
  • Page 182 When the value of sub-code 3 is changed, the value of sub-code 7 is also updated and vice versa. • When “0” is set at one of sub-codes 0, 3, 6 and 7, the rest of them are automatically updated to “0”. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 146 05/12...
  • Page 183 1250-0 to 8 1251 <Default values of code 1250 (e-STUDIO200L/230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 Sub-code 1: 128,000/148,000/180,000 Sub-code 4: 240,000/240,000/240,000 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 147 05/12...
  • Page 184 Sub-codes 0, 2, 8: 0/0/0 Sub-code 1: 80,000/80,000/80,000 Separation roller 1308-0,1,2,8 1309 <Default values of code 1308 (Lower drawer) (e-STUDIO200L/230/280)> Sub-codes 0, 2, 8: 0/0/0 Sub-code 1: 80,000/80,000/80,000 e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 148 05/12...
  • Page 185 1336-0 to 8 1337 <Default values of code 1336 (e-STUDIO200L/230/280)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 Sub-code 1: 64,000/74,000/90,000 Sub-code 4: 120,000/120,000/120,000 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 149 05/12...
  • Page 186 Key in “1” to copy the value of the total counter (LGC board) (A) onto the value of the backup counter (SYS board) (B). Fig. 2-5 e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 150 05/12...
  • Page 187 Press the [ENTER] button to complete overwriting of the counter value. Note: Note: The screen returns to the code entry screen without copying (overwriting) the value when the [CANCEL] button is pressed. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 151 05/12...
  • Page 188: Setting Mode (08) (E-Studio202L/232/282)

    [POWER] OFF/ON [START] [POWER] (Code) *[HELP] (Exit) [INTERRUPT] Sets or (Stores value in RAM) changes value [CLEAR] (Corrects value) * Press [HELP] to enter “-”. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 152 05/12...
  • Page 189 Procedure 14 [CANCEL] [ENTER] [0][8] [Digital key] [Digital key] [POWER] [START] [START] [POWER] (Code) (Sub-code) OFF/ON [INTERRUPT] (Exit) Adjustment value [CLEAR] cannot be changed (Corrects value) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 153 05/12...
  • Page 190 <0, 6-15> 0: Invalid 6: 3min. 7: 4min. 8: 5min. 9: 7min. 10: 10min. 11: 15min. 12: 20min. 13: 30min. 14: 45min. 15: 60min. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 154 05/12...
  • Page 191 UC: 0 1: Language 2 JPN: 5 2: Language 3 <0-6> 3: Language 4 4: Language 5 5: Language 6 6: Language 7 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 155 05/11...
  • Page 192 297> Paper Paper size (LD) feeding/ 432/279 feeding widthwise direction <182- 432/140- 297> Paper Paper size (LG) feeding/ 356/216 feeding widthwise direction <182- 432/140- 297> e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 156 05/11...
  • Page 193 A telephone number nance phone number <32 dig- can be entered up to 32 its> digits. Use the [Monitor/ Pause] button to enter a hyphen (-). June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 157 05/11...
  • Page 194 0: Valid (The data is printed on A4/A3 when LT/LD is selected or vice versa.) 1: Invalid (The mes- sage to use the selected paper size is displayed.) e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 158 05/11...
  • Page 195 PFP or LCF Paper Paper size setting /LCF EUR: A4 Press the button on the feeding UC: LT LCD to select the size. JPN: A4 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 159 05/11...
  • Page 196 SaveDoc command is completed. The file is not deleted even if the HDD has become full during the exe- cution of command when “1” is set. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 160 06/01...
  • Page 197 2: 300 dpi 3: 400dpi 4: 600 dpi User Default setting of original 0: Text interface mode <0-3> 1: Text/Photo 2: Photo 3: Gray scale June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 161 05/11...
  • Page 198 4: OHP film 5: Tab paper Network Raw printing job 0: Portrait (Paper direction) <0-1> 1: Landscape Network Raw printing job (Staple) 0: Valid <0-1> 1: Invalid e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 162 05/11...
  • Page 199 UC: 0 nal counter is dis- JPN: 0 played or not. <0,2,4> 0: Not displayed 2: Displayed 4: Displayed (Double- sized original is counted as 2.) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 163 05/11...
  • Page 200 306-6 FOLIO large-sized paper (08- 306-7 353). 306-8 306-9 306-10 306-11 COMP 306-12 13”LG 306-13 8.5” x 8.5” 306-14 306-15 306-16 Others e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 164 05/11...
  • Page 201 352) and the definition setting of large-sized 308-6 FOLIO paper (08-353). 308-7 308-8 308-9 308-10 308-11 COMP 308-12 13”LG 308-13 8.5” x 8.5” 308-14 308-15 308-16 Others June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 165 05/11...
  • Page 202 313-6 FOLIO large-sized paper (08- 313-7 353). 313-8 313-9 313-10 313-11 COMP 313-12 13”LG 313-13 8.5” x 8.5” 313-14 313-15 313-16 Others e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 166 05/11...
  • Page 203 352) and the definition setting of large-sized 315-6 FOLIO paper (08-353). 315-7 315-8 315-9 315-10 315-11 COMP 315-12 13”LG 315-13 8.5” x 8.5” 315-14 315-15 315-16 Others June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 167 05/11...
  • Page 204 Number of output pages other than 321-2 Counter Total set as large-sized <8 digits> paper Total: Total number out- put pages of all paper sizes. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 168 05/11...
  • Page 205 Number of output pages other than 327-2 Counter Total set as large-sized <8 digits> paper Total: Total number out- put pages of all paper sizes. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 169 05/11...
  • Page 206 Number of output pages other than set as large-sized 330-2 Counter Total paper <8 digits> Total: Total number out- put pages of all paper sizes. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 170 05/11...
  • Page 207 297> Paper Paper size (Envelope: 235/120 feeding CHO-3-R) <148- feeding/widthwise direction 432/105- 297> Paper Paper size (Envelope: 235/105 feeding YOU-4-R) <148- feeding/widthwise direction 432/105- 297> June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 171 05/11...
  • Page 208 Counts the number of <8 digits> output pages of duplex printing. Counter Counter for RADF Counts the number of <8 digits> originals fed from RADF e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 172 05/11...
  • Page 209 7: C440 8: C450 9: C440 10: C470 11: C470 12: C480 13: C490 14: C470 15: C480 16: C490 17: C470 18: C480 19: C490 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 173 05/11...
  • Page 210 <0-12> 2: 150°C 3: 155°C (Center thermistor) 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 174 05/11...
  • Page 211 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 9 sec. 10: 10 sec. 11: 12 sec. 12: 14 sec. 13: 16 sec. 14: 18 sec. 15: 20 sec. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 175 05/11...
  • Page 212 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 9 sec. 10: 10 sec. 11: 12 sec. 12: 14 sec. 13: 16 sec. 14: 18 sec. 15: 20 sec. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 176 05/11...
  • Page 213 (Side thermistor/Thick 4: 160°C 5: 165°C paper 1) 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 177 05/11...
  • Page 214 (driving period of the toner motor) into the developer unit. 0: x1.0 1: x0.75 2: x0.5 3: x0.3 4: x2.0 5: x1.5 e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 178 05/11...
  • Page 215 Plain Sets the number of feeding number set- paper <0-5> times of the feeding ting retry from the upper 463-1 Others (upper drawer. <0-5> drawer) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 179 05/11...
  • Page 216 Default setting of paper 0: A4/LT 1: LCF feeding source <0-5> 2: Upper drawer 3: Lower drawer 4: PFP upper drawer 5: PFP lower drawer e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 180 05/11...
  • Page 217 Sets the rotational sta- nal motor on standby <0-1> tus of polygonal motor on standby. 0: Rotated (The rota- tional speed is set at 08-490.) 1: Stopped June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 181 05/11...
  • Page 218 <0-1> duction method at photo mode. 0: Error diffusion 1: Dither User Default setting of density 0: Automatic interface adjustment <0-1> 1: Manual (Center) e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 182 05/11...
  • Page 219 (Center thermistor/Enve- 4: 160°C 5: 165°C lope) 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 183 05/11...
  • Page 220 Setting value x 5 sec.: ond drop <0-200> (Side ther- from 0 to 1,000 sec. 527-2 The third mistor) later drop <0-200> 527-3 The fourth drop <0-200> e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 184 05/11...
  • Page 221 JPN: 1 <0-1> User Setting for automatic 0: Invalid interface duplexing mode <0-3> 1: Single-sided to duplex copying 2: Double-sided to duplex copying 3: User selection June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 185 06/01...
  • Page 222 Default setting when mixed 0: Scanned as all in interface size originals are set on <0-1> same size RADF 1: Scanned as each original size e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 186 05/11...
  • Page 223 <0-1> 1: Inner receiving tray User Width setting for image 0: ON interface shift copying (linkage of <0-1> 1: OFF front side and back side) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 187 05/11...
  • Page 224 Image position in editing Sets the page pasted interface <0-1> position for “X in 1” to the upper left corner/ center. 0: Cornering 1: Centering e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 188 05/11...
  • Page 225 1: ON (Automatic feeding) Network Auto-forwarding setting of 0: Invalid received FAX <0-1> 1: Valid Network Auto-forwarding setting of 0: Invalid received E-mail <0-1> 1: Valid June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 189 05/11...
  • Page 226 When both are set, each content is dis- played alternately. 0: Not displayed 1: Displayed General Banner advertising display Maximum 27 letters (one-byte character) e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 190 05/11...
  • Page 227 General Initialization of NIC infor- Returns the value to the mation factory shipping default value. General Performing HDD testing Checks the bad sector. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 191 05/11...
  • Page 228 Remote-controlled service 0: Valid (Remote-con- nance function <0-2> trolled server) 1: Valid (L2) 2: Invalid Mainte- Remote-controlled service Maximum 256 Bytes nance HTTP server URL setting e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 192 05/11...
  • Page 229 HTTP server URL setting Mainte- HTTP proxy setting 0: Valid nance <0-1> 1: Invalid Mainte- HTTP proxy IP address 000.000.000.000- nance setting 255.255.255.255 (Default value 000.000.000.000) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 193 05/11...
  • Page 230 Automatic ordering func- Maximum 100 letters nance tion of supplies (Remote) Supplier's address Mainte- Automatic ordering func- Maximum 128 letters nance tion of supplies (Remote) Notes e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 194 05/11...
  • Page 231 Setting total counter trans- nance mission interval (Remote) (Hour/Hour/Minute/Minute) Mainte- Destination E-mail address Maximum 192 letters nance (Remote) Mainte- Destination E-mail address Maximum 192 letters nance (Remote) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 195 05/11...
  • Page 232 Sets where the end of period end <0-3> the trial period is to be notified. 0: OFF 1: User 2: Service center 3: User and service center e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 196 05/11...
  • Page 233 3: 145°C limit 4: 150°C 5: 155°C (Envelope) 6: 160°C 7: 165°C 8: 170°C 9: 175°C 804-1 Side 10: 180°C themistor <0-12> 11: 185°C 12: 120°C June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 197 05/11...
  • Page 234 <0-3> temperature/humidity. 0: All valid 1: All invalid 2: Valid only in auto- toner sensor 3: All valid except transfer and separa- tion e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 198 05/11...
  • Page 235 Corrects the value of (Normal) <0-255> the laser power adjust- ment (05-286). Laser Laser power correction Corrects the value of (Text/Photo) <0-255> the laser power adjust- ment (05-286). June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 199 05/11...
  • Page 236 UI data fixed section ver- VXXX.XXX X sion Version UI data common section VXXX.XXX X version Version Version of UI data lan- VXXX.XXX X guage 1 in HDD e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 200 05/11...
  • Page 237 1: Forced start-up (Not recovered) 2: Forced start-up (Recovered) User Access code entry for 0: Renewed automati- interface Electronic Filing printing <0-1> cally 1: Enter every time June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 201 05/11...
  • Page 238 Raw printing job 0: AUTO (Paper feeding drawer) <0-5> 1: Upper drawer 2: Lower drawer 3: PFP upper drawer 4: PFP lower drawer 5: LCF e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 202 05/11...
  • Page 239 (User Box) Elec- Print mode setting of mixed 0: Image quality prior- tronic Fil- input source of Electronic <0-1> ity mode Filing 1: Function priority mode June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 203 05/11...
  • Page 240 Availability of IPX 1: Available <1-2> 2: Not available 1012 Network Network frame type 1: Automatic <1-5> 2: IEEE802.3 3: Ethernet II 4: IEEE802.3SNAP 5: IEEE802.2 e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 204 05/11...
  • Page 241 65535> 1037 Network Availability of SMTP client 1: Available <1-2> 2: Not available 1038 Network FQDN or IP address to Maximum 128 Bytes SMTP server June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 205 05/11...
  • Page 242 Maximum 31 letters munity 1067 Network Authentication TRAP func- 1: Valid tion <1-2> 2: Invalid 1068 Network ALERTS TRAP function 1: Valid <1-2> 2: Invalid e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 206 05/11...
  • Page 243 <1- 65535> 1093 Network Login name to Novell print MFP_ Maximum 47 letters server serial The Network-related serial number of the equipment appears at “serial“ June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 207 05/11...
  • Page 244 Sending mail text of Inter- 0: Invalid (Not sending netFAX <0-1> the mail text) 1: Valid (Sending the mail text) 1117 Network SMB time-out period Unit: Second <1-9999> e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 208 05/11...
  • Page 245 1135 Paper Default setting of drawers 1: LCF feeding (Printer/BOX) <1-5> 2: Upper drawer 3: Lower drawer 4: PFP upper drawer 5: PFP lower drawer June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 209 05/11...
  • Page 246 PM support mode. 1376 Counter Toner cartridge drive Counts the rotation counter <8 digits> number of the toner cartridge. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 210 05/11...
  • Page 247 ON. When the counter value of the fuser roller is cleared, this counter value is also cleared in sync at PM support mode. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 211 05/11...
  • Page 248 <8 digits> registration sensor is When the counter value of the fuser roller is reset, this counter is reset in sync at the PM support mode. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 212 05/11...
  • Page 249 2: In both same direc- tion and different directions 1432 Network Mode only for Private Print 0: Normal mode <0-1> 1: Mode for Private Print June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 213 05/11...
  • Page 250 IPP jobs. 1448 Network IPP administrator pass- This should be the word password of an account which can control all IPP jobs. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 214 05/11...
  • Page 251 Display of paper size set- JPN: 0 0: Not displayed interface ting by installation opera- UC: 1 1: Displayed tion of drawers EUR: 0 <0-1> June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 215 05/11...
  • Page 252 LG for single-size docu- <0-1> 1: Enabled ment 1494 General Limitation check method 0: Checked at every <0-1> page printed 1: Checked at every job printed e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 216 05/11...
  • Page 253 Counts the number of Duplex <8 digits> output pages using printing [4IN1]. 1530-4 4-UP / Counts the number of Simplex <8 digits> sheets using [4IN1]. printing June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 217 05/11...
  • Page 254 Wireless LAN driver 1: Off 2: Max Sleep mode setting <1-3> 3: Normal 1675 Wireless Wireless LAN driver 1: Long 2: Short Slot-time limitation <1-2> e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 218 05/11...
  • Page 255 The EAP authentica- Holding interval <60- tion will start after hav- 65535> ing been waited in this period when an EAP failure was received. 60: 60 seconds June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 219 06/01...
  • Page 256 Wireless Wireless LAN supplicant This setting is whether Ethereal log file output <1-2> the Ethereal log file is output or not. 1: NO 2: YES e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 220 06/01...
  • Page 257 1: Security function 1714 Blue- Bluetooth 0000 Maximum 8 digits tooth (8-digit sequence) This setting is valid only when the bluetooth security function is ON. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 221 05/11...
  • Page 258 (Minimum area 4) 255.255.255.255 (Default value: 000.000.000.000) 1727 Network IP address range for IP fil- IP filter maximum area (Maximum area 4) 000.000.000.000- 255.255.255.255 (Default value: 000.000.000.000) e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 222 05/11...
  • Page 259 (Minimum area 9) 255.255.255.255 (Default value: 000.000.000.000) 1737 Network IP address range for IP fil- IP filter maximum area (Maximum area 9) 000.000.000.000- 255.255.255.255 (Default value: 000.000.000.000) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 223 05/11...
  • Page 260 Enabling server's IP Domain Name Server address acquired by DHCP <1-2> option (6) 1: Enabled 2: Disabled This value is used only when DHCP is enabled. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 224 05/11...
  • Page 261 Wireless LAN supplicant Maximum 63 letters Path name for user certifi- cate 1766 Wireless Wireless LAN supplicant Maximum 63 letters Path name entered for CA self-certificate June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 225 05/11...
  • Page 262 "Save as file" and Email transmission. 0: [FileName]-[Data]- [Page] 1: [FileName]-[Page]- [Data] 2: [Data]-[FileName]- [Page] 3: [Data]-[Page]-[File- Name] 4: [Page]-[FileName]- [Data] 5: [Page]-[Data]-[File- Name] e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 226 05/11...
  • Page 263 1915 Network Filing size for Network 0: Eliminates 2 mm scanning function <0-1> from circumference (Void: 2 mm) 1: No space eliminated (Void: 0 mm) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 227 05/11...
  • Page 264 2: QWERTZ layout 3: AZERTY layout 1935 User Keyboard layout for Lan- 1: QWERTY layout interface guage 7 <0-2> (for Europe) 2: QWERTZ layout 3: AZERTY layout e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 228 05/11...
  • Page 265 BDC2 of user authentica- Maximum 128 letters tion 1956 Network PDC3 of user authentica- Maximum 128 letters tion 1957 Network BDC3 of user authentica- Maximum 128 letters tion June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 229 05/11...
  • Page 266 1958 Network PDC of device authentica- Maximum 128 letters tion 1959 Network BDC of device authentica- Maximum 128 letters tion e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 230 05/11...
  • Page 267 08-1503 was per- formed. 1518 Pixel Toner cartridge reference Displays the date on counter count started date which 08-1503 was per- formed. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 231 05/12...
  • Page 268 Average pixel count Displays the average counter (Service technician refer- <0- pixel count in the printer ence) 10000> function and service technician reference. [Unit: 0.01%] e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 232 05/11...
  • Page 269 Latest pixel count Displays the latest pixel counter (Toner cartridge reference) <0- count in the copy func- 10000> tion and toner cartridge reference. [Unit: 0.01%] June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 233 05/11...
  • Page 270 FAX func- tion are displayed. 1651-6 30.1-40% <8 digits> [Unit: page] 1651-7 40.1-60% <8 digits> 1651-8 60.1-80% <8 digits> 1651-9 80.1- <8 digits> 100% e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 234 05/11...
  • Page 271 When the value of sub-code 3 is changed, the value of sub-code 7 is also updated and vice versa. • When “0” is set at one of sub-codes 0, 3, 6 and 7, the rest of them are automatically updated to “0”. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 235...
  • Page 272 1250-0 to 8 1251 <Default values of code 1250 (e-STUDIO202L/232/282)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 Sub-code 1: 128,000/148,000/180,000 Sub-code 4: 240,000/240,000/240,000 e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 236 05/12...
  • Page 273 Sub-codes 0, 2, 8: 0/0/0 Sub-code 1: 80,000/80,000/80,000 Separation roller 1308-0,1,2,8 1309 <Default values of code 1308 (Lower drawer) (e-STUDIO202L/232/282)> Sub-codes 0, 2, 8: 0/0/0 Sub-code 1: 80,000/80,000/80,000 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 237 05/11...
  • Page 274 1336-0 to 8 1337 <Default values of code 1336 (e-STUDIO202L/232/282)> Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 Sub-code 1: 64,000/74,000/90,000 Sub-code 4: 120,000/120,000/120,000 e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 238 05/11...
  • Page 275 Key in “1” to copy the value of the total counter (LGC board) (A) onto the value of the backup counter (SYS board) (B). Fig. 2-8 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 239...
  • Page 276 Press the [ENTER] button to complete overwriting of the counter value. Note: Note: The screen returns to the code entry screen without copying (overwriting) the value when the [CANCEL] button is pressed. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 240...
  • Page 277: Pixel Counter

