Fujitsu ScanPartner 620C User Manual
  1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Scanner
  5. ScanPartner 620C
  6. User manual

Fujitsu ScanPartner 620C User Manual

Image scanner
Hide thumbs Also See for ScanPartner 620C:
Table of Contents

Quick Links

®
ScanPartner
620C
Image Scanner
User' s Manual
(Doc. No. 250-0062-0 Ver. 1.0)
Table of Contents
loading

Related Manuals for Fujitsu ScanPartner 620C

Summary of Contents for Fujitsu ScanPartner 620C

  • Page 1 ® ScanPartner 620C Image Scanner User’ s Manual (Doc. No. 250-0062-0 Ver. 1.0)
  • Page 2 FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

  • Page 3: Table Of Contents

    3.1 CLEANING THE ADF....................3-1 3.2 CLEANING THE GLASS....................3-3 3.3 REPLACING THE ADF SNAP-IN PAD MODULE ............3-4 4. TROUBLESHOOTING .................. 4-1 4.1 QUESTION AND ANSWER ..................4-1 4.2 PAPER JAM IN THE ADF .....................4-3 5. SPECIFICATIONS..................5-1 5.1 SCANPARTNER 620C SPECIFICATIONS..............5-2 INDEX...

  • Page 4: Introduction

    INTRODUCTION Congratulations on your purchase of a Fujitsu ScanPartner 620C scanner. Before you install and operate the new scanner, please take a few minutes to read through this manual. It provides you with the proper instructions on how to unpack, install, operate and maintain the Scanner.

  • Page 5: Installation

    INSTALLATION Please unpack the scanner carefully, and check the contents against the checklist. If any items are missing or damaged, please contact your authorized local dealer immediately. Precautions • Keep the scanner out of direct sunlight. Direct exposure to the sun or excessive heat may cause damage to the unit.
  • Page 6 “ Shipping Position” “ Shipping Position” Figure 2-1 Removing the Shipping Bracket...
  • Page 7 “ Use Position” Figure 2-2 Securing the Shipping Bracket...

  • Page 8: Refitting The Shipping Bracket

    2.1.2 REFITTING THE SHIPPING BRACKET Whenever you need to move the scanner to a new location, it is advisable to refit the shipping bracket to avoid causing damage to the scanners’ internal mechanism. Please follow the instructions below to refit the shipping bracket. i).
  • Page 9 SCSI ID Selector SCSI Termination Switch Figure 2-3 Adjusting the SCSI ID setting...

  • Page 10: Adf Paper Chute

    2.3 ADF PAPER CHUTE Raise the right side of the ADF Paper Chute to about 45 degrees. ii). Pull down the wire leg from beneath the ADF Paper Chute. iii). Insert the wire leg into the grips on the Document Cover. iv).

  • Page 11: Adf Output Tray

    2.4 ADF OUTPUT TRAY Hold the output paper tray some 30 degrees aslant as shown in Figure 2-5. ii). Insert the three protrusions on the ADF Output Tray into the three slots on the ADF. iii). Release the paper tray gently. Make sure the tray is firmly attached to the ADF. iv).

  • Page 12: Document Loading

    2.5 DOCUMENT LOADING For flatbed scanning Documents that cannot be scanned using the ADF can be placed on the flatbed for scanning. (See Figure 2-6) Place the document to be scanned onto the document glass face down. ii). Position the document so that the upper-right corner is aligned with the Reference Mark. Document Cover Reference Mark Original Document...

  • Page 13: Adf Scanning

    2.6 ADF SCANNING Standard paper size can be scanned automatically using the ADF. Refer to Figure 2-7. To prevent occasional paper jams when automatically feeding multiple documents, fan the paper before loading. ii). Lift the Balance Wire and place the documents to be scanned onto the ADF Paper Chute face down, with the leading edge in the Auto Feeder entrance.

