Page 1: Dvd Player
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936...
Page 2: Safety Information
The use of a substitute replacement component which does Leakage 0.5mA current Device not have the same safety characteristics as the PIONEER tester under recommended replacement one, shown in the parts list in test this Service Manual, may create shock, fire, or other hazards.
Page 3 KEYB assy), with the above requirements satisfied. 2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. ∗ : See page 87. (Printed on the Rear Panel) WYXJ5 KUCXJ DVD-V8000...
Page 4: Dvd-V8000 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DVD-V8000...
Page 5 When downloading the firmware If you download the firmware via the RS-232C serial port after failing to upgrade it using the CD-R disc, settings, such as SETUP, ADV.SETUP, and the command stack, are all reset to default. • See "7. GENERAL INFORMATION." DVD-V8000...
Page 6: Table Of Contents
7.8.1 IC ..............................130 7.8.2 LCD MODULE ..........................158 7.9 DISC / CONTENT FORMAT PLAYBACK COMPATIBILITY ..............159 8. PANEL FACILITIES ............................160 9. RACK MOUNT KIT (CB-A802) ........................164 9.1 PACKING SECTION ..........................164 9.2 INSTALLATION PROCEDURES ......................166 DVD-V8000...
Page 7: Specifications
(AUDIO OUT L, R) Ω Digital .........Pin jack x 1, 0.5 Vp-p, 75 (DIGITAL AUDIO OUT COAXIAL) Optical fiber connector x 1 (DIGITAL AUDIO OUT OPTICAL) The specifications and design of this product are subject to change without notice, due to improvement. DVD-V8000...
Page 8: Exploded Views And Parts List
Screws adjacent to mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING (/KUCXJ) (/WYXJ5) DVD-V8000...
Page 9 DHA1719 Instruction Manual DRE1031 (English, French) > Power Cord See contrast table (2) (2) CONTRAST TABLE DVD V8000/KUCXJ and DVD-V8000/WYXJ5 are construccted the same except for following: DVD-V8000 DVD-V8000 Mark No. Symbol and Description /KUCXJ /WYXJ5 4 Packing Case DHG2601 DHG2600 >...
Page 10: Exterior Section
2.2 EXTERIOR SECTION Refer to "2.4 LOADER MECHA ASSY". 10 6 Refer to "2.3 FRONT PANEL SECTION". DVD-V8000...
Page 11 Mecha Case (Side) DNH2727 Barrier DNH2758 Adapter 3 L (ABS) VNL1958 Adapter 3 R (ABS) VNL1959 (2) CONTRAST TABLE DVD-V8000/KUCXJ and DVD-V8000/WYXJ5 are construccted the same except for following: DVD-V8000 DVD-V8000 Mark No. Symbol and Description /KUCXJ /WYXJ5 18 Rear Panel DNC1781...
Page 12: Front Panel Section
2.3 FRONT PANEL SECTION DVDM CN1502 DVDM Solder DVDM CN1501 the No."4" together CN1504 with the No."7". DVD-V8000...
Page 13 Connector Assy DKP3746 Connector Assy DKP3747 LCD Module DWG1590 Tray Packing C DEC2896 Tray Packing D DEC2897 EMI Sheet A DEC2959 Display Sheet A DEC2971 Display Sheet B DEC2972 Display Window DAH2429 Front Panel Assy DXA2066 Screw BPZ30P080FCC Screw IPZ30P080FTC DVD-V8000...
Page 14: Loader Mecha. Assy
LOAB Assy VWG2426 Floating Rubber VEB1351 Connector Assy (2P) VKP2253 Belt VEB1358 Stabilizer VNE2253 Loading Base VNL1917 Float Base DVD VNL1918 Drive Cam VNL1919 Gear Pulley VNL1921 Loading Gear VNL1922 Drive Gear VNL1923 SW Lever VNL1925 Clamper Plate VNE2342 DVD-V8000...
Page 15 Rear View Daifree Daifree No. 21 No. 21 GEM1036 GEM1036 Tray Tray Concave of unevenness Concave of unevenness Inner side of a ditch Daifree GEM1036 Top View Bottom View Side of the rib Concave of unevenness Daifree Daifree GEM1036 GEM1036 DVD-V8000...
Page 16: Traverse Mecha. Assy-S
15 (Torque : 0.15 ± 0.01 N•m) Silicone Adhesive GEM1037 DVDM CN101 (Pickup Assy) 4 (Adjustment screw) Silicone Adhesive GEM1037 Screw Tight 15 (Torque : 0.15 ± 0.01 N•m) GYL1001 (Adjustment spring) To DVDM CN105 (Spindle Motor) DVDM CN104 (Stepping Motor) DVD-V8000...
Page 17 VBA1091 Skew Spring VBH1335 Guide Bar VLL1514 Sub Guide Bar VLL1515 Leaf Spring VNC1023 Joint Spring VNC1019 Support Spring VNC1020 NSP 11 Mecha.Chassis VNE2344 Damper Sheet VEB1335 Spacer VNL1913 Joint 03 VNL1949 Tapping Screw VBA1092 Screw BBZ20P050FTC Screw PMA26P100FTC DVD-V8000...
Page 18: Block Diagram And Schematic Diagram
CN9002 123456789012 IC9001 IR Key Lock LED POWER_SW POWER_LED PWSB ASSY V+5E STANDBY LED Disp KEY LCD KEY KEYB ASSY PLAY LED POWER KEY ON LED Play/Pouse Key KEY Stop/Open KEY SCAN/SKIP KEY STILL/STEP KEY SELECT_M KEY SELECT_V KEY DVD-V8000...
Page 19 CN9701 0.22Fx 2 superC Keyin1 ~ 4 Keyout1 ~ 5 6dB UP R IN USBB ASSY IC8801 6dB UP REL_DA S-35190A REL_CK EXT SYNC IN X8801 REL_CS 32.768 kHz USB(MOUSE,MEMORY) AJKB ASSY EXT SYNC IN SELECT_A KEY LECT_V KEY DVD-V8000...
Page 20: Loab Assy And Overall Wiring Diagram
