Nokia MW1122 Administrator's Manual
  1. Manuals
  2. Brands
  3. Nokia Manuals
  4. Wireless Router
  5. MW1122
  6. Administrator's manual
Nokia MW1122 Administrator's Manual

Nokia MW1122 Administrator's Manual

Adsl/wlan router, t66520
Hide thumbs Also See for MW1122:
Table of Contents

Quick Links

Nokia MW1122
ADSL/WLAN Router
T66520
ADMINISTRATOR MANUAL
Table of Contents
loading

Related Manuals for Nokia MW1122

Summary of Contents for Nokia MW1122

  • Page 1 Nokia MW1122 ADSL/WLAN Router T66520 ADMINISTRATOR MANUAL...
  • Page 2 MW1122 ADSL/WLAN Router Administrator Manual C33902.20 A0 E Copyright Nokia Networks Oy C33902001SE_00...
  • Page 3 Please submit your comments to the nearest Nokia sales representative. NOKIA is a registered trademark of Nokia Corporation. Any other trademarks mentioned in the documents are the property of their respective owners.

  • Page 4: Document History

    Document History Document Date Comment C33902001SE_00 05.07.2000 E Copyright Nokia Networks Oy C33902001SE_00...
  • Page 5 MW1122 Administrator Manual E Copyright Nokia Networks Oy C33902001SE_00...

  • Page 6: Table Of Contents

    Contents Chapter 1 Introduction to Nokia MW1122 ....Chapter 2 Applications and features .....
  • Page 7 5.3.3 Wireless LAN page ....... 5-15 E Copyright Nokia Networks Oy C33902001SE_00...
  • Page 8 ........Glossary E Copyright Nokia Networks Oy C33902001SE_00...
  • Page 9 MW1122 Administrator Manual E Copyright Nokia Networks Oy viii C33902001SE_00...

  • Page 10: Introduction To Nokia Mw1122

    MW1122 allows you to connect your desktop and laptop PCs to remote networks. Your PCs must be equipped with either 10Base-T Ethernet interface or IEEE 802.11b standard compliant wireless LAN card, for example Nokia C110 or Nokia C111 PC card. There are also E Copyright Nokia Networks Oy C33902001SE_00...
  • Page 11 MW1122 Administrator Manual PCI cards and PC card adapters which can be used with desktop PCs. If you want to have more than one PC connected to a Nokia MW1122 modem through the Ethernet interface, you must use a multi-port Ethernet hub in between the PCs and Nokia MW1122 modem.

  • Page 12: Applications And Features

    Applications and features In this chapter, we present the most common applications and features of MW1122. The use and configuration of your Nokia MW1122 may be different from the configurations presented in this manual, even for similar applications. The configurations presented in this manual represent a typical way of using MW1122 for the corresponding applications.
  • Page 13 Internet address. Furthermore, it prevents others from seeing and accessing your private network and therefore it acts as a simple firewall. DSLAM 10Base-T network Wireless Customer premises Internet Wireless Internet connection Figure 2-1 High-speed Internet access E Copyright Nokia Networks Oy C33902001SE_00...

  • Page 14: Remote Work

    Applications and features Remote work Another application for MW1122 is remote work. In this case the end-to-end architecture can, for example, use PPP over Ethernet, where a dial-up-type PPP connection is created between your home PC and your corporate networks PPP access server based on the user name and password you issue in your PC.

  • Page 15: Lan Interconnection

    Especially, when the branch office is a small and possibly a temporary site without any existing LAN infrastructure available, the MW1122 is highly suitable for this purpose. In such circumstances the wireless LAN is an excellent technology to have office coverage fast and without any additional wiring installations.

  • Page 16: Interfaces

    In this manual it is called VBRIDGE. On the MW1122 web pages, the interface is called gateway or bridge IP interface. MW1122 can operate in four different main modes:...

  • Page 17: Lan And Wlan Interfaces

    Table 2-1 Operational modes LAN and WLAN interfaces LAN and WLAN interfaces can be configured individually to bridge and route packets. There are three different operational modes in both LAN and WLAN interfaces: E Copyright Nokia Networks Oy C33902001SE_00...

  • Page 18: Slaved Wlan Operation

    LAN and WLAN interfaces. Internal host/gateway interface There is a special host/gateway logical IP interface within MW1122 called VBRIDGE. This interface has a specific purpose in MW1122. In applications where some ATM virtual channel connections are used...

  • Page 19: Routing

    2.2.3 Bridging Bridging is supported to provide full protocol transparency. Bridging can be used simultaneously with IP routing. MW1122 works as a self-learning bridge supporting up to 1024 MAC addresses. Bridging is done between the Ethernet 10Base-T interface, the wireless LAN interface and each ATM VCC interface.
  • Page 20 IP and transport layer, the application that includes IP address and port within the payload will not work properly through NAPT. In many cases, these applications can be passed through the NAPT using Application Layer Gateway functionality (ALG). MW1122 has ALG for the following protocols/applications: ICMP H.323 including NetMeeting...

