To cancel pairing mode - While the headset is in pairing
mode, you can cancel the pairing process and turn off
the headset. Press and hold the Talk button for about 5
seconds. You will hear an “OFF” tone, the Amber LED will
flash several times and the headset will turn off. Release
the Talk button.
Tips:
* The headset, in normal operation, should maintain a
link with the mobile phone at all times once pairing has
been successful and a connection has been established
between the two devices.
* If you find that you cannot put the headset into pairing
mode then try temporarily switching off (or disabling
Bluetooth) the last phone used with the headset.
* If disconnection or a lost link occurs, it may be due to the
following reasons:
a) The range is over 33 feet between the headset and the
mobile phone.
b) The mobile phone disconnected the link to conserve
power or enable another function.
c) Either device has been switched off.
FITTING THE HEADSET ON YOUR EAR
The Headset is designed to fit comfortably in your ear. The
ear hook can be fixed into the headset from both sides,
allowing you to position on right or left ear. The ear hook
can be separated from the Headset by simply pulling the
base of the ear hook away from the main body of the
Headset. The ear hook can then be reinserted in the other
direction for positioning on the opposite ear. The ear hook
is flexible and can be bent to adjust the fit that is best for
the individual user. To replace the ear cap - Stretch the
rubber ear cap around the end of the speaker until secure.
To place the headset on your ear - Place the headset
speaker in your ear with the microphone angled towards
your mouth. The headset should fit snugly in your ear.
SWITCHING ON YOUR HEADSET
To turn on the headset - With the headset turned off, press
and hold the Talk button for several seconds until you
hear the “ON” tone (four ascending “beeps”) or until you
see the Blue LED start to flash. Release the Talk button.
The headset will turn on and enter standby mode, ready
to make and receive calls. After turning on the headset,
the headset will try to connect to the last used phone
automatically.
To turn off the headset - With the headset turned on, press
and hold the Talk button for about 5 seconds. You will hear
an “OFF” tone (four descending “beeps”) and the Amber
LED will flash quickly several times and the headset will
turn off. Release the Talk button.
MAKING CALLS
You can make calls from your mobile phone, or directly
from the headset using voice dialing and last number
redial commands (if these features are supported by your
mobile phone).
To make calls from your mobile phone - Dial the call from
your mobile phone. Dependent on your mobile phone
settings the call is automatically connected to your
headset.
To make calls using VOICE DIALING (if supported by your
mobile phone) - Click the Talk button on your headset. You
will hear a Voice Dial tone possibly followed by the voice-
dial prompt tone from your mobile phone. Speak the name
of the person you wish to call. The call is automatically
connected to your headset.
To make calls using LAST NUMBER REDIAL (if supported
by your mobile phone) - While in standby mode, press and
hold the Volume DOWN “-” or Volume UP “+” button for
about 2 seconds, and you will hear a “Last Number Redial”
tone (four ascending beeps); Release the Volume button,
the call is automatically connected to your mobile phone.
(You can also double-click the Talk button to activate this
feature)
RECEIVING CALLS
You must configure your mobile phone to answer calls
directly on your Bluetooth headset. Refer to the mobile
phone user guide for instructions on initiating this feature.
When you hear your headset ring, click the Talk button on
the headset. The call is automatically connected to your
headset.
Reject calls (if supported by your mobile phone) You can
also reject calls by pressing and holding the Talk button
for about 3 seconds. You will hear a beep in addition to the
incoming ringing when the call reject is about to occur.
ENDING CALLS
When you have finished your call, click the Talk button on
your headset or end the call on your phone. The call will be
disconnected.
TRANSFERRING CALLS (if supported by your mobile
phone)
You can transfer calls connected to your headset back
to your mobile phone, or from your mobile phone to your
headset.
To transfer calls from your headset to the phone double-
click the Talk button. To transfer from phone to headset
simply click the Talk button once.