Sony DVP-S300 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. DVD Player
  5. DVP-S300
  6. Service manual
Sony DVP-S300 Service Manual

Sony DVP-S300 Service Manual

Hide thumbs Also See for DVP-S300:
Table of Contents

Quick Links

See also: Training Manual, Operating Manual
DVP-S300 / S305 / S315
SERVICE MANUAL
CD/DVD player
Signal format system
PAL/ (NTSC): DVP-A305/S315
NTSC
Audio characteristics
Frequncy response
DVD (PCM 96 kHz): 2 Hz to 44 kHz
(+0.5 dB, –2.0 dB)
DVD (PCM 48 kHz): 2 Hz to 22 kHz
(±0.5 dB)
CD: 2 Hz to 20 kHz (±0.5 dB)
Signal-to-noise ratio
More than 107 dB (LINE OUT (AUDIO)
connectors only)
Harmonic distortion
Less than 0.0028%
Dynamic range
More than 100 dB (DVD)
More than 97 dB (CD)
Wow and flutter
Less than detected value
(±0.001% W PEAK)
Outputs and inputs
jack
type
LINE OUT
Phono
(AUDIO)
jacks
DIGITAL OUT
Optical
(OPTICAL)
output
connector
DIGITAL OUT
Phono
(COAXIAL)
jacks
LINE OUT
Phono
(VIDEO)
jack
S VIDEO OUT
4-pin mini
DIN
PHONES
Phone
jack
MICROFILM
SPECIFICATIONS
: DVP-S300
Output
Load impedance
level
2 Vrms
Over 10 kilohms
(at 50 kilohms)
–18 dBm
Wave length: 660 nm
0.5 Vp-p
75 ohms terminated
1.0 Vp-p
75 ohms,
sync negative
Y: 1.0 Vp-p 75 ohms,
sync negative
C: 0.3 Vp-p 75 ohms terminated
12 mW
32 ohms
RMT-D103E/105A/105P
Singapore Model
General
Power requirements
220 – 240 V AC, 50 Hz: DVP-S305/S315
120 V AC, 60 Hz: DVP-S300
Power consumption
22 W: DVP-S305/S315
20 W: DVP-S300
430 × 95 × 325 mm (17 × 3
Dimensions (approx.)
(w/h/d): DVP-S300/S315
430 × 95 × 330 mm (w/h/d): DVP-S305
incl. projecting parts
Mass (approx.)
4.0 kg (8 lb 13 oz)
41 °F to 95 °F (5 °C to 35°C)
Operating temperature
Operating humidity
5% to 90%
Supplied accessories
• Audio/video/S-link connecting cord (1) (DVP-S300: US)
• Audio/Video connecting cord (1)
(DVP-S300: E/S305/S315)
• S video cable (1)
• Remote commander (remote) RMT-D103E (1) (DVP-S305)
• Remote commander (remote) RMT-D105A (DVP-S300)
• Remote commander (remote) RMT-D105P (DVP-S315)
• sony R6 (size AA) batteries (2)
Design and specifications are subject to change without notice.
US Model
DVP-S300
E Model
DVP-S300/S305
AEP Model
DVP-S315
UK Model
DVP-S315
Chinese Model
DVP-S305
Taiwan Model
DVP-S305
DVP-S305
× 12
3
/
7
/
in.)
4
8
CD/DVD PLAYER
Table of Contents
loading

Related Manuals for Sony DVP-S300

Summary of Contents for Sony DVP-S300

  • Page 1 Less than 0.0028% Dynamic range More than 100 dB (DVD) Supplied accessories More than 97 dB (CD) • Audio/video/S-link connecting cord (1) (DVP-S300: US) • Audio/Video connecting cord (1) Wow and flutter Less than detected value (DVP-S300: E/S305/S315) (±0.001% W PEAK) •...
  • Page 2 LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Section Title Page Section Title Page Service Note ................4 IC PIN FUNCTION DESCRIPTION GENERAL 5-1. Interface Control Pin Function (MB-78 Board IC604) .. 5-1 System Control Pin Function (MB-78 Board IC805) ..5-2 This Player Can Play the Following Discs ....1-1 Getting Started ..............

