Table of Contents
Quick Links
Table of Contents
Related Manuals for DeWalt DCT414-XE
Summary of Contents for DeWalt DCT414-XE
- Page 1 INSTRUCTION MANUAL DCT414-XE 10.8 V CORDLESS IR THERMOMETER...
-
Page 3: Definitions: Safety Guidelines
SAVE THESE INSTRUCTIONS Definitions: Safety Guidelines WORK AREA SAFETY The definitions below describe the level of severity for each a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. signal word. Please read the manual and pay attention to these b) Keep children and bystanders away while operating a power tool. -
Page 4: Electrical Safety
d) Maintain power tools. Check for misalignment or binding of moving parts, • Young children and the infirm. This appliance is not intended for use by young children or infirm persons without supervision. Young children should be breakage of parts and any other condition that may affect the power tool’s supervised to ensure that they do not play with this appliance. -
Page 5: Warning Labels
• Tool service must be performed only by qualified repair personnel. Service WARNING: LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER or maintenance performed by unqualified personnel may result in injury. To PRODUCT MAXIMUM OUTPUT POWER <1mW. locate your nearest D WALT service center call (AUS) 1800 654 155 or WARNING: ALWAYS wear approved protective safety equipment complying with (NZ) 0800 339258... -
Page 6: Important Safety Instructions For All Battery Chargers
• Before using charger, read all instructions and cautionary markings on charger, WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If battery pack, and product using battery pack. battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. -
Page 7: Charge Indicators
• Do not operate charger with damaged cord or plug. 2. Insert the battery pack (C) into the charger, as shown in Figure 1, making sure the pack is fully seated in charger. The red (charging) light will blink continuously •... -
Page 8: Important Charging Notes
before use. A battery pack may also slowly lose its charge if left in a charger that is WARNING: Shock hazard. Don’t allow any liquid to get inside charger. Electric not plugged into an appropriate AC source. shock may result. WEAK BATTERY PACKS: Chargers can also detect a weak battery pack. - Page 9 Alarm mode button: is used to select the type of alarm and to set the high (HAL) and low (LAL) temperature limits for the alarm. DCT414-XE Alarm 1 – temperature has reached the set limit, indicated by the red/blue LED Alarm 2 - temperature has reached the set limit, indicated by a beeper sound Alarm 3 –...
-
Page 10: Assembly And Adjustments
INTENDED USE FIG. 3 The IR Thermometer measures surface temperatures by measuring the amount of infrared emitted off the object. This type of measurement is a non-contact measurement of the surfaces temperature. This tool comes fully assembled. This tool has been designed with features that allow for quick and easy set-up. ASSEMBLY AND ADJUSTMENTS WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/installing... - Page 11 Installing and Removing the Battery Pack (Fig. 4) NOMINAL EMISSIVITY MANUAL NOTE: Make sure your battery pack is fully charged. MATERIAL VALUE MATERIAL VALUE To install the battery pack (C) into the tool handle, align the battery with the rails Default**** 0.95 Lead*...
-
Page 12: Maintenance
6. Push the ALM button. The LAL (low alarm) will now flash. Use the up and down • To extend battery life, release the IR Thermometer trigger when not taking arrows to select the low temperature limit. When the temperature has descended, temperature readings. -
Page 13: Specifications
ACCESSORIES NOTE: Three Year Warranty is not applicable to items deemed as consumables. Radial arm saws are covered by a one (1) year warranty only. D WALT Reserves the right to WARNING: Since accessories, other than those offered by D WALT, have not been review its warranty policy prior to launch of any new business development products. - Page 16 WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 • 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (NOV10) Part No. N081545 DCT414-XE Copyright © 2010 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip;...