    This function enables you to know how each user uses the equipment and to grasp the tendency of toner consumption (number of output pages per cartridge). June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 241...
  • Page 278 Manual Manual Manual TEXT PHOTO density density density density density density /PHOTO Center Original mode Density setting Fig. 2-10 Factors affecting toner consumption and the tendency e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 242...
  • Page 279 “1.49” is added to the print count when printing on B4 size. (area ratio to A4: 149%) “1.27” is added to the print count when printing on LG size. (area ratio to LT: 127%) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 243 05/05...
  • Page 280 The average value of all pixel count data after each reference data is cleared is calculated and displayed. Latest pixel count (%) The value is displayed for printing just before the pixel counter is confirmed. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 244 05/05...
  • Page 281 08-1502: All information related to the service technician reference pixel count is cleared. 08-1503: All information related to the toner cartridge reference pixel count is cleared. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 245 05/05...
  • Page 282 The relation between pixel count and number of output pages per cartridge is as follows: Standard number of output pages X/10 6% 12% Pixel count (%) Fig. 2-11 Pixel count and number of output pages per cartridge e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 246 05/05...
  • Page 283 Fig. 2-12 Information screen of toner cartridge reference The following screen is displayed when the service technician reference is selected in the setting mode (08-1505). Fig. 2-13 Information screen of service technician reference June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 247...
  • Page 284 Average Pixel Count [%] 20040711 12345 23456 12345 45678 Latest Pixel Count [%] 20040711 12345 23456 12345 45678 Fig. 2-15 Data list of service technician reference e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 248...
  • Page 285 Display in the setting mode (08) Information of pixel count can be also checked in the setting mode (08). For details, see P. 2-83 "2.2.7 Setting mode (08) (e-STUDIO200L/230/280)"/ P. 2-152 "2.2.8 Setting mode (08) (e-STUDIO202L/232/282)". Print count, pixel count...
  • Page 286 The date (08-1502 was performed) is stored. Toner cartridge reference cleared date The toner cartridge reference cleared date is displayed. The date (08-1503 was performed) is stored. e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 250...
  • Page 287: Classification List Of Adjustment Mode (05) / Setting

    [Smudged/Faint text] 653, 654, 655, 928 [Printer density] 667-0 to 4, 672-0 to 4, 676-0 to 4 [Binarizing] 700, 701, 702 Drive [Main motor] 421, 422 [Exit motor] 424, 425 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 251 05/12...
  • Page 288 [Switchback] 462 [Sensors/EEPROM] 356, 367, 368 [Transporting] 357, 358, 365, 366 Finisher [Folding / Binding position] 468-0 to 2 [Tray reset] 648 [Cascade] 652, 653 e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 252 05/11...
  • Page 289 924, 925, 926, 927, 928, 929, 930, 931, 933, 934, 935, 936, 937, 938, 939, 944 [Engine firmware] 903, 905, 907, 908 [FAX] 915 [NIC] 916 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 253 05/11...
  • Page 290 [Data overwrite kit] 633 [Equipment number] 995 [Toner recycle] 838 [Machine identification information] 477 [Temperature/humidity] 839 [Initialization] 947 [Mode setting] 949 [Template] 1140 [NVRAM] 1427 [SRAM] 1428 e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 254 05/11...
  • Page 291 [Keyboard layout] 1929, 1930, 1931, 1932, 1933, 1934, 1935 Scanner [Position] 305, 306 [Distortion] 308 [Reproduction ratio] 340 [Carriage position] 359 [Shading position] 350, 351 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 255 05/12...
  • Page 292 3, 535, 536-0 to 3, 537-0 to 3, 800-0 to 1, 801- 0 to 1, 802-0 to 1, 803-0 to 1, 804-0 to 1, 886, 896-0 to 1 [Pre-running] 417, 439, 440, 441, 523, 526 e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 256 05/11...
  • Page 293 1922, 1925, 1937, 1943, 1954, 1955, 1956, 1957 [PDC] 1121 [BDC] 1122 [NT domain] 1123 [Address book] 1125, 1476, 1477 [Netware] 1128, 1129, 1134, 1143, 1144, 1148 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 257 05/11...
  • Page 294 [System firmware] 900, 920, 921, 922, 923, 924, 925, 926, 927, 928, 929, 930, 931, 933, 934, 935, 936, 937, 938, 939, 944 [Engine firmware] 903, 905, 907, 908 [FAX] 915 e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 258 05/11...
  • Page 295 [User data management] 1472, 1473, 1474, 1481, 1482, 1483 [Limitation check] 1494 [e-Filing Access Mode] 1497 [Inbound FAX] 1498 [Administrator's password] 1778 [FAX reception] 1926 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 259 05/11...
  • Page 296 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 260...
  • Page 297: Adjustment

    B indicates the output voltage of the auto-toner sensor (2.30 V in the above case). The drum, developer unit, etc. are in operation. • C indicates the latest adjustment value. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 1...
  • Page 298 Press the [ENTER] or [INTERRUPT] button. The drum, developer unit, etc. are stopped and the following is displayed. 100% [ENTER] TEST MODE [INTERRUPT] Fig.3-5 Turn the power OFF. (10) Install the toner cartridge. e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 2...
  • Page 299: Image Dimensional Adjustment

    (c) Image location of primary scanning direction (d) Reproduction ratio of secondary scanning direc- tion (e) Image location of secondary scanning direction (f) Top margin (g) Right margin (h) Bottom margin June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 3...
  • Page 300 Wait Warming Up If the test copy does not satisfy the specified values, 100% return to step 1 and COPYING repeat the adjustment procedure. Power OFF/ON : Exit the Adjustment Mode. Fig.3-6 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 4...
  • Page 301: Paper Alignment At The Registration Roller

    [START] (Sub-code) [START] displayed value [Power] [SET] or [POWER] [Drawer (*4) +[FAX] [INTERRUPT] OFF/ON selection] (Test print) Stores in memory (Exit) (*4) 1: Single-sided grid pattern 3: Double-sided grid pattern June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 5...
  • Page 302 So, when adjusting the aligning amount, try to choose the appropriate amount while confirming the leading edge position is not shifted. * As a tentative countermeasure, the service life of the feed roller can be extended by increas- ing the aligning amount. e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 6...
  • Page 303: Printer Related Adjustment

    Æ “100% A” is displayed Æ Press [1] Æ [FAX] Æ (A grid pattern is printed out.) *The larger the adjustment value is, the longer the distance B becomes (approx. 0.05 mm/step). June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 7...
  • Page 304 Æ “100% A” is displayed Æ Press [1] Æ [FAX] Æ (A grid pattern is printed out.) *The larger the adjustment value is, the longer the distance C becomes (approx. 0.125 mm/step). e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 8 04/09...
  • Page 305 Æ “100% A” is displayed Æ Press [1] ([3] for duplexing)Æ [FAX] Æ (A grid pattern is printed out.) *The larger the adjustment value is, the longer the distance D becomes (approx. 0.4 mm/step). June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 9...
  • Page 306 Æ “100% A” is displayed Æ Press [3] Æ [FAX] Æ (A grid pattern is printed out.) *The larger the adjustment value is, the longer the distance E becomes (approx. 0.05 mm/step). e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 10 04/09...
  • Page 307 05-441 (Lower drawer, A3/LD), 440 (Upper drawer, A4/LT), 444 (PFP, A4/LT), 443 (LCF, A4/LT), 442 (Bypass feed, A4/LT), 445 (Duplexing, A3/LD) Æ 52±0.5 mm(0.4 mm/step) 05-498-0 (Lower drawer, A3/LD), Æ 52±0.5 mm (0.05 mm/step) 498-1 (Upper drawer, A4/LT) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 11 04/09...
  • Page 308: Scanner Related Adjustment

    When the adjustment (05-421) is performed, the same adjustment for FAX (05-422) is automati- cally and consecutively performed. 3.2.4 Scanner related adjustment Image distortion Feeding direction Step 1 Feeding direction Step 2 Fig.3-9 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 12 05/05...
  • Page 309 Loosen the mirror-1 adjustment screw (CCW). Apply the screw locking agents to the adjust- ment screws. (2 areas) Carriage-1 • Recommended screw lock agent Manufacturer: Three Bond Product name: 1401E Fig.3-11 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 13...
  • Page 310 *The larger the adjustment value is, the higher the reproduction ratio and the longer the distance A become (approx. 0.125 mm/step). Copied image of the ruler Feeding direction Fig.3-12 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 14 04/09...
  • Page 311 *The smaller the adjustment value is, the more the image is shifted to the left and the distance B becomes narrower (0.085 mm/step). Copied image of the ruler Feeding direction Fig.3-13 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 15 04/09...
  • Page 312 Æ Press the [ENTER] or the [INTERRUPT] button (stored in memory). Æ (“100% A” is displayed.) *The smaller the adjustment value is, the lower the reproduction ratio becomes (0.45 mm/step). Copied image of the ruler Feeding direction Fig.3-14 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 16 04/09...
  • Page 313 Æ (“100% A” is displayed.) *The larger the adjustment value is, the more the image is shifted to the trailing edge (0.14 mm/ step). Copied image of the ruler Feeding direction Fig.3-15 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 17 04/09...
  • Page 314 Æ Press the [ENTER] or the [INTERRUPT] button (stored in memory). Æ (“100% A” is displayed.) *The larger the adjustment value is, the wider the blank area becomes (approx. 0.04 mm/step). Feeding direction Fig.3-16 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 18 04/09...
  • Page 315 Æ Press the [ENTER] or the [INTERRUPT] button (stored in memory). Æ (“100% A” is displayed.) *The larger the adjustment value is, the wider the blank area at the right side becomes (approx. 0.04 mm/step). Feeding direction Fig.3-17 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 19 04/09...
  • Page 316 Æ Press the [ENTER] or the [INTERRUPT] button (stored in memory). Æ (“100% A” is displayed.) *The larger the adjustment value is, the wider the blank area at the trailing edge becomes (approx. 0.04 mm/step). Feeding direction Fig.3-18 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 20 04/09...
  • Page 317: Image Quality Adjustment (Copying Function)