3.2 LOAB ASSY and OVERALL WIRING DIAGRAM LCD MODULE (DWG1590) USBB ASSY (DWZ1179) SYPS ASSY (DWR1401) 1/6 - DVDM ASSY (DWS1364) AJKB ASSY (DWZ1176) DVD-V8000...
Page 21 ÷ The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when VJKB ASSY (DWZ1175) replacing, be sure to use parts of identical designation. ÷ : The power supply is shown with the marked box. DVD-V8000...
Page 22: Dvdm Assy 1/6 [Fts Block]
SCH diagram (RF) : RF SIGNAL ROUTE (RF_V) : RF (VIDEO) SIGNAL ROUTE (RF_A) : RF (AUDIO) SIGNAL ROUTE (AD) : AUDIO DATA SIGNAL ROUTE : FOCUS SERVO LOOP LINE : TRACKING SERVO LOOP LINE : STEPPING SERVO LOOP LINE DVD-V8000...
Page 23 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram and PCB diagram. 1/6, DVD-V8000...
Page 24 DVDM ASSY (DWS1364) (2/2) Large size SCH diagram NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram and PCB diagram. DVD-V8000...
Page 25 (AD) (RF) : RF SIGNAL ROUTE (RF_V) : RF (VIDEO) SIGNAL ROUTE (RF_A) : RF (AUDIO) SIGNAL ROUTE (AD) : AUDIO DATA SIGNAL ROUTE : FOCUS SERVO LOOP LINE : TRACKING SERVO LOOP LINE : STEPPING SERVO LOOP LINE DVD-V8000...
Page 26: Dvdm Assy 2/6 [Fr Block]
3.4 DVDM ASSY 2/6 [FR BLOCK] DVDM ASSY (DWS1364) (1/2) Large size SCH diagram DVD-V8000...
Page 27 DVD-V8000...
Page 28 DVDM ASSY (DWS1364) (2/2) CN101 DVD-V8000...
Page 29 TC7W53FU-TRB Large size SCH diagram DVD-V8000...
Page 30: Dvdm Assy 3/6 [Eby/Av1 Block]
3.5 DVDM ASSY 3/6 [EBY/AV1 BLOCK] DVDM ASSY (DWS1364) (1/2) Large size SCH diagram DVD-V8000...
Page 31 (VD) (AD) (RF_V) : RF (VIDEO) SIGNAL ROUTE (VD) : VIDEO DATA SIGNAL ROUTE (AD) : AUDIO DATA SIGNAL ROUTE : AUDIO (DIGITAL) SIGNAL ROUTE DVD-V8000...
Page 32 DVDM ASSY (DWS1364) (2/2) Large size SCH diagram DVD-V8000...
Page 33 (AD) (VD) (VD) (RF_V) : RF (VIDEO) SIGNAL ROUTE (VD) : VIDEO DATA SIGNAL ROUTE (AD) : AUDIO DATA SIGNAL ROUTE : AUDIO (DIGITAL) SIGNAL ROUTE DVD-V8000...
Page 34: Dvdm Assy 4/6 [Video Block]
: VIDEO DATA SIGNAL ROUTE : V SIGNAL ROUTE (S_Y) : S_Y SIGNAL ROUTE (S_C) : S_C SIGNAL ROUTE Large size : Y SIGNAL ROUTE SCH diagram (Cb) : Cb SIGNAL ROUTE (Cr) : Cr SIGNAL ROUTE (VD) (VD) (VD) (VD) DVD-V8000...
Page 35 (VD) DVD-V8000...
Page 36 (VD) : VI (S_Y) : S_ (S_C) (VD) : S_ (Cb) : Cb (VD) (Cr) (VD) Large size SCH diagram CN7001 DVD-V8000...
Page 37 DVDM ASSY (DWS1364) (2/2) (VD) : VIDEO DATA SIGNAL ROUTE : V SIGNAL ROUTE (S_Y) : S_Y SIGNAL ROUTE (S_C) : S_C SIGNAL ROUTE : Y SIGNAL ROUTE (Cb) : Cb SIGNAL ROUTE (VD) (Cr) : Cr SIGNAL ROUTE (VD) DVD-V8000...
Page 38: Dvdm Assy 5/6 [Usb/Subcpu Block]
3.7 DVDM ASSY 5/6 [USB/SUBCPU BLOCK] DVDM ASSY (DWS1364) (1/2) Large size SCH diagram : AUDIO (DIGITAL) SIGNAL ROUTE CN8001 DVD-V8000...
Page 39 CN9701 DVD-V8000...
Page 40 CN8701 DVDM ASSY (DWS1364) (2/2) Large size SCH diagram CN9001 DVD-V8000...
Page 41 UDZS5R6(B)-TRB DVD-V8000...
Page 42: Dvdm Assy 6/6
3.8 DVDM ASSY 6/6 DVDM ASSY (DWS1364) DVD-V8000...
Page 43 DVD-V8000...
Page 44: Vjkb And Usbb Assys
CN901 Large size SCH diagram CN1201 : V SIGNAL ROUTE (S_Y) : S_Y SIGNAL ROUTE (S_C) : S_C SIGNAL ROUTE : Y SIGNAL ROUTE (Cb) : Cb SIGNAL ROUTE (Cr) : Cr SIGNAL ROUTE (Ex_V) : Ex_VIDEO SIGNAL ROUTE DVD-V8000...
Page 45 CN901 DVD-V8000...
Page 46 VJKB ASSY (DWZ1175) (2/2) : V SIGNAL ROUTE (S_Y) : S_Y SIGNAL ROUTE (S_C) : S_C SIGNAL ROUTE : Y SIGNAL ROUTE (Cb) : Cb SIGNAL ROUTE (Cr) : Cr SIGNAL ROUTE (Ex_V) : Ex_VIDEO SIGNAL ROUTE Large size SCH diagram DVD-V8000...
Page 47 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram and PCB diagram. DVD-V8000...
Page 48: Ajkb Assy
3.10 AJKB ASSY AJKB ASSY (DWZ1176) (1/2) CN551 Large size SCH diagram : AUDIO (DIGITAL) SIGNAL ROUTE (L/R) : AUDIO (ANALOG) SIGNAL ROUTE (ExL/ExR) : Ex_AUDIO SIGNAL ROUTE DVD-V8000...
Page 49 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram and PCB diagram. CN1503 DVD-V8000...
Page 50 : AUDIO (DIGITAL) SIGNAL ROUTE AJKB ASSY (L/R) : AUDIO (ANALOG) SIGNAL ROUTE (DWZ1176) (2/2) (ExL/ExR) : Ex_AUDIO SIGNAL ROUTE Large size SCH diagram NOTE: DVD-V8000...
Page 51 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram and PCB diagram. DVD-V8000...
Page 52: Keyby And Pwsb Assys
3.11 KEYBY and PWSB ASSYS KEYB ASSY (DWZ1177) CN9501 DVD-V8000...
Page 53 PWSB ASSY (DWZ1178) DVD-V8000...
Page 54: Syps Assy
3.12 SYPS ASSY SYPS ASSY (DWR1401) [Figure of reference] • This assembly has no service part. • Please exchange assembly. LIVE NEUTRAL DVD-V8000...
Page 55 DVD-V8000...
Page 56: Waveforms
AC MODE DC MODE AC MODE CN901-pin28 (Cr) [PROGRESSIVE] IC201-pin39 (EFMIN) IC701-pin143 (PPWM) CN901-pin24 (Y) [INTERLACE] V:200 mV/div. H:10 µsec/div. V:0.5 V/div. H:0.2 µsec/div. V:200 mV/div. H:10 µsec/div. V:1 V/div. H:0.2 msec/div. AC MODE AC MODE DC MODE DC MODE DVD-V8000...