  • Page 4: Service Note

    SERVICE NOTE 1. DISASSEMBLY • This set can be disassembled in the order shown below. Case (Page 2-1) MB-78 Front Panel AU-197 Board Section Board (Page 2-1) (Page 2-1) (Page 2-1) MD Block Ass’y (Page 2-2) TK-47 Tray Board (Page 2-2) (Page 2-2) Optical Skew...
  • Page 5 2. NOTE ON REMOVE THE CASE 4. HOW TO SERVICE MB-78 BOARD 1) Remove six tapping screws. (See Fig. 1) 1) Remove the case from the set. (Refer to 2-1) 2) Open the side of case. (See Fig. 1) 2) Remove the cover (upper). (Refer to 2-3) 3) Remove the case as lift straight.
  • Page 6 5. NOTE ON MOUNTEING SLED MOTOR 1) Push the sled motor ass’y 1 toward direction A. (See Fig. 4) 2) Tighten two screws 2 (M1.7 × 2.5). 1 Sled motor ass’y 2 Two screws (M1.7 × 2.5) Fig. 4 3) Raising the MD block ass’y 3 90 º with the side down. confirm that the optical pick-up 4 falls by self weight.
  • Page 7 6. REPLACING OPTICAL PICK-UP 3) In handling the KHS-180A (RP), do not touch inhibited parts shown in Fig. 7, but grip the slide base bearing and U-shaped guide. 6-1. Handling 1) A red laser diode for DVD requires more attention to static Slide base bearing electricity than general infrared laser diodes for CD.
  • Page 8 7. NOTE ON ASSEMBLING MECHANICAL DECK 7-1. Application of Grease 1) Grease must be applied if the following parts were replaced. (See Fig. 8) Note 1: Recommended grease is Foil KG-70MP. Note 2: In applying grease, take care not to allow grease to stick to other parts (particularly, rubber belt, spindle motor, and optical pick-up) Base unit holder...
  • Page 9 7-2. Cleaning Spindle Motor Turntable 7-4. Deformation of Insulator 1) Remove the tray. (Refer to 2-7) 1) Assemble the spindle base into the base unit. 2) Clean the spindle motor turntable if disc antiskid rubber (black) 2) Lock with 4 shoulder screws. (See Fig. 11) is dirty.
  • Page 10 7-6. Note on Mounting TK-47 Board 1) Align two bosses. (See Fig. 13) 2) Align four tabs. (See Fig. 13) 3) Fix the board securely with 3 screws (BV3 × 10). (The sensor will not function normally if the board floats up.) Three screws (BV3 ×...

  • Page 11: General

    DVP-S300/S305/S315 SECTION 1 This section is extracted from GENERAL DVP-S315 instruction manual.
  • Page 20 1-10 1-10 E...

  • Page 21: Disassembly

    DVP-S300/S305/S315 SECTION 2 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. 2-1. CASE REMOVAL 2-3. MB-78 BOARD REMOVAL 7 Cover (upper) 5 Two screws 2 Two tapping screws 6 Three screws 1 Two tapping screws (B3) (B3)

  • Page 22: Md Block Ass'y Removal

    2-5. MD BLOCK ASS’Y REMOVAL 2-7. TRAY REMOVAL 1 Cover (lower) 1 Two screws (BVTP3 × 10) 2 Press pully bracket 3 Chassis bracket (B) 2 Two screws (B3) 4 Pull the tray. 6 Remove the 5 Two screws tray. 7 MD block ass’y (B3) 6 Clamp...

  • Page 23: Sled Motor (M501) Removal

    2-9. SLED MOTOR (M501) REMOVAL 2-11. OPTICAL PICK-UP REMOVAL 6 Two screws 4 Optical pick-up (P1.7 × 2.5) 4 Spindle base 5 Screw (PTTWH2 × 5) 3 Main shaft 2 Screw (PTTWH2 × 5) 7 Sled motor (M501) 2 Screw (P2 ×...