    Press the [ENTER] or [INTERRUPT] button to store the value. Æ The equipment goes back to the ready state. Let the equipment restarted and perform copying job. If the desired image density has not been attained, repeat step (2) to (5). June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 21...
  • Page 318: Gamma Slope Adjustment

    00: Use default value * The values in “( )” are the adjustment codes of the Custom Mode. <Procedure> Procedure is same as that of P.3-21 "3.3.1 Density adjustment". e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 22...
  • Page 319: Sharpness Adjustment

    Make a test copy and compare the image obtained with the current settings; if necessary, make adjust- ment using the following procedure. <Procedure> Procedure is same as that of P.3-21 "3.3.1 Density adjustment". June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 23...
  • Page 320: Setting Range Correction

    Make a test copy and compare the image obtained with the current settings; if necessary, make adjust- ment using the following procedure. <Procedure> Procedure is same as that of P.3-21 "3.3.1 Density adjustment". e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 24...
  • Page 321: Adjustment Of Smudged/Faint Text

    The larger the value is, the density of the item to be 596-1 597-1 598-1 599-1 Medium density adjusted becomes darker. Acceptable values: 596-2 597-2 598-2 599-2 High density 0 to 255. (Default: 128) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 25 05/11...
  • Page 322: Adjustment Of Image Density

    For resetting the value, repeat step (2) to (5). Turn the power OFF and then back ON to perform printing job. If the desired image density has not been attained, repeat step (2) to (7). e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 26 04/09...
  • Page 323: Image Quality Adjustment (Printing Function)

    Press the [ENTER] or [INTERRUPT] button to store the value. The equipment goes back to the ready state. Turn the power OFF and then back ON to perform printing job. If the desired text density has not been attained, repeat step (2) to (5). June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 27...
  • Page 324: Adjustment Of Image Density

    For resetting the value, repeat step (2) to (5). Turn the power OFF and then back ON to perform printing job. If the desired image density has not been attained, repeat step (2) to (7). e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 28...
  • Page 325: Image Quality Adjustment (Scanning Function)

    Press the [ENTER] or [INTERRUPT] button to store the value. The equipment goes back to the ready state. Turn the power OFF and then back ON to perform scanning job. If the desired image density has not been attained, repeat step (2) to (5). June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 29...
  • Page 326: Sharpness Adjustment

    For resetting the value, repeat step (2) to (5). Turn the power OFF and then back ON to perform scanning job. If the desired image density has not been attained, repeat step (2) to (7). e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 30...
  • Page 327: Setting Range Correction

    The setting conditions possible are as follows: Background peak Text peak 1: fixed fixed 2: varied fixed 3: fixed varied 4: varied varied <Procedure> Procedure is same as that of P.3-29 "3.5.1 Density adjustment". June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 31...
  • Page 328: Setting Range Correction (Adjustment Of Background Peak)

    * The image changes slightly in text mode because it is treated as a simple binary format image. <Procedure> Procedure is same as that of P.3-29 "3.5.1 Density adjustment". e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 32 04/09...
  • Page 329: Adjustment Of High-Voltage Transformer

    Note Refer to P.3-36 "[B] Refer to P.3-36 "[C] Refer to P.3-37 "[D] Con- Connection for devel- Connection for main nection for transfer/separation oper bias adjustment". charger adjustment". charger adjustment". June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 33...
  • Page 330 Be careful not to let the connector and the harness be caught. High-voltage transformer jig Fig.3-20 Fix the green cable of the high-voltage trans- former jig to the frame of the equipment. Screw Green cable Fig.3-21 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 34 04/09...
  • Page 331 Install the door switch jig. Close the transfer cover. Front cover opening/closing switch Door switch jig Fig.3-22 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 35...
  • Page 332 Ground to the machine frame ( green cable ) ( + ) terminal: ( - ) terminal: Connect with the Connect with the white cable red cable ( thick line ) Fig.3-24 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 36...
  • Page 333 Ground to the machine frame ( green cable ) ( + ) terminal: ( - ) terminal: Connect with the red cable ( thin line ) Connect with the white cable Fig.3-25 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 37...
  • Page 334 Adjustment value -566±72mV -566±72mV -391±36mV [SET] : Adjusted value “YYY” is stored in memory. [INTERRUPT] 100% TEST MODE Return to 1 to enter the other adjustment code. [POWER] : OFF/ON Fig.3-26 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 38...
  • Page 335: Precautions

    The adjustment code varies according to where blotched image and poor transfer occur. Select the required adjustment code while referring to the following diagram. Approx. 11mm Approx. 5mm Adjustment code "220" "221" "222" Leading edge Trailing edge area of paper area of paper Fig.3-27 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 39...
  • Page 336 Approx. 35mm Approx. 48mm Adjustment code "233" "235" "234" "235" Leading edge Trailing edge area of paper area of paper Fig.3-28 * Adjustment code 235 performs the adjustment for 2 areas. e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 40...
  • Page 337: Adjustment Of The Scanner Section

    Adjustment of the carriage wire tension is not necessary since a certain tension is applied to the car- riage wires by the tension springs. Note: Note: Make sure the tension applied to the wire is normal. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 41...
  • Page 338 Loosen the screws fixing the front side pulley bracket, make the sections A and B of the carriage- 2 touch with the inside of the exit side frame and screw them up. Carriage-2 Pulley bracket [Rear] [Front] Exit side frame Fig.3-31 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 42...
  • Page 339 Note: Note: Make sure that the sections A and B of the carriage-2 touch with the exit side frame. Carriage-1 [Rear] [Front] Exit side frame Bracket Bracket Fig.3-32 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 43...
  • Page 340 Each turn should be pushed against the previously wound turn so that there is no space between them. 4 turns 4 turns 2 turns 2 turns Ball terminal Ball terminal No space between turns Hook Hook Color: Silver Color: Black [Rear] [Front] Fig.3-33 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 44...
  • Page 341 When the wire holder jig is attached, make sure that the wire is not shifted or loosened. • The wire should come out of the slot of the wire holder jig and be passed through between the arm and the jig. Wire holder jig Fig.3-34 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 45...
  • Page 342: Lens Unit

    When replacing the unit, do not loosen or remove the 4 screws indicated with the arrows. Fig.3-35 • Handle the unit with care. Do not hold the lens and adjusted part (hold the unit as shown below). Fig.3-36 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 46...
  • Page 343 If each mark on the rulers differs, perform the adjustment with the following procedures. <Procedure> Take off the original glass and lens cover. Loosen 2 screws fixing the lens unit. Screw Lens unit Fig.3-38 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 47...
  • Page 344 Attach the lens cover and original glass. Make a copy to confirm the reproduction ratio. Repeat the procedure 1 to 5 until the marks on the copied ruler and actual ruler match. e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 48...
  • Page 345: Adjustment Of The Paper Feeding System

    2) Move the entire guide to the front or rear side. 2) Move the entire guide to the front or rear side. 3) Tighten the screw. 3) Tighten the screws. ( B ) ( A ) Fig.3-42 Fig.3-43 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 49 05/07...
  • Page 346: Adjustment Of Developer Unit

    Fig.3-44 Turn the adjustment screw to widen the gap Screw so that the jig can be inserted in it. (Turning the screw clockwise widens the gap) Fig.3-45 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 50...
  • Page 347 “0.50” cannot be inserted into the gap. Developer sleeve Fig.3-47 Confirm that the side seals are attached on the toner scattering prevention sheet. Side seal Toner scattering prevention sheet Fig.3-48 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 51...
  • Page 348 Attach the developer material cover and Developer tighten 2 screws. material cover Note: Note: After the developer material has been replaced, adjust the auto-toner sensor. (See P.3-1 "3.1 Adjustment of Auto-Toner Sensor".) Fig.3-49 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 52...
  • Page 349: Adjustment Of The Radf (Mr-3016)

    If they do not, adjust them according to the following procedure. Fig.3-51 Loosen the stepped screw 1 turn and 2 screws on the adjustment plate a half turn (status of temporary fixing). Half turn 1 turn Fig.3-52 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 53...
  • Page 350 RADF. While peering inside from the front side, fit the posi- tions of the pin and hole by moving the RADF right and left. Fig.3-55 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 54...
  • Page 351 Fig.3-57 Open the RADF to tighten 2 hand screws. Close the RADF and then check again that the positioning pins fit smoothly into the holes on the RADF. Fig.3-58 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 55...
  • Page 352 Align the platen sheet against the left and rear side of the original glass. Close the RADF slowly. Open the RADF to check that the platen sheet is correctly attached. Fig.3-61 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 56...
  • Page 353: Adjustment Of Radf Height

    Adjust the height by turning the height adjusting screw on the right hinge. CW: The height of the hinge becomes high. CCW: The height of the hinge becomes low. Fig.3-63 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 57...
  • Page 354 Adjust the height by turning the height adjusting screw on the left hinge. CW: The height of the hinge becomes high. CCW: The height of the hinge becomes low. Fig.3-64 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 58...
  • Page 355: Adjustment Of Skew

    Adjustment of aligning"). Case B: Adjust the aligning adjustment position to the rear side “+” of the original ( P.3-62 "3.10.5 Adjustment of aligning"). White arrow: feeding direction Paper Original Fig.3-65 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 59...
  • Page 356 "3.10.6 Adjustment of aligning at reversing"). Case F: Adjust the reverse aligning adjustment position to the rear side “+” of the original ( P.3-63 "3.10.6 Adjustment of aligning at reversing"). Paper Original Fig.3-68 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 60...
  • Page 357: Automatic Adjustment Of Sensors And Initialization Of Eeprom

    Refer to P.2-43 "2.2.5 Adjustment mode (05) (e-STUDIO200L/230/280)" for the details. Errors such as paper jamming may occur if the EEPROM is not initialized and the sensors are not adjusted after the above mentioned parts were replaced.
  • Page 358: Adjustment Of Aligning

    Adjustment of aligning Adjust the aligning according to Step 1 of 3.10.3. - Rear side "-" of the original Rear side "+" of the original + Skew of paper Fig.3-69 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 62...
  • Page 359: Adjustment Of Aligning At Reversing

    3.10.6 Adjustment of aligning at reversing Adjust the aligning according to Step 3 of 3.10.3. Fig.3-70 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 63...
  • Page 360: Adjustment Of Reverse Solenoid

    (C) between A of the front frame and the flapper lever is 0.5 mm to 2.0 mm. Fig.3-73 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 64...
  • Page 361 (D) between the plunger and the flapper lever is eliminated. Flapper lever Fig.3-74 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 65...
  • Page 362: Adjustment Of Radf Opening/Closing Switch

    Adjustment of RADF opening/closing switch Adjust the bracket position so that the switch is turned ON when the height A becomes 40-45 mm (within the empty weight falling limit). Glass surface Center Fig.3-75 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 66...
  • Page 363: Adjustment Of Radf Opening/Closing Sensor

    Adjustment of RADF opening/closing sensor Adjust the bracket position so that the sensor is turned ON when the height A becomes 30-35 mm (within the empty weight falling limit). Glass surface Center Fig.3-76 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 67...
  • Page 364: Adjustment Of Tray Volume

    Narrow the original guide to the limit. Input the code "367". Press the [START] button. Fig.3-77 Extend the original guide to the limit. Input the code "368". Press the [START] button Turn the power OFF. Fig.3-78 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 68...
  • Page 365: Adjustment Of The Radf (Mr-3020)

    Open the RADF and install 2 positioning pins (the positioning pins are installed to the back side of the hinge which is on the left side of the RADF). Fig.3-79 Remove the platen sheet. Fig.3-80 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 69 05/11...
  • Page 366 If the pins cannot be fitted into the holes, perform the adjustment according to the following procedure. Remove the right-hand hinge screw at the rear side. Fig.3-82 Loosen the left-hand hinge screw at the rear side. Fig.3-83 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 70 05/11...
  • Page 367 Position the pins with the holes on the RADF by moving it so that the pins fit into the holes when the RADF is closed. Fig.3-85 Tighten the left-hand hinge screw at the rear side. Fig.3-86 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 71 05/11...
  • Page 368 Loosen the hole position adjustment screws on the right hand side. Fig.3-87 Match the screw hole positions. Fig.3-88 Install the right-hand hinge screw at the rear side. Fig.3-89 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 72 05/11...
  • Page 369 (10) Place the platen sheet on the original glass and align it to the top left corner. Close the RADF gently and open it to check if the platen sheet is attached properly. Fig.3-91 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 73 05/11...
  • Page 370: Adjustment Of Radf Height

    "B" from the left hand side of the equipment. If the value is not within the tolerance, perform the adjustment according to the following procedure. [Tolerance of the gap] Rear side: 0 - 0.5 mm Front side: 0 mm Fig.3-92 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 74 05/11...
  • Page 371 Adjust the gap on the rear side by means of the screw on the hinge on the feed side of the RADF. Turn it clockwis ....Lowered Turn it counterclockwise ..Heightened Fig.3-94 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 75 05/11...
  • Page 372: Adjustment Of Skew

    Place the chart provided as an original with its face up on the original tray of the RADF, select [2 Sided -> 2 Sided] and press the [START] button. Superimpose the chart on the copy and check the inclination of the copy image. e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 76 05/11...
  • Page 373 If the image skew is "C" as shown in the figure below, shift the aligning plate in the direction of "+", and if "D", shift it to "-". Fig.3-97 Fig.3-98 Shift the aligning plate in the direction of "+". Shift the aligning plate in the direction of "-". June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 77 05/11...
  • Page 374 If the image skew is "C" as shown in the figure below, shift the aligning plate in the direction of "- ", and if "D", shift it to "+". Fig.3-100 Fig.3-101 Shift the aligning plate in the direction of "-". Shift the aligning plate in the direction of "+". e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 78 05/11...
  • Page 375: Adjustment Of The Leading Edge Position

    If the leading edge (F) margin of the copy image is smaller than the (E) margin of the chart, enter a value larger than the current one. Note: Note: Changing one value shifts the copy image by 0.1 mm. Press the [ENTER] button. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 79 05/11...
  • Page 376: Adjustment Of Horizontal Position

    Changing one value shifts the copy image by 0.042 mm. Fig.3-104 • If the center line of the copy image is shifted to the rear side of the equipment, enter a value smaller than the current one. e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 80 05/11...
  • Page 377 Note: Note: Changing one value shifts the copy image by 0.042 mm. Fig.3-105 Press the [ENTER] button. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 81 05/11...
  • Page 378: Adjustment Of Copy Ratio

    • If the copy image dimension “I” is smaller than the chart dimension, enter a value larger than the current one. Fig.3-106 Press the [ENTER] button. e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 82 05/11...
  • Page 379: Adjustment Of Radf Opening/Closing Sensor

