Related Manuals for ABB SROUT
Summary of Contents for ABB SROUT
- Page 1 SROUT Router Option Card for ® Star Coupler RER 111 Technical Reference Manual ABB Automation...
- Page 2 (empty)
-
Page 3: Table Of Contents
1MRS 750109-MUM Router Option Card for Lon® Star Coupler SROUT RER 111 Issued: 09.12.1997 Version: B2/24.2.2000 Checked: M.K. Technical Reference Manual Approved: T.S. We reserve the right to change data without prior notice. Contents: 1. Introduction ................4 2. Functions ...................7 2.1. -
Page 4: Introduction
SROUT Router Option Card for Lon® Star Coupler 1MRS 750109-MUM RER 111 Introduction ® The router option card is designed to be used within the LON Star Coupler RER 111. This device is not a "stand-alone" device. The router option card connects two different communication channels and forwards LonTalk™... - Page 5 Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 MicroSCADA Fibre-optic connection Router Option Card Fibre-optic connection Fibre-optic connections SUBNET 1 to bay level devices Fibre-optic connections to bay level devices SUBNET 2 srout_2 )LJ 6\VWHP VWUXFWXUH ZKHQ WKH ILEUHRSWLF LQWHUIDFH LV XVHG WR GLYLGH D ODUJH...
- Page 6 SROUT Router Option Card for Lon® Star Coupler 1MRS 750109-MUM RER 111 MicroSCADA Fibre-optic connection Router Option Card SFIB103 BB SFIB103 BB SFIB103 BB SFIB103 BB SFIB103 BB SFIB103 BB SFIB103 BB SFIB103 BB SFIB103 BB SROUT-C- Fibre-optic connection Fibre-optic connections to bay level devices...
-
Page 7: Functions
Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 Functions The router option card has one 9-pin D-type connector for the twisted pair interface and one fibre-optic transceiver pair. There are two transceiver modules available for the twisted pair interface, either of which may be connected to the router core module RTR-10 via jumpers. -
Page 8: Fibre-Optic Interface
SROUT Router Option Card for Lon® Star Coupler 1MRS 750109-MUM RER 111 A message received from the twisted pair interface is passed on to the open-collector bus on the mother board, through the RTR-10 core module. A message received from the open collector bus is sent to the twisted pair interface through the RTR-10 core module. -
Page 9: Mechanical And Electrical Design
Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 Mechanical and electrical design 3.1. Block diagram Net B Service Net A Twisted-pair Fibre-optic interface interface Configuration jumpers Continuous light control TP/XF 1250 Module Control TP/XF 78 Logic... -
Page 10: Interfaces
SROUT Router Option Card for Lon® Star Coupler 1MRS 750109-MUM RER 111 Interfaces 4.1. General The router option card has five separate interfaces: - a 64-pin E1 card connector for the connection to the mother board of the RER 111 unit... -
Page 11: Fibre Optic Interface
Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 4.3. Fibre-optic interface For more information regarding fibre-optic cables and the fibre-optic connection of option cards, refer to the RER 111 manual 1MRS750104-MUM, chapter 6.2. 4.4. Service switch The service switch is used to produce a service-pin message. -
Page 12: Installation, Configuration And Programming
FOC3 FOC3 FOC3 1MRS060023 1MRS060023 srout_8 SROUT Option Card )LJ ,QVWDOODWLRQ RI URXWHU RSWLRQ FDUG LQ WKH 5(5 XQLW 5.2. Configuration of router option card 5.2.1. Configuration instructions The router option card has 4 individual sets of jumpers. These are used to specify the transceiver type for router side A, the use of termination in the twisted pair network and the use of the fibre-optic transceiver pair. - Page 13 Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 The figure below shows the required jumper settings of jumper groups S1, S2, S3 and S4 for each transceiver mode and the corresponding transceiver ID. Router side A can be set to be a TP/XF-78 interface, i.e. 78 kb/s speed, a TP/XF- 1250 interface, i.e.
-
Page 14: Default Settings
SROUT Router Option Card for Lon® Star Coupler 1MRS 750109-MUM RER 111 Disconnected Connected srout_11 )LJ -XPSHU JURXS 6 IRU FRQQHFWLQJ WKH ILEUHRSWLF LQWHUIDFH WR URXWHU VLGH % 5.2.2. Default settings: Table 5.2.2-1 The default settings of the jumpers... -
Page 15: Programming The Router By Using The Lon Network Tool (Lnt)
Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 Once the router option card has been programmed, the fibre-optic mode can be configured for router side A, if required. To enable this, the communication parameters must be set from router side B. In the fibre-optic mode, the following... - Page 16 SROUT Router Option Card for Lon® Star Coupler 1MRS 750109-MUM RER 111 the same subnet, the message will not be passed on to subnet 2. But if node X in subnet 1 sends a message to node Z in subnet 2, the message will naturally be passed on to subnet 2).
- Page 17 Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 6LQJOHHQGHG comm_type: comm_pin_dir:'LUHFWPRGH ± VLQJOHHQGHG channel type: FXVWRP (behind the 6HOHFW &KDQQHO 7\SH button) comm_clock: (behind the %LW 5DWH button) (behind the %LW 5DWH button) input_clock: 3UHVV WKH 5RXWHU 2WKHU 6LGH EXWWRQ Remember, in this case the parameters mentioned above must be same on the both router sides.
-
Page 18: Technical Data
Communication speed 1.25 Mb/s Connection to mother board 64-pin E1 connector Power source From the mother board +8 VDC Power consumption SROUT-C-MM option card <1.4 W SROUT-C-BB option card <1.4 W Size E1 card 100 mm x 160 mm Front plate 116.4 mm x 19.8 mm... -
Page 19: Maintenance And Service
Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 Maintenance and service Self-diagnostics 7.1. 7.1.1. Fibre-optic receiver LED The receiver LED flashes when a message is being received from the fibre-optic channel. If the LED is continuously lit, the channel is heavily loaded or there is a malfunctioning device sending continuous light. -
Page 20: Ordering Information
SROUT Router Option Card for Lon® Star Coupler 1MRS 750109-MUM RER 111 Ordering information When ordering please state the following: 1. Quantity 2. Type of fibre-optic transceivers Type designation Router option card Type Designation Router option card with ST-type glass fibre-optic transceivers... -
Page 21: Appendix A
Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 Appendix A Default values of communication parameters and routing tables for the router option card, sides A and B. These default values are set during manufacturing and they are stored in EEPROM memory of the Neuron chip. - Page 22 SROUT Router Option Card for Lon® Star Coupler 1MRS 750109-MUM RER 111 Table 3: Configuration structure fields and values programmed for router option card side B (open collector bus) during manufacturing Field of a structure Value Offset / # of bits Remarks...
- Page 24 ABB Substation Automation Oy P.O. Box 699 FIN-65101 VAASA Finland Tel. +358 10 224 000 Fax. +358 10 224 1094 www.abb.fi...