  • Page 14: Connecting The Cable

    SCSI Termination The Fujitsu ScanPartner 620C comes complete with a built-in SCSI terminator. If the Scanner is the last device in a SCSI chain, the Terminator should be switched ON. If the scanner is not the last device, the Terminator should be OFF. The Terminator ON/OFF switch is located on the back of the scanner, to the left of the SCSI cable connectors.
  • Page 15 Power Switch SCSI Port Power Cable Figure 2-8 ScanPartner 620C Power Cable Connection SCSI Cable Connector To PC SCSI Port Figure 2-9 ScanPartner 620C SCSI Cable Connection 2-11...

  • Page 16: Maintenance

    Cleaning Procedures (Figure 3-1) Moisten a cotton swab with isopropyl alcohol (95%). (Cleaner kits are available from Fujitsu.) Open the ADF unit by depressing the button • in front of the ADF unit. Carefully open the ii).
  • Page 17 ADF Pad Module Feeding Roller ¬ Figure 3-1 Opening the ADF unit and Document Cover...

  • Page 18: Cleaning The Glass

    3.2 CLEANING THE GLASS The procedures: Soak a cotton swab with some isopropyl alcohol (95%). ii). Open the ADF unit and document cover as shown in Figure 6-2. Wipe the glass in the flatbed area and ADF area by moving the swab from side to side. iii).

  • Page 19: Replacing The Adf Snap-In Pad Module

    REPLACING THE ADF SNAP-IN PAD MODULE After scanning approximately 150,000 pages through the ADF, the pad spring may become worn out and you may experience problems with document feeding. In this case, it is highly recommended to replace the pad module with a new one. To order the pad module, please consult your nearest dealer and follow the procedure below to replace it.
  • Page 20 Assembling Procedure Take out the ADF pad module from the box. Hold the upper part of the pad clamp and place it gently into the pad holder as shown in Figure 3-4. Upper Part of the Pad Clamp ADF Pad Module Figure 3-4 Installing the pad module...

  • Page 21: Troubleshooting

    Check if the driver is correctly installed. You can use the DIAG.EXE file in the “ Fujitsu Driver Kit” to check this out. c) Try to select another port memory. Question: Paper jams during scanning.
  • Page 22 Question: Paper skews in the scanner. Answer: a) Check the feeding roller condition; do the cleaning if necessary. (See Section 3.1) b) Use the paper guide when feeding the paper. Question: When the scanner is powered-on, it makes noises and will not stand ready. Answer: a) Check to make sure the shipping retainer from the scanner is removed.

  • Page 23: Paper Jam In The Adf

    Question: While scanning, the scanner often makes noises, or it scans back and forth. Answer: Choose a lower speed from the TWAIN user interface for a low speed PC. Question: The scanned image is too dark. Answer: a) Use your application to modify the Gamma setting to 2.2 and 1.8 for your printer and monitor respectively.
  • Page 24 ADF Unit ADF Paper Chute Document Figure 4-2 ADF Paper Jam - Removing the Paper...

  • Page 25: Specifications

    SPECIFICATIONS All specifications are subject to change without notice. The following can not be properly fed into the ADF: • Paper with clips or staples attached; • Paper with ink not totally dry; • Paper with inconsistent thickness, such as envelopes; •...

  • Page 26: Scanpartner 620C Specifications

    5.1 SCANPARTNER 620C SPECIFICATIONS v 1-pass colour Scanner Type v Flatbed with ADF built-in v 36-bit colour Scanning Mode v 12-bit Grey Scale v Line Art/Halftone v Error Diffusion (single bit) v 600 x 1200 dpi in a dpi increments...

  • Page 27: Index

    Index ADF cover · 4-3 paper chute · 2-5 ADF Scanning · 2-8 paper chute extension · 2-5 paper jam · 2-8, 4-3 POWER LED · 2-9 protrusions · 2-6 balance wire · 2-8 READY LED · 4-1 Cleaning the ADF · 3-1 reference mark ·...
  • Page 28 © 1999 Fujitsu Computer Products of America, Inc. All rights reserved. The statements contained herein are not intended to create any warranty expressed or implied. Fujitsu Computer Products of America reserves the right to change equipment and performance specifications stated herein without notice.

Table of Contents