Cisco CAtalyst 4500 Series Installation Manual

Cisco CAtalyst 4500 Series Installation Manual

Hide thumbs Also See for CAtalyst 4500 Series:
Table of Contents

Quick Links

Catalyst 4500 Series Switches
Installation Guide
December 2005
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel:
408 526-4000
800 553-NETS (6387)
Fax:
408 526-4100
Customer Order Number: DOC-7814409=
Text Part Number: 78-14409-08
Table of Contents
loading

Summary of Contents for Cisco CAtalyst 4500 Series

  • Page 1 Catalyst 4500 Series Switches Installation Guide December 2005 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Customer Order Number: DOC-7814409= Text Part Number: 78-14409-08...
  • Page 2 You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...
  • Page 3 CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco...
  • Page 5 Obtaining Additional Publications and Information xxiii Product Overview C H A P T E R Switch Features Catalyst 4503 Switch Features Catalyst 4506 Switch Features Catalyst 4507R Switch Features 1-10 Catalyst 4510R Switch Features 1-14 Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 6: Table Of Contents

    C H A P T E R Electrostatic Discharge Preventing Electrostatic Discharge Damage Site Power Requirements and Heat Dissipation Power Connection Guidelines for AC-Powered Systems Power Connection Guidelines for DC-Powered Systems 2-12 Calculating DC Input Current 2-13 Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 7 Installing a DC-Input Power Supply 4-16 Required Tools 4-16 Installation Procedure 4-16 Removing and Replacing the Chassis Fan Assembly 4-18 Required Tools 4-22 Removing the Fan Assembly 4-23 Installing the Fan Assembly 4-23 Verifying the Installation 4-24 Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 8 Catalyst 4506 Switch Specifications Catalyst 4507R Switch Specifications Catalyst 4510R Switch Specifications Catalyst 4500 Series Power Supplies Repacking a Switch A P P E N D I X N D E X Catalyst 4500 Series Switches Installation Guide viii 78-14409-08...
  • Page 9 Preface This preface describes the audience, organization, and conventions of the Catalyst 4500 Series Switches Installation Guide and provides information on how to obtain related documentation and technical assistance. Audience Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS3260) should install, replace, or service the equipment.
  • Page 10: Appendix B Repacking A Switch

    Related Documentation Refer to the following documents for additional Catalyst 4500 series information: For information about individual switching modules and supervisors refer to • the Catalyst 4500 Series Module Installation Guide at: http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/hardware/mod...
  • Page 11 Terminal sessions and information that the system screen displays are in font. screen Information that you must enter is shown in boldface screen boldface font font. screen Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 12 Cautions use the following conventions: Means reader be careful. In this situation, you might do something Caution that could result in equipment damage or loss of data. Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 13 Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla. SÄILYTÄ NÄMÄ OHJEET Catalyst 4500 Series Switches Installation Guide xiii 78-14409-08...
  • Page 14 Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. CONSERVARE QUESTE ISTRUZIONI Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 15 Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONES Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 16 Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 17 Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.
  • Page 18 Preface Obtaining Documentation and Submitting a Service Request Catalyst 4500 Series Switches Installation Guide xviii 78-14409-08...
  • Page 19: Product Overview