  • Page 21: Dynamic Host Configuration Protocol

    PCs on the home network. Two separate address ranges are used when LAN and WLAN are operating as separate subnets. MW1122 can also act as a DHCP relay agent and relay the DHCP requests to an external DHCP server.
  • Page 22 Windows The destination IP address must be MW1122 LAN/WLAN/VBRIDGE IP address depending on the configuration. PPP packets within PPTP are mapped to the configured VCC. MW1122 has three different ways to choose the ATM VCC that will be used for tunneling: Automatic, chooses the first free VCC Chooses the VCC number using C:number, where number is from 1 to 8.

  • Page 23: Point-To-Point Protocol Over Ethernet (Pppoe)

    MW1122 Administrator Manual 2.2.8 Point-to-Point Protocol over Ethernet (PPPoE) Standard PPPoE mode is used when MW1122 is operating as a bridge. PPPoE protocol defines how PPP sessions are mapped into Ethernet packets. When MW1122 operates as a bridge, this protocol is transparent to MW1122.

  • Page 24: Wired Encryption Privacy (Wep)

    2.2.13 Weighted Fair Queueing (Class of Service) As a Class of Service (CoS) function, MW1122 supports Weighted Fair Queueing (WFQ) for each ATM VCC. The CoS function ensures that different IP traffic flows are treated fairly in the upstream (towards the Internet) direction.
  • Page 25 MW1122 Administrator Manual MW1122 management (with telnet or Web browser) and it can be used to upload a new software to MW1122. The dedicated management channel is separated from the other IP stack. It is not possible to access the other interfaces or networks behind the data interfaces through the dedicated management channel.

  • Page 26: Chapter 3 Interfaces And Indicator Lights

    This chapter describes the external interfaces of MW1122 and introduces its front panel indicator lights. Interfaces MW1122 has one ADSL line interface and two LAN interfaces WLAN and 10Base-T Ethernet. It also has a local management interface (CLI) for management purposes. The ADSL line interface is compatible with ITU-T G.992.1 specification.

  • Page 27: Ethernet Interface

    Ethernet interface pin-out numbering 3.1.2 ADSL interface The ADSL interface (DSL) is compatible with ITU-T G.992.1 specification. The mechanical connector is a 6-pin RJ-11. The pin-out numbering is shown in Table 3-2. Figure 3-3 DSL connector E Copyright Nokia Networks Oy C33902001SE_00...

  • Page 28: Command Line Interface

    103 TxD <– Transmitted data 104 RxD –> Received data 105 RTS <– Request to send (not in use) 106 CTS –> Clear to send (const. ON) Table 3-3 Command line interface pin-out numbering E Copyright Nokia Networks Oy C33902001SE_00...

  • Page 29: Indicator Lights

    MW1122 Administrator Manual Indicator lights MW1122 has six indicator lights on the front panel: PWR, STA, WLAN, COL, ETH, and DSL. STA indicator is red. Other indicators are green. Figure 3-5 MW1122 front panel indicators GREEN ADSL link is down.
  • Page 30 Interfaces and indicator lights Stations on the WLAN but no traffic. Blinks Receives traffic through the WLAN interface. Hardware malfunction during startup. GREEN Power off. Power on. E Copyright Nokia Networks Oy C33902001SE_00...
  • Page 31 MW1122 Administrator Manual E Copyright Nokia Networks Oy C33902001SE_00...

  • Page 32: Chapter 4 Installing Nokia Mw1122

    Installing Nokia MW1122 Chapter 4 Installing Nokia MW1122 This chapter presents a step-by-step installation procedure of MW1122. Before starting the installation check that MW1122 is physically undamaged. The package contains the following items: MW1122 modem Wireless LAN card and antenna...

  • Page 33: Step-By-Step Installation Procedure

    Table 4-1 MW1122 default settings Step-by-step installation procedure 1. Plug the mains power cord to a mains outlet. 2. Plug the antenna into the antenna connector of the wireless LAN card, if needed. E Copyright Nokia Networks Oy C33902001SE_00...
  • Page 34 4. Switch on MW1122. The PWR indicator lights up. 5. Ensure that wireless LAN clients have the same configuration as the wireless LAN card in the MW1122 modem and that they are in the Infrastructure mode. The default wireless LAN configuration...
  • Page 35 MW1122 Administrator Manual splitter Figure 4-1 MW1122 and splitter connected Now, your MW1122 has been connected and you can check the connections according to your service provider’s instructions. See Chapter 5 Managing MW1122 for instructions on how to configure MW1122.

