Available languages
Available languages
Quick Links
el
ifa =
Built-In 30" Electric
-':I
Combination
Wall Ovens
403 WEST FOURTH STREET, NORTH
NEWTON, IA 50208
COMBINATION
[,,:[0_f _W_'1 ! m[oIV_=l_l __o]_l
1-1/4" Dia. Conduit Access Hole*
5/8" Plywood Floor (Must Support 250 lbs.)
DIMENSIONS
in
cm
A
30 MIN
76.20 MIN
B
24 MIN
60.96 MIN
C
47 + 1/16
119.38 +.16
D
24 MIN
60.96
E
28-1/2 + 1/16
72.39 + .16
F
47-5/8
120.97
G
29-3/4
75.57
H
24-7/16
62.07
I
4 to 20
10.2 to 50.8
* Hole must be cut as close to corner
of cabinet
as possible.
l_[o_
Do not block air intake slots along bottom of oven.
i
1
WALLOVEN
CUTOUT
}
INSTALLATION
1. Cut hole in cabinet to mount oven. Cutout in
cabinet should be level and straight.
NOTE: There are no provisions to level the unit
after it is installed. An oven that is not level could
cause poor baking results.
2. Install plywood floor as shown above.
3. Install top mounting bracket - also refer to
template. (figure 3)
Top bracket mounting
installation
instructions:
a. Before installing unit into the cabinet, open
microwave door, remove the two upper screws in
the trim kit holding the top mounting bracket (see
figure
1 next page) and set the bracket and
screws to the side.
b. Using scissors cut along the cut line on the
template (provided).
c. Find the center of the cabinet cutout.
d. Align the template "center of opening" to the
center of the cabinet cutout making sure the top
of the cabinet cutout corresponds with the
template "top of opening" indicator line. Tape may
be used to hold the template temporarily in place.
e. Locate and mark screw holes (A) at both
ends, 2 each side, of template.
f. Remove template and set it to the side.
g. Drill pilot holes into cabinet using 7/64" or
#35 drill bit.
h. Install top mount bracket (from step 3a) to
cabinet with the provided wood screws. (1/2" X 4)
CAUTION
For European style cabinets (flush front) the required
clearance for operation of the oven door is minimum
spacing of 7/8" between the cutout and the door, hinge
or drawer of the cabinet.
Some built-in cabinets may not be wide
enough, due
to their construction,
to allow this installation.
Top bracket mounting installation instructions:
(continued)
i. Install and push unit in until trim frame engages with top
mount bracket.
j. Drive two screws that were removed in step (a) Do not
over tighten the screws.
4. Attach unit to the cabinet with 4 No. 8, flat head screws
supplied inside of envelope containing these instructions.
Pre-drill holes in cabinet for attachment screws using 1/8,
drill. Oven mounting holes are provided in side trim.
5. See instructions "Electrical Connections" for electrical
hook-up.
6. See figure 2 next page for lower trim installation.
7. See User's Manual for operating instructions.
8101 P744-60
(11-06-00)
Related Manuals for Jenn-Air JMW8330DAB15
Summary of Contents for Jenn-Air JMW8330DAB15
- Page 1 ifa = Built-In 30" Electric 403 WEST FOURTH STREET, NORTH -':I Combination Wall Ovens NEWTON, IA 50208 COMBINATION WALLOVEN CUTOUT [,,:[0_f _W_'1 ! m[oIV_=l_l __o]_l 1-1/4" Dia. Conduit Access Hole* 5/8" Plywood Floor (Must Support 250 lbs.) DIMENSIONS 30 MIN 76.20 MIN 24 MIN 60.96 MIN...
- Page 2 ELECTRICAL CONNECTIONS Unit to be properly circuit protected and wired according to local electrical code and National Electrical Code. MOUNT BRACKET It is advisable that the electrical wiring and hookup be accomplished by a competent electrician. 120/240 VAC or 120/208 VAC 60 Hz. See serial plate on each unit for power requirements.
- Page 3 Hornos electricos 403 WEST FOURTH STREET, NORTH empotrados de pared NEWTON, IA 50208 combinados de 30" [,:t0_d ___ Im] = Inl'_[oJ=]_[o] Im] = 11 t ]-'_-'! = lm] CORTE COMBINADO HORNO DE PARED 1-1/4" Di&. Orificio de acceso del conductor* 5/8"...
- Page 4 CONEXIONES ELI_CTRICAS Soporte superior El circuito de la unidad debe estar protegido y cableado de montaje correctamente y de acuerdo con los c6digos electricos locales y con el C6digo Electrico Nacional. Es recomendable que el cableado y las conexiones electricas las realice un electricista competente. 120/240 VCA o 120/208 VCA, 60 Hz.
-
Page 5: Mise En Service
Fours electriques mixtes 403 WEST FOURTH STREET, NORTH NEWTON, IA 50208, €:TATS-UNIS encastres de 30 po DI_COUPE POUR LE FOUR ENCASTRE MIXTE J Plancher en contreplaqu6 de 5/8 po (dolt pouvoir supporter 250 Ib) DIMENSIONS D---_ 30 MIN. 76,2 MIN. 24 MIN. -
Page 6: Entretien
RACCORDEMENT ._, L'i=LECTRICITie Support de mon- Le circuit utilise par I'appareil doit 6tre correctement tage sup6rieur proteg6 et c&ble conformement au code d'61ectricit6 local et au << National Electrical Code _. II est recommande que le c&blage et le raccordement 61ectrique soient effectu6s par un 61ectricien competent.