    Power Supplies, page 1-34 • System Architecture, page 1-43 • Switch Features The following sections describe the features of the Catalyst 4500 series switches: Catalyst 4503 Switch Features, page 1-2 • Catalyst 4506 Switch Features, page 1-6 • Catalyst 4507R Switch Features, page 1-10 •...
  • Page 20 1000BASE-T, shortwave SX, LX/LH, and ZX interfaces, or CWDM and DWDM GBICs. For a description of GBICs, refer to the Catalyst 4500 Series Module Installation Guide or the Catalyst 4500 Series Supervisor Engines and Switching Modules Installation Note. Some supervisor engines use SFP modules for Gigabit Ethernet connections, or X2 modules for 10-Gigabit Ethernet connections.
  • Page 21 (control path) Features interface monitoring, environmental status, and SNMP and • console/Telnet interface Packets are not forwarded while the module is removed; a system Note reboot occurs when a supervisor engine is reinserted. Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 22 48-port 10/100-Mbps Fast Ethernet switching module (WS-X4148-RJ) 48-port 100BASE-BX10-D Fast Ethernet switching module • (WS-X4148-FE-BD-LC) 48-port 10/100-Mbps Fast Ethernet switching module (WS-X4148-RJ21) • 48-port Cisco pre-standard Power over Ethernet (PoE) • 10/100BASE-TX switching module (WS-X4148-RJ45V) 48-port 100BASE-X Fast Ethernet switching module • (WS-X4248-FE-SFP) 24-port IEEE 802.3af-compliant PoE 10/100BASE-TX switching module...
  • Page 23 Access Gateway Module (WS-X4604-GWY) • Backplane channel module (WS-X4019) • 1. You will need to configure the 1400 W DC input current as appropriate for the model of switch. Refer to Appendix A, “Specifications.” Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 24 1000BASE-T, shortwave SX, LX/LH, and ZX interfaces, or CWDM and DWDM GBICs. For a description of GBICs, refer to the Catalyst 4500 Series Module Installation Guide or the Catalyst 4500 Series Supervisor Engines and Switching Modules Installation Note. Some supervisor engines use...
  • Page 25 Power supplies Supports a 1000 W, 1300 W, 1400 W, 2800 W, or 4200 W AC-input • power supply or a 1400 W DC-input single or triple-input power supply Optional redundant power supply • Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 26 48-port 100BASE-BX10-D Fast Ethernet switching module • (WS-X4148-FE-BD-LC) 48-port 10/100-Mbps Fast Ethernet switching module • (WS-X4148-RJ21) 48-port Cisco pre-standard Power over Ethernet (PoE) • 10/100BASE-TX switching module (WS-X4148-RJ45V) 24-port IEEE 802.3af-compliant PoE 10/100BASE-TX switching • module (WS-X4224-RJ45V) 48-port IEEE 802.3af compliant PoE 10/100BASE-TX RJ-45 switching •...
  • Page 27 Access Gateway Module (WS-X4604-GWY) • Backplane channel module (WS-X4019) • 1. You will need to configure the 1400 W DC input current as appropriate for the model of switch. Refer to Appendix A, “Specifications.” Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 28 1000BASE-T, shortwave SX, LX/LH, and ZX interfaces, or CWDM and DWDM GBICs. For a description of GBICs, refer to the Catalyst 4000 Series Module Installation Guide or the Catalyst 4500 Catalyst 4500 Series Switches Installation Guide 1-10 78-14409-08...
  • Page 29 Can support a 1000 W, 1300 W, 1400 W, 2800 W, or 4200W AC-input power • supply or a 1400 W DC-input single or triple-input power supply Optional redundant power supply • Catalyst 4500 Series Switches Installation Guide 1-11 78-14409-08...
  • Page 30 With a single supervisor, packets are not forwarded while the module is Note removed; a system reboot occurs when a supervisor engine is reinserted. In redundant systems, removing the active supervisor causes the standby supervisor to become active. Catalyst 4500 Series Switches Installation Guide 1-12 78-14409-08...
  • Page 31 48-port 100BASE-BX10-D Fast Ethernet switching module • (WS-X4148-FE-BD-LC) 48-port 10/100-Mbps Fast Ethernet switching module (WS-X4148-RJ21) • 48-port Cisco pre-standard Power over Ethernet (PoE) • 10/100BASE-TX switching module (WS-X4148-RJ45V) 48-port 100BASE-X Fast Ethernet switching module (WS-X4248-FE-SFP) • Catalyst 4500 Series Switches Installation Guide...
  • Page 32 (WS-X4548-GB-RJ45V) Access Gateway Module (WS-X4604-GWY) • 1. You will need to configure the 1400 W DC input current as appropriate for the model of switch. Refer to Appendix A, “Specifications.” Catalyst 4500 Series Switches Installation Guide 1-14 78-14409-08...
  • Page 33 The Gigabit Ethernet ports can be configured with any combination of copper 1000BASE-T, shortwave SX, LX/LH, and ZX interfaces, or CWDM and DWDM GBICs. For a description of GBICs, refer to the Catalyst 4500 Series Module Catalyst 4500 Series Switches Installation Guide...
  • Page 34 Chapter 1 Product Overview Switch Features Installation Guide or the Catalyst 4500 Series Supervisor Engines and Switching Modules Installation Note. Some supervisor engines use SFP modules for Gigabit Ethernet connections, or X2 modules for 10 Gigabit Ethernet connections. Refer to the installation note for your supervisor engine for more details on these modules.
  • Page 35 With a single supervisor, packets are not forwarded while the module is Note removed; a system reboot occurs when a supervisor engine is reinserted. In redundant systems, removing the active supervisor causes the standby supervisor to become active. Catalyst 4500 Series Switches Installation Guide 1-17 78-14409-08...
  • Page 36 • 48-port 100BASE-BX10-D Fast Ethernet switching module • (WS-X4148-FE-BD-LC) 48-port 10/100-Mbps Fast Ethernet switching module (WS-X4148-RJ21) • 48-port Cisco pre-standard Power over Ethernet (PoE) • 10/100BASE-TX switching module (WS-X4148-RJ45V) 24-port IEEE 802.3af-compliant PoE 10/100BASE-TX switching module • (WS-X4224-RJ45V) 48-port IEEE 802.3af compliant PoE 10/100BASE-TX RJ-45 switching •...
  • Page 37 Appendix A, “Specifications.” 2. 1000W AC and 1300W AC power supplies will fit and function; however, power management is cautioned and ony some configurations will have adequate power. Please refer to the Cisco Power Calculator at http://tools.cisco.com/cpc/ before configuring these power supplies.
  • Page 38: Supervisor Engines

    Supervisor Engine V-10GE (WS-X4516-10GE) (Figure 1-12) • E-series supervisor engines may in some cases also work on Catalyst 4500 series Note systems, refer to the installation note for your supervisor engine for details. The Catalyst 4500 series supervisor engines have the following features:...
  • Page 39: Supervisor Engines

