Husqvarna 289580 Owner's Manual
Husqvarna 289580 Owner's Manual

Husqvarna 289580 Owner's Manual

Ride on mower
Hide thumbs Also See for 289580:
03002
289580
(LGTH2454)
Owner's Manual
532 43 49-25 Rev. 2
Table of Contents
loading

Summary of Contents for Husqvarna 289580

  • Page 1 03002 289580 (LGTH2454) Owner's Manual 532 43 49-25 Rev. 2...
  • Page 2: Safety Rules

    SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • Slow down before turning. WARNING: In order to prevent ac ci den tal •...
  • Page 3 SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN Tragic accidents can occur if the operator is not alert to GENERAL SERVICE the presence of children. Children are often attracted to • Never operate machine in a closed area. the ma chine and the mowing activity.
  • Page 4: Table Of Contents

    PRODUCT SPECIFICATIONS CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manu fac tured to give Gasoline Capacity 4.0 Gallons you the best possible dependability and performance. and type: Unleaded Regular Should you experience any problem you cannot easily rem- Oil Type (API-SG-SL): SAE 30 (above 32°F) edy, please contact your nearest authorized servicecenter/...
  • Page 5: Assembly

    UNASSEMBLED PARTS Mower Mower Front Wheel (5) Large Retainer Springs - 7/16 (1) 3/4 O.D. Washers (1) Wheel (1) 1-1/4 O.D. Washer (2) Smaller Retainer Springs - 5/16 (5) 1-3/16 O.D. Washers (1) Locknut (1) Shoulder Bolt 3/8-16 (1) Anti-Sway Bar Slope Sheet (1) Oil Drain Tube For Future Use...
  • Page 6 ASSEMBLY TO ROLL TRACTOR OFF SKID (See Op er a tion BEFORE REMOVING TRACTOR FROM section for location and function of con trols) SKID • Raise attachment lift lever to its highest po si tion. TO CHECK BATTERY (See Fig. 1) •...
  • Page 7 ASSEMBLY 2. ASSEMBLE FRONT GAUGE WHEEL (W) TO FRONT NOTE: Be sure mower side suspension arms (A) are point- OF MOWER (See Fig. 5) ing forward before sliding mower under tractor. • Slide mower under tractor until it is centered under H.
  • Page 8 ASSEMBLY 7. ATTACH REAR LIFT LINKS (C) (See Fig. 13) • Insert rod end of rear lift link (C) into hole (U) in tractor lift ANTI-SWAY BAR TRANSAXLE (S) LOCATION BRACKET (T) shaft suspension arm and pivot link down to mower. LOCATED •...
  • Page 9 ASSEMBLY ✓ 9 INSTALL BELT ON ENGINE CLUTCH PULLEY (M) CHECKLIST (See Fig. 9 & 15) • Disengage belt tension rod (K) from locking bracket (L). BEFORE YOU OPERATE YOUR NEW TRAC TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST •...
  • Page 10: Operation

    OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. FAST SLOW REVERSE HIGH NEUTRAL CHOKE IGNITION SWITCH ENGINE START MOWER HEIGHT MOWER LIFT REVERSE ENGINE ON PARKING BRAKE ENGINE OFF OPERATION SYSTEM (ROS) CLUTCH/BRAKE...
  • Page 11: Operation

    OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Fig.
  • Page 12 OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs. We rec om mend standard safety glasses or a wide vision safety mask worn over spectacles.
  • Page 13 OPERATION TO MOVE FORWARD AND BACKWARD TO ADJUST GAUGE WHEELS (See Fig. 22) (See Fig. 20) Gauge wheels are prop er ly ad just ed when they are slight ly off the ground when mower is at the desired cutting height in The direction and speed of movement is controlled by the operating position.
  • Page 14 OPERATION REVERSE OPERATION SYSTEM (ROS) TO TRANSPORT (See Figs. 16 and 25) Your tractor is equipped with a Reverse Operation System When pushing or towing your tractor, be sure to disengage (ROS). Any attempt by the operator to travel in the reverse transmission by placing freewheel control in free wheel ing direction with the attachment clutch engaged will shut off po si tion.
  • Page 15: Before Starting The Engine

    OPERATION BEFORE STARTING THE ENGINE NOTE: Before starting, read the warm and cold starting procedures below. • Insert key into ignition and turn key clockwise to CHECK ENGINE OIL LEVEL “START” position and release key as soon as engine The engine in your tractor has been shipped, from the starts.
  • Page 16: Mowing Tips

    OPERATION MOWING TIPS PURGE TRANSMISSION • Mower should be properly leveled for best mowing CAUTION: Never engage or disengage performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. freewheel lever while the engine is run ning. •...
  • Page 17: Maintenance Schedule