  • Page 24: Internal Views

    2-12. INTERNAL VIEWS Skew motor ass’y X-3947-138-1 Optical pick-up Optical pick-up (KHS-180A/J1N) Sled motor ass’y (KHS-180A/J1N) Sled motor ass’y 8-820-005-02 X-3947-137-1 8-820-005-02 X-3947-137-1 DC motor (spindle) 1-698-944-11 Motor (loading) 1-698-942-21 DC motor (spindle) 1-698-944-11...

  • Page 25: Circuit Boards Location

    2-13. CIRCUIT BOARDS LOCATION POWER BLOCK HS-930SF (S300: E/S305) Taiwan/E HS-930SH (S315) /S305 Chinese, Singapore HS-930SU (S300: US) MB-78 (SWITCHING REGULATOR) (SIGNAL PROCESS/SERVO) HP-96 (S300/S315) FG-43 AU-197 (HEAD PHONE) (SLED) (AUDIO) ME-15 (S305) (MIC IN) ER-2 (S315) (EURO AV) FR-133 (IR/POWER SWITCH) DC MOTOR (SPINDLE)

  • Page 26: Interface Control Pin Function (Mb-78 Board Ic604)

    5-1. INTERFACE CONTROL PIN FUNCTION (IC604 on MB-78 Board (6/8)) Pin No. Pin Name Function Pin No. Pin Name Function A16-19 Set Address 40, 41 AD2, 3 Input of AD 5, 6 TIN0, 1 – Not used – 7, 8 TOT0, 1 –...

  • Page 27: System Control Pin Function (Mb-78 Board Ic805)

    5-2. SYSTEM CONTROL PIN FUNCTION (IC805 on MB-78 Board (8/8)) Pin No. Pin Name Function Pin No. Pin Name Function PB14/IRQ6 Input of interrupt fromIC506 IRQ0 Input of interrupt fromIC203 PB15/IRQ7 Input of interrupt fromIC804 IRQ1 Input of DMA request from IC203 –...
  • Page 28 Pin No. Pin Name Function – Not used – Not used – Not used – Not used – Not used – Digital ground RxD0 Input of serial data TxD0 Output of serial data RxD1 Input of serial data TxD1 Output of serial data SCK0 Output of serial clock SCK1...

  • Page 29: Test Mode

    TEST MODE 6-1. Starting up Test Mode Syscon Diagnosis IF con Ver. 0.620 (9315) With the DVP-S300/S305/S315 turned off, press [TITLE], SYScon Ver. 0.400 (0000) [CLEAR], and [POWER] keys on the Remocon in this order, and →Enter item No.[02] ; 02 - Select Sub No.