    (WS-X4516-10GE and interconnection of high-performance switches and routers WS-X4013+10GE) Forwarding Layer 2, 3, and 4 forwarding (Cisco IOS only) Supervisor Engine II 24-Gbps, 18 Mpps full-duplex Gigabit Ethernet switching engine Supervisor Engine II-Plus 64 Gbps, 48 Mpps (with Catalyst 4506 and 4507R, or 28-Gbps, 21 Mpps...
  • Page 40 Series NetFlow Services Card (WS-F4531). The Supervisor Engine V-10GE supports NetFlow services without a NetFlow Services Card. To install the supervisor engine, refer to the procedure in the Catalyst 4500 Series Module Installation Guide. The various supervisor engine models are shown in...
  • Page 41 STATUS LED Gigabit uplink ports Switch load indicators CompactFlash port CONSOLE port (RJ-45) Management port Figure 1-7 Catalyst 4500 Series Supervisor Engine II-Plus TS (WS-X4013+TS) RESET button STATUS LED PoE status Switch load Compact Flash port indicators Ethernet management port...
  • Page 42 10 GE uplink Gigabit SFP Switch load ports ports indicators Figure 1-9 Supervisor Engine III (WS-X4014) RESET button STATUS LED Gigabit uplink ports Switch load indicators Compact Flash port CONSOLE port Management port Catalyst 4500 Series Switches Installation Guide 1-24 78-14409-08...
  • Page 43 CONSOLE Compact port Flash port Figure 1-11 Supervisor Engine V (WS-X4516) RESET button STATUS LED Gigabit uplink ports Switch load Ethernet indicators management port CONSOLE Compact port Flash port Catalyst 4500 Series Switches Installation Guide 1-25 78-14409-08...
  • Page 44: Leds

    LEDs, page 1-27 • Gigabit Ethernet Uplink Ports, page 1-27 • Ethernet Management Port, page 1-29 • CONSOLE Port, page 1-29 • RESET Button, page 1-29 • • CompactFlash Port, page 1-29 Catalyst 4500 Series Switches Installation Guide 1-26 78-14409-08...
  • Page 45 The Gigabit Ethernet uplink ports operate in full-duplex mode only. GBICs have SC connectors to interface with multimode fiber (MMF) and single-mode fiber (SMF) cable. For more information about GBICs, refer to the Catalyst 4500 Series Module Installation Guide. Catalyst 4500 Series Switches Installation Guide 1-27 78-14409-08...
  • Page 46: 10-Gigabit Ethernet Uplink Ports

    WS-X4013+TS, WS-X4516-10GE and WS-X4013+10GE supervisors, as well as some switching modules. These ports use the 1000BASE-SX, 1000BASE-LX, Cisco Coarse Wave Division Multiplexing (CWDM ) SFPs, 1000BASE-T SFP, and 1000BASE-ZX SFP. SFP connectors vary with interface type and may use multimode fiber (MMF), single-mode fiber (SMF) cable, or copper Ethernet cables.
  • Page 47: Console Port

    When using Cisco IOS Release 12.2(50)SG or later, this port can also perform the same functions as the console port. For earlier Cisco IOS software releases, this port is not active while the switch is operating normally.
  • Page 48: Fan Assembly

    1-14. Catalyst 4507R airflow is shown in Figure 1-15. Catalyst 4510R airflow is shown Figure 1-16. You must install module filler plates on unused switching module slots to ensure Caution proper airflow. Catalyst 4500 Series Switches Installation Guide 1-30 78-14409-08...
  • Page 49 Chapter 1 Product Overview Fan Assembly Figure 1-13 Catalyst 4503 Airflow 45 06 Fan assembly Figure 1-14 Catalyst 4506 Airflow 45 06 Fan assembly Catalyst 4500 Series Switches Installation Guide 1-31 78-14409-08...
  • Page 50 E-TX ETHE RNE ST AT MUL TI-SP GIGA BIT SWIT CHIN ETHE RNE G MOD 10/10 0BAS E-TX ETHE RNE Fan assembly MUL TI-SP GIGA BIT ETHE RNE SWIT CHIN G MOD Catalyst 4500 Series Switches Installation Guide 1-32 78-14409-08...
  • Page 51 E-TX ETHE RNE ST AT MUL TI-SP GIGA BIT SWIT CHIN ETHE RNE G MOD 10/10 0BAS E-TX ETHE RNE MUL TI-SP GIGA BIT ETHE RNE SWIT CHIN G MOD Fan assembly Catalyst 4500 Series Switches Installation Guide 1-33 78-14409-08...
  • Page 52: Power Supplies

    For detailed specifications on all Catalyst 4500 series power supplies, refer to the Note “Catalyst 4500 Series Power Supplies” section on page A-8. A Catalyst 4500 series switch can use a 1000 W, 1300 W, 1400 W, 2800 W (see Figure 1-17), or 4200 W (with two inputs, see Figure...
  • Page 53 The 4200 W AC power supply should not be used in mixed-voltage Note configurations. All the inputs in a chassis must be the same voltage (110 or 220 V). Figure 1-19 1400 W DC-Input Power Supply Captive screws Catalyst 4500 Series Switches Installation Guide 1-35 78-14409-08