Table of Contents
Quick Links
Instruction
manual
To learn more about Porter-Cable
visit our website at:
http://www.porter-cable.com
Copyright © 2005 Porter-Cable Corporation
ESPAÑOL: PÁGINA 17
FRANÇAISE : PAGE 35
Lock Mortiser and
Lock Face Templet
MODEL 517 Lock Face Templet
IMPORTANT
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ______________________________________
Type ___________________________________________
Serial No. _______________________________________
MODEL
513 Mortiser
Part No. 904667 - 01-24-05
Table of Contents
Related Manuals for DeWalt 513
Summary of Contents for DeWalt 513
- Page 1 FRANÇAISE : PAGE 35 Instruction Lock Mortiser and manual Lock Face Templet MODEL 513 Mortiser MODEL 517 Lock Face Templet IMPORTANT Please make certain that the person who is To learn more about Porter-Cable to use this equipment carefully reads and...
-
Page 2: Table Of Contents
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ......2 SAFETY GUIDELINES ........3 GENERAL SAFETY RULES . -
Page 3: Safety Guidelines
SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. -
Page 4: General Safety Rules
GENERAL SAFETY RULES Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 5 GENERAL SAFETY RULES continued d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
-
Page 6: Additional Specific Safety Rules
ADDITIONAL SPECIFIC SAFETY RULES Hold tool by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. - Page 7 ......two-phase alternating current ......two-phase alternating current with neutral ......three-phase alternating current ......three-phase alternating current with neutral ......rated current of the appropriate fuse-link in amperes ......time-lag miniature fuse-link where X is the symbol for the time/current characteristic, as given in IEC 60127 ......
-
Page 8: Carton Contents
* Mortiser frame FUNCTIONAL DESCRIPTION FOREWORD Model 513 Lock Mortiser permits builders and contractors to quickly cut true, accurate mortises for door box locks. Model 517 Lock Face Templet allows quick and economical routing for lock faces on doors after the mortise cut for the lock itself has been completed. -
Page 9: Operation
Fig. 2 ASSEMBLY OF MOTOR UNIT DISCONNECT TOOL FROM POWER SOURCE. Open hardware package and locate: two cap screws, two flat washers, " (4.0 mm) allen wrench. Place washers onto cap screws. Insert splined cutter shaft (see Fig. 3) through motor carriage (L) and into the spiral grooved bushing (M) in the main frame (N). - Page 10 DISCONNECT TOOL FROM POWER SOURCE and exercise extreme care when handling cutter to avoid bodily injury or damage to cutting edge. Thread selected bit onto end of splined cutter shaft and tighten securely. DETERMINING LENGTH OR HEIGHT OF CUT Measure the height of the lock box (see Fig. 5) including any protruding parts.
- Page 11 SETTING MORTISER FOR DEPTH OF CUT DISCONNECT TOOL FROM POWER SOURCE. Measure the lock box at its deepest part, including the thickness of the lock face, and add " (6.4 mm) to this dimension for clearance. The depth of cut is controlled by the feed rod (W) Fig.
- Page 12 Connect mortiser to power source. Turn motor switch ON and rotate crank (E) until collar (F) hits feed housing, stopping depth of cut and completing mortise. Turn motor OFF. DISCONNECT TOOL FROM POWER SOURCE. Move feed lever (A) to horizontal position to disengage feed mechanism. Grasp motor carriage (B), Fig.
- Page 13 PRODUCTION LOCK MORTISING If you have a number of doors with the locks at the same height, the height rod attachment (see Fig. 11) will be of great value. After you have determined the height you want, and have the lock mortiser in position on the first door, assemble the four rods that compose the height rod attachment.
- Page 14 LOCATING TEMPLET ON DOOR Draw a line across the door edge at the center of the mortise cut for the lock. Draw line (F), Fig. 12, on the templet side guides (C), midway between bars (B) and (E). Position templet on door so line (F) on templet matches line drawn on the door edge at the center of the mortise cut.
-
Page 15: Troubleshooting
TROUBLESHOOTING For assistance with your tool, visit our website at www.porter-cable.com for a list of service centers or call the Porter-Cable help line at 1-800-487-8665. MAINTENANCE KEEP TOOL CLEAN Keep the mortiser attachment free of dust and dirt, especially the vertical tubes on which the main frame slides. -
Page 16: Service
SERVICE REPLACEMENT PARTS When servicing use only identical replacement parts. For a service parts list or to learn more about Porter-Cable visit our website at www.porter-cable.com SERVICE AND REPAIRS All quality tools will eventually require servicing, or replacement of parts due to wear from normal use. -
Page 17: Español
PORTER-CABLE • DELTA SERVICE CENTERS (CENTROS DE SERVICIO DE PORTER-CABLE • DELTA) (CENTRE DE SERVICE PORTER-CABLE • DELTA) Parts and Repair Service for Porter-Cable • Delta Power Tools are Available at These Locations (Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta) (Locations où...