  • Page 30: Error Display

    6-3. Error Display (3) Destination Setting (3-2) Destination setting Check In case of an error, the error code and information are displayed as shown in Figure 7. I/O port read Syscon Diagnosis Error: Not detected IF con Ver. 0.620 (9315) SYScon Ver.
  • Page 31 (5-4) Servo DSP Download (6) Data Source DSP (IC506) code area ROM/RAM discrimination (6-2) Register in ARP (IC806) RAM: Program download → Revision data read Register write → Register read matching check ROM: Revision data read Error 04: Data read error Error 05: Write/read data mismatch error 13: DSP data not ready Data from “0x00”...
  • Page 32 (6-6) Register in Decrypt IC (IC811) (7-3) Reset Line in 64020 Register write → Register read matching check Register write → Hard reset → Register read matching check Error 05: Write/read data mismatch error Error 02: Reset error 05: Write/read data mismatch error 0x00 –...
  • Page 33 (7-6) Connection from ARP (IC806) to 64020 (8-4) 1914 Vsync ROM data → ARP (IC806) → Decrypt (IC811) → AV Decoder CPU measures the 1914 Vsync interrupt cycle. (IC203) Error 41: Vsync interruption is not detected Error 04: Data read error 42: Vsync interrupt cycle error 05: Write/read data mismatch error 06: DMA transfer DREQ error...
  • Page 34 (8-8) S Terminal DC Check (8-13) AV CONT Through Check (DVP-S315) Color bar output by Video Encoder (IC252) Color bar output by video encoder Error 11: Serial transfer error Error 11: Serial transfer error The color bars are output in the same manner as in (8-2). Input picture is sent as it is from EURO AV2 (CNJ601) to the AV1 After VS signal is turned on/off repeatedly two times, the color (CNJ602).
  • Page 35 (9-5) Audio Digital Output (9-8) Dual DAC (Serial) ROM audio data → ARP (IC806) → AV Decoder (IC203) → Digi- ROM audio data → ARP (IC806) → AV Decoder (IC203) → 2ch DAC (IC215) → Analog audio output (Attenuation) tal audio I/F output Error 10: ARP (IC806) →...
  • Page 36 g Error Codes in Diagnostic Test 01: Mode not supported is selected 02: Reset error 03: Data write error 04: Data read error 05: Write/read data mismatch error 06: DMA transfer DREQ error 07: DMA transfer address error 10: Chip-to-chip data transfer error 11: Serial transfer error 12: EEPROM is not ready 13: DSP data is not ready...
  • Page 37 Drive Automatic Adjustment Flowchart DVD_SL Loading adjustment Adj. disc selection FOK Check STOP Tracking ON Select “ALL” Sled ON AGC ON CLVA EEPROM Default Set Lock Check STOP Hydet Init Sled Init Go To Home Position Auto Loop Filter Offset Auto Focus Offset Auto Tilt Offset Select “ALL”...
  • Page 38 DVD_SL adjustment adjustment Auto Loop Filter Offset FOK Check STOP Auto Focus Offset Auto Tilt Offset Auto Focus Offset Auto Focus Gain Auto Tracking Offset Auto Tracking Gain Auto EQ. Auto Loop Filter Offset Pull in Memory FOK Check STOP Jitter Check Tracking ON Sled ON...
  • Page 39 DVD_DL DVD_DL adjustment adjustment Disc Type Check FOK Check STOP Tracking ON LD ON Sled ON Spindle start CLVA Tilt ON Focus ON Lock Check FOK Check STOP Layer Check STOP sled move Auto Focus Offset Auto Tracking Offset Auto Tilt Offset Auto Focus Offset Auto Focus Gain Auto Tracking Gain...

  • Page 40: Drive Auto Adjustment

    6-5. Drive Auto Adjustment The tray opens after the ENTER key is pressed and the initializa- tion is finished. Then, place the DVD_SL disc for adjustment. Press the ENTER key to start adjustment. During adjustment, the tan- The drive can be automatically adjusted, except disc change and gential skew adjustment screen is displayed.

  • Page 41: Drive Manual Operation

    6-6. Drive Manual Operation 6-6-3. Manual Control 1 Manual Control 1 In performing manual operation, observe the following points: Select correct disc type on the Disc Type screen. SA.000000 SI.00 EMG.00 First, select “0. Disc TYpe” and execute “7. Hydet init” and “8. Sled init”.

  • Page 42: Manual Control 2

    6-6-4. Manual Control 2 9. LJ1→0 : After layer jump L1→L0, tracking loop turns →. FWD 1TJ : Jump one track forward. Manual Control 2 ←. RVS 1TJ : Jump one track reversely. SA.000000 SI.00 EMG.00 6-6-6. Manual Adjust 1 0.

  • Page 43: Manual Adjust 2

    6-6-7. Manual Adjust 2 3. Auto Focus Gain : Adjust focus gain automatically. Adjusted result is reflected on the EEPROM. Execute this with CLVA turned on if possible. If Manual Adjust 2 NG, the system will be defective, and re- SA.000000 SI.00 EMG.00...

  • Page 44: Eeprom Data Screen Display

    6-6-10. EEPROM data screen display EEPROM data Focus Offset Focus Gain TRK Offset TRK. CONT. TRK Gain Tilt Offset Pullin Level EQ. Boost L.F.O SD. ?? HY. ?? Figure 20 This screen displays various set values including adjusted results stored in the EEPROM. ID No.

  • Page 45: Electrical Adjustment

    DVP-S300/S305/S315 SECTION 7 ELECTRICAL ADJUSTMENT 7-1. Power Supply Check In making adjustment, refer to 7-4. Adjustment Related Parts Arrangement. 1. HS-930SF/930SH/930SU Board Note: During diagnostic check, the characters and color bars can Mode be seen only with the NTSC monitor. Therefore, for diag-...

