1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Security System
  5. V4000
  6. Installation and setup manual

Honeywell V4000 Installation And Setup Manual

Remote video system
Hide thumbs Also See for V4000:
Table of Contents

Quick Links

K14020 6/05 Rev. A
R R R R
e e e e
m m m m
R R R R
e e e e
m m m m
Installation and Setup Guide
Installation and Setup Guide
Installation and Setup Guide
Installation and Setup Guide
V V V V
4 4 4 4
V V V V
4 4 4 4
o o o o
t t t t
e e e e
V V V V
i i i i
d d d d
e e e e
o o o o
S S S S
o o o o
t t t t
e e e e
V V V V
i i i i
d d d d
e e e e
o o o o
S S S S
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
y y y y
s s s s
t t t t
e e e e
m m m m
y y y y
s s s s
t t t t
e e e e
m m m m
Table of Contents
loading

Related Manuals for Honeywell V4000

Summary of Contents for Honeywell V4000

  • Page 1 V V V V 4 4 4 4 0 0 0 0 0 0 0 0 0 0 0 0 V V V V 4 4 4 4 0 0 0 0 0 0 0 0 0 0 0 0 R R R R e e e e m m m m...

  • Page 3: Table Of Contents

    Table of Contents Introduction .........................5 Basic Operation .......................5 Remote Look In .......................5 Features:...........................5 Specifications: .........................6 Installing the V4000 ......................7 Mounting .........................7 Wiring..........................7 Programming the Control Panel ..................9 Setup Considerations .......................9 Control Center Software Installation ...................9 Minimum System Requirements ..................9 Recommended System Requirements ................10 Software Installation......................10...

  • Page 5: Introduction

    V4000 via the control panel’s keypad (ECP) bus. The remaining video buffer memory is used to capture the event. When the remaining memory is filled, recording of video events ceases.

  • Page 6: Specifications

    Specifications: Voltage: 12 to 17VDC Current Draw: Standby: 370 mA Transmitting: 490 mA Max. ECP Bus: 45mA Operating Temperature Range: 32° to 131°F (0° - 50°C) Humidity: 25 to 80% Non Condensing Resolution: 128h x 100v NTSC or PAL 256h x 100v NTSC or PAL 256h x 200v NTSC or PAL 512h x 200v NTSC or PAL Color Resolution:...

  • Page 7: Installing The V4000

    (e.g., fax machines). 2. Connect the video cables from the CCTV cameras to the BNC connectors. The DIP switches on the V4000 are set for direct connection of CCTV Notes: cameras to the unit (down). If the CCTV cameras are connected in parallel...
  • Page 8 The DIP switches on the interface board are not used. 3. Ensure that the designated trigger zones on the control panel are installed 4. Connect the Keybus terminals of the V4000 module to the control panel’s keypad (ECP) bus using 22AWG (5mm), quad, twisted two-pair wire.

  • Page 9: Programming The Control Panel

    Programming the Control Panel Setup Considerations Cameras connected to the V4000 can be triggered by system events from a Honeywell Vista control panel. The cameras are turned on using Output (relay) Programming commands in the control panel, although no relay module is actually used. To accomplish this, do the following: Enable a 4204 Relay Module in the system’s Device Programming Mode as...

  • Page 10: Recommended System Requirements

    The Choose Destination Location window will appear. This screen will determine the directory in which Control Center Software is installed. Honeywell recommends installation in the default directory. After the destination folder has been chosen, click Next to continue. Repeat Step 8 for the location of the data files.

  • Page 11: Initial Control Center Operation

    Select Sensor (Zone) Tab • Select appropriate zones (1-6) and assign Cameras (1-4) as required • Set Functionality to Alarm Click Upload to Program the V4000 module. Note: Refer to the Control Center Software User Guide for detailed programming information.

  • Page 12: Troubleshooting

    • Check video signal using a monitor. The Transmitting Unit does not call the VAS: • Verify that the V4000 module is connected to the control panel Keybus . • Verify that the correct zones are mapped to the correct CCTV cameras.

  • Page 13: Appendix B: Pan, Tilt & Zoom

    • Connect Dome to TxDA Pin 1(-) and TxDB Pin 2(+) of the DB9 Connector that plugs into the male DB9 connector on the V4000 module. Dial up the V4000 module from Control Center Software installed on a PC Select Tuning icon > Unit Power on parameters > Modems.

  • Page 14: Fcc Compliance Statement

    FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
  • Page 15 Equipment Maintenance Facility If trouble is experienced with this equipment, for repair or warranty information, please contact the facility indicated below. If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect the equipment until the problem is solved. This equipment is of a type that is not intended to be repaired by the end user.

  • Page 16: Limited Warranty

    Limited Warranty or otherwise if the product(s) is altered or improperly repaired or serviced by anyone other than Honeywell factory service. Connection of any device(s) to a communicating bus of a Honeywell security system (e.g., keypad bus, polling loop) other than those manufactured or approved by Honeywell shall void this warranty.

Table of Contents