    Adjustment of RADF Opening/Closing Sensor Adjust the bracket position so that the sensor is turned ON when the height “A” becomes 100 mm or less (within the empty weight falling limit). Fig.3-107 Fig.3-108 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 83 05/11...
  • Page 380: Adjustment Of The Finisher (Mj-1022)

    The rear jogging plate moves to the Fig.3-110 home position. Rear jogging plate Front jogging plate home position home position Jogging width 317mm Fig.3-111 Measure the jogging width (standard at 317 mm). e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 84...
  • Page 381 If the width is 316 mm in step (4), the dif- ference from the standard is -1 mm; it requires relocation of the sensor in the direction of arrow B by 1 mm. Fig.3-113 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 85...
  • Page 382: Adjusting The Angle Of The Jogging Plate

    0 mm to 0.5 mm.) Screw Butted Rear jogging plate Finisher Fig.3-115 With reference to the rear jogging plate adjusted in step (2), adjust the front jogging plate in the same manner. e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 86...
  • Page 383: Adjusting The Overlap Of The Sensor Flag

    Tighten the screw so that the overlap between the flag of the front/rear jogging Sensor Sensor flag rack plate and the sensor is 1.5 mm to 2.0 1.5 mm to 2.0 mm Fig.3-117 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 87...
  • Page 384: Adjusting The Tension Of The Stack Processing Motor Belt

    Move the returning roller shaft to its lower Returning limit (the slack of a belt is lightly taken); then, roller shaft Screw tighten the screw on the tension arm plate. Tension arm plate Fig.3-120 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 88...
  • Page 385 Check to make sure that the returning roller Returning shaft moves smoothly. roller shaft Fig.3-121 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 89...
  • Page 386: Releasing The Stack Tray Guide Lever Fixing Plate

    (Perform the same for the front and the rear.) Fig.3-122 Note: Note: When removing the mounting screw, be sure to hold the stack tray guide lever up from below. Stack tray guide lever Fig.3-123 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 90...
  • Page 387: Adjustment Of The Upper Tray Angle

    While pushing the bracket down, hold the Bracket tray and move it up or down, to adjust the angle so that the tray becomes parallel by a visual check. Fig.3-126 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 91...
  • Page 388 After adjustment, tighten the fixing screw of the bracket. Note: Note: If the fixing screw of the bracket is not fixed, the belt is loosened which may cause a skipped tooth. Fig.3-127 e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 92...
  • Page 389: Dip Switch Functions

    The lower stack tray moves up and • Press SW2 again. motor (up) stops when the lower stack tray • Turn OFF the joint upper limit sensor is turned ON. sensor (S4). June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 93...
  • Page 390 The upper and lower stack trays • Turn OFF the joint operation move to the shipping position and sensor (S4). stop. Note: Note: Perform the shipping position operation when the finisher is packed again. e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 94...
  • Page 391: Adjustment Of The Finisher (Mj-1025)

    PCB to OFF. Enter the bind mode of the host machine and check whether the folding position is adjusted prop- erly. If adjusted improperly, adjust the folding position again. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 95...
  • Page 392: Adjusting The Sensor Output (Electrical System (Puncher Unit; Option))

    Press SW1002 or SW1003 on the punch controller PCB. A press will automatically adjust the sensor output. • The adjustment is over when all LEDs on the punch controller PCB are ON: LED 1001, LED1002, LED1003. Shift all bits of DIPSW1001 to OFF. e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 96...
  • Page 393: Registering The Number Of Punch Hole (Electrical System (Puncher Unit; Option))

    A single press on SW1003 will cause the LED indication to flash; another press on SW1003 will cause the indication to remain ON to indicate the end of registration. Shift all bits of DIPSW1001 to OFF. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 97...
  • Page 394: After Replacing The Eep-Rom (Ic1002 Electrical System (Puncher Unit; Option))

    Press SW1002 and SW1003 on the punch controller PCB at the same time. • The presses will initialize the EEP-ROM. At the end, all LEDs (LED1001, LED1002, LED1003) will go ON. Adjust the sensor output, and store the number of punch holes. e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 98...
  • Page 395: Key Copy Counter (Mu-8, Mu-10)

    (Treat the cut harness properly to avoid it causing a short circuit with the machine frame.) Then, disconnect the dummy connector. Harness connector Dummy connector Fig.3-135 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 99...
  • Page 396 Insert the key copy counter with its arrow mark pointing the rear side of the equipment. Key copy counter Fig.3-137 Enter the value “3” in the setting mode (08- 202). e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 100...
  • Page 397: Adjustment Of Dogleg

    Feeding Direction Fig.3-138 Dogleg Image A Dogleg Image B Feeding Feeding Direction Direction Approx. 48 mm of Approx. 48 mm of the trailing edge the trailing edge Fig.3-139 Fig.3-140 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 101 06/01...
  • Page 398 <Adjustment procedure> Check the position of the adjustment screws. Fig.3-141 Remove the 2 adjustment screws. e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 102 06/01...
  • Page 399 1 mm. Scale Be sure to make the scales on the right and left match when installing the adjustment screws. Fig.3-144 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ADJUSTMENT 3 - 103 06/01...
  • Page 400 ADJUSTMENT June 2004 © TOSHIBA TEC 3 - 104...
  • Page 401: Preventive Maintenance (Pm)

    * The screen goes back to the main screen when the counter clear is executed or the [CANCEL] button is pressed after moving from the main screen, while it goes back to the sub screen after moving from the sub screen. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) 4 - 1...
  • Page 402 The paper source differs depending on the structure of options, however, “0.0k” is displayed in “OUTPUT PAGES (k)” and its standard number of output pages is displayed in “PM OUT- PUT PAGES (k)” even for the installed paper source. e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) June 2004 © TOSHIBA TEC 4 - 2...
  • Page 403 Displaying of the standard number of drive counts (x 1,000) to replace the sub unit (parts) Displaying of the number of output pages counts, drive counts and previous replacement date for a chosen sub unit June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) 4 - 3...
  • Page 404 3) Clear screen Fig. 4-4 When the [INITIALIZE] button is pressed, “Present number of output pages counts” and “Present driving counts” are cleared and “Previous replacement date” is updated. e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) June 2004 © TOSHIBA TEC 4 - 4...
  • Page 405 Separation roller [SEP ROLLER (3rd CST.)] PFP lower drawer [4th CST.] Pickup roller [PICK UP ROLLER (4th CST.)] Feed roller [FEED ROLLER (4th CST.)] Separation roller [SEP ROLLER (4th CST.)] June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) 4 - 5...
  • Page 406: Work Flow Of Parts Replacement

    Check the drive counts of all parts at PM support mode. Does it exceed the specified drive count? Replace the part. Check the part and equipment according to the “TROUBLESHOOTING”. e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) June 2004 © TOSHIBA TEC 4 - 6...
  • Page 407: General Descriptions For Pm Procedure

    General Descriptions for PM Procedure Perform the preventive maintenance in the following timing. e-STUDIO200L/202L: every 6,400 sheets e-STUDIO230/232: every 74,000 sheets e-STUDIO280/282: every 90,000 sheets Preparation • Ask the user about the current conditions of the equipment and note them down.
  • Page 408: Operational Items In Overhauling

    Replace them with new ones if necessary. Check the performance of all the switches and sensors. Replace them with new ones if neces- sary. Clean inside the equipment thoroughly. e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) June 2004 © TOSHIBA TEC 4 - 8 05/11...
  • Page 409: Preventive Maintenance Checklist

    Silicon oil Inspector’s ' Replace if White grease name deformed or (Molykote X5-6020) damaged Remarks White grease (Molykote HP-300) Alvania No.2 Floil (GE-334C) Conductive grease (KS-660) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) 4 - 9...
  • Page 410 74,000 sheets e-STUDIO280/282: every 90,000 sheets • Values under “Replacement” indicate the replacement cycle for the e-STUDIO200L/ e-STUDIO230/e-STUDIO280 or e-STUDIO202L/e-STUDIO232/e-STUDIO282. • The replacement cycle of the parts in the feeding section equals to the number of sheets fed from each paper source.
  • Page 411 (x 1,000 sheets) check <P-I> Pickup roller 80/80 <P20-I4> Feed roller 80/80 <P20-I4> Separation roller AV, W2 80/80 <P19-I4> Bypass tray Drive gear (tooth face and shaft) GCB bushing bearing June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) 4 - 11...
  • Page 412 Photoconductive drum 64/74/90 Chap. 4.8.2 Discharge LED Whole cleaner unit Drum cleaning blade 64/74/90 <P27-I5> Separation finger for 64/74/90 drum Recovery blade 64/74/90 <P27-I6> Ozone filter 128/148/180 <P12-I8> e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) June 2004 © TOSHIBA TEC 4 - 12...
  • Page 413 <P30-I24> K. Exit unit Replacement Operation Parts list Items to check Cleaning Lubrication Remarks (x 1,000 sheets) check <P-I> Exit/reverse guide <P31-I21> Exit roller <P31-I3> Drive gear June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) 4 - 13 04/09...
  • Page 414 N. LCF (KD-1012) Replacement Operation Parts list Items to check Cleaning Lubrication Remarks (x 1,000 sheets) check <P-I> Pickup roller <P4-I30> Feed roller <P4-I28> Separation roller <P5-I12> Drive gear e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) June 2004 © TOSHIBA TEC 4 - 14 04/09...
  • Page 415 { or A Paper fold roller { or A Bind delivery roller { or A Waste full detection sensor Feeding assembly { or A member Paper guide { or A June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) 4 - 15...
  • Page 416 Separation roller 4-10 Feed roller Registration roller Intermediate transfer roller Front read roller Platen roller Rear read roller Reverse registration roller Exit/reverse roller Platen sheet { or A e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) June 2004 © TOSHIBA TEC 4 - 16 05/11...
  • Page 417 F2 F4 E3 E2 Fig. 4-6 Front side June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) 4 - 17...
  • Page 418 L10 L11 L12 Fig. 4-7 Reversing Automatic Document Feeder (RADF: MR-3016) Fig. 4-8 Paper Feed Pedestal (PFP) Fig. 4-9 Large Capacity Feeder (LCF) e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) June 2004 © TOSHIBA TEC 4 - 18 05/11...
  • Page 419 Fig. 4-10 Job Separator (JSP) Fig. 4-11 Offset Tray (OCT) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) 4 - 19...
  • Page 420 Fig. 4-12 Finisher (MJ-1025) Fig. 4-13 Reversing Automatic Document Feeder (RADF: MR-3020) e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) June 2004 © TOSHIBA TEC 4 - 20 05/11...
  • Page 421 Molykote to the gear which is located near the clutch. The quantity of Molykote should be smaller than that to be applied to the other parts. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) 4 - 21...
  • Page 422 Be careful of the following when attaching a new wire (length: 353 mm) Insert the wire securely into the V-grooves of the front and rear sides. Do not twist the wire. Do not touch the wire with your bare hand. e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) June 2004 © TOSHIBA TEC 4 - 22...
  • Page 423 Apply an even coat of grease to the inside of Outside the oil seal. • Amount: About two small drops Wipe off any grease the exudes from the Inside Grease inside. Oil seal Fig. 4-18 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) 4 - 23...
  • Page 424 OCT separator roller Apply one-rice-grain-amount of FLOIL (GE-334C) to the part A in the figure below. Also apply three-rice-grain-amount of white grease (Molykote X5-6020) to each part B. Fig. 4-20 e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) June 2004 © TOSHIBA TEC 4 - 24...
  • Page 425 Pickup roller ROLLER-PICK-AT Feed roller K-ROLL-FEED Separation roller K-ROLL-SPT ROL-KIT-1010 Pickup roller ROLL-PICK-UP Feed roller ROLL-PAPER-FED-F Separation roller ROLL-PAPER-FED-S DF-KIT-3015 Pickup roller ROLL-PICK-UP Feed roller ROLL-FEED Separation roller ROL-SPT-513 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) 4 - 25...
  • Page 426: Jig List

    Belt tension jig High-voltage transformer jig Downloading jig (DLM board) Download JIG-2 (6 Flash ROMs) Download JIG-1 (2 Flash ROMs) ROM writer adapter (For 1881) ROM writer adapter (For 1931) e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) June 2004 © TOSHIBA TEC 4 - 26...
  • Page 427: Grease List

    White grease (Molykote HP-300) ASM-PG-HP300-S 100g Bottle White grease (Molykote HP-300) GREASE-HP300-S Bottle Alvania No.2 ASM-PG-ALV2 100g Tube White grease (Molykote X5-6020) MOLYKOTE-100 100g Tube Floil (GE-334C) ASM-PG-GE334C-S Bottle June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) 4 - 27...
  • Page 428: Precautions For Storing And Handling Supplies

    Precautions for Storing and Handling Supplies 4.8.1 Precautions for storing TOSHIBA supplies 1) Toner/Developer Toner and developer should be stored in a place where the ambient temperature is between 10°C to 35°C (no condensation), and should also be protected against direct sunlight during transportation.
  • Page 429: Checking And Cleaning Of Photoconductive Drum

    6) Collecting used photoconductive drums Regarding the recovery and disposal of used photoconductive drums, we recommend following the relevant local regulations or rules. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) 4 - 29...
  • Page 430: Checking And Cleaning Of Drum Cleaning Blade

    When its surface is stained with toner, check the cleaning roller. If toner is heavily adhered on the cleaning roller, the cleaning roller should be replaced with new ones. Replace it when a specified number of output pages have been made. e-STUDIO200L/202L/230/232/280/282 PREVENTIVE MAINTENANCE (PM) June 2004 © TOSHIBA TEC 4 - 30...
  • Page 431: Troubleshooting

    4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the registration roller clutch. 6) Replace the LGC board. È Check the registration roller. Replace it if it is worn out. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 1...
  • Page 432 PFP lower drawer feed sensor 03-[FAX]OFF/[4]/[D] Bridge unit Bridge unit Bridge unit transport sensor-1 03-[FAX]ON/[3]/[H] Bridge unit transport sensor-2 03-[FAX]ON/[3]/[E] JSP cover JSP feed sensor 03-[FAX]ON/[3]/[H] OCT cover OCT feed sensor 03-[FAX]ON/[3]/[H] e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 2...
  • Page 433 1) Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2) Check the transport roller. Replace it if it is worn out. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 3...
  • Page 434 1) Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2) Check the transport roller. Replace it if it is worn out. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 4...
  • Page 435 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the registration roller clutch. 6) Replace the LGC board. È Check the registration roller. Replace it if it is worn out. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 5...
  • Page 436 1) Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2) Check the transport roller. Replace it if it is worn out. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 6...
  • Page 437 1) Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2) Check the PFP transport roller. Replace it if it is worn out. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 7...
  • Page 438 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the ADU clutch. 6) Replace the LGC board. È Check the rollers in the ADU. Replace them if they are worn out. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 8...
  • Page 439 7) Replace the ADU board. 8) Replace the LGC board. È Check the rollers in the ADU and the exit roller of the equipment. Replace them if they are worn out. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 9...
  • Page 440 Bridge unit Bridge unit transport sensor-1 03-[FAX]ON/[3]/[H] Bridge unit transport sensor-2 03-[FAX]ON/[3]/[E] JSP cover JSP feed sensor 03-[FAX]ON/[3]/[H] OCT cover OCT feed sensor 03-[FAX]ON/[3]/[H] Finisher Finisher door Sensors in the finisher e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 10...
  • Page 441 6) Replace the OCT feed sensor. 7) Replace the OCT board. 8) Replace the LGC board. È 1) Replace the OCT board. 2) Replace the LGC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 11...
  • Page 442 5) Check if the conductor patterns on the ADU board and LGC board are short circuited or open circuited. 6) Replace the ADU exit sensor. 7) Replace the ADU board. 8) Replace the LGC board. È e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 12...
  • Page 443 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the 1st/2nd transport sensor. 6) Replace the LGC board. È Check the rollers. Replace them if they are worn out. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 13...
  • Page 444 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the registration sensor. 6) Replace the LGC board. È Check the rollers. Replace them if they are worn out. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 14...
  • Page 445: Paper Misfeeding

