Tv/weather/fm/am cd kitchen clock radio (50 pages)
Summary of Contents for Sony ICF-CD2000
Page 1
US Model Canadian Model Ver 1.0 1999. 10 E Model Tourist Model ICF-CD2000 AEP Model UK Model ICF-CD2000S Photo: ICF-CD2000 (US model) Model Name Using Similar Mechanism D-E551 Optical Device Name CDM-2911EBA Optical Pick-Up Name DAX-11E SPECIFICATIONS ICF-CD2000 FM/AM CD CLOCK RADIO...
OPERATION. REPLACE THESE COMPONENTS WITH DE FONCTIONNEMENT. NE REMPLACER CES COM- SONY PARTS WHOSE PART NUMBERS APPEAR AS POSANTS QUE PAR DES PIÈCES SONY DONT LES SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- NUMÉROS SONT DONNÉS DANS CE MANUEL OU LISHED BY SONY.
SECTION 1 SERVICING NOTES Precautions for Checking Emission of Laser Diode NOTES ON HANDLING THE OPTICAL PICK-UP Laser light of the equipment is focused by the object lens in the BLOCK OR BASE UNIT optical pick-up so that the light focuses on the reflection surface of the disc.
Page 4
• Method-2 (In the service mode or normal operation): Check the value of current flowing in the laser diode. 1. Remove the upper panel. 2. Connect a digital voltmeter as show in Fig. 2. 3. Press the key. 4. Calculate current value by the reading of the digital voltmeter. Reading of the digital voltmeter (V) ÷...
SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. Cabinet (lower) assy Cabinet (upper) Cabinet (front) sub assy Optical pick-up Main board (CDM-2911EBA) Note: Follow the disassembly procedure in the numerical order given. CABINET (LOWER) ASSY 5 cabinet (upper) assy 4 flat wire (CN301) 1 Open the battery case lid.
Page 9
CABINET (UPPER) 1 screw (2 × 8) 2 two claws 2 four claws 1 screw (2 × 8) 3 cabinet (upper) 2 three claws CABINET (FRONT) SUB ASSY 6 cabinet (front) sub assy knob (open) 2 Slide the knob (open) in the direction of the arrow A , and open the cabinet front assy.
Page 10
OPTICAL PICK-UP (CDM-2911EBA) 3 optical pick-up (CDM-2911EBA) 2 three connectors (CN601, 602, 603) 1 connector (CN501) MAIN BOARD 3 two screws (B1.7 × 5) 4 Remove two solders. 5 jack board 6 screw (2 × 8) 2 telescopic antenna 7 main board 1 screw (B3 ×...
SECTION 4 SERVICE MODE Service Mode (Service program) The equipment is provided with a service program built in the microcomputer, like conventional models. Service program operation methods are described in the follow- ing. • Step 1 (Service mode setting methods) 1.
SECTION 5 TEST MODE [Test Mode 1] [Test Mode 3] • Step1 (Test mode 1 setting methods) • Step1 (Test mode 3 setting methods) 1. Connect TP445 (CD TEST 1) to the TP444 (GND). 1. Connect TP448 (CD TEST 3) to the TP449 (GND). 2.
Page 13
[ALARM TIME] [LCD Display Check Mode] • Step1 (LCD display check mode setting metyods) 1. Connect TP446 (TUNER TEST) to the TP444 (GND). 2. Insert external power supply. • Step2 (Operation in the LCD display check mode) 1. All segments of LCD light up if the LCD display check mode is activated.
Page 14
[PRESET 3] [PRESET 4] [PRESET 5] [ OFF, ALARM RESET] : All lit • Step3 (Resetting of LCD display check mode) 1. Remove external power supply. 2. Disconnect TP446 (TUNER TEST) and TP444 (GND). Connecting Location: – LCD Board (Conductor Side) – TP445 (CD TEST 1) TP448...
SECTION 6 ELECTRICAL ADJUSTMENTS AM (MW) FREQUENCY COVERAGE ADJUSTMENT TUNER SECTION 0 dB=1 µV Adjustment Part Frequency Display Reading on Digital Voltmeter [AM (MW)] 530 (531) kHz 1.7 V Setting: Confirmation 1,710 (1,602) kHz 8.5 V (9.0 V) Band switch : AM (MW) no mark: US, CND ( ) : AEP, UK, E, SP, JE Put the lead-wire AM (MW) TRACKING ADJUSTMENT...