  • Page 36: Chapter 5 Managing Mw1122

    After the operational examples, we introduce the management methods of MW1122. First we show how to use the web browser management and then the command line interface (CLI) will be presented.

  • Page 37: Routing/Tunneling Ip Only

    If the application requires only routing of IP packets, an IP address should be configured for each interface in use. The example below shows a typical configuration in such a case. MW1122> show conf running ip address 192.168.1.1 255.255.255.0 wlan...

  • Page 38: Routing/Tunneling Ip, Bridging Other Protocols

    In the configuration example below, LAN and WLAN interfaces route IP traffic and bridge all other protocols. ATM VCC1 routes IP traffic and ATM VCC2 interfaces bridges all traffic. MW1122> show config running ip address 192.168.1.1 255.255.255.0 bridging wlan...

  • Page 39: Bridging Only

    192.168.1.1 255.255.255.0 MW1122> 5.1.4 Bridging only When only bridging is required, all ATM VCCs are configured as bridge. VBRIDGE IP address can be used as an optional management interface. MW1122> show config running bridging wlan network-name nokia radio-channel europe 13 bridging...

  • Page 40: Typical Configuration Tasks

    Note After you have made changes to the configuration, you must save the configuration if you want it to be active also after restarting MW1122. 5.2.1 Configuring DHCP and DNS The DHCP server can be enabled towards LAN, WLAN, and VBRIDGE ports.

  • Page 41: Configuring Static And Dynamic Routing

    5.2.2 Configuring static and dynamic routing Routing entries in the routing table are needed in order to forward the IP packets to the correct interface. MW1122 has both static and dynamic routes. Static routes are configured manually and dynamic routes are learned automatically using RIP v1 and RIP v2 protocols.

  • Page 42: Encrypting Wireless Connection

    1 to 4. In some WLAN products the numbering may be from 0 to 3. In those cases, key 0 equals key 1 in MW1122. Four keys are available to enable easy change of keys when the keys are changed at different times for different clients.

  • Page 43: Changing Wlan Settings Through The Command Line Interface

    MW1122. You can change this to suit your needs and make your network uniquely identifiable. To change the WLAN network name of MW1122: 1. Open a telnet or CLI session to MW1122 as described earlier in this chapter. 2. Start the configuration mode by typing...

  • Page 44: Controlling The Access To Your Network

    WLAN channels. Controlling the access to your network You can control the access to your MW1122 with an access list. By default, this feature is off in MW1122. This means that all WLAN clients are allowed to have access to your Nokia MW1122. Therefore it...

  • Page 45: File System And Downloading New Firmware Using Tftp

    You must activate the admission control to prohibit other WLAN clients from entering your network. To activate the access list: 1. Open a telnet or CLI session to MW1122 as described earlier in this chapter.Start the configuration mode by typing configure ENTER 2.

  • Page 46: Downloading Configuration Or Application From Monitor

    2. After you will see transfer status SUCCESSFUL message, restart MW1122 to activate the new software. Downloading configuration or application from monitor Monitor is a small application that is executed before the actual software image is started. Typically the Monitor automatically loads the application file image.exe.

  • Page 47: Browser Management

    You can use your PC’s web browser software to access the web configuration pages in MW1122. To access the web pages you must know the IP address of your MW1122 or, alternatively, the “name” that your MW1122 recognises. E Copyright Nokia Networks Oy...

  • Page 48: Opening A Connection

    To open a connection to the Nokia MW1122: 1. Start your web browser. 2. Enter the name (’MW1122’) or IP address of your Nokia MW1122 in the browser’s Open Location field and press Enter. If you use the IP address, it has to be assigned to a local port or gateway interface (VBRIDGE).

  • Page 49: Main Page

    5.3.2 Main Page Main Page is shown first when you use a web browser to connect to MW1122. The currently shown page is shown highlighted on the list on the left. Clicking an item on the list (Wireless LAN, WLAN Clients, Service Providers, Local Network, Statistics, Restart, and Save Config) takes you to the corresponding page.

  • Page 50: Wireless Lan Page

    LAN clients, wireless LAN network name and the channel in use. Software and hardware versions and the serial number of MW1122 are shown in the bottom of the page. 5.3.3 Wireless LAN page You can change wireless LAN network settings on the Wireless LAN page.
  • Page 51 Regulatory domain setting affects the available Radio channels. The radio channels corresponding to the regulatory domains are: Europe 1...13 France 10...13 Canada 1...11 1...11 Japan Change Transmit power if your wireless network becomes weak on the edges. E Copyright Nokia Networks Oy 5-16 C33902001SE_00...

  • Page 52: Wlan Clients Page

    WLAN Clients page Enabling access control You can add a wireless station to the Client table by typing its MAC address to the MAC address field and clicking the Add new button. Use E Copyright Nokia Networks Oy 5-17 C33902001SE_00...