    4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the ADU clutch. 6) Replace the LGC board. È Check the rollers in the ADU. Replace them if they are worn out. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 15...
  • Page 446 5) Replace the bypass feed clutch and bypass paper sensor. 6) Replace the LGC board. È Check the bypass transport, feed separation and pickup rollers. Replace them if they are worn out. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 16...
  • Page 447 5) Replace the upper drawer feed clutch. 6) Replace the LGC board. È Check the upper drawer feed roller, separation roller and pickup roller. Replace them if they are worn out. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 17...
  • Page 448 5) Replace the lower drawer feed clutch. 6) Replace the LGC board. È Check the lower drawer feed roller, separation roller and pickup roller. Replace them if they are worn out. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 18...
  • Page 449 7) Replace the PFP board. 8) Replace the LGC board. È Check the PFP upper drawer feed roller, separation roller and pickup roller. Replace them if they are worn out. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 19...
  • Page 450 7) Replace the PFP board. 8) Replace the LGC board. È Check the PFP lower drawer feed roller, separation roller and pickup roller. Replace them if they are worn out. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 20...
  • Page 451 6) Replace the LCF feed clutch. 7) Replace the LCF board. 8) Replace the LGC board. È Check the LCF feed roller, separation roller and pickup roller. Replace them if they are worn out. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 21...
  • Page 452: Cover Open Jam

    3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the LGC board. È Replace the LGC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 22...
  • Page 453 3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the LGC board. È Replace the LGC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 23...
  • Page 454 6) Replace the PFP side cover opening/closing switch. 7) Replace the PFP board. 8) Replace the LGC board. È 1) Replace the PFP board. 2) Replace the LGC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 24...
  • Page 455 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the side door switch. 6) Replace the LGC board. È Replace the LGC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 25...
  • Page 456 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the bridge unit opening/closing switch. 6) Replace the LGC board. È Replace the LGC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 26...
  • Page 457 6) Replace the OCT cover switch. 7) Replace the OCT board. 8) Replace the LGC board. È 1) Replace the OCT board. 2) Replace the LGC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 27...
  • Page 458: Transport Jam (Radf)

    4) Check if the conductor pattern on the RADF board is short circuited or open circuited. 5) Replace the original length sensor and registration sensor. 6) Replace the RADF board. È Replace the RADF board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 28...
  • Page 459 4) Check if the conductor pattern on the RADF board is short circuited or open circuited. 5) Replace the read sensor. 6) Replace the RADF board. È Replace the RADF board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 29...
  • Page 460 4) Check if the conductor pattern on the RADF board is short circuited or open circuited. 5) Replace the registration sensor. 6) Replace the RADF board. È Replace the RADF board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 30...
  • Page 461 Check if the conductor pattern on the RADF board is short circuited or open circuited. Replace the RADF board. Check if the conductor pattern on the SLG board is short circuited or open circuited. Replace the SLG board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 31 05/05...
  • Page 462 4) Check if the conductor pattern on the RADF board is short circuited or open circuited. 5) Replace the reverse sensor. 6) Replace the RADF board. È Replace the RADF board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 32...
  • Page 463 4) Check if the conductor pattern on the RADF board is short circuited or open circuited. 5) Replace the exit sensor. 6) Replace the RADF board. È Replace the RADF board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 33...
  • Page 464 4) Check if the conductor pattern on the RADF board is short circuited or open circuited. 5) Replace the RADF opening/closing sensor. 6) Replace the RADF board. È Replace the RADF board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 34...
  • Page 465: Finisher Jam

    (Perform the output check: 03-101/151) NO Æ Check the drive system of the equipment and bridge unit. È Check the roller in the bridge unit. Replace it if it is worn out. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 35...
  • Page 466 Is the punch home position sensor working properly? NO Æ 1) Connect the connector of the punch home position sensor securely. 2) Replace the punch home position sensor. È Replace the punch controller PC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 36...
  • Page 467 Is the inlet sensor working normally? (Check the movement of the actuator.) NO Æ 1) Attach the actuator securely if its shaft is out of place. È 2) Replace the sensor. Replace the finisher controller PC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 37...
  • Page 468 Is the inlet sensor working normally? (Check the movement of the actuator.) NO Æ 1) Attach the actuator securely if its shaft is out of place. 2) Replace the sensor. È Replace the finisher controller PC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 38...
  • Page 469 NO Æ 1) Attach the actuator securely if its shaft is out of place. 2) Replace the sensor. È Replace the finisher controller PC board. Replace the punch controller PC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 39...
  • Page 470 Are the joint switch, upper cover sensor and front door sensor working properly? NO Æ 1) Attach the actuator securely if its shaft is out of place. È 2) Replace the switch or sensor. Replace the finisher controller PC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 40...
  • Page 471 Are the slide home position sensor and stapler safety switch working properly? NO Æ 1) Replace the stapler unit. È 2) Replace the stapler safety switch. Replace the finisher controller PC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 41...
  • Page 472 1) Connect the connector of the inlet sensor securely. 2) Attach the actuator securely if its shaft is out of place. È 3) Replace the inlet sensor. Replace the finisher controller PC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 42...
  • Page 473 Rotate the delivery motor by hand. Is there any mechanical problem with the rotation of the stack delivery belt? Are the latches of the stack delivery belt damaged? YES Æ Fix the mechanism. È Replace the finisher controller PC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 43...
  • Page 474 Is the returning roller home position sensor working properly? NO Æ 1) Connect the connector of the returning roller home position sensor securely. È 2) Replace the returning roller home position sensor. Replace the finisher controller PC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 44...
  • Page 475 YES Æ Connect the connector securely. Replace the harness. È Is the folding position sensor working properly? NO Æ Replace the sensor. È Replace the finisher controller PC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 45...
  • Page 476 NO Æ Connect the pin or replace the harness. È 1) Replace the IPC board. 2) Replace the LGC board. 3) Replace the finisher controller PC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 46...
  • Page 477: Drive System Related Service Call

    1) Check if the PLL lock signal CN305-B8 output from the LGC board is always level “L”? 2) Check if the voltage supplied to the CPU input terminal IC24-12 is always “L”? 3) Replace the LGC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 47...
  • Page 478: Paper Feeding System Related Service Call

    1) Check if the PLL lock signal CN246-8 output from the PFP board is always “L” level. 2) Check if the voltage supplied to the microcomputer input terminal IC5-17 is always “L” level. 3) Replace the PFP board. 4) Replace the LGC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 48...
  • Page 479 5) Check if the conductor pattern on the LGC board is short circuited or open circuited. 6) Replace the LGC board. È 1) Check if the conductor pattern on the LGC board is short circuited or open circuited. 2) Replace the LGC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 49...
  • Page 480 7) Replace the PFP board. 8) Replace the LGC board. È 1) Check if the conductor pattern on the LGC board is short circuited or open circuited. 2) Replace the LGC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 50...
  • Page 481 7) Replace the LCF board. 8) Replace the LGC board. È 1) Check if the conductor pattern on the LGC board is short circuited or open circuited. 2) Replace the LGC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 51...
  • Page 482 7) Replace the LCF board. 8) Replace the LGC board. È 1) Check if the conductor pattern on the LGC board is short circuited or open circuited. 2) Replace the LGC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 52...
  • Page 483 4) Check if the voltage supplied to the microcomputer input terminal IC103-17 is always “L” level. 5) Replace the LCF transport motor. 6) Replace the LCF board. 7) Replace the LGC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 53...
  • Page 484: Scanning System Related Service Call

    3) Check if the conductor pattern on the SLG board is short circuited or open circuited. 4) Replace the SLG board. 5) Replace the inverter. 6) Replace the exposure lamp. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 54...
  • Page 485 1) Check if the connector pins are disconnected and the harnesses are short circuited or open circuited. 2) Check if the conductor pattern on the SLG board is short circuited or open circuited. 3) Replace the SLG board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 55...
  • Page 486: Fuser Unit Related Service Call

    Change the current status counter value “1” or “2” to “0”, then press [ENTER] or [INTERRUPT] (to cancel [C410]). Turn the power OFF and then back ON. Make sure that the equipment enters the normal ready state. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 56...
  • Page 487 Check if the conductor pattern on the board is short circuited or open circuited. Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) “6” to “0”. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 57...
  • Page 488: Communication Related Service Call

    Check the version of the system ROM on the SYS board. Check the version of the scanner ROM version on the SLG board. Replace the SYS board. Replace the SLG board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 58 05/05...
  • Page 489: Radf Related Service Call (Mr-3016)

    Check the circuits and connectors on the RADF board, mainly IC3, IC4 and CN3, for short cir- cuits and open circuits. Replace the original length sensor. Replace the RADF board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 59 05/11...
  • Page 490: Radf Related Service Call (Mr-3020)

    (CN313) and LRL board (CN204), and between the LRL board (CN204) and laser optical unit? YES Æ Replace the harness. Connect the disconnected connectors. È 1) Replace the LGC board. 2) Replace the laser optical unit. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 60 05/11...
  • Page 491: Finisher Related Service Call

    Try turning the stack feed roller (upper) shaft by hand. Does the stack feed roller (upper) move up/down normally? NO Æ Fix the mechanism. È Try replacing the feed motor (M1). Is the problem corrected? YES Æ End. È Replace the finisher controller PC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 61...
  • Page 492 Rotate the stack delivery roller by hand. Does it rotate smoothly? NO Æ Fix the mechanism. È Try replacing the delivery motor (M3). Is the problem corrected? YES Æ END. È Replace the finisher controller PC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 62...
  • Page 493 È Is the wiring between the finisher controller PC board and shift upper limit sensor (PI15) cor- rect? YES Æ Replace the finisher controller PC board. È Correct the wiring. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 63...
  • Page 494 Try to rotate the staple jam releasing dial. Is there mechanical trapping? YES Æ Fix the mechanism. È Try replacing the staple/fold motor (M7). Is the problem corrected? YES Æ End. È Replace the finisher controller PC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 64...
  • Page 495 Try to rotate the fold jam releasing dial. Is there mechanical trapping? YES Æ Fix the mechanism. È Try replacing the staple/fold motor (M7). Is the problem corrected? YES Æ End. È Replace the finisher controller PC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 65...
  • Page 496 Is there any mechanical problem with the stapler stand motion path? YES Æ Fix the mechanism. È Try replacing the slide motor (M8). Is the problem corrected? YES Æ End. È Replace the finisher controller PC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 66...
  • Page 497 Is the stack delivery lever home position sensor (S8) working properly? NO Æ Replace the sensor. È 1) Replacing the stack processing motor. 2) Replace the finisher controller PC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 67...
  • Page 498 YES Æ Fix the mechanism. È Try replacing the paddle motor. Is the problem corrected? YES Æ End. È Replace the finisher controller PC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 68...
  • Page 499 YES Æ Fix the mechanism. È Replace Punch motor (M1P) Try replacing the punch controller PC board. Is the problem corrected? YES Æ End. È Replace the finisher controller PC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 69...
  • Page 500 Is there any mechanical problem with the path of aligning plate? YES Æ Fix the mechanism. È Try replacing the alignment motor (front) (M4). Is the problem corrected? YES Æ End. È Replace the finisher controller PC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 70...
  • Page 501 Replace the finisher controller PC board. È Check the wiring between the upper stack tray lift motor and finisher controller PC board. If there is no problem, replace the upper stack tray lift motor. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 71...
  • Page 502 Replace the finisher controller PC board. È Check the wiring between the upper stack tray lift motor and finisher controller PC board. If there is no problem, replace the motor. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 72...
  • Page 503 Is there any mechanical problem with the path of aligning plate? YES Æ Fix the mechanism. È Try replacing the alignment motor (rear) (M5). Is the problem corrected? YES Æ End. È Replace the finisher controller PC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 73...
  • Page 504 Is there any mechanical problem with the fold jam releasing dial? YES Æ Fix the mechanism. È 1) Replace the staple/fold motor (M7). 2) Replace the finisher controller PC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 74...
  • Page 505 Measure the voltage between CN14-5 (+) and CN14-3 (-) on the finisher controller PC board 24 V? NO Æ Replace the finisher controller PC board. È Replace the punch controller PC board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 75...
  • Page 506: Service Call For Others

    When the message “SRAM ERROR DOES IT INITIALIZE?” is displayed on the LCD, press [INI- TIALIZE]. (SRAM is cleared.) Turn the power OFF and then back ON. If the error is not recovered, replace the SYS board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 76...
  • Page 507 Perform the bad sector check (08-694). If the check result is OK, recover the data in the HDD. If the check result is failed, replace the HDD. Replace the SYS board. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 77...
  • Page 508 [F200] Data overwrite kit (GP-1050/1060) is taken off Clear the service call “F200”. (Key in “0” at 08-633.) * When the Data overwrite kit (GP-1050/1060) is taken off from the equipment, the service call “F200” occurs. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 78 05/11...
  • Page 509: Error In Internet Fax / Scanning Function