Page 57: Dvdm Assy
DC MODE CN551-pin7 (BCK) DC MODE IC7302-pin2 (MO2) DC MODE IC8204-pin7 (L3) V:1000 mV/div. H:0.1 µsec/div. V:500 mV/div. H:10 µsec/div. V:2000 mV/div. H:0.5 msec/div. CN551-pin5 (DATA) DC MODE V:1000 mV/div. H:5 µsec/div. CN551-pin3 (LRCK) DC MODE V:1000 mV/div. H:5 µsec/div. DVD-V8000...
Page 58 DVD-V8000...
Page 59: Pcb Connection Diagram
SIDE B P.C.Board Chip Part transistor Resistor array 3-terminal regulator SIDE A SIDE B LOAB ASSY (VNP1912-A) LOAB S101 LOAD+ VWG2426- CN602 CN602 C102 LOAD- PYKC F6 VNP1912- C101 CN601 CN601 CN602 CN601 CN601 CN602 CN103 LOADING MOTOR ASSY DVD-V8000...
Page 60: Dvdm Assy
4.2 DVDM ASSY SIDE A DVDM ASSY LOAB SPINDLE CARRIAGE CN601 MOTOR MOTOR SYSTEM CN115 CN114 CN111 CN103 CN1201 CN9701 DVD-V8000...
Page 61 Q106 IC1504 IC1001 Q104 IC304 IC1051 IC1502 Q1504 IC601 IC410 Q1056 IC1501 Q1052 IC1201 IC473 IC1204 IC1203 IC1505 IC701 IC481 IC474 IC411 Q1301 25 26 IC1301 (DNP2203-B) CN551 CN1503 CN8001 CN8701 NOTE : The encircled numbers denote measuring point. DVD-V8000...
Page 62 R410 C226 R761 C797 R766 L786 C787 C1209 R1210 R786 C781 C756 R787 C785 C798 R1214 R788 IC786 R789 C779 R452 C771 C761 C758 C757 C765 C766 C772 L763 CN1503 CN551 NOTE : The encircled numbers denote measuring point. DVD-V8000...
Page 63 R1552 C226 C1509 R1515 D1506 D1508 R1584 Q1508 C797 L786 IC1503 L1503 IC1503 R1241 R786 C1224 R1238 R1240 IC781 L1244 R1239 R787 IC1202 R1514 R788 D1501 IC786 IC741 R789 IC741 R1243 R1513 C747 C746 C748 C745 C1222 (DNP2203-B) CN1201 DVD-V8000...
Page 64: Ajkb Assy
R8702 D8711 D8710 D8712 D8713 C8733 X8801 D8718 D8722 D8720 C8734 C8725 D.LOAD C8732 DTR0 RxD0 TxD0 RxD1 TxD1 DTR1 JA8701 CN8702 CN8703 KN8001 IC8802 IC8601 Q8701 Q8710 Q8703 Q8709 Q8707 Q8705 IC8703 IC8801 Q8704 Q8702 Q8708 Q8706 IC8701 DVD-V8000...
Page 65 D8505 JA8505 Q8315 C8734 C8725 D8507 VR8501 JA8504 D8506 D8503 JA8503 D8502 S8701 (DNP2204-B) Q8701 IC8101 IC8203 IC8202 IC8205 Q8501 Q8301 Q8303 Q8201 Q8302 Q8304 Q8311 Q8313 Q8312 Q8314 Q8305 Q8315 NOTE : The encircled numbers denote measuring point. DVD-V8000...
Page 66 SIDE B AJKB ASSY 0 1 2 3 0 1 2 3 4 5 6 7 8 9 DVD-V8000...
Page 67 SIDE B (DNP2204-B) DVD-V8000...
Page 68: Vjkb And Usbb Assys
4.4 VJKB and USBB ASSYS SIDE A VJKB ASSY IC7301 IC7201 IC7202 IC7101 IC7701 Q7701 IC7601 Q7901 IC7302 Q7904 NOTE : The encircled numbers denote measuring point. DVD-V8000...
Page 69 SIDE A USBB ASSY KN9701 JA9702 GND +5V_U1 +5V_U2 V+3D CN9701 CN901 DWZ1179- USBB (DNP2204-B) CN9701 CN1201 (DNP2204-B) 7701 IC7601 DVD-V8000...
Page 70 SIDE B VJKB ASSY DVD-V8000...
Page 71 SIDE B USBB ASSY (DNP2204-B) CN9701 (DNP2204-B) DVD-V8000...
Page 72: Keyb And Pwsb Assys
DWM2262- FRKB DNP2235- CN9001 CN9002 1.SEL_A_LED 7.IR 13.GND 19.PLAY 2.KEY_IN1 8.KEY_IN4 14.KEY_OUT3 20.V+5E 1.GND D9005 3.SEL_V_LED 9.V+3E 15.GND 21.KEYL 2.POWER_SW 4.KEY_IN2 10.KEY_OUT1 16.KEY_OUT4 22.POWE 3.POWER_LED 5.SEL_M_LED 11.GND 17.GND 23.V+5D 4.V+5E 6.KEY_IN3 12.KEY_OUT2 18.KEY_OUT5 24.POWE S9044 S9043 S9042 S9041 S9031 DVD-V8000...
Page 73 N1504 MENU S9011 90001 S9023 S9021 ENTER UPPER 9002 S9015 S9014 S9013 SETUP RETURN S9025 S9022 S9024 S9012 19.PLAY_LED KEY_OUT3 20.V+5E 21.KEYLOCK_LED KEY_OUT4 22.POWER_LED 23.V+5D KEY_OUT5 24.POWER_SW D9001 D9002 D9003 MONITOR VIDEO AUDIO S9031 S9032 S9033 S9034 S9035 (DNP2235-A) DVD-V8000...
Page 74 SIDE B KEYB ASSY Q9503 Q9502 0 1 2 3 0 1 2 3 4 5 6 7 8 9 Q9501 MENU TOP MENU ENTER RETURN SETUP Q9015 Q9005 Q9013 Q9012 Q9011 Q9004 Q9014 Q9001 Q9003 Q9002 AUDIO VIDEO MONITOR DVD-V8000...
Page 75 SIDE B PWSB ASSY R9502 Q9503 Q9502 Q9501 R9503 C9503 R9501 DWZ1178- PWSB (DNP2235-A) CN9501 CN90001 KEY LOCK DISPLAY DWZ1177- KEYB CN9002 1.GND 2.POWER_SW 3.POWER_LED DWM2262- FRKB 4.V+5E DNP2235- (DNP2235-A) DVD-V8000...
Page 76: Syps Assy
4.6 SYPS ASSY SIDE A SIDE B SYPS ASSY [DWR1401] AC INLET ASSY CN101 CN101 CN401 DVD-V8000...
Page 77: Pcb Parts List
COILS AND FILTERS > IC0405 NJM2880U1-05 L1051–L1054 ATH7022 IC1506 NJM2904M L0481, L0482, L0600, L0601, L0603 CTF1305 L0608, L0701, L0718, L0721, L0728 CTF1305 IC1001 PD0280B L0741, L0756–L0760, L0763, L0786 CTF1305 IC0601 PD6345A L0907, L0916, L0919, L0921, L0923 CTF1305 IC0701 PE5286B DVD-V8000...
Page 78 CKSRYF104Z25 R0132 RS1/16S4702F C1070, C1071, C1507 CKSRYF104Z25 C0112, C0118, C0122, C0125, C0126 CKSRYF105Z10 R0357, R0362, R0363, R0368, R0372 RS1/16S6802F C0129-C0131, C0200, C0202, C0204 CKSRYF105Z10 R0374 RS1/16S6802F C0215, C0217, C0221, C0222, C0226 CKSRYF105Z10 R0257 RS1/4SA1R0J R0258, R0259, R1589, R1590 RS1/4SA2R2J DVD-V8000...