    MAINTENANCE BEFORE EVERY EVERY EVERY EVERY EVERY BEFORE MAINTENANCE EACH SEASON STORAGE SCHEDULE HOURS HOURS HOURS HOURS Check Brake Operation Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades Lubrication Chart Check Battery Level Clean Battery and Terminals Clean Debris Off Steering Plate ck Transaxle Cooling...
  • Page 18: Maintenance

    MAINTENANCE TRACTOR BLADE CARE For best results mower blades must be kept sharp. Re place Always observe safety rules when per form ing any bent or damaged blades. main te nance. CAUTION: Use only a replacement blade ap- BRAKE OPERATION proved by the manufacturer of your tractor.
  • Page 19 MAINTENANCE V-BELTS OIL DRAIN VALVE Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not TO OPEN ad just able. Re place belts if they begin to slip from wear. TO CLOSE TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling.
  • Page 20: Deck Washout Port

    MAINTENANCE IN-LINE FUEL FILTER (See Fig. 32) DECK WASHOUT PORT (See Fig. 34) The fuel filter should be replaced once each season. If fuel Your tractor’s deck is equipped with a washout port on filter becomes clogged, ob struct ing fuel flow to car bu re tor, its surface as part of its deck wash system.
  • Page 21: Service And Adjustments

    SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Ensure transaxle is in the neutral position. • Place attachment clutch in “DISENGAGED” position. •...
  • Page 22 SERVICE AND ADJUSTMENTS TO LEVEL MOWER • If adjustment is necessary, see steps in Visual Adjust- ment instructions above. Make sure tires are properly inflated to the PSI shown on • Recheck measurements, adjust if necessary until both tires. If tires are over or under inflated, it may affect the sides are equal.
  • Page 23 SERVICE AND ADJUSTMENTS TO REPLACE MOTION DRIVE BELT 7. Reconnect clutch harness (A). (See Fig. 41) 8- Make sure belt is in all pulley grooves and in side all belt guides and keep ers. Park the tractor on level surface. En gage parking brake. For as sis tance, there is a belt installation guide decal on 9.
  • Page 24 SERVICE AND ADJUSTMENTS FRONT WHEEL TOE-IN/CAM BER Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.
  • Page 25 SERVICE AND ADJUSTMENTS TRANSMISSION INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to run REMOVAL/RE PLACE MENT poorly, stop running, or prevent it from starting. • Check wiring. See electrical wiring diagram in the Should your transmission require removal for service or repair parts section.
  • Page 26: Storage

    STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS WARNING: Never store the trac tor with FROM FORMING IN ES SEN TIAL FUEL SYSTEM PARTS SUCH gas o line in the tank inside a building AS CARBURETOR, FUEL FIL TER, FUEL HOSE, OR TANK...
  • Page 27: Trou Ble Shoot Ing

    TROUBLESHOOTING PROBLEM CAUSE CORRECTION 1. Out of fuel. 1. Fill fuel tank. Will not start 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4.
  • Page 28 TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues 1. Faulty operator-safety presence control 1. Check wiring, switches and connections. If not system. corrected, contact an authorized service center/ to run when oper- department. ator leaves seat with attachment clutch engaged 1. Worn, bent or loose blade. 1.
  • Page 29 SERVICE NOTES...
  • Page 30: Repair Parts

    TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 DECALS KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 532 42 91-96 Decal, Hood Logo 532 41 16-58 Decal, Fender Warning 532 42 49-29 Decal, Replacement 532 17 05-63 Decal, Warning...
  • Page 31 TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 SCHEMATIC SCH12 BATTERY SOLENOID STARTER FUSE AMMETER BLACK (OPTIONAL) ELECTRIC CLUTCH WHITE PTO SWITCH BLACK WHITE (DISENGAGED) WHITE BLACK GRAY CLUTCH/BRAKE (PEDAL UP) REVERSE SWITCH (NOT IN REVERSE) BLACK BLACK BLACK BLACK...
  • Page 32 TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 ELECTRICAL T07S With 12V Outlet Option With Service Minder Option...
  • Page 33 TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 ELECTRICAL KEY PART NO. NO. DESCRIPTION 532 16 34-65 Battery 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 532 18 64-91 Battery Box 532 17 61-38 Switch Interlock 532 18 37-59...
  • Page 34 TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 CHASSIS chassis-tex_TEX GT HUSQ_69...
  • Page 35 TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 CHASSIS KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 532 40 50-12 Logo 199 532 19 82-59 Plate Deck Lift 532 40 87-01 Dash 202 532 40 30-48 Vent Side Hood RH...
  • Page 36 TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 DRIVE drive-tex_K46_fender_14...
  • Page 37 TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 DRIVE KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION - - - - - - - - - Transaxle, TUFFTORQ K46 AW 174 532 19 72-89 Nut Push 532 18 62-11...
  • Page 38 TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 ENGINE SPARK ARRESTER KIT engine-tex_Kawa-2cyl_7...
  • Page 39 TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 ENGINE KEY PART NO. NO. DESCRIPTION - - - - - - Engine Kawa Model No. FR691V-AS06 532 14 97-23 Muffler 532 19 43-20 Keeper Belt Engine 532 17 93-35 Clutch Electric...
  • Page 40: Steering Assembly

    TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 STEERING ASSEMBLY KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 532 42 34-69 Wheel, Steering 873 94 08-00 Nut Hex Jam Toplock 1/2-20 unf 532 19 59-68 Axle Asm., Front 532 18 89-67 Washer Hardened .793 x 1.637 x .060...
  • Page 41: Seat Assembly

    TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 SEAT ASSEMBLY seat-tex_6.5SL_3 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 532 42 40-68 Seat 873 80 05-00 Nut, Lock 5/16-18 unc 532 19 76-61 Handle Slide Seat 532 18 01-66...
  • Page 42 TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 MOWER DECK...
  • Page 43: Mower Deck

    TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 532 40 31-25 Deck Weldment Mower 532 18 73-42 Baffle Right 532 19 60-66 Cover Mandrel LH 532 18 73-44...
  • Page 44: Mower Lift

    TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 MOWER LIFT lift-tex_23 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 532 42 20-27 Shaft Asm., Lift 532 19 42-08 Pin Cotter 5/16 Bow Tie Lock 532 19 52-30 Lever Asm., Lift RH...
  • Page 45: Repair Parts - Engine

    TRACTOR - - MODEL NUMBER (289580) KAWASAKI ENGINE - MODEL NUMBER FR691V, TYPE NUMBER AS06 CYLINDER/CRANKCASE PISTON/CRANKSHAFT VALVE/CAMSHAFT LUBRICATION-EQUIPMENT...
  • Page 46 TRACTOR - - MODEL NUMBER (289580) KAWASAKI ENGINE - MODEL NUMBER FR691V, TYPE NUMBER AS06 COOLING-EQUIPMENT CONTROL-EQUIPMENT ELECTRIC-EQUIPMENT CARBURETOR...
  • Page 47 TRACTOR - - MODEL NUMBER (289580) KAWASAKI ENGINE - MODEL NUMBER FR691V, TYPE NUMBER AS06 AIR-FILTER/MUFFLER STARTER FUEL-TANK/FUEL-VALVE LABEL...
  • Page 48 TRACTOR - - MODEL NUMBER (289580) KAWASAKI ENGINE - MODEL NUMBER FR691V, TYPE NUMBER AS06 CYLINDER/CRANKCASE LUBRICATION-EQUIPMENT 11004 11004-7026 Gasket-Head 13272 13272-7011 Plate,Rotor 11008 11008-7039 Head-Comp-Cylinder,#1 14075 14075-7013 Cap-Assy,Oil Gauge 11008a 11008-7040 Head-Comp-Cylinder,#2 16154 16154-7010 Rotor-Pump,Outer 11022 11022-7019 Case-Rocker,#1 16154a...
  • Page 49 TRACTOR - - MODEL NUMBER (289580) KAWASAKI ENGINE - MODEL NUMBER FR691V, TYPE NUMBER AS06 CARBURETOR VALVE/CAMSHAFT 11061 11061-7009 Gasket,Chamber 11055 11055-7009 Bracket 11061a 11061-7010 Gasket,Screw 12004 12004-7008 Valve-Intake 11061b 11061-7087 Gasket,Insulator 12005 12005-7009 Valve-Exhaust 11061c 11061-7088 Gasket,Insulator/Manifold 12009 12009-7001...
  • Page 50: Repair Parts - Transaxle

    TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 TUFFTORQ TRANSAXLE MODEL NUMBER K46AW MODEL K46AW 7A646084090 ACTUAL PARTS MAY NOT APPEAR AS SHOWN...
  • Page 51 TRACTOR - MODEL NO. (289580), PRODUCT NO. LGTH2454 TUFFTORQ TRANSAXLE MODEL NUMBER K46AW KEY PART NO. NO. DESCRIPTION 414395 VENT VALVE 15 414396 MAGNET 414397 MAGNET HOLDER 415923 PUMP SHAFT/BEARING KIT 414398 BYPASS LEVER 414399 SEALING CAP 30 414400 SNAP RING C 35...
  • Page 52 SERVICE NOTES...
  • Page 53 SERVICE NOTES...
  • Page 54 SERVICE NOTES...
  • Page 56 03.30.10 CL Printed in the U.S.A.

This manual is also suitable for:

Lgth2454

Table of Contents