  • Page 53: Encrypting Wireless Connection

    Key field and paste it to the wireless LAN client software. Then you can click the Apply to activate encryption. Note, that if you enable encryption on either client or MW1122 only, the wireless link will be disconnected until you have enabled encryption on both devices.
  • Page 54 Wifi mode provides lower authentication support but it supports all certified WLAN clients. Wifi mode is recommended if other than Nokia wireless LAN cards are used. Figures 5-5 and 5-6 show Wlan Clients page with default key and station-specific keys used, respectively.
  • Page 55 When you click the Apply button, the WLAN subsystem will be reseted. If you have enabled the access list or changed the encryption mode and you are accessing MW1122 through the wireless connection, the connection will be lost. You must reconfigure the wireless LAN client to continue configuration.
  • Page 56 Managing MW1122 Figure 5-6 WLAN Clients page and station-specific key encryption E Copyright Nokia Networks Oy 5-21 C33902001SE_00...

  • Page 57: Service Providers

    Service Providers page (Figure 5-8). The name can be used in your PPTP client for tunnel configuration, see section 2.2.7 Point-to-Point Tunneling Protocol. Figure 5-7 Service Provider page with PPP configuration E Copyright Nokia Networks Oy 5-22 C33902001SE_00...
  • Page 58 Managing MW1122 Figure 5-8 Service Providers page with PPTP configuration E Copyright Nokia Networks Oy 5-23 C33902001SE_00...

  • Page 59: Local Network

    For example, in Windows programs winipcfg.exe or ipconfig.exe must be used first to release the old address and then to renew to request new address. Figure 5-9 Local Network Local Ports page E Copyright Nokia Networks Oy 5-24 C33902001SE_00...

  • Page 60: Dhcp

    In Figure 5-10, scope (a) has been bound to Ethernet interface and scope (b) to WLAN interface. When the address ranges are not defined, MW1122 uses the default values for all DHCP parameters. The default values are: Start address is the interface IP address Subnet mask 255.255.255.0...
  • Page 61 MW1122 Administrator Manual Figure 5-10 Local Network DHCP page E Copyright Nokia Networks Oy 5-26 C33902001SE_00...

  • Page 62: Napt

    Server list. This example means that all TCP traffic coming from the Internet through VCC1 to ports 80...89 will be mapped to the IP address 192.168.1.15 ports 90...99 on your local network. Figure 5-11 Local Network NAPT page E Copyright Nokia Networks Oy 5-27 C33902001SE_00...

  • Page 63: Routing Page

    Subnet mask of the destination network, and the Gateway and the Interface through which the destination network can be reached. Then click the Add new button. There are two static routes in Figure 5-12. Figure 5-12 Local Network Routing page E Copyright Nokia Networks Oy 5-28 C33902001SE_00...

  • Page 64: Statistics Page

    Managing MW1122 5.3.7 Statistics page The Statistics page lets you view a selection of MW1122 statistics. to view statistics of a particular function, click the corresponding button and the statistics view is opened on a separate window. Figure 5-13 Statistics page...

  • Page 65: Restart Page

    MW1122 Administrator Manual 5.3.8 Restart page On the Restart page, you can reset subsystems and restart MW1122. Figure 5-14 Restart page E Copyright Nokia Networks Oy 5-30 C33902001SE_00...

  • Page 66: Save Config Page

    Figure 5-15 Save Config page Command line interface (CLI) MW1122 can be managed locally through a command line interface (CLI). The local command line interface is accessed through the local management console on the back panel. The local management console interface is an asynchronous V.24/V.28 character-based...
  • Page 67 The command line interface can also be accessed through the Ethernet and WLAN port of MW1122 or through the ATM channels of MW1122 on top of the telnet protocol. In order to use the CLI through telnet or the ATM channel, the IP function must be switched on and IP address must be given to the corresponding interface.
  • Page 68 The command line interface has been divided into two modes: main and configuration. The main mode lets you monitor the status and performance of MW1122. The configuration mode lets you change MW1122 configuration. The CLI is case sensitive. All commands must be given in lower case characters.

