Table of Contents
Quick Links
Table of Contents
Related Manuals for Black & Decker 900142
Summary of Contents for Black & Decker 900142
-
Page 1: User Manual
Model # 900142: Page 1 Bottom Loading Bottled Water Dispenser Model # 900142 USER MANUAL TO REDUCE THE RISK OF INJURY AND PROPERTY DAMAGE, USER MUST READ THIS MANUAL BEFORE ASSEMBLING, INSTALLING & OPERATING DISPENSER. SAVE THIS MANUAL FOR FUTURE USE... -
Page 2: Safety Precautions
Model # 900142: Page 2 SAFETY PRECAUTIONS To reduce risk of injury and property damage, user must read this entire manual before assembling, installing & operating dispenser. Failure to execute the instructions in this manual can cause personal injury or property damage. -
Page 3: Table Of Contents
Model # 900142: Page 3 TABLE OF CONTENTS Safety Precautions …………………………………………… Key Information for Future Use ……………………………. Specifications ………………………………………………… Parts & Features …………………………………………….. Assembly ……………………………………………………… Installation ……………………………………………………. Operation …………………………………………………….. Proper Care & Cleaning ……………………………………. Troubleshooting ……………………………………………… 11 Limited Warranty ……………………………………………… 12... -
Page 4: Specifications
Model # 900142: Page 4 SPECIFICATIONS Power Supply 5 AMPs Refrigerant Type R-134A Cold Water Power 125 Watts Cold Capacity / Hour 1.0 Gallons Cold Temp Range 39qF – 59qF Hot Water Power 425 Watts Hot Capacity / Hour 1.0 Gallons Hot Temp Range 149qF –... -
Page 5: Assembly
Model # 900142: Page 5 ASSEMBLY Keep plastic bags away from children. Remove dispenser from packaging. Unpack drip tray and insert into dispenser. Properly dispose all of packaging. INSTALLATION Place dispenser upright. Locate dispenser on a hard and level surface in a cool shaded location near a grounded wall outlet. - Page 6 Model # 900142: Page 6 Initial Set Up Notice: To prevent damage to compressor, allow unit to sit upright for at least 4 hours prior to operating. Open door. If using a 5 gallon bottle use the bottle probe as it is supplied. If you desire to use a lighter weight 3 gallon bottle, remove the bottom half of the probe by pulling it apart.
- Page 7 Model # 900142: Page 7 Setting Clock 1. Press and hold in MODE button until clock digits flash. 2. Press button to select desired hour including AM or PM. Press SET to save. 3. The minutes will now flash. 4. Press button to select desired minutes.
-
Page 8: Hot Water Tap
Model # 900142: Page 8 Blinking Cup & Glass This dispenser is equipped with a feature to inform you when the heating and cooling functions are operating. When the hot cup is blinking it indicates the dispenser is heating water. -
Page 9: Proper Care & Cleaning
Model # 900142: Page 9 Push red hot water release button inward and depress hot water control downward to start flow. Release hot water control once desired fill level is achieved. Replacing an Empty Bottle Notice: When the bottle icon on the digital screen is blinking, you are either low on water or the seal between the probe and bottle is not complete. -
Page 10: Cleaning Water Tanks And Lines
Model # 900142: Page 10 Cleaning Water Tanks and Lines Perform: Every 3 months or whenever an off-taste occurs. Time Required: 30 minutes. Note: Best to do prior to loading a fresh bottle. Turn energy saving switch to OFF. Unplug power cord from wall outlet. -
Page 11: Troubleshooting
Model # 900142: Page 11 TROUBLESHOOTING Dispenser does not operate. Make sure the power cord is properly connected to a working outlet. Water is leaking. Bottle may have a leak. Remove bottle and replace with new bottle. If leak remains, remove probe from bottle and call 866-429-7566 for assistance. -
Page 12: Limited Warranty
Model # 900142: Page 12 LIMITED WARRANTY Primo Water Corporation, (“Vendor”) warrants to the original purchaser of this dispenser, and to no other person, that if this dispenser is assembled and operated in accordance with the printed instructions accompanying it, then for a period of two (2) years from the date of purchase, all parts in such dispenser shall be free from defects in material and workmanship.