    Note that some of data cannot be backed up (Page 5-1). [ 1 ] Internet FAX related error (when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280)) (when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282)) [1C10] System access abnormality [1C32] File deletion failure Turn the power OFF and then back ON.
  • Page 510 [1C68] NIC access error [1C6D] System error Turn the power OFF and then back ON. Perform the job in error again. If the error still occurs, replace the NIC board. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 80...
  • Page 511 [1C82] Internet FAX transmission failure when processing FAX job received Reset the “Received Fax Forward”. [1CC1] Power failure Check if the power cable is connected properly and it is inserted securely. Check if the power voltage is unstable. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 81 05/11...
  • Page 512 [ 2 ] RFC related error (when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280)) (when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282)) [2500] HOST NAME error (RFC: 500) / Destination mail address error (RFC: 500) / Terminal mail...
  • Page 513 If it can be printed out, perform the job in error again. If it can not be printed out, replace the main memory. If the recovery is still not completed, perform the HDD formatting (08-690). June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 83...
  • Page 514 Backup the documents in the box or folder to PC or delete them. [2BF2] Exceeding maximum number of folders Backup the folders in the box or folder to PC or delete them. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 84...
  • Page 515 [ 4 ] E-mail related error (when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280)) (when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282)) [2C10] System access abnormality [2C32] File deletion failure Turn the power OFF and then back ON. Perform the job in error again.
  • Page 516 [2C6B] Terminal mail address error Check if there is an illegal character in the Terminal mail address. Delete the illegal character and reset the appropriate Terminal mail address, then perform the job again. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 86...
  • Page 517 Reset the setting of the mail box or “Received InternetFax Forward”. [2CC1] Power failure Check if the power cable is connected properly and it is inserted securely. Check if the power voltage is unstable. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 87 05/11...
  • Page 518 [ 5 ] File sharing related error (when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280)) (when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282)) [2D10] System access abnormality [2D32] File deletion failure [2DA6] File deletion failure [2DA7] Resource acquiring failure...
  • Page 519 Check if the setting of SMB is valid. [2DC1] Power failure Check if the power cable is connected properly and it is inserted securely. Check if the power voltage is unstable. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 89...
  • Page 520 [ 6 ] E-mail reception related error (when GM-1020/3020, 1030/3030, 2020 or 2030 is installed (e-STUDIO200L/230/280)) (when GM-1070/4070, 1080U/4080U, 2070 or 2080U is installed (e-STUDIO202L/232/282)) [3A10] [3A11] [3A12] E-mail MIME error The format of the mail is not corresponding to MIME 1.0.
  • Page 521 Inform the sender that the transfer of the FAX data over 40 is not supported. [3D30] FAX board error This error occurs when the FAX board is not installed or the FAX board has an abnormality. Check if the FAX board is correctly connected. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 91...
  • Page 522 When there are running jobs, perform the job in error again after the completion of the running jobs. If the error still occurs, turn the power OFF and then back ON, and perform the job again. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 92 05/11...
  • Page 523 [A290] Limit over error [A291] Limit over error [A292] Limit over error Clear the limit counter. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 93 05/11...
  • Page 524: Troubleshooting For The Image

    Is background fogging occurring? Perform troubleshooting for back- ground fogging. Is there a blotch on the image? Perform troubleshooting for blotched image. Is the image transferred normally? Perform troubleshooting for abnor- mal transfer. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 94...
  • Page 525 Is the drum cleaned properly? Check the pressure of the drum cleaning blade. Toner dusting Is toner heaped on the seal of the Remove the toner and clean the developer unit? developer unit. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 95...
  • Page 526 Check the image processing param- Check the encircled areas A and B in eters. the image, and change the sharp- ness intensity in the sharpness adjustment mode. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 96...
  • Page 527 Using the specified developer mate- Use the specified developer material rial? and toner. Scanner Are the original glass (especially the Clean them. position of shading correction plate), mirror and lens dirty? June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 97...
  • Page 528 Ozone exhaust Is the exhaust fan operating prop- Check the connection of connector. erly? Replace the ozone exhaust fan. Is the ozone filter stained or dam- Replace the ozone filter. aged? e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 98...
  • Page 529 Check the setting and correct it. roller in each paper type normal? 08-412, 413, 437, 438, 451, 452, 453, 518, 520, 521 Using the recommended paper? Use the recommended paper. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 99...
  • Page 530 CCD, SLG, SYS, LGC Are the connectors securely con- Connect the connectors securely. boards and harnesses nected? Replace the harness. Check if the harnesses connecting the boards are open circuited. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 100...
  • Page 531 CCD, SLG, SYS, LGC Are the connectors securely con- Connect the connectors securely. boards and harnesses nected? Replace the harness. Check if the harnesses connecting the boards are open circuited. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 101...
  • Page 532 Are the original glass (especially the Clean them. position of shading correction plate) mirror and lens dirty? Cleaner Is there any foreign matter, which Remove the foreign matter. contacts the drum on the cleaner stay? e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 102...
  • Page 533 Is any foreign matter such as paper Remove the foreign matter from the shred sticking to the transfer charger wire. wire? Feed system Is the aligning amount proper? Adjust the aligning amount. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 103...
  • Page 534 Attach the spring correctly. Clean the tration roller? roller if it is dirty. Pre-registration guide Is the pre-registration guide properly Correct it. installed? Carriage-1 Is the carriage-1 slanted? Adjust the carriage-1. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 104...
  • Page 535 Are there scratches on the drum sur- Replace the drum. face? Laser optical unit Is there a foreign matter or stain on Remove the foreign matter or the the slit glass? stain. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 105...
  • Page 536 Check and adjust the contact condi- the drum surface? tion of the cleaning blade and recov- ery blade. Scanner Is there a foreign matter on the car- Remove the foreign matter. riage rail? e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 106...
  • Page 537 / Transfer charger) Transfer/Separation Is there any foreign matter such as Clean the transfer/separation charger fiber in the paper transport area of charger. the transfer/separation charger? June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 107...
  • Page 538 Replace the clutch if it is defective. Adjust the rotation speed of the roller. High-voltage transformer Is the high-voltage transformer out- Adjust the output, or replace the (Transfer charger) put defective? transformer. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 108...
  • Page 539 Is the platen cover or RADF opened? Close the platen cover or RADF. Are the original glass (especially the Clean them. position of shading correction plate), mirror and lens dirty? June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 109...
  • Page 540 Reconnect the harness securely. age harness securely connected? Is Replace the high-voltage harness. the harness open circuited? Discharge LED Are the connectors of discharge LED Reconnect the harness securely. harness securely connected? e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 110...
  • Page 541 Feed clutch Is the feed clutch working properly? Check the circuit or feed clutch, and replace them if necessary. Pre-registration guide Is the pre-registration guide installed Install the guide properly. properly? June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 111...
  • Page 542 Drum drive system Is there any problem with the drive Check the drive system of the drum. system of the drum? Clean or replace the gears if they have stains or scratches. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 112...
  • Page 543 Is the pressure of the fuser roller nor- Check and adjust the mechanism. mal? Is the setting temperature of the fuser Check the setting and correct it. roller normal? 08-407, 410, 411, 450, 515, 516 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 113...
  • Page 544 Exposure lamp Is the exposure lamp tilted? Adjust the position of the exposure lamp. Is the exposure lamp discolored or Replace the exposure lamp. degraded? e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 114...
  • Page 545 Is the transfer charger wire dirty? Clean the transfer charger wire. High-voltage transformer Is the output from the high-voltage Adjust the output. Replace the trans- (Transfer charger) transformer normal? former if necessary. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 115...
  • Page 546: Replacement Of Pc Boards And Hdd

    FAX saved data (Confidential / Bulletin board data) Print them. (The data cannot be backed up.) Registration data for FAX transmission (Delayed transmission / Recovery transmission) The data cannot be backed up. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 116 04/09...
  • Page 547 Restore them in the “Administrator” menu of TopAccess Department management data Import them in the “Administrator” menu of TopAccess. Image data in the Electronic Filing Upload them in the “e-Filing” of TopAccess. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 117 05/05...
  • Page 548 Press the [ADMIN] button, enter the password, and then press the [ENTER] button. Press the [FAX] button and then the [TERMINAL ID] button to set each item. Press the [INITIAL SETUP] button to set each item. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 118...
  • Page 549: Replacing Sys Board

    Install NVRAM to the new SYS board (from the old SYS board). Install NIC board to the new SYS board (from the old SYS board). (e-STUDIO200L/230/280) Update the version of system ROMs (System Firmware, OS data, UI data) (The ROMs had been used for the old SYS board).
  • Page 550 Images of fax transmission Images of fax reception (14) Turn the power OFF. (15) Turn the power ON. (16) Set the dial type. [USER FUNCTIONS] o [ADMIN] o [FAX] o [INITIAL SETUP] e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 120...
  • Page 551: Caution When Data Overwrite Kit (Gp-1050/1060) Is Installed

    HDD manufacturer Model name HDD serial number Items supported differ depending on the HDD manufacturer. "---" is displayed on the VALUE, NAV and Worst columns if items are not supported. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 121 05/11...
  • Page 552 The number of sectors reassigned This value tends to increase at HDD failure. Current Pending Sector Count The number of candidate sectors to This value tends to increase at be reassigned HDD failure. e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 122 05/11...
  • Page 553 This attribute is a measure of the total number of errors found in data transfer in the Ultra-DMA mode. Write Error Rate This attribute is a measure of the write error rate. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 123 05/11...
  • Page 554 TROUBLESHOOTING June 2004 © TOSHIBA TEC 5 - 124...
  • Page 555: Firmware Updating

    Updating with the download jig P.6-2 "6.1 Firmware Updating with Download Jig (e-STUDIO200L/230/280)" • Updating with PC connected P.6-54 "6.3 Firmware Updating with FSMS (Field Service Manager) (e-STUDIO200L/230/280)" • Updating with the USB Storage Device P.6-66 "6.4 Firmware Updating with USB Storage Device (e-STUDIO200L/230/280)"...
  • Page 556: Firmware Updating With Download Jig (E-Studio200L/230/280)

    K-PWA-DLM-320 — Refer to the following for the details to update with each download jig. P.6-4 "6.1.1 PWA-DWNLD-350-JIG2 (48 MB)" P.6-11 "6.1.2 PWA-DWNLD-350-JIG1 (16 MB)" P.6-21 "6.1.4 K-PWA-DLM-320" e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 2 05/11...
  • Page 557 P.6-20 "6.1.3 Writing the data to the download jig (PWA-DWNLD-350-JIG)" Connector Mark for ROM installation direction Fig.6-3 Jig board: K-PWA-DLM-320 Important: Pay attention to the direction of the ROM. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 3...
  • Page 558: Pwa-Dwnld-350-Jig2 (48 Mb)

    Write the data to the download jig. P.6-20 "6.1.3 Writing the data to the download jig (PWA-DWNLD-350-JIG)" Turn OFF the power of the equipment. Remove the cover plate. Cover plate Fig.6-4 e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 4...
  • Page 559 Connect the download jig with the jig connector (CN100) on the SYS board. Connector Fig.6-5 Turn ON the power. Downloading starts automatically and the processing status is displayed on LCD screen. Fig.6-6 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 5...
  • Page 560 Do the download jig and the equipment operate properly? Fig.6-8 Turn OFF the power, and then remove the download jig. Perform the “Updating System ROM” continuously. P.6-11 "6.1.2 PWA-DWNLD-350-JIG1 (16 MB)" <Updating System ROM> e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 6...
  • Page 561 08-937: Version of Web UI data language 4 in HDD 08-938: Version of Web UI data language 5 in HDD 08-939: Version of Web UI data language 6 in HDD June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 7...
  • Page 562 The processing status is displayed as follows on the LCD screen during the update. The device check starts. When the device check completes, copying the data to HDD starts. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 8...
  • Page 563 When copying all the files completes, the backup of the RIP font starts. When the backup of the RIP font completes, the update completes with the following screen. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 9...
  • Page 564 * If an error occurs, the following error message is displayed and the update is interrupted. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 10...
  • Page 565: Pwa-Dwnld-350-Jig1 (16 Mb)

    Write the ROM data to be updated to the download jig. P.6-20 "6.1.3 Writing the data to the download jig (PWA-DWNLD-350-JIG)" Turn OFF the power of the equipment. Remove the cover plate. Cover plate Fig.6-9 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 11...
  • Page 566 The screen for selecting the items to be updated is displayed. “*” is displayed next to the items to be updated. (All items are selected in the default settings.) Fig.6-11 e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 12...
  • Page 567 (Updating the system ROM is taken as an example and explained.) Fig.6-12 Press the [START] button. Updating starts and the processing status is displayed on the LCD screen. Fig.6-13 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 13...
  • Page 568 • Is the download jig connected properly? • Is the updating data written to the download jig properly? • Do the download jig and the equipment operate properly? Fig.6-15 e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 14...
  • Page 569 OFF the power, and then restart updating from the beginning. If you turn OFF the power within 5 minutes, HDD may be destroyed. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 15...
  • Page 570 08-930: Version of UI data in FROM displayed at power ON <Updating Engine ROM> 08-903: Engine ROM version <Updating Scanner ROM> 08-905: Scanner ROM version <Updating NIC ROM> 08-916: NIC ROM version e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 16...
  • Page 571 Press [START] button after selecting the item to be updated. The device check starts. When the device check completes, erasing the data in the ROM of the equipment starts. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 17...
  • Page 572 ROM of the equipment starts. When copying the data completes, verifying the data starts. When verifying the data completes, copying and verifying the other data are implemented repeatedly. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 18...
  • Page 573 When copying and verifying all the data com- plete, the update completes with the following screen. * If an error occurs, the following error message is displayed and the update is interrupted. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 19...
  • Page 574: Writing The Data To The Download Jig (Pwa-Dwnld-350-Jig)

    Minato Electronics MODEL 1893/1895/1931/1940 PWA-DL-ADP-350-1931 (or equivalent) (model 1931) model 1881 model 1881 model 1931 model 1931 ( LV 6 50 ) ( LV 6 5 0 ) Fig.6-19 PWA-DL-ADP-350-1931 Fig.6-18 PWA-DL-ADP-350-1881 e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 20...
  • Page 575: K-Pwa-Dlm-320

    <Updating Engine ROM> Engine ROM data <Updating Scanner ROM> Scanner ROM data <Updating RADF ROM> RADF ROM data <Updating Finisher ROM> Finisher ROM data <Updating FAX ROM> FAX ROM data June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 21 04/07...
  • Page 576 Make sure the direction is correct (P.6-3 "Fig.6-3"). Turn OFF the power of the equipment. Take off the connector cover. Connector cover Fig.6-20 Remove the cover plate. Cover plate Fig.6-21 e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 22...
  • Page 577 Is the updating data written on the ROM of the download jig properly? • Do the download jig and the equipment operate properly? Turn OFF the power, remove the download jig and install the cover plate and the connector cover. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 23...
  • Page 578 Make sure the direction is correct (P.6-3 "Fig.6-3"). Turn OFF the power of the equipment. Take off the right upper cover-1. Right upper cover-1 Fig.6-23 Take off the right upper cover-2. Right upper cover-2 Fig.6-24 e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 24...
  • Page 579 Do the download jig and the equipment operate properly? Turn OFF the power, remove the download jig and install the cover plate, the right upper cover-1 and the right upper cover-2. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 25...
  • Page 580 Is the updating data written on the ROM of the download jig properly? • Do the download jig and the equipment operate properly? Turn OFF the power, remove the download jig and install the RADF rear cover. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 26 05/11...
  • Page 581 *Connect the finisher interface cable with the equipment after removing the finisher rear cover. Connect the download jig with the jig connector on the finisher control PC board. Connector Fig.6-30 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 27...
  • Page 582 Is the DIP switch on the finisher control PC board set properly? Turn OFF the power, remove the download jig and return the DIP switch to the status before updating. Install the finisher rear cover. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 28...
  • Page 583 Turn OFF the power of the equipment. Remove the cover plate. Cover plate Fig.6-32 Connect the download jig with the jig connector (CN602) on the FAX board. Connector Fig.6-33 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 29...
  • Page 584 08-903: Engine ROM version <Updating Scanner ROM> 08-905: Scanner ROM version <Updating RADF ROM> 08-907: RADF ROM version <Updating Finisher ROM> 08-908: Finisher ROM version <Updating FAX ROM> 08-915: FAX ROM version e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 30...
  • Page 585: Firmware Updating With Download Jig (E-Studio202L/232/282)