Page 79 VR8501 TURN TYPE VR DCS1090 S8701 SLIDE SWITCH DSH1064 X8801 CRYSTAL RES.(32.768MHz) BSS1115 RESISTORS CN8001, 8701 24P FFC CONNECTOR VKN1814 CN8702 D-SUB 15P CONNECTOR DKN1435 R7501 RS1/10S75R0F R7502–7508 RS1/10S68R0D CN8703 9P D-SUB SOCKET AKP1213 R7512 RS1/10S1R0J Other Resistors RS1/16S###J DVD-V8000...
Page 80 JA9702 USB CONNECTOR DKN1417 KN9701 TERMINAL VNF1084 CN9701 12P PH CONNECTOR AKM1283 All Resistors RS1/16S###J CAPACITORS C9701–9704 CCSRCH470J50 C9705, 9706 CKSRYB105K6R3 C9711, 9712 CEAT101M16 KEYB ASSY SEMICONDUCTORS IC9001 RPM7240-H4 Q9001–9005,9011-9015 DTA124EK D9001–9004 SLI-343DCW (STU) D9005 SLR-343EBT (KLMN) D9011–9015,9021–9025 1SS355 DVD-V8000...
Page 81: Adjustment
27.000 MHz Clock Adjustment 6.2 JIGS AND MEASURING INSTRUMENTS Screwdriver Screwdriver Test mode remote control (medium) Screwdriver (large) (small) TV monitor unit (GGF1381) Frequency counter Display digit ≥ 8-digit Screw tight DVD test disc Precise screwdriver Soldering iron (GYL1001) (GGV1025) DVD-V8000...
Page 82: Necessary Adjustment Points
Electric point ∗ After adjustment, screw locks Mechanical Ÿ Exchange the Spindle Motor point with the Screw tight. Electric point Exchange PCB Assy Mechanical Exchange PC Board point LOAB and DVDM ASSYS Electric point Note: 1 is already adjusted. DVD-V8000...
Page 83: Test Mode
Perform only trace, video and audio outputs are nothing. < When playback with the target address of disc (DVD)> For example, when playback with # 30000 During PLAY CHP/TIM Press keys in order 030000 TEST MODE: OFF POWER GGF1381 Test mode remote control STANDBY unit DVD-V8000...
Page 84: Mechanism Adjustment
(Refer to "6.1 ADJUSTMENT ITEMS AND LOCATION".) Spacer for Height adjustment Note: Turn a flat side Before removing the flexible cable for the into bottom pickup, soldering of the pickup circuit is necessary. For details, see "7.6 DISASSEMBLY". DVD-V8000...
Page 85: Dvd Jitter Adjustment
• The measurement of block error rate tangential and radial adjustment screws with the Screw tight. Screw tight: GYL1001 Test mode end • Reset Playback time B, referring to "7.1.7 Accumulated Power-on Time and Playback Time." DVD-V8000...
Page 86: Electrical Adjustment
27.000 MHz Clock Adjustment • If adjustments are inappropriate, color dislocation occurs. DVDM ASSY • Normal mode • Power ON 27.000 MHz ± 130 Hz or less VR 1 Player START DVDM ASSY Frequency counter 27 MHz TEST POINT DVD-V8000...
Page 87: General Information
Replace the Traverse Mechanism Assy or Pickup. Note : When a DVD disc or a CD disc is played in the test mode, this function is effective. Character in bold : Item name : Information display Laser diode current value Test mode screen DVD-V8000...
Page 88: Test Mode Specifications
2 C1 error value of DVD [ER – ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ] The type of discs loaded is displayed. _ Internal operation mode of mechanism controller Unknown : [NON] [MM – ∗ ∗ : ∗ ∗] : [DVD] : [ CD] Internal mechanism mode (2 digits) and internal mechanism DVD-V8000...
Page 89 - Screen display ON/OFF 1. Turn off the display by pressing the [A. MON] (A8-1E) key of the Test mode remote control unit. 2. Turn on the display by pressing the [DISPLAY] (A8-43) key of the Test mode remote control unit. DVD-V8000...
Page 90: Self-Diagnosis Function
In a case of an error for Item 3 VIDEO ENCODER NG VIDEO ENCODER NG PROU In a case of an error for Item 4 F.E REGISTER ACCESS NG In a case of an error for Item 5 F.E SDRAM ACCESS NG DVD-V8000...
Page 91 : Result of Item 3 (OK/FE-AV1 DMA NG) F.E. : Result of Item 4 (OK/NG ADV, >ADV, >PRO) : Result of Item 5 (OK/NG) TREX : Result of Item 6 (OK/NG) : Result of Item 7 (OK/NG) PROM : Result of Item 8 (OK/NG) DVD-V8000...
Page 92: Functional Specification Of The Service Mode
" * " of last one digit shows the EDC Check NG Count Over. " # " shows the ID Check NG Count Over. When " * " and " # " are not indicated, show that data were rightly readable by retry process. DVD-V8000...
Page 93: Error Display
Were not able to playback from the disc distinction process. 38 Disc-type- PLAY or STOP was not completed by backup operation of the disc distinction. Open sensing error Distinguished it from the blank disc in the ATB process completion. DVD-V8000...
Page 94 Subcode check No frame could be read for 3 failure during Stop seconds or more. playback ID can not read An ID could not be read within 1 second after the AFB Open during startup tracking on. (ID readout failure) DVD-V8000...
Page 95 Operation of the Unit AV1 access error bit3=1 08 etc. (read, write NG) No operation or it becomes debugging indication if the power is able to ON. bit2=1 04 etc. EBY-CHIP access error bit0=1 01 etc. SRAM access error DVD-V8000...
Page 96: Error History