  • Page 69: Main Mode Commands

    MW1122(conf-vcc7)#vcc8 MW1122(conf-vcc8)#vbridge MW1122(conf-vbridge)#mngtvcc MW1122(conf-mngtvcc)#common MW1122(conf-common)#top MW1122(conf)#exit MW1122> 5.4.1 Main mode commands Command Show diagnostic log Description Displays diagnostic log. Syntax show log Arguments Example MW1122> show log 00/00:00:04 HI(1) ATM chann/vcc1/admin.stat up MW1122> E Copyright Nokia Networks Oy 5-34 C33902001SE_00...
  • Page 70 [all] Arguments show eth command shows Ethernet interface state and status. all argument shows also interrupts. Example MW1122> show eth ##eth(up) type IEEE 802.3/DIX stat-tx-payload 10964 672919 0 stat-rx-payload 10968 657690 0 MW1122> E Copyright Nokia Networks Oy 5-35 C33902001SE_00...
  • Page 71 ATM channels and traffic statistics. all shows all ATM information. Example MW1122> show atm ##vcc1(up) type encap DATA_PVC ETH-LLC stat-tx-payload 223641 2568289 0 stat-rx-payload 18030 1440816 0 MW1122> E Copyright Nokia Networks Oy 5-36 C33902001SE_00...
  • Page 72 Managing MW1122 Command Show bridge interface status Description Displays interfaces which have bridging enabled. Syntax show bridge if Arguments None Example MW1122> show bridge if VBRI (up) phys-address 00:99:12:16:10:53 ETH (up) phys-address 00:00:00:00:00:00 WLAN (up) phys-address 00:00:00:00:00:00 VCC1 (up) phys-address 00:00:00:00:00:00 MW1122>...
  • Page 73 MW1122 Administrator Manual Command Show bridging table Description Displays bridging table. Syntax show bridge table Arguments None Example MW1122> show bridge table phys-address type VBRI 00:99:12:16:10:53 n/a forever VCC1 00:60:08:94:da:a7 0 dynamic WLAN 00:e0:03:04:0c:c9 15 dynamic 00:60:08:94:af:d7 0 dynamic WLAN 00:e0:03:04:0c:e4 0...
  • Page 74 Managing MW1122 Command Show IP interfaces Description Displays IP interfaces. Syntax show ip if Arguments None Example MW1122> show ip if VBRIDGE (up) net-address net-mask phys-address 192.168.172.2 255.255.255.0 1500 00:99:12:16:10:53 as ETHERNET/RIP DISABLED MW1122> Command Show IP statistics Description Displays IP statistics.
  • Page 75 Show IP cache table and statistics Description Displays IP cache table and statistics. Syntax show ip cache Arguments None Example MW1122> show ip cache net-address phys-header 192.168.1.3 005004b67d680040430236720800 192.168.1.2 005004b669750040430236720800 VCC2 10.98.16.250 0021 nr-of-entries MW1122> E Copyright Nokia Networks Oy...
  • Page 76 WLAN route-dest route-mask netxthop 10.98.1.255 255.255.255.255 255.255.255.255BCAST 10.98.1.254 255.255.255.255 10.98.1.254 IFACE 10.98.1.0 255.255.255.0 192.168.1.254 LOCAL VCC3 route-dest route-mask netxthop 11.22.20.255255.255.255.255 255.255.255.255BCAST 11.22.20.108255.255.255.255 11.22.20.108 IFACE 11.22.20.0 255.255.255.0 11.22.20.108 LOCAL 0.0.0.0 0.0.0.0 11.22.20.1 STAT MW1122> E Copyright Nokia Networks Oy 5-41 C33902001SE_00...
  • Page 77 MW1122 Administrator Manual Command Show Internet Control Message Protocol statistics Description Displays ICMP statistics. Syntax show ip icmp Arguments None Example MW1122> show ip icmp in-msgs 23 out-msgs in-errors 0 out-errors in-dest-unreachs 0 out-dest-unreachs in-time-excds 0 out-time-excds in-parm-probs 0 out-parm-probs...
  • Page 78 Managing MW1122 Command Show Transmission Control statistics Description Displays TCP statistics. Syntax show ip tcp Arguments None Example MW1122> show ip tcp rto-algorithm VANJ estab-resets rto-min curr-estab rto-max 240000 in-segs max-conn out-segs active-opens retrans-segs passive-opens in-errs attemp-fails out-rsts MW1122> Command...
  • Page 79 Show Network Address Port Translation Protocol servers (pinholes) Description Displays NAPT server information. Syntax show napt server Arguments None. Example MW1122> show napt server VCC3 net-address port-mappings size prot “nat” 192.168.0.1 21<–>21 MW1122> E Copyright Nokia Networks Oy 5-44 C33902001SE_00...
  • Page 80 Description Displays DHCP server entry table and statistics. It also shows leased address and states. Syntax show dhcp server Arguments None. Example MW1122> show dhcp server ##scope (a) pool-address pool-last pool-mask 192.168.0.1 192.168.0.254 255.255.255.0 net-binding primary-dns secondary-dns 192.168.0.254...
  • Page 81 MW1122 Administrator Manual Command Show MW1122 information Description Displays MW1122 hardware and software information. Syntax show status [session | performance] Arguments Optional arguments session and performance. session shows information of the active configuration sessions. If login-id is used, it is shown on the screen.
  • Page 82 Syntax show config running Arguments None Example MW1122> show config running system hostname MW1122 ip address 192.168.172.148 255.255.255.128 wlan network name nokia radio channel europe 10 ip address 192.168.172.21...
  • Page 83 Show startup configuration Description Displays the startup configuration of your MW1122. This is the configuration saved in the startup.cfg file. Startup.cfg file is activated when MW1122 is switched on. If the startup.cfg file is missing, the default configur- ation is used. Syntax...
  • Page 84 Managing MW1122 Command Show default configuration Description Displays the default configuration of MW1122. MW1122 uses this configuration if the startup.cfg file is missing. Syntax show config default Arguments None Example MW1122> show config default system hostname Mxx bridging wlan regulatory-domain europe...
  • Page 85 IP function. Syntax ping Arguments ip-address is the IP address of the ping destination in dotted decimal format. Example MW1122> ping 198.168.172.23 Reply from 198.168.172.23: bytes 32 time <10ms TTL=128 MW1122> E Copyright Nokia Networks Oy 5-50 C33902001SE_00...
  • Page 86 ATM connection or the end-to-end connection. Example MW1122> atm ping 0 23 segment reply asserted roundtrip time = 4.20 ms MW1122> The debug commands are used to solve difficult problem situations.
  • Page 87 1454306 bytes MW1122> Command Copy file Description Copies files within MW1122 or over a TFTP (Trivial File Transfer Protocol) connection. With this command you can, for example, download configuration files. Syntax copy [file:/] [file:/] copy [file:/] tftp://<../dst- filename>...
  • Page 88 MW1122> Command Download new firmware Description Downloads a new firmware from a TFTP server. Re- member to restart MW1122 after downloading to acti- vate the new firmware. Syntax install tftp://<../src-filename> Arguments ip-address is the IP address of the TFTP server.
  • Page 89 Arguments log-filename is the name of the file in which you want to save the log. Example MW1122>save log file log.txt MW1122> Command Save log to a default file Description Saves log with a default file name (default.log).
  • Page 90 Command Restore configuration Description Restores the default or user configuration. You must have the admin privileges to issue this command. Re- start your MW1122 after you have issued this com- mand. Syntax restore config {default | user} Arguments default argument restores the default configuration of MW1122.
  • Page 91 If you provide a VCC number (vcc-id), only that connection will be reseted. arp clears the ARP table. bridge clears the bridge table. napt resets the NAPT subsystem. Example MW1122> reset wlan MW1122> E Copyright Nokia Networks Oy 5-56 C33902001SE_00...
  • Page 92 Arguments None Example MW1122> restart in progress... Command Switch to configuration mode Description Switches to the configuration mode. The configuration mode lets you change the configuration of MW1122. Syntax configure Arguments None Example MW1122>configure MW1122(conf)# E Copyright Nokia Networks Oy...