Page 16
FM VCO Adjustment FM AUTO SCAN Adjustment Setting: Setting: FM RF SSG FM RF SSG 0.01 µ F 0.01 µ F MAIN board MAIN board FM/SW Telescopic FM/SW Telescopic Antenna (ANT1) Antenna (ANT1) Carrier frequency: 98 MHz Carrier frequency: 98 MHz Modulation: no modulation Modulation: no modulation Output level: 0.1 V (100 dB)
Page 18
Tracking Balance Check CD SECTION Condition: • Hold the set in horizontal state. Precautions for Adjustment 1. Before beginning adjustment, set the equipment to service Check Procedure: mode. After the completion of adjustment, be sure to reset the ser- oscilloscope (DC range) vice mode.
Setting terminal for the model Not used oscilloscope SHOCK (AC range) “L”: shock detection danger Setting terminal for the model “L”: ICF-CD2000, “H”: ICF-CD2000S MAIN board PAUSE Pause signal output to the LC78626KE (IC502) “H”: pause Setting terminal for the model “H”: E, Singapore, Tourist model D-RAM writing enable signal output to the LC78626KE (IC502) “H”: writing enable...
ICF-CD2000/CD2000S 7-2. BLOCK DIAGRAM – CD Section – • SIGNAL PATH EFMO : CD PLAY DETECTOR FIN2 EFMI LCHO FIN1 L-CH RF– SWITCH 1BIT (Page 27) Q504 LEVEL L. P. F. CONTROL RCHO R-CH DEFI (Page 27) FSTA CONT3/SBCK SUB CODE...
ICF-CD2000/CD2000S 7-3. BLOCK DIAGRAM – MAIN Section – (Page 26) (Page 26) ANT1 FM / AM FRONT-END FM / AM FRONT-END FM/SW TELESCOPIC ANTENNA IF DISCRI, IF AMP IF DISCRI, IF AMP (CD2000) MIX AMP LOW-PASS FILTER AMP IC1 (1/2)
ICF-CD2000/CD2000S 7-6. PRINTED WIRING BOARDS – LCD/KEY Boards – Note on Printed Wiring Boards: • Semiconductor Location • X : parts extracted from the component side. KEY BOARD (COMPONENT SIDE) KEY BOARD (CONDUCTOR SIDE) • Y : parts extracted from the conductor side.
ICF-CD2000/CD2000S 6-7. SCHEMATIC DIAGRAM – LCD/KEY Boards – • See page 42 for Waveforms. Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.
Page 27
IC502 LC78626KE 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 DATA WIDTH CONVERSION DEFI OVERFLOW PROCESS SHOCK SHOCK STARTING DETECTION EMPN CONTROL CLOCK VVSS OSCILLATION PAUSEIN ISET DRAM CONTROL VVDD CLOCK CNTOK CONTROL MMC3 TESCLK...
Page 28
IC601 LB8118M H FOCUS H TRACKING H SPINDLE H SLED FORWARD FORWARD FORWARD FORWARD REVERSE REVERSE REVERSE REVERSE DRIVE DRIVE DRIVE DRIVE – – VOUT1 VOUT2 MAXIMUM MAXIMUM 1CH/2CH ASP REF VALUE VALUE CHARGE SL REF 1.2V -OVER ERROR AMP –...
SECTION 8 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark may have some difference from the original are seldom required for routine service.
Page 32
(4) MECHANISM DECK SECTION (CDM-2911EBA) not supplied M602 M601 S603 The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified.
SECTION 9 JACK ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark are seldom required for routine service. parts list may be different from the parts speci- 0 are critical for safety.
Page 34
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C410 1-162-915-11 CERAMIC CHIP 10PF 0.5PF D407 8-719-056-07 LED SLR-342MC3F (LCD BACK LIGHT) C411 1-162-915-11 CERAMIC CHIP 10PF 0.5PF D408 8-719-056-07 LED SLR-342MC3F (LCD BACK LIGHT) D409 8-719-941-86 DIODE DAN202U C412 1-162-920-11 CERAMIC CHIP 27PF...
Page 35
MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R412 1-216-809-11 METAL CHIP 1/16W R471 1-216-864-11 METAL CHIP 1/16W R413 1-216-809-11 METAL CHIP 1/16W R472 1-216-864-11 METAL CHIP 1/16W R414 1-216-809-11 METAL CHIP 1/16W R473 1-216-864-11 METAL CHIP 1/16W R415 1-216-809-11 METAL CHIP...