As the maximum number of errors that can be displayed on one page is 8, if the number of errors is 9 or more, switch between Page 1 (No. 1-8 logs) and Page 2 (No. 9-16 logs) by pressing the CHP/TIM key. DVD-V8000...
Page 97 2 Accumulated power-on and playback time when copying to a USB memory device is performed 3 Content that is indicated on the screen, i.e., error code, accumulated power-on time when the error is generated, and the number of times the error was generated Example: FAMP000009.txt DVD-V8000...
Page 98: Accumulated Power-On Time And Playback Time
The display becomes that for reset confirmation. (In the following example, only the playback time is to be reset.) Flashes. To execute resetting, press the SEARCH key again. To exit this mode without resetting, press the ESC key on the remote control unit for service. DVD-V8000...
Page 99: Trouble Shooting
DVDM Assy CN115-pin 12 (INSIDE SW signal) • Check the loading drive signal : IC351-pin 14, 15 and 16 • Check the +6V and +12V power supply voltage (If above voltage is not supplied, check the micro-fuse P202 and P301.) DVD-V8000...
Page 100 • Check digital data of video and audio signals (audio signals: 3 line data, video signals: 8 bit data) shown to each schematic diagram and an analog signal line. In addition, check CLK. Audio system: 22/24 MHz, Video system: 27 MHz Indicate the error message. Refer to the section "7.1.5 ERROR DISPLAY". DVD-V8000...
Page 101: Power On Sequence
: See "7.1.3 Self-diagnosis Function." displayed on the LCD. the communication : If the communication with the sub-microcomputer is not established, with the sub-microcomputer a reset signal is issued from the sub-microcomputer every 5 seconds. established? Acquiring data from the real-time clock DVD-V8000...
Page 102 LCD. detected? Is a disc Stop installed? The target that has been programmed is Timer start? searched for and playback will start. Power on start? Is there a Playback starts according to the navigation. First Play PGC? Stop DVD-V8000...
Page 103: Failure Judgment Of The Hdmi Transmitter Ic
Does the monitor support HDCP? Check if there is any problem with the initialization processes, including HDCP initialization. (Connect a Pioneer plasma Purpose: display that is equipped with the HDMI input for checking. To check if there is any problem with the HDMI output line The HDMI-DVI conversion cable is required for the connection.)
Page 104: Upgrading
3 The indications on the LCD change from ERASE, WRITE, to DL OK. Then the unit will be automatically reset and will restart. Display the SETUP menu and check that the version of the firmware is upgraded. If upgrading fails, for example, because a power failure occurred during downloading, downloading via the serial port, by connecting a PC is required. DVD-V8000...
Page 105: If Upgrading Of The Firmware Fails
In such a case, click on the Start button again. • If downloading fails after the third attempt, a cause other than a communication error is suspected. • It takes about 5 minutes to download the firmware. 5 The player will automatically restart after downloading is completed. DVD-V8000...
Page 106: Setting The Destination
Press the SEARCH key to determine the selected destination area, write the data to the EEPROM, and terminate Destination Setting mode. When Destination Setting mode is terminated, ID Setting mode is automatically entered if the CPRM ID is not set yet. Note: When the destination was set once, other destination cannot modify. DVD-V8000...
Page 107: Setting The Id Number And Copying The Id Data
("IN ID DATA" is displayed on the LCD.) Install the ID data disc in the disc tray and press the Close key on 8 After confirming the above indications, press the CLEAR the main unit. Data will be read from the disc. key to terminate Setting mode. DVD-V8000...
Page 108: Serial Number Setting
To exit Serial Number Setting mode without writing the set serial number to the EEPROM, press the CLEAR key. Note: As a serial number, from the first to the 4th and 11th to 12th digits from the left are reserved for uppercase alphabetics only, and from the 5th to 10th digits are reserved for numerics only. DVD-V8000...
Page 109: Disassembly
Insert a · screwdriver (small) into the slit, and slide the drive cam in the direction of the arrow. Pull the tray by a hand. Slit · Screwdriver (small) Drive cam Bottom view Bottom plate Tray Bottom view Bottom view DVD-V8000...
Page 110 Front Panel Section Disconnect the one flexible cable. Disconnect the two connectors. Remove the one screw. Unhook the five hooks. 1 2 2 CN1502 CN1504 CN1501 DVDM Assy Bottom view Remove the front panel section. Front panel section DVD-V8000...