  • Page 93: Configuration Mode Commands

    MW1122 Administrator Manual 5.4.2 Configuration mode commands Command Return to root level Description Returns you to the root level from a higher configur- ation level. Syntax Arguments None. Example MW1122(conf-system)#top MW1122(conf)# E Copyright Nokia Networks Oy 5-58 C33902001SE_00...

  • Page 94: Root Level Commands

    Use the following commands to enter different configuration levels: system password wlan vcc1 ... vcc8 vbridge mngtvcc common E Copyright Nokia Networks Oy 5-59 C33902001SE_00...

  • Page 95: System Level Commands

    MW1122 Administrator Manual System level commands Command Assign hostname Description Assigns a hostname to MW1122. Syntax hostname Arguments name-string is an ASCII string of maximum of 32 characters. Example MW1122(conf-system)#hostname nokia nokia(conf-system)# Command Set configuration session timeout Description Sets a timeout for a management session.

  • Page 96: Password Level Command

    Example MW1122> admin nokia MW1122 Ethernet level commands Command Switch on/off bridging Description Switches on/off bridging. Syntax [no] bridging Arguments no switches bridging off. Example MW1122(conf-eth)#bridging MW1122(conf-eth)# E Copyright Nokia Networks Oy 5-61 C33902001SE_00...
  • Page 97 MW1122(conf-eth)# Command Switch on/off RIP send function in Ethernet inter- face Description Switches on/off RIP send function. When enabled MW1122 sends Routing Information Protocol messages to other routers. Syntax [no] ip rip-send {rip-send-mode} Arguments no switches rip-send function off. v1 send-mode selects RIP version 1.
  • Page 98 Command Switch on/off RIP receive function in Ethernet inter- face Description Switches on/off RIP send function. When enabled MW1122 receives Routing Information Protocol mess- ages from other routers. Syntax [no] ip rip-receive {rip-receive-mode} Arguments no switches RIP receive function off.