  • Page 46: Adjustment Of System Control

    7-2. Adjustment of System Control 2. S-terminal Output Check (MB-78 board) Check S-terminal video output. If it is incorrect, pictures will not 1. 27MHz Free Run (MB-78 board) be displayed correctly in spite of connection to the TV with an S- ...

  • Page 47: Checking S Video Output S-C

    4. Checking Component Video Output R-Y 6. Checking S Video Output S-C (MB-78 board) (MB-78 board) (DVP-S315 only) This checks whether the S-C satisfies the NTSC Standard. If it is This checks component video output R-Y. If it is incorrect, cor- not correct, the colors will be too dark or light.

  • Page 48: Adjustment Related Parts Arrangement

    7-4. Adjustment Related Parts Arrangement MB-78 BOARD (Side A) RV251 VIDEO LEVEL IC206 CT201 27MHz FREERUN CN251 HS-930SF/930SH/930SU BOARD (Side A) CN201...
  • Page 49 MB-78 BOARD (Side B) CN252 7-5 E...

  • Page 50: Repair Parts List

    DVP-S300/S305/S315 SECTION 8 REPAIR PARTS LIST 8-1. EXPLODED VIEWS The components identified by mark ! or dotted line with mark ! are criti- cal for safety. NOTE: Replace only with part number speci- • The mechanical parts with no reference number in •...

  • Page 51: Front Panel Assembly

    4-963-404-21 EMBLEM (5-A), SONY 3-988-016-11 STICK, CURSOR (S305: E, Singapore) (S300/S305: E, Singapore/S315) 3-988-016-21 STICK, CURSOR (S305: Taiwan, Chinese) 4-963-404-81 EMBLEM (5-A), SONY (S305: Taiwan, Chinese) 1-500-386-11 FILTER, CLAMP (FERRITE CORE) (S315) 3-988-031-01 BUTTON, OPEN (S300/S315) 3-989-677-01 HOLDER 3-988-031-11 BUTTON, OPEN (S305: E, Singapore)

  • Page 52: Chassis Assembly

    8-1-3. CHASSIS ASSEMBLY supplied supplied S315 supplied Taiwan, Chinese supplied supplied AEP, UK, E, Singapore (S315) supplied supplied supplied S315 The components identified by mark ! or dotted line with mark ! are criti- supplied cal for safety. Replace only with part number speci- fied.

  • Page 53: Dvd Mechanism Chassis Assembly (1)

    8-1-4. DVD MECHANISM CHASSIS ASSEMBLY (1) supplied M902 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-975-090-01 TRAY 3-975-089-01 BRACKET, PRESS PULLEY 3-975-073-02 GEAR, CAM * 161 3-975-074-01 PULLEY, PRESS 3-975-087-01 GEAR, DRIVE 3-975-077-01 SCREW, BU STOPPER 3-975-086-01 GEAR, TRAY DRIVING * 163 3-975-088-01 HOLDER, BASE UNIT...

  • Page 54: Dvd Mechanism Chassis Assembly (2)

    8-1-5. DVD MECHANISM CHASSIS ASSEMBLY (2) M501 M903 M901 The components identified by mark ! or dotted line with mark ! are criti- cal for safety. Replace only with part number speci- fied. Ref. No. Part No. Description Remark Ref. No. Part No.