    Refer to the following for the details to update with each download jig. P.6-33 "6.2.1 PWA-DWNLD-350-JIG2 (48 MB)" P.6-42 "6.2.2 Writing the data to the download jig (PWA-DWNLD-350-JIG)" June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 31 05/11...
  • Page 586 P.6-42 "6.2.2 Writing the data to the download jig (PWA-DWNLD-350-JIG)" K-PWA-DLM-320 Connector Mark for ROM installation direction Fig.6-35 Jig board: K-PWA-DLM-320 Important: Pay attention to the direction of the ROM. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 32 05/11...
  • Page 587: Pwa-Dwnld-350-Jig2 (48 Mb)

    Write the ROM data to be updated to the download jig. P.6-42 "6.2.2 Writing the data to the download jig (PWA-DWNLD-350-JIG)" Shut down the equipment. Remove the cover plate. Cover plate Fig.6-36 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 33 05/11...
  • Page 588 The screen for selecting the items to be updated is displayed. “*” is displayed next to the items to be updated. (All items are selected in the default settings.) e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 34 05/11...
  • Page 589 <Updating Scanner ROM> Select “4. Scanner Firmware Update” only. Example: Updating the system ROM (Updating all the items is taken as an example and explained in the following procedures.) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 35 05/11...
  • Page 590 Engine MAIN Update .. Completed Scanner Firm Update..Flash Update Scanner Firm Update.. Completed “Update Completed.” is displayed at the bottom of the LCD screen after the updating is com- pleted properly. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 36 05/11...
  • Page 591 08-923: UI data common section version 08-930: Version of UI data in FROM displayed at power ON <Updating Engine ROM> 08-903: Engine ROM version <Updating Scanner ROM> 08-905: Scanner ROM version June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 37 05/11...
  • Page 592: Os Update

    Turn ON the power while [8] button and [9] button are pressed simultaneously Select items to be updated and press the [START] button to start updating the [System ROM], [Engine ROM] and [Scanner ROM] in parallel. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 38 05/11...
  • Page 593 [UI Update] update will start. When the [System ROM]-[UI Update] has been updated, “UI Data Update…Completed” is dis- played and the [System Firmware Update] update will start. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 39 05/11...
  • Page 594: Sysfirm Update

    When the [Scanner ROM] has been updated, “Scanner Firm Update..Flash Update” is changed to “Scanner Firm Update..Com- pleted”. When all data has been updated, “Update Completed” is displayed. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 40 05/11...
  • Page 595 * “Update Failed.” is displayed at the bottom of the LCD screen when the updating is not completed properly. “Failed” appears next to the failed item on the status display. Failed items Error message June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 41 05/11...
  • Page 596: Writing The Data To The Download Jig (Pwa-Dwnld-350-Jig)

    (or equivalent) Minato Electronics MODEL 1893/1895/1931/1940 PWA-DL-ADP-350-1931 (model 1931) (or equivalent) model 1881 model 1931 ( LV650 ) [ PWA-DL-ADP-350-1881 ] [ PWA-DL-ADP-350-1931 ] Fig.6-39 PWA-DL-ADP-350-1881 Fig.6-40 PWA-DL-ADP-350-1931 e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 42 05/11...
  • Page 597 2.bin ROM3 ROM4 ROM5 ROM6 Note: Note: Be sure not to confuse different ROM Versions since the file name is identical although the ROM version is different. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 43 05/11...
  • Page 598: K-Pwa-Dlm-320

    Turn OFF the power before installing or removing the download jig. • Do not turn OFF the power during the update. The data could be damaged and not be oper- ated properly. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 44 05/11...
  • Page 599 Make sure the direction is correct (P.6-32 "Fig.6-35"). Turn OFF the power of the equipment. Take off the connector cover. Connector cover Fig.6-41 Remove the cover plate. Cover plate Fig.6-42 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 45 05/11...
  • Page 600 Is the updating data written on the ROM of the download jig properly? • Do the download jig and the equipment operate properly? Turn OFF the power, remove the download jig and install the cover plate and the connector cover. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 46 05/11...
  • Page 601 Make sure the direction is correct (P.6-32 "Fig.6-35"). Turn OFF the power of the equipment. Take off the right upper cover-1. Right upper cover-1 Fig.6-44 Take off the right upper cover-2. Right upper cover-2 Fig.6-45 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 47 05/11...
  • Page 602 Do the download jig and the equipment operate properly? Turn OFF the power, remove the download jig and install the cover plate, the right upper cover-1 and the right upper cover-2. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 48 05/11...
  • Page 603 Is the updating data written on the ROM of the download jig properly? • Do the download jig and the equipment operate properly? Turn OFF the power, remove the download jig and install the RADF rear cover. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 49 05/11...
  • Page 604 Connect the download jig with the jig connector on the finisher control PC board. Connector Fig.6-50 Change the setting of he DIP switch on the finisher control PC board. Change all the setting of the DIP switch (1-8) to OFF. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 50 05/11...
  • Page 605 Is the DIP switch on the finisher control PC board set properly? Turn OFF the power, remove the download jig and return the DIP switch to the status before updating. Install the finisher rear cover. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 51 05/11...
  • Page 606 Turn OFF the power of the equipment. Remove the cover plate. Cover plate Fig.6-52 Connect the download jig with the jig connector (CN602) on the FAX board. Connector Fig.6-53 e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 52 05/11...
  • Page 607 <Updating Scanner ROM> 08-905: Scanner ROM version <Updating RADF ROM> 08-907: RADF ROM version <Updating Finisher ROM> 08-908: Finisher ROM version <Updating FAX ROM> 08-915: FAX ROM version June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 53 05/11...
  • Page 608: Firmware Updating With Fsms (Field Service Manager) (E-Studio200L/230/280)

    When updating through USB (using FSMS), a printer driver needs to be installed in the PC in advance. Refer to the Printing Guide about the installation method of the printer driver. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 54 06/01...
  • Page 609 (SYS board) Engine ROM Logic PC board mfirm.tz (LGC board) Scanner ROM Scanning section control PC board scnfirm.tz (SLG board) NIC ROM NIC board nicfirm.tz June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 55...
  • Page 610 Mode (08) is recommended. Turn ON the power of the PC. Activate FSMS. Select “TOSHIBA FSMS” starting with the Start menu. Enter the login password and click the [OK] button. Fig.6-56 *Set the login password at the installation of FSMS.
  • Page 611 Click the [F/W Download] button. Fig.6-57 Select the model name of the equipment to be updated from the drop-down menu and click the [OK] button. Fig.6-58 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 57...
  • Page 612 The content of “Status” display can be renewed to the latest status by clicking the [Refresh] but- ton. When the status is displayed as “Disconnected” because the start up of the equipment is delayed, the status can be renewed to “Connected” by clicking this. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 58...
  • Page 613 Engine ROM mfirm.tz Scan ROM Scanner ROM scnfirm.tz NIC ROM NIC ROM nicfirm.tz Generic Master data uidata2.tz, uidata3.tz, uidata4.tz, uidata5.tz, uidata6.tz, uidata7.tz, webdata1.tz, webdata2.tz, webdata3.tz, webdata4.tz, webdata5.tz, webdata6.tz, all.tz June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 59...
  • Page 614 Select “File Name Conversion”. Click the [Browse] button of each data and select the file. When “Generic Driver” is used, check the checkbox of the file to be selected. Fig.6-63 e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 60...
  • Page 615 In this case, all the button operations are locked. (13) When the data transmission is completed, the following screen is displayed. Then click the [OK] button. Fig.6-66 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 61...
  • Page 616 (14) The equipment restarts automatically and the items to be updated and processing status are dis- played on the LCD screen. Fig.6-67 e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 62 04/09...
  • Page 617 Are the equipment and PC properly connected? • Is the selected data file proper? • Do the cable, equipment and PC operate properly? • Are FSMS and printer driver properly installed? Fig.6-69 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 63 04/09...
  • Page 618 OFF the power, and then restart updating from the beginning. If you turn OFF the power within 5 minutes, HDD may be destroyed. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 64 04/09...
  • Page 619 08-930: Version of UI data in FROM displayed at power ON <Updating Engine ROM> 08-903: Engine ROM version <Updating Scanner ROM> 08-905: Scanner ROM version <Updating NIC ROM> 08-916: NIC ROM version June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 65...
  • Page 620: Firmware Updating With Usb Storage Device (E-Studio200L/230/280)

    System control PC board sysfirm.bin, ROM.bin (SYS board) Engine ROM Logic PC board ROM.bin (LGC board) Scanner ROM Scanning section control PC board (SLG board) NIC ROM NIC board e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 66 05/11...
  • Page 621 Windows 95 and NT do not support USB. Be careful since the data can not be written on the devices in the PCs with these operating systems. Turn OFF the power of equipment. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 67...
  • Page 622 (GM-3020 or 3030) are used, the update must be performed after all the "don- gles" are disconnected from the USB connector (host) and only the USB storage device is connected. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 68...
  • Page 623 If the USB storage device is not recognized properly, the following message is displayed. In this case, turn OFF the power of the equipment and connect the device properly. Then repeat the procedure from (4). Fig.6-73 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 69...
  • Page 624 Select “4. NIC Firmware Update” only. Example: Updating the master data and system ROM (Updating the master data and system ROM is taken as an example and explained.) Fig.6-74 e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 70...
  • Page 625 Fig.6-75 “Update Completed.” is displayed at the bottom of the LCD screen after the updating is com- pleted properly. Fig.6-76 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 71...
  • Page 626 • Does the USB storage device meet the conditions to be used for updating ( P.6-66 "6.4 Firmware Updating with USB Storage Device (e-STUDIO200L/230/280)")? • Is the data file written properly on the USB storage device? •...
  • Page 627 OFF the power, and then restart updating from the beginning. If you turn OFF the power within 5 minutes, HDD may be destroyed. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 73...
  • Page 628 08-930: Version of UI data in FROM displayed at power ON <Updating Engine ROM> 08-903: Engine ROM version <Updating Scanner ROM> 08-905: Scanner ROM version <Updating NIC ROM> 08-916: NIC ROM version e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 74...
  • Page 629 When the device is recognized properly after 3 minutes, the screen for selecting items is dis- played. Press the [START] button after selecting the item to be updated. The device check starts. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 75...
  • Page 630 When all files have been copied, the backup of RIP font starts. When the backup of RIP font is completed, the following screen is displayed. Updating the mas- ter data is completed. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 76...
  • Page 631 The device check starts. When the device check completes, copying the data to the ROM of the equipment starts. When copying the data completes, copying the other data are implemented repeatedly. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 77...
  • Page 632 When copying all the data complete, the update completes with the following screen. * If the USB storage device is not recognized properly, the following message is displayed and the update is interrupted. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 78...
  • Page 633 * If an error occurs, the following error message is displayed and the update is interrupted. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 79...
  • Page 634: Firmware Updating With Usb Storage Device (E-Studio202L/232/282)

    8 MB. System ROM System control PC board firmImage0.bin, firmImage1.bin (SYS board) Engine ROM Logic PC board firmImage2.bin (LGC board) Scanner ROM Scanning section control PC board (SLG board) e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 80 05/11...
  • Page 635 Do not update the firmware by any storage device other than a flash memory (such as a USB connection type memory card reader, CD/DVD drive or hard disk) since it is never guaran- teed. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 81...
  • Page 636 (GM-4070 or GM-4080U) are used, the update must be performed after all the "dongles" are disconnected from the USB connector (host) and only the USB stor- age device is connected. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 82 05/11...
  • Page 637 2. UI Data Update firmImage0.bin is written. 3. System Firmware Update firmImage0.bin and firmImage1.bin are written. 4. Engine Firmware Update firmImage2.bin is written. 5. Scanner Firmware Update firmImage2.bin is written. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 83 05/11...
  • Page 638 In this case, turn OFF the power of the equipment and confirm if the data file stored in the USB storage device is correct. Then repeat the procedure from (4). e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 84 06/01...
  • Page 639 Select “5. Scanner Firmware Update” only. Example: Updating the master data and system ROM (Updating all the items is taken as an example and explained in the following procedures.) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 85...
  • Page 640 Engine MAIN Update .. Completed Scanner Firm Update.. Flash Update Scanner Firm Update.. Completed “Update Completed.” is displayed at the bottom of the LCD screen after the updating is com- pleted properly. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 86 05/11...
  • Page 641 Turn ON the power while [0] button and [8] button are pressed simultaneously. • Key in “947”, and then press the [START] button. • Press the [INITIALIZE] button. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 87 05/11...
  • Page 642 08-923: UI data common section version 08-930: Version of UI data in FROM displayed at power ON <Updating Engine ROM> 08-903: Engine ROM version <Updating Scanner ROM> 08-905: Scanner ROM version e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 88 05/11...
  • Page 643: Os Update

    [Engine ROM] [scanner ROM] 4. Engine 5. Scanner 0. OS Update 1. HDD Update Firmware Update Firmware Update 2. UI Data Update 3. System Firmware Update Update Completed June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 89 05/11...
  • Page 644 Select items to be updated and press the [START] button to start updating the [System ROM], [Master Data], [Engine ROM] and [Scanner ROM] in parallel. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 90 05/11...
  • Page 645 [UI Update] update will start. When the [System ROM]-[UI Update] has been updated, “UI Data Update…Completed” is dis- played and the [System Firmware Update] update will start. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 91 05/11...
  • Page 646: Hd Data Update

    Update] has been updated, “SysFirm Update…Completed” is displayed. Total files File name of master data Copies When the [Master Data] has been updated, “HD Data Update…Completed” is displayed. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 92 05/11...
  • Page 647: Scanner Firm Update

    When the [Scanner ROM] has been updated, “Scanner Firm Update..Flash Update” is changed to “Scanner Firm Update..Com- pleted”. When all data has been updated, “Update Completed” is displayed. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 93 05/11...
  • Page 648 * “Update Failed.” is displayed at the bottom of the LCD screen when the updating is not completed properly. “Failed” appears next to the failed item on the status display. Failed items Error message e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 94 05/11...
  • Page 649: Appendix

    Turn ON the power while [3] button and [CLEAR] button are pressed simultaneously. • The following screen is displayed. Fig.6-80 Select the item with the digital keys and press the [START] button. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING 6 - 95 05/11...
  • Page 650: E-Studio202L/232/282

    Turn ON the power while [3] button and [CLEAR] button are pressed simultaneously. • The following screen is displayed. Select the item with the digital keys and press the [START] button. e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING June 2004 © TOSHIBA TEC 6 - 96 05/11...
  • Page 651: Power Supply Unit