  • Page 99: Wlan Level Commands

    The available channels depend on the region setting. Channel numbers (ch-number) for different regions are: Europe 1...13 France 10...13 Canada 1...11 1...11 Japan Example MW1122(conf-wlan)#radio-channel europe 10 MW1122(conf-wlan)# E Copyright Nokia Networks Oy 5-64 C33902001SE_00...
  • Page 100 Syntax [de] beacon-interval Arguments de sets the default beacon interval 200. value is the time interval in milliseconds, 1...65535. Example MW1122(conf-wlan)#beacon-interval 3000 MW1122(conf-wlan)# E Copyright Nokia Networks Oy 5-65 C33902001SE_00...
  • Page 101 MW1122 Administrator Manual Command Set DTIM interval Description Sets the DTIM (Delivery Traffic Indication Message) time interval at which MW1122 will send its broadcast traffic. Syntax [de] dtim-interval Arguments de sets the default interval 2. value is an integer 1...255.
  • Page 102 LAN. Syntax [no] admission-control Arguments no switches admission control off. mode argument is sta-address when you want to re- strict access by defining a list of permitted addresses. Example MW1122(conf-wlan)#admission-control sta-address MW1122(conf-wlan)# E Copyright Nokia Networks Oy 5-67 C33902001SE_00...
  • Page 103 Select default encryption key Description Selects which default key is used. Syntax [no] wep default-key Arguments no switches default key off. id argument can be 1, 2, 3 or 4. Example MW1122(conf-wlan)#wep default-key 1 MW1122(conf-wlan)# E Copyright Nokia Networks Oy 5-68 C33902001SE_00...
  • Page 104 1, 2, 3 or 4. key-length can be 40-bit or 128-bit. key-value is a hexadecimal string of 10 (40-bit) or 32 (128-bit) characters. Example MW1122(conf-wlan)#wep key-entry 1 40-bit 1234567890 MW1122(conf-wlan)# Command Define access control list Description Defines a list of addresses (Client table) which are per- mitted to join the wireless LAN.
  • Page 105 [no] ip address Arguments no switches IP function off. ip-address is the IP address you want to assign to the wireless LAN interface. ip-mask is the subnet mask. Example MW1122(conf-wlan)#ip address 192.168.132.12 255.255.255.0 MW1122(conf-wlan)# E Copyright Nokia Networks Oy 5-70 C33902001SE_00...
  • Page 106 Managing MW1122 Command Switch on/off RIP send function in wireless LAN in- terface Description Switches on/off RIP send function. When enabled, MW1122 sends Routing Information Protocol messages to other routers. Syntax [no] ip rip-send {rip-send-mode} Arguments no switches rip-send function off.

  • Page 107: Vcc (Atm Channel) Commands

    MW1122 Administrator Manual Command Disable/enable management through the wireless LAN interface Description Enables/disables the management of MW1122 through the wireless LAN interface. Syntax [no] ip admin-disabled Arguments no enables management through the wireless LAN in- terface. Example MW1122(conf-wlan)#ip admin-disabled MW1122(conf-wlan)#...
  • Page 108 Sets the password used in PPP authentication. Syntax [no] ppp password Arguments no deletes PPP password. passwd-string is the PPP password. The password must be 4...15 characters long. Example MW1122(conf-vccx)#ppp password jfddslfj MW1122(conf-vccx)# E Copyright Nokia Networks Oy 5-73 C33902001SE_00...
  • Page 109 255.255.255.0 MW1122(conf-vccx)# Command Switch on/off RIP send function on ATM channel Description Switches on/off RIP send function. When enabled, MW1122 sends Routing Information Protocol messages to other routers. Syntax [no] ip rip-send {rip-send-mode} Arguments no switches rip-send function off. v1 send-mode selects RIP version 1.
  • Page 110 Managing MW1122 Command Switch on/off RIP receive function on ATM channel Description Switches on/off RIP receive function. When enabled, MW1122 receives Routing Information Protocol mess- ages from other routers. Syntax [no] ip rip-receive {rip-receive-mode} Arguments no switches RIP receive function off.
  • Page 111 Example MW1122(conf-vccx)#ip server-napt web_server 192.168.1.100 80 80 1 tcp MW1122(conf-vccx)# Command Disable/enable management through the ATM chan- Description Enables/disables the management of MW1122 through the ATM channel. Syntax [no] ip admin-disabled Arguments no enables management through the ATM channel. Example...

  • Page 112: Vbridge Commands

    255.255.255.0 MW1122(conf-vbridge)# Command Switch on/off RIP receive function in vbridge Description Switches on/off RIP receive function. When enabled, MW1122 receives Routing Information Protocol mess- ages from other routers. Syntax [no] ip rip-receive {rip-receive-mode} Arguments no switches RIP receive function off.

  • Page 113: Dedicated Management Channel Commands

    Virtual Channel Identifier of the ATM chan- nel. Possible values are 0...65535. encap is the encapsulation of the ATM channel. En- capsulations are ppp-vc, eth-llc, and ip-llc. Example MW1122(conf-mngtvcc)#pvc 0 100 eth-llc MW1122(conf-mngtvcc)# E Copyright Nokia Networks Oy 5-78 C33902001SE_00...