  • Page 55: Electrical Parts List

    DVP-S300/S305/S315 AU-197 8-2. ELECTRICAL PARTS LIST NOTE: The components identified by • Due to standardization, replacements in the • Items marked “*” are not stocked since they mark ! or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.
  • Page 56 AU-197 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark CN202 1-569-932-31 CONNECTOR, FFC/FPC 15P (S315) < COIL > CN203 1-774-769-11 CONNECTOR, FFC/FPC 25P CN205 1-573-733-11 PIN, CONNECTOR 6P (S300) L351 1-414-930-21 INDUCTOR 2.2uH CN205 1-573-733-21 PIN, CONNECTOR 6P (S315) L352 1-414-930-21 INDUCTOR 2.2uH...
  • Page 57 AU-197 ER-2 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R384 1-216-295-91 SHORT R305 1-216-025-91 RES, CHIP 1/10W R385 1-216-295-91 SHORT (S300/S315) R386 1-216-295-91 SHORT (S315) R314 1-216-041-00 METAL CHIP 1/10W (S305) R315 1-216-041-00 METAL CHIP 1/10W A-6065-108-A ER-2 BOARD, COMPLETE (S315) (S305)
  • Page 58 ER-2 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C675 1-163-251-11 CERAMIC CHIP 100PF FB720 1-414-553-11 FERRITE C676 1-163-251-11 CERAMIC CHIP 100PF FB721 1-414-553-11 FERRITE C686 1-163-251-11 CERAMIC CHIP 100PF FB722 1-414-553-11 FERRITE C687 1-163-251-11 CERAMIC CHIP 100PF FB723 1-414-553-11 FERRITE...
  • Page 59 ER-2 FG-43 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < RESISTOR > R675 1-216-049-91 RES, CHIP 1/10W R601 1-216-295-91 SHORT R676 1-216-049-91 RES, CHIP 1/10W R603 1-216-295-91 SHORT R679 1-216-079-00 METAL CHIP 1/10W R604 1-216-295-91 SHORT R680 1-216-069-00 METAL CHIP 6.8K...
  • Page 60 FL-88 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-6065-112-A FL-88 BOARD, COMPLETE R115 1-216-073-00 METAL CHIP 1/10W R116 1-216-073-00 METAL CHIP 1/10W ********************* (Ref.No.2,000 Series) R117 1-216-037-00 METAL CHIP 1/10W 3-988-021-01 HOLDER, FL R118 1-216-049-91 RES, CHIP 1/10W R119 1-216-091-00 METAL CHIP...
  • Page 61 FR-133 HP-96 M-78 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-6065-074-A FR-133 BOARD, COMPLETE < JACK > *********************** (Ref.No.2,000 Series) J001 1-568-519-41 JACK, LARGE TYPE (PHONES) < CAPACITOR > < TRANSISTOR > C401 1-126-205-11 ELECT CHIP 47uF 6.3V Q001...
  • Page 62 MB-78 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C207 1-162-970-11 CERAMIC CHIP 0.01uF C271 1-162-921-11 CERAMIC CHIP 33PF C208 1-162-970-11 CERAMIC CHIP 0.01uF (S300/S305) C209 1-162-970-11 CERAMIC CHIP 0.01uF C272 1-162-917-11 CERAMIC CHIP 15PF C210 1-162-970-11 CERAMIC CHIP 0.01uF C281...
  • Page 63 MB-78 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C382 1-107-826-11 CERAMIC CHIP 0.1uF C540 1-162-970-11 CERAMIC CHIP 0.01uF C383 1-107-826-11 CERAMIC CHIP 0.1uF C384 1-107-826-11 CERAMIC CHIP 0.1uF C541 1-128-004-11 ELECT CHIP 10uF C385 1-107-826-11 CERAMIC CHIP 0.1uF C542 1-107-826-11 CERAMIC CHIP...
  • Page 64 MB-78 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C814 1-162-970-11 CERAMIC CHIP 0.01uF CN361 1-784-688-21 PIN, CONNECTOR (PC BOARD) 2P C815 1-162-970-11 CERAMIC CHIP 0.01uF CN451 1-573-768-21 PIN, CONNECTOR (1.5MM) (SMD)5P C816 1-110-563-11 CERAMIC CHIP 0.068uF CN452 1-784-326-11 CONNECTOR (FFC) 27P...
