Makita 3710 Instruction Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Laminate Trimmer
  5. 3710
  6. Instruction manual
Makita 3710 Instruction Manual

Makita 3710 Instruction Manual

Hide thumbs Also See for 3710:
Table of Contents

Quick Links

See also: Instruction Manual
Trimmer
MODEL 3710
I N S T R U C T I O N
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
DOUBLE
INSULATION
M A N U A L
006628
Table of Contents
loading

Related Manuals for Makita 3710

Summary of Contents for Makita 3710

  • Page 1 Trimmer MODEL 3710 006628 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

  • Page 2: Specifications

    Responsible manufacturer: Power supply Makita Corporation Anjo Aichi Japan The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated on single-phase AC supply. They...

  • Page 3: General Safety Rules

    GENERAL SAFETY RULES GEA001-2 WARNING: Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains- operated (corded) power tool or battery-operated (cordless) power tool.

  • Page 4: Additional Safety Rules

    Remove any adjusting key or wrench sures reduce the risk of starting the power before turning the power tool on. A wrench tool accidentally. or a key left attached to a rotating part of the Store idle power tools out of the reach of power tool may result in personal injury.
  • Page 5 13. Do not touch the bit immediately after operation; Make sure the bit is not contacting the work- piece before the switch is turned on. it may be extremely hot and could burn your skin. Before using the tool on an actual workpiece, let 14.

  • Page 6: Functional Description

    FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Adjusting bit protrusion 006631 To adjust the bit protrusion, loosen the clamping nut and move the tool base up or down as desired by turning the adjusting screw.
  • Page 7 Switch action 006614 To start the tool, move the switch lever to the I (ON) position. To stop the tool, move the switch lever to the O (OFF) position. 1. Switch lever ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.

  • Page 8: Operation

    OPERATION Turn the tool on without the bit making any contact with the workpiece and wait 006633 until the bit attains full speed. Then move the tool over the workpiece surface, keeping the tool base and trimmer shoe flush with the sides of the workpiece. NOTE: •...
  • Page 9 Remove the tool base from the tool. Loosen the wing bolts and secure the tool 006640 base horizontally. Loosen the two screws on the tool base. 1. Screws 2. Wing bolt 3. Base 4. Screwdriver Place the templet guide on the tool base. There are four convex portions on 006641 the templet guide.
  • Page 10 Attach the guide plate to the straight guide with the bolt and the wing nut. 006617 1. Bolt 2. Guide plate 3. Straight guide 4. Wing nut 006635 1. Clamp screw (A) 2. Straight guide 3. Wing nut 4. Base 5.
  • Page 11 For cutting circles between 121 mm and 221 mm in radius. 006620 NOTE: • Circles between 172 mm and 186 mm in radius cannot be cut using this guide. 1. Wing nut 2. Guide plate 3. Straight guide 4. Center hole 5.

  • Page 12: Maintenance

    To maintain product SAFETY and RELIABILITY, repairs, any other mainte- nance or adjustment should be performed by Makita Authorized Service Cent- ers, always using Makita replacement parts. 1. Screwdriver...
  • Page 13 CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
  • Page 14 Drill point double flush trimming bit 005121 006488 1/4" Corner rounding bit 005125 006489 1/4" 1/4" Chamfering bit 005126 006462 30˚ 30˚ 30˚ E 1/4" 45˚ 45˚ 45˚ E 1/4" 60˚ 60˚ 60˚ E 1/4" Cove beading bit 005129 006464 1/4"...
  • Page 15 Ball bearing corner rounding bit 005131 006466 1/4" 1/4" Ball bearing chamfering bit 005132 006467 45˚ 45˚ 45˚ E 1/4" 60˚ 60˚ 60˚ E 1/4" Ball bearing beading bit 005133 006468 1/4" 1/4" Ball bearing cove beading bit 005134 006469 1/4"...
  • Page 16 Makita Corporation Anjo, Aichi, Japan 884630-229...

Table of Contents