  • Page 114: Common Commands

    Description Sets the maximum size of the received PPP packets. Syntax [de] ppp mru Arguments size is the size of a PPP packet. Default size is 1500. Example MW1122(conf-common)#ppp mru 1000 MW1122(conf-common)# E Copyright Nokia Networks Oy 5-79 C33902001SE_00...
  • Page 115 MW1122 Administrator Manual Command Set PPP restart time parameter Description Defines how long MW1122 waits for the configure-re- quest packet. Syntax [de] ppp restart
  • Page 116 Example MW1122(conf-common)#ip route 131.112.11.1 255.255.255.0 131.2.111.2 mngtvcc MW1122(conf-common)# E Copyright Nokia Networks Oy 5-81 C33902001SE_00...
  • Page 117 Description You can define up to four IP addresses from which MW 1122 can be accessed using telnet or http. f you define one or more addresses, MW1122 can be accessed from the specified addresses only. Syntax [no] ip host-acl ...
  • Page 118 DHCP pool (1 or 2). class defines whether the server is a primary or a secondary server. dns-server is the IP address of the DNS server. Example MW1122(conf-common)#dhcp dns 1 primary 190.168.2.1 MW1122(conf-common)# E Copyright Nokia Networks Oy 5-83 C33902001SE_00...
  • Page 119 Arguments scope defines the DHCP pool (1 or 2). time-count is the renewal interval in minutes, 1...65535. Example MW1122(conf-common)#dhcp lease-time 1 360 MW1122(conf-common)# Command Set DHCP pool domain name Description Set the domain name for the DHCP pool. The domain name is used to show the client in which network the client is in.
  • Page 120 MW1122(conf-common)# Command Switch between full-rate ADSL and ADSL lite Description Switches between full-rate ADSL and ADSL lite. Note, G.992.2. Syntax [no] misc dmt-mode-lite Arguments no switches to full-rate ADSL. Example MW1122(conf-common)#misc dmt-mode-lite MW1122(conf-common)# E Copyright Nokia Networks Oy 5-85 C33902001SE_00...
  • Page 121 MW1122 Administrator Manual E Copyright Nokia Networks Oy 5-86 C33902001SE_00...

  • Page 122: Technical Specifications

    DIXv2 (transmit), IEEE 802.3 and DIXv2 (re- ceive) Ethernet connectors RJ-45 Wireless LAN interface Wireless LAN IEEE 802.11b DSSS Data connector PC Card slot type 2 Routing Routing protocols RIPv1, RIPv2, and static routes E Copyright Nokia Networks Oy C33902001SE_00...
  • Page 123 Management through payload Management proto- Telnet/TCP/IP for command line interface, cols TFTP/UDP/IP for software and configuration download, HTTP/web server Indicator lights ADSL line status Ethernet activity and status WLAN Wlan activity and status Ethernet collision E Copyright Nokia Networks Oy C33902001SE_00...

  • Page 124: Mechanical Construction And Power Supply

    Technical specifications Features MW1122 startup error Power on A.1 Mechanical construction and power supply MW1122 is a stand-alone device which can also be wall-mounted. Mechanical construction Width 225 mm Height 65 mm Depth 230 mm Weight 1 kg Table A-1 Mechanical construction MW1122 has an in-built power supply.

  • Page 125: Emc

    MW1122 Administrator Manual MW1122 complies with the following specifications provided that the device is connected to an earthed socket outlet: Emission EN55022: 1998 class B Immunity EN55024: 1998 EN300386-2: 1997 Overvoltage ITU-T K.21 Safety Safety EN60950 E Copyright Nokia Networks Oy...
  • Page 126 Ethernet Internet protocol Internet service provider L2TP Layer 2 tunneling protocol Local area network Logical link control Media access control Personal computer POTS Plain old telephone system Point-to-point protocol PPTP Point-to-point tunneling protocol E Copyright Nokia Networks Oy Glossary-1 C33902001SE_00...
  • Page 127 Character-based man-machine interface where a command line end- ing with character is used to configure a device. The device in- terprets the command and returns a character-based response. E Copyright Nokia Networks Oy Glossary-2 C33902001SE_00...

  • Page 128: Mac Address

    Ethernet address. multiplexer A device where several logical connections are combined into one physical connection. POTS filter A device used for separating the telephone signal from data signals in the digital subscriber line. E Copyright Nokia Networks Oy Glossary-3 C33902001SE_00...

  • Page 129: Web Browser

    A concatenation of virtual channel links that extends between the points where the ATM service users access the ATM layer. virtual path A unidirectional logical association of virtual channels. web browser A software that is used to browse the World Wide Web. E Copyright Nokia Networks Oy Glossary-4 C33902001SE_00...

Table of Contents