  • Page 65 MB-78 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark FB803 1-500-283-11 INDUCTOR CHIP 0UH IC363 8-759-522-13 IC BA5981FP-E2 IC452 8-759-441-31 IC MC14053BDTR2 < FILTER > IC455 8-759-100-93 IC uPC393G2 FL001 1-233-893-21 FILTER, CHIP EMI IC501 8-759-100-93 IC uPC393G2 FL002 1-233-893-21 FILTER, CHIP EMI IC502...
  • Page 66 MB-78 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R028 1-216-864-11 METAL CHIP 1/16W R199 1-216-805-11 METAL CHIP 1/16W (S300: US/S305: E, Singapore) R200 1-216-801-11 METAL CHIP 1/16W R029 1-216-864-11 METAL CHIP 1/16W (S300: E/S315) R202 1-216-805-11 METAL CHIP 1/16W R030...
  • Page 67 MB-78 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R252 1-216-821-11 METAL CHIP 1/16W R290 1-216-829-11 METAL CHIP 4.7K 1/16W (S305) R291 1-216-805-11 METAL CHIP 1/16W R253 1-216-801-11 METAL CHIP 1/16W R292 1-216-833-11 METAL CHIP 1/16W (S305) (S315) R254...
  • Page 68 MB-78 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R362 1-216-821-11 METAL CHIP 1/16W R489 1-216-819-11 METAL CHIP 1/16W (S300: E/S305: Chinese, Taiwan) R490 1-216-839-11 METAL CHIP 1/16W R362 1-216-833-11 METAL CHIP 1/16W R491 1-216-833-11 METAL CHIP 1/16W R363 1-216-833-11 METAL CHIP...
  • Page 69 MB-78 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R559 1-216-809-11 METAL CHIP 1/16W R637 1-216-833-11 METAL CHIP 1/16W R560 1-218-847-11 RES, CHIP 0.50% 1/16W (S300: US/S305: E, Taiwan, Singapore) R561 1-216-837-11 METAL CHIP 1/16W R638 1-216-833-11 METAL CHIP 1/16W R562...
  • Page 70 MB-78 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R694 1-216-833-11 METAL CHIP 1/16W R855 1-216-833-11 METAL CHIP 1/16W (S300: US) R856 1-216-837-11 METAL CHIP 1/16W R695 1-216-864-11 METAL CHIP 1/16W (S300: E/S305/S315) R857 1-216-825-11 METAL CHIP 2.2K 1/16W R696...
  • Page 71 MB-78 ME-15 POWER BLOCK (HS-930) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R930 1-216-864-11 METAL CHIP 1/16W < JACK > R932 1-216-809-11 METAL CHIP 1/16W J801 1-507-854-00 JACK, PHONE (MIC) < VARIABLE RESISTOR > < COIL > RV251 1-238-663-11 RES, ADJ, CARBON 4.7K L801...
  • Page 72 POWER BLOCK (HS-930) TK-47 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C212 1-126-947-11 ELECT 47uF Q103 9-880-437-01 TRANSISTOR 2SK2798 (HS-930SU) C213 1-126-947-11 ELECT 47uF C214 1-126-947-11 ELECT 47uF Q103 9-880-444-01 TRANSISTOR 2SK2798 (HS-930SH) C301 1-126-960-11 ELECT Q103 9-880-450-01 TRANSISTOR 2SK2333 (HS-930SF) C311...
  • Page 73 TK-47 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C062 1-124-779-00 ELECT CHIP 10uF < TRANSISTOR > C064 1-124-779-00 ELECT CHIP 10uF C065 1-109-982-11 CERAMIC CHIP Q001 8-729-420-24 TRANSISTOR 2SB1218A-QRS C066 1-164-232-11 CERAMIC CHIP 0.01uF Q004 8-729-805-25 TRANSISTOR 2SB1121 Q005 8-729-805-25 TRANSISTOR 2SB1121...
  • Page 74 TK-47 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-575-335-21 CORD, CONNECTION (S-VIDEO CABLE 1.5m) R162 1-216-077-00 METAL CHIP 1/10W 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK) R163 1-216-081-00 METAL CHIP 1/10W 1-782-997-11 CORD, CONNECTION R164 1-216-295-91 SHORT (STEREO AV S LINK CABLE 1.5m) (S300: US) R165 1-216-295-91 SHORT...
  • Page 75 DVP-S300/S305/S315 Sony Corporation 98C0583-1 Printed in Japan © 1998. 3 9-921-680-11 Home A&V Products Company Published by General Engineering Dept. – 176 – (Osaki East)

This manual is also suitable for:

Dvp-s305Dvp-s315

Table of Contents