    Output to the SLG board 4) -12V -12VA CN705 Pin 9 Output to the SYS board -12VB CN705 Pin 3 Output to the SYS board 5) +24V +24VB Not used June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 POWER SUPPLY UNIT 7 - 1...
  • Page 652 LGC board), PFP/LCF (via LGC board), Bridge unit / Job separator / Offset tray (via LGC board) CN707 For the ADU board, finisher +24VD1, +24VD2, +24VD5 CN708 For the SLG board, RADF +24VD3, +24VD4 e-STUDIO200L/202L/230/232/280/282 POWER SUPPLY UNIT June 2004 © TOSHIBA TEC 7 - 2...
  • Page 653: Fuse

    Bridge unit / Job separator / Offset tray +24VD3 RADF F6:4A (Semi time-lag) +24VD4 Scan motor F7:4A (Semi time-lag) Exposure lamp (Lamp inverter) +24VD5 Finisher F8:5A (Semi time-lag) June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 POWER SUPPLY UNIT 7 - 3...
  • Page 654: Configuration Of Power Supply Unit

    Configuration of Power Supply Unit Fig.7-1 e-STUDIO200L/202L/230/232/280/282 POWER SUPPLY UNIT June 2004 © TOSHIBA TEC 7 - 4 05/11...
  • Page 655: Remote Service

    3) If Order Failure Occurs If some problems occur and the order cannot be placed after registering an order as a job, refer to the standard countermeasure for the FAX/E-mail transmission failure. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE 8 - 1...
  • Page 656: Setting Item

    1: Valid (FAX/Internet FAX/HTTP)* 2: Invalid (Default) When changing the setting value from “2” (default) to “0”, the Auto Supply Order setting screen is displayed. (* HTTP has not been supported yet.) e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE June 2004 © TOSHIBA TEC 8 - 2...
  • Page 657 *2 Even when “FAX” is selected, the order is not placed without entering the FAX number. *3 Even when “MAIL” is selected, the order is not placed without entering the E-mail address. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE...
  • Page 658 3) Output of setting list of the Auto Supply Order Keying in the following buttons and keys prints the setting list. [USER FUNCTIONS] [USER] [LISTS] [*] [#] [*] [*] [3] [8] [START] e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE June 2004 © TOSHIBA TEC 8 - 4...
  • Page 659: Setting Procedure

    Press the [PASSWORD] button and the screen is switched to a full keyboard. Then key in the Administrator Password and press the [ENTER] button. * Confirm the password to the administrator. Fig.8-2 Press the [SERVICE] button in the ADMIN screen. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE 8 - 5 05/05...
  • Page 660 The SERVICE screen is displayed. Fig.8-3 Press the [SUPPLY ORDER SETUP] button. Fig.8-4 Press the [ORDER INFORMATION] button. (10) The ORDER INFORMATION screen is displayed. Fig.8-5 e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE June 2004 © TOSHIBA TEC 8 - 6...
  • Page 661 [E-MAIL] --- Input the E-mail address of customer. [ADDRESS] --- Input the address of customer. SUPPLIER [NAME] --- Input the name of supplier. [ADDRESS] --- Input the address of supplier. (15) Press the [NEXT] button. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE 8 - 7...
  • Page 662 [OFF] / [ALWAYS] / [ON ERROR] --- Whichever you press, the result list is printed. (18) Press the [ENTER] button to register and complete the order information setting. (19) The SERVICE screen is returned. Fig.8-8 e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE June 2004 © TOSHIBA TEC 8 - 8 05/05...
  • Page 663 (20) Press the [SUPPLY ORDER SETUP] button. Fig.8-9 (21) Press the [TONER ORDERING] button. (22) The TONER ORDERING screen is displayed. Fig.8-10 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE 8 - 9...
  • Page 664 (27) Press the [USER FUNCTION] button to be switched from the ADMIN screen on touch panel and returned to the BASIC screen, so that the setting of Auto Supply Order is finished. e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE June 2004 © TOSHIBA TEC 8 - 10 05/05...
  • Page 665 Maximum 128 letters [DESCRIPTION] RESULT PRINTING 0: OFF [OFF] / [ALWAYS] / [ON ERROR] 1: Always 2: ON Error TONER Maximum 20 digits [PART NUMBER] TONER 1-99 [CONDITION] TONER 1-99 [QUANTITY] June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE 8 - 11...
  • Page 666: Order Sheet Format

    Device FAX Number: 1122 Device Email: [email protected] OrderInformation: BLACK PartNumber: kuro-01 Quantity: 1 CounterInformation: PrintCounter(Small) FullColor: 0 TwinColor:0 Black:5 PrintCounter(Large) FullColor: 0 TwinColor:0 Black:0 ScanCounter FullColor: 0 TwinColor: 0 Black: 0 Fig.8-13 e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE June 2004 © TOSHIBA TEC 8 - 12...
  • Page 667 BLACK : XXXXXXXXXXXX DESCRIPTION AREA ....................... DEVICE DESCRIPTION :XXXXXXXXXXXXXXXXXXXXXXX SERIAL NUMBER :XXXXXXXXXXXXXXXXXXXXXXX DEVICE FAX NUMBER :XXXXXXXXXXXXXXXXXXXXXXX DEVICE E-MAIL ADDRESS :XXXXXXXXXXXXXXXXXXXXXXX TOTAL PRINT COUNTER 999999999 SCAN COUNTER 999999999 Fig.8-14 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE 8 - 13...
  • Page 668: Service Notification

    The screen to set this function is not displayed at the default setting. Set this screen to be displayed with the following code (08). 08-774 Setting of notification display 0: Invalid (Default) 1: Valid e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE June 2004 © TOSHIBA TEC 8 - 14 05/05...
  • Page 669 Press the [USER FUNCTIONS] button and select the [ADMIN] button. Then enter the password and press the [ENTER] button. • Confirm the password to the administrator. Fig.8-15 Press the [SERVICE] button. Fig.8-16 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE 8 - 15 05/05...
  • Page 670 Press the [SERVICE NOTIFICATION] button. Fig.8-17 Press the [E-MAIL] or [FAX] button in “SERVICE NOTIFICATION”. • When the [OFF] button is pressed, all functions related Service Notification become ineffec- tive. Fig.8-18 e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE June 2004 © TOSHIBA TEC 8 - 16 05/05...
  • Page 671 E-mail addresses and press the [ENTER] button. (Maximum 3 addresses can be set.) Fig.8-19 • Press the [FAX NUMBER] button, key in the FAX number and then press the [ENTER] button. Fig.8-20 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE 8 - 17 05/05...
  • Page 672 1 to 31 Total counter transmission interval setting 00:00-23:59 (Hour/Hour/Minute/Minute) Service Call Transmit setting 0: OFF (Invalid) 1: ON (Valid) PM Counter Transmit setting 0: OFF (Invalid) 1: ON (Valid) e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE June 2004 © TOSHIBA TEC 8 - 18 05/05...
  • Page 673: Items To Be Notified

    1) Total Counter Transmit / PM Counter Transmit by E-mail (XML file attached to E-mail has also the same format.) Subject: Counter Notification (In case of the PM Counter Transmit, it is shown as “Periodical Maintenance Notification”.) Date : 07/11/2004 15:54 Machine Model : TOSHIBA e-STUDIO280 Serial Number : 1234567890 Total Counter : 00300000 ChargeCounterFormat:...
  • Page 674 Number of received pages in the FAX Function PM count setting value PM count present value PM driving count setting value PM driving count present value History of error *1 The latest 20 errors are displayed. e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE June 2004 © TOSHIBA TEC 8 - 20...
  • Page 675 *1 In case of the PM Counter Transmit, the title is replaced to “PERIODICAL MAINTENANCE NOTIFICATION”. COUNTER NOTIFICATION (*1) DATE : 05/03/10 13:47 MACHINE MODEL : TOSHIBA e-STUDIO280 SERIAL NUMBER : 1234567890 TOTAL COUNTER : 00004787 CHARGE COUNTER FORMAT PM COUNTER FORMAT...
  • Page 676 PM count setting value PM count present value PM driving count setting value PM driving count present value History of error *2 The latest 20 errors are displayed. e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE June 2004 © TOSHIBA TEC 8 - 22 05/05...
  • Page 677 Serial number Function: Fixed at “Print” Severity: Fixed at “Error” Error code Error message: The content of error is displayed. History of error *1 The latest 20 errors are displayed. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE 8 - 23...
  • Page 678 REMOTE SERVICE June 2004 © TOSHIBA TEC 8 - 24...
  • Page 679 However, the total counter is not copied. • Delete the backed up data in the USB storage device after the data cloning. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) 9 - 1 05/11...
  • Page 680 (GM-4070 or GM-4080U) are used, the data must be backed up after all the "dongles" are disconnected from the USB connector (host) and only the USB storage device is connected. e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) June 2004 © TOSHIBA TEC 9 - 2...
  • Page 681 "*". (The items "4", "5" and "6" are selected in the screen by default.) Fig. 9-3 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) 9 - 3 05/11...
  • Page 682 < Backing up User management information> Select "6: User Info" only. E.g.: In case of backing up the department management and user management information Fig. 9-4 e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) June 2004 © TOSHIBA TEC 9 - 4 05/11...
  • Page 683 (10) "Back Up Completed" is displayed on the LCD screen when the backup has been properly com- pleted. Fig. 9-6 (11) Turn the power OFF and remove the USB storage device. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) 9 - 5 05/11...
  • Page 684 The screen to select the setting backup item is displayed. In this screen, the items to be backed up are shown after the mark "*". (No items are selected in the screen by default.) Fig. 9-8 e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) June 2004 © TOSHIBA TEC 9 - 6...
  • Page 685 (The following screens are given as an example of when all TopAccess items are backed up.) (16) Press the [Start] button. The backup starts and the backing up status is displayed on the LCD screen. Fig. 9-9 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) 9 - 7 05/11...
  • Page 686 The screen to select the backup/restore items is displayed. Fig. 9-11 Note: Note: After the item is selected with the digital keys, displaying the next menu may take a long time. e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) June 2004 © TOSHIBA TEC 9 - 8 05/11...
  • Page 687 (The following screens are given as an example of when SRAM data are backed up.) (23) Press the [Start] button. The backup starts and the backing up status is displayed on the LCD screen. Fig. 9-13 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) 9 - 9 05/11...
  • Page 688 (24) "Back Up Completed" is displayed on the LCD screen when the backup has been properly com- pleted. Fig. 9-14 (25) Turn the power OFF and remove the USB storage device. e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) June 2004 © TOSHIBA TEC 9 - 10 05/11...
  • Page 689 (GM-4070 or GM-4080U) are used, the data must be restored after all the "dongles" are disconnected from the USB connector (host) and only the USB storage device is connected. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) 9 - 11 05/11...
  • Page 690 The screen to select the user data restore item is displayed. In this screen, the items to be restored are shown after the mark "*". (The items "4", "5" and "6" are selected in the screen by default.) Fig. 9-17 e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) June 2004 © TOSHIBA TEC 9 - 12 05/11...
  • Page 691 <Restoring User management information> Select "6: User Info" only. E.g.: In case of restoring the department management and user management information Fig. 9-18 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) 9 - 13 05/11...
  • Page 692 [COUNTER] o [DEPARTMENT SETTING] o Enter the password o [RESET ALL COUNTERS] * Enable the department management when the [RESET ALL COUNTERS] button is set to be disabled. e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) June 2004 © TOSHIBA TEC 9 - 14...
  • Page 693 The screen to select the setting restore item is displayed. In this screen, the items to be restored are shown after the mark "*". (No items are selected in the screen by default.) Fig. 9-22 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) 9 - 15 05/11...
  • Page 694 (The following screens are given as an example of when all TopAccess items are restored.) (15) Press the [Start] button. The restore starts and the restoring status is displayed on the LCD screen. Fig. 9-23 e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) June 2004 © TOSHIBA TEC 9 - 16 05/11...
  • Page 695 The screen to select the backup/restore items is displayed. Fig. 9-25 Note: Note: After the item is selected with the digital keys, displaying the next menu may take a long time. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) 9 - 17 05/11...
  • Page 696 (The following screens are given as an example of when SRAM data are restored.) (22) Press the [Start] button. The restore starts and the restoring status is displayed on the LCD screen. Fig. 9-27 e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) June 2004 © TOSHIBA TEC 9 - 18 05/11...
  • Page 697 (23) "Restore Completed" is displayed on the LCD screen when the restore has been properly com- pleted. Fig. 9-28 (24) Turn the power OFF and remove the USB storage device. June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) 9 - 19 05/11...
  • Page 698 Checksum error ERROR 8 Model check error ERROR 9 Version check error ERROR 10 Destination check error ERROR 11 Serial number check error e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) June 2004 © TOSHIBA TEC 9 - 20 05/11...
  • Page 699 Date: MON SEP 26 18:34:40 2005 • File format (user_data.txt, setting_data.txt, sram_data.txt: all in common) Line 1: Version Line 2: Serial number Line 3: Date June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) 9 - 21 05/11...
  • Page 700 DATA CLONING with USB STORAGE DEVICE (e-STUDIO202L/232/282) June 2004 © TOSHIBA TEC 9 - 22...
  • Page 701: Ac Wire Harness

    10. WIRE HARNESS CONNECTION DIAGRAMS 10.1 AC Wire Harness Fig.10-1 June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 WIRE HARNESS CONNECTION DIAGRAMS 10 - 1 05/11...
  • Page 702 WIRE HARNESS CONNECTION DIAGRAMS June 2004 © TOSHIBA TEC 10 - 2...
  • Page 703 10.2 DC Wire Harness (e-STUDIO200L/230/230L/280/280S) 05/11...
  • Page 704 10.3 Connector Table (e-STUDIO200L/230/230L/280/280S) CN301 PWA-F-LGC (CN301) <-> COIN CONTROLLER (OPTION)/ CN308 PWA-F-LGC (CN308) <-> PS-HVT (CN720)/THMS-C-HTR, CN112 PWA-F-SYS (CN112) <-> HDD (CN170) (STANDARD) CN121 PWA-F-SYS (CN121) <-> PWA-F-NIC (J3) PWA-F-SLG (CN1) <-> PWA-F-CCD (CN14) CN501 FAX (CN501) <-> NCU (1) (OPTION)
  • Page 705 10.4 DC Wire Harness (e-STUDIO202L/232/282) 05/11...
  • Page 706 10.5 Connector Table (e-STUDIO202L/232/282) CN301 PWA-F-LGC (CN301) <-> COIN CONTROLLER (OPTION)/ CN310 PWA-F-LGC (CN310) <-> PFP (OPTION)/LCF (OPTION) CN105 PWA-F-SYS (CN105) <-> DDR DIMM CN115 PWA-F-SYS (CN115) <-> USB CONNECTOR (DEVICE) PWA-F-SLG (CN1) <-> PWA-F-CCD (CN14) J422 PWA-F-DSP (J422) <-> LCD PANEL COPY KEY CARD (OPTION) Pin No Symbol...

Table of Contents

The caption "" was not found. Please press the button below to search within the manual content.