1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 333 RJ SERIES
  6. Operator's manual

Husqvarna 333RJ, 335RJX-Series Operator's Manual

Husqvarna trimmer operator's manual
Hide thumbs Also See for 333RJ, 335RJX-Series:
Table of Contents

Quick Links

See also: Operator's Manual
Oper ator's manual (EPA)
333RJ 335RJ
X-series
Please r ead the operator's manual carefully and make sure you
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
understand the instructions before using the machine.
Table of Contents
loading

Related Manuals for Husqvarna 333RJ, 335RJX-Series

Summary of Contents for Husqvarna 333RJ, 335RJX-Series

  • Page 1 Oper ator’s manual (EPA) 333RJ 335RJ X-series Please r ead the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h understand the instructions before using the machine.

  • Page 2: Key To Symbols

    Arrows which show limits for handle positioning. Always wear approved protective gloves. Wear sturdy, non-slip boots. Only use non-metallic, flexible cutting attachments, i.e. trimmer heads with trimmer cord. 2 – English KEY TO SYMBOLS Starting instructions Other symbols/decals on the machine refer to special certification requirements for certain markets.

  • Page 3: Table Of Contents

    WARNING! A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual.

  • Page 4: Introduction

    Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.

  • Page 5: What Is What

    What is what on the clearing saw? 1 Trimmer head 2 Grease filler cap, bevel gear 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Handle adjustment 7 Loop handle 8 Suspension ring 9 Stop switch 10 Throttle lock...

  • Page 6: General Safety Precautions

    English Personal protective equipment IMPORTANT! A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual.

  • Page 7: Machine's Safety Equipment

    GENERAL SAFETY PRECAUTIONS CLOTHING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure hair so it is above shoulder level. FIRST AID KIT Always have a first aid kit nearby.
  • Page 8 GENERAL SAFETY PRECAUTIONS Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator. The guard also protects the operator from accidental contact with the cutting attachment. Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked.

  • Page 9: Cutting Equipment

    WARNING! Using an incorrect cutting attachment or an incorrectly sharpened blade increases the risk of kickback. Cutting equipment Grass blades and grass cutters are intended for cutting coarse grass. A trimmer head is intended for trimming grass. – 9 English...

  • Page 10: Sharpening Grass Cutters And Grass Blades

    • Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a couple of days.

  • Page 11: Assembly

    • Attach the J-handle to the loop handle using the three screws, as shown. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob. WARNING! Only grass blades/grass cutters or trimmer heads/plastic blades may be used when the J-handle is fitted.

  • Page 12: Fitting A Blade Guard, Grass Blade And Grass Cutter

    CAUTION! Ensure that the guard extension is fitted. Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft.

  • Page 13: Fuel Handling

    When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use HUSQVARNA two- stroke engine oil, which is specially formulated for our air- cooled two stroke-engines. • Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

  • Page 14: Fueling

    Mixing • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. •...

  • Page 15: Starting And Stopping

    • Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. • Never use the machine without a guard nor with a defective guard.
  • Page 16 STARTING AND STOPPING CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. CAUTION! Do not put any part of your body in marked area. Contact can result in burns to the skin, or electrical shock if the spark plug cap has been damaged.

  • Page 17: Working Techniques

    General working instructions IMPORTANT! This section describes the basic safety precautions for working with clearing saws and trimmers. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. Avoid all usage which you consider to be beyond your capability.

  • Page 18: Grass Clearing Using A Grass Blade

    Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. CAUTION! This technique increases the wear on the cord.

  • Page 19: Maintenance

    Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions...
  • Page 20 H. You should therefore fit the trimmer head T35 (2.7 mm cord) before adjusting the high speed jet. The cord length should be standard, i.e. to the knife on the trimmer guard. Apply full throttle and turn the high speed jet H very slowly clockwise until the engine slows down.

  • Page 21: Muffler

    However, before using the machine you should check that the bevel gear is filled three-quarters full with grease. Use HUSQVARNA special grease. The grease in the bevel gear does not normally need to be changed except if repairs are carried out.

  • Page 22: Air Filter

    Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor. Note: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically...

  • Page 23: Maintenance Schedule

    Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked. Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary. Check that the locking nut of the cutting equipment is tighten correctly.

  • Page 24: Technical Data Technical Data

    NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. Approved accessories Centre hole in blades/cutters, Ø 25,4 mm Output shaft thread M12 Grass blade/grass cutter Plastic blades Trimmer head Support cup 24 – English TECHNICAL DATA 333RJ 2,11/34,6...

  • Page 25: Federal Emission Control Warranty Statement

    The warranty period begins on the date small nonroad engine is delivered. LENGTH OF COVERAGE Husqvarna Forest & Garden warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years.
  • Page 27 8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...
  • Page 28 4,25 m 4,25 m 15 cm 6" 15 cm 6"...
  • Page 29 15 cm 6" 8,5 m 10 cm 4" 4,3 m "Clic"...
  • Page 30 15 cm 6" ´®z+R33¶5Q¨ ´®z+R33¶5Q¨ 10 m 10 cm 4" 4,3 m "Clic"...
  • Page 32 1150191-95 ´®z+R33¶5Q¨ ´®z+R33¶5Q¨ 2006-04-05...

This manual is also suitable for:

335rjx series

Table of Contents