Page 111 DVDM Assy Remove the one screw. Note: Be sure to use a Bit Size No. 1 Phillips screwdriver. Remove the two hex. screws. Rear view DVDM Assy Disconnect the one connector. Remove the five screws. Remove the DVDM Assy. CN1201 DVD-V8000...
Page 112 Hex. screw (inch) : 3 × 8 P tight (copper) : 3 × 6 B tight (black) : Note: Be sure to use a Bit Size No. 1 Phillips screwdriver. Note: Be sure to use a Bit Size No. 1 Phillips screwdriver. DVD-V8000...
Page 113 Mecha. case (top) Short-circuit two points of C and D by soldering. Rear view Note: After replacement, connect the flexible cable, then remove the soldered joint (open). Remove the one screw. Remove the mecha. case (side). Mecha. case (side) DVD-V8000...
Page 114 Disconnect the three flexible cables, and the one connector. CN103 CN115 CN114 CN111 DVDM Assy Remove the four screws. Remove the LOADER MECHA. Assy. LOADER MECHA. Assy DVD-V8000...
Page 115 Loading base Triangle Cleanning Pickup lens Before shipment, be sure to clean the pickup lens, using the following cleaning materials: Cleaning liquid : GEM1004 Cleaning paper : GED-008 DVD-V8000...
Page 116 Front side placement. Flexible cable Flexible cable Bottom view for the pickup for the stepping motor Cleaning paper GED-008 Cleaning liquid GEM1004 Remove the four hooks. Traverse Mecha. Assy-S × 2 Remove the Traverse Mecha. Assy-S. × 2 DVD-V8000...
Page 117 Remove the flexible cable for the pickup. Flexible cable for the pickup Bottom view Adjustment screw Adjustment screw Remove the two adjustment screws and two adjustment springs. (Skew screw) (Skew screw) Remove the Pickup Assy-S. Pickup Assy-S Adjustment spring (Skew spring) Adjustment spring (Skew spring) DVD-V8000...
Page 118 Joint spring Silicone adhesive GEM1037 Joint 03 Silicone adhesive GEM1037 Arrangement of the flexible cable Arrangement of the flexible cable for the spindle motor for the stepping motor : Conductive surface : Conductive surface Hook Hook Bottom view Bottom view DVD-V8000...
Page 119 Make sure there is no slack in the cable Reference line Hook Fold the flexible cable as indicated in the photo. Hook the part folded in Step 1 to the hook. Reference Pass the cable below the hook line Hook DVD-V8000...
Page 120: Pin Function Of The Pcb Assy
V+12 +12 V • The status of audio-switch port Pin Name Low (0V) Hi (+3.3V) ASEL Audio_out outputs DVD Audio signal Audio-out outputs Ext_In Audio signal. XAMUTE Audio-out is not output. (mute on) Audio-out can be output. (mute off) DVD-V8000...
Page 121 (7) CN9501 (CKS2977): PWSB Assy → CN9002 (CKS2977): KEYB Assy No. I/O Pin Name Pin Function No. I/O Pin Name Pin Function − GNDD POWER_LED L (0 V): Standby LED, H (3.3 V): Power ON LED POWER_SW Power SW signal V+5E EVER +5 V DVD-V8000...
Page 122: External Connection
− GNDA GNDA (8) JA8505 (VKX1013): AJKB Assy → Digital Audio input products No. I/O Pin Name Pin Function No. I/O Pin Name Pin Function − D-OUT Optical Digital Audio output (Optical) GNDD D-OUT Coaxial Digital Audio output (Coaxial) DVD-V8000...
Page 123 D- signal for USB port 2 I/O D+ (U) D+ signal for USB port 1 I/O D+ (D) D+ signal for USB port 2 − − GND (U) GNDD for USB port 1 GND (D) GNDD for USB port 2 DVD-V8000...
Page 124 KeyIN1-4 KeyOUT1-5 LED CSYN C SW +3.3 DP1,2 LCD VR MP1, 2 Uses • Servo system control • System control • MPEG data decode • Analog video output and Digial audio output • DVI output control • USB signal control DVD-V8000...
Page 125 (4) CN114 (VKN1409) For carriage motor No. Pin Name Pin Function No. Pin Name Pin Function − − ST1- Motor control 1 (-) ST2+ Motor control 2 (+) − − ST1+ Motor control 1 (+) ST2- Motor control 2 (-) DVD-V8000...
Page 126 Pin Function I/O LCD data bus I/O LCD data bus I/O LCD data bus I/O LCD data bus I/O LCD data bus I/O LCD data bus − I/O LCD data bus Backlight anode − I/O LCD data bus Backlight cathode DVD-V8000...
Page 127 SEL_M_LED Monitor select LED output KEY_OUT4 Key matrix output 4 KEY_IN2 Key matrix input 2 − Ground SEL_V_LED Video select LED output KEY_OUT3 Key matrix output 3 KEY_IN1 Key matrix input 1 − Ground SEL_A_LED Audio select LED output DVD-V8000...
Page 128 TCLK- TMDS clock - − Td1+ TMDS data 1+ Not used − − Td1/3Shield Ground Not used − − Not used Not used − − Not used Not used − − +5 V power supply Not used − Ground DVD-V8000...
Page 129 H (5 V)_In squeeze mode Inhibit ¶ Disc type switch Disc Type ¶ LCD mode switch Control Mode Selection SEL_TV 1.25 V NTSC Data input AUTO Instruction code input ¶ LCD read/write Read/write Switch Read mode R/XW Write mode DVD-V8000...
Page 130: Parts
TE balance adjustment Connection terminal of a resistor and a capacitor for charge pump gain setting Capacitor connection terminal for tracking hold Focus error output Tracking error output Resistor connection terminal for push-pull gain setting Push-pull output Tracking cross signal output DVD-V8000...
Page 131 Capacitor connection terminal for RF DC servo DEFC Capacitor connection terminal for deffect detection − Ground (for RF) RF output Reference output EQC1 Equalizer setting terminal for CD − Power supply (RF system) EQC2 Equalizer setting terminal for CD DVD-V8000...
Page 132 Address bus Address bus Address bus Address bus Address bus For Wobble detection corresponding to DVD R/W (main) − Ground − V3R3 Power supply (+ 3.3 V) STEP1 D/A For stepping motor control STEP2 D/A For stepping motor control DVD-V8000...
Page 133 USB Power supply control signal V_SEL1 MONITOR output switch V_SEL2 VIDEO output switch SDA1 I/O I2C control lines − SDA0 Not used SCL1 I/O I2C control lines − SCL0 Not used CTS_3V RS-232C clear to send input RS-232C data terminal ready output DVD-V8000...
Page 134 DMA request input from the AV-1 CHIP 144 XDACK1 DMA response output to the AV-1 CHIP − 145 EN_FLOW Not used 146 DDC_ON Communication enable signal of the HDMI CONT − 147 XDFCS3 Not used − 148 GND Ground DVD-V8000...
Page 135 170 DFRST0 DAC reset (for front L/R) 171 DFRST1 Not used 172 XCSDF0 DAC (front) chip select or latch − 173 P94 Not used − 174 P95 Not used − 175 P96 Not used − 176 TM_ENT Not used DVD-V8000...
Page 136 DD12 I/O Data bus 12 for DRAM DD11 I/O Data bus 11 for DRAM DD10 I/O Data bus 10 for DRAM I/O Data bus 9 for DRAM I/O Data bus 8 for DRAM I/O Data bus 7 for DRAM DVD-V8000...
Page 137 XSDREQ DMA request output XSWAIT Wait signal output XSCL1 Chip select input XSRD Read signal input XSWR Write signal input SAD7 Data bus D15 100 SAD6 Data bus D14 101 SAD5 Data bus D13 102 SAD4 Data bus D12 DVD-V8000...
Page 138 Pulse output of duty 50 % 152 AFC Output frequency error of VCOCLK and reference clock as a PWD pulse 153 APC Output a PLL phase error as a PWD pulse − 154 VDD3.3 Power supply (+ 3.3 V) − 155 GND Ground DVD-V8000...
Page 139 202 ASDATA4 Not used − 203 ASDATA3 Not used − 204 ASDATA2 Not used − 205 ASDATA1 Not used − 206 ASDATA0 Not used − 207 VDD3.3 Power supply (+ 3.3 V) − 208 VDD2.5 Power supply (+ 2.5 V) DVD-V8000...
Page 140 Power supply (+ 1.8 V) − VDD33 Power supply (+ 3.3 V) XWRH Control signal (write upper) XWRL Control signal (write lower) XWAIT TO Read/write completion of data Acknowledge signal input XINT0 Interruption request 0 XINT1 Interruption request 1 XINT2 Interruption request 2 DVD-V8000...
Page 141 − Ground Data bus 2 for SDRAM MD13 Data bus 13 for SDRAM Data bus 1 for SDRAM 100 MD14 Data bus 14 for SDRAM 101 MD0 Data bus 0 for SDRAM 102 MD15 Data bus 15 for SDRAM DVD-V8000...
Page 142 Not Used − 149 NCO Not Used − 150 NCO Not Used − 151 NCO Not Used − 152 NCO Not Used − 153 NCO Not Used − 154 NCO Not Used − 155 VDD18 Power supply (+ 1.8 V) DVD-V8000...
Page 143 Bit stream data input 2 204 BD3 Bit stream data input 3 205 BD4 Bit stream data input 4 206 BD5 Bit stream data input 5 207 BD6 Bit stream data input 6 208 BD7 Bit stream data input 7 DVD-V8000...
Page 144 VDD for Core (+ 2.5 V) − Digital ground Through data input Through data input Horizontal sync. signal input Vertical sync. signal input − VDDE VDD for I/O (+ 3.3 V) Field identification signal input ALSB I2C slave address setting pin DVD-V8000...
Page 145 Video data R output − Digital ground − OVDDE2 VDD for I/O (+ 3.3 V) Video data R output Video data R output Video data R output Vertical sync. signal output Horizontal sync. signal output Data enable signal output DVD-V8000...
Page 146 Built-in PLL/external PLL selection − 116 OVDDE4 VDD for I/O (+ 3.3 V) 117 DCLK 27 MHz clock input − 118 OVSS1 Digital ground 119 DCLKP DCLK polarity setting pin − 120 VDDI VDD for Core (+ 2.5 V) DVD-V8000...
Page 147 Test input (connect to ground) CLKO 27 MHz clock output ANSI/SMPTE293M output (Y) ANSI/SMPTE293M output (Y) ANSI/SMPTE293M output (Y) ANSI/SMPTE293M output (Y) ANSI/SMPTE293M output (Y) − OVDD VDD for I/O (+ 3.3 V) − OVSS Digital ground for I/O ANSI/SMPTE293M output (Y) DVD-V8000...
Page 148 Digital ground for I/O − CVSS Digital ground for core − OVDD VDD for I/O (+ 3.3 V) MA10 SDRAM address output SDRAM address output MA11 SDRAM address output SDRAM address output − OVDD VDD for I/O (+ 3.3 V) DVD-V8000...
Page 149 VDD for I/O (+ 3.3 V) − 140 PLL_VDD VDD for PLL (+ 2.5 V) 141 VPDX Connect to ground 142 TEST6 Test input (connect to ground) − 143 PLL_GND Ground for PLL − 144 IVDD VDD for I/O (+ 3.3 V) DVD-V8000...
Page 150 12 bit input pixel data bus 12 bit input pixel data bus 12 bit input pixel data bus − Digital VCC (+ 3.3 V) − Digital ground 12 bit input pixel data bus 12 bit input pixel data bus DVD-V8000...
Page 151 12 bit input pixel data bus 12 bit input pixel data bus 12 bit input pixel data bus 12 bit input pixel data bus 12 bit input pixel data bus 12 bit input pixel data bus − Digital ground DVD-V8000...
Page 152 I/O Port data for USB I/O I/O Port data for USB I/O I/O Port data for USB I/O I/O Port data for USB I/O I/O Port data for USB I/O TEST4 I/O Not used I/O Data bus I/O Data bus DVD-V8000...
Page 153 I/O Data bus I/O Data bus I/O Data bus XRESET Master reset Memory write strobe Memory read strobe TMS0 Not used TMS1 Not used TMS2 Not used TMS3 Not used XINT Interrupt Address/ data select − Ground − Ground DVD-V8000...
Page 154 PWR_KEY Power on key input XLCDON LCD backlight lighting signal − Not used − Not used − Not used − Not used − Not used − Not used − Not used HXRST System reset signal P_CON Power control signal DVD-V8000...
Page 155 − Not used − Not used − VDD0 Power supply (+ 3.3 V) − AVREF0 A/D reference voltage input KEY_IN1 Key matrix input KEY_IN2 Key matrix input KEY_IN3 Key matrix input KEY_IN4 Key matrix input KEY_OUT1 Key matrix output DVD-V8000...
Page 156 Ground of A/D and D/A for servo AUXO D/A auxiliary output TILTDO Tilt control output TBAL Tracking balance control signal output − SLDO Not used − SPDO Not used Focus control signal output Tracking control signal output − VREF D/A reference level for servo DVD-V8000...
Page 157 Jitter output of PLL clock for EFM playback − Not used LCHP Address input LCHN Sync concordance pulse input of DVD RCHP Sync signal input of DVD − RCHN Not used − DVDD2 Power supply (+ 3.3 V) − DVSS Ground − 100 LEFM Not used DVD-V8000...
Page 158: Lcd Module
H, H → L Chip enable signal Data bit 0 Data bit 1 Data bit 2 Data bit 3 Data bit 4 Data bit 5 Data bit 6 Data bit 7 LED+ 4.2V Back light anode LED- Back light cathode DVD-V8000...
Page 159: Disc / Content Format Playback Compatibility
“DualDisc” media is supported, but DVD-audio media can- finalized. not be played. Refer to the manufacturer or your dealer for more informa- is a trademark of DVD Format/Logo Licensing Corpora- tion on the specifications and standards of “DualDisc” me- tion. dia. DVD-V8000...
Page 160: Panel Facilities
When the button is pressed so that the indicator lights, video 24 RETURN button signals input to the VIDEO IN connectors are output at MONI- Press to return to previous menu screens when in screens TOR VIDEO OUT. such as SETUP menu screen or menu screen. DVD-V8000...
Page 161: Rear Panel
Important 2 Extend Terminal connector (EXT TERMINAL) • The DVD-V8000 is provided with video and audio input External switches can be connected to control the DVD-V8000. connectors, and supports the use of 1 Vp-p composite The connector can also be used as an RS-232C interface.
Page 162: Remote Control Unit
Press during slow-mo- Press to open the SETUP menu. tion playback to change playback speed. Press and hold for one second to open the ADV. SETUP menu. Press again to close the SETUP or ADV. SETUP menu. DVD-V8000...
Page 163: Loading Batteries In The Remote Control Unit
Press to display the Play Mode menu. Using the scroll wheel during image playback 31 ANGLE button ( The DVD-V8000 supports the use of the mouse’s scroll wheel Press to change the camera angle during DVD multi-angle to perform operations during video playback.
Page 164: Rack Mount Kit (Cb-A802)
9. RACK MOUNT KIT (CB-A802) 9.1 PACKING SECTION DVD-V8000...
Page 165 Master Carton RM (Paper) DHG2656 Mirror Mat Sheet (300 * 330) DHL1161 Vinyl Bag Z21-013 Poly Bag DHL1162 NSP 9 Master Spacer (Paper) DHA1724 Recycle Label M DRW2307 NSP 11 Top Pad (Paper) DHA1725 NSP 12 Round Pad (Paper) DHA1727 DVD-V8000...
Page 166: Installation Procedures
Be sure to Dimensional Diagram confirm that all screws are tightened securely. elongate hole 6 x 10 (4places) 465.1 unit : mm 482.3 DVD-V8000...
Page 167 DVD-V8000...
Page 168: Jigs List
• Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Position to be cleaned Cleaning tools Cleaning tools Remark Remark Pickup leneses Cleaning liquid : GEM1004 Refer to "2.5 TRAVERSE MECHA ASSY-S" , "7.6 DISASSEMBLY". Cleaning paper : GED-008 DVD-V8000...

This manual is also suitable for:

Cb-a802xj Cb-a802wl5 Cb-a802

Pioneer DVD-V8000 Service Manual

1 Specifications

2 Exploded Views and Parts List

3 Block Diagram and Schematic Diagram

4 Pcb Connection Diagram

5 Pcb Parts List

6 Adjustment

7 General Information

8 Panel Facilities

9 Rack Mount Kit (Cb-A802)

Quick Links

DVD PLAYER

Related Manuals for Pioneer DVD-V8000

Summary of Contents for Pioneer DVD-V8000

This manual is also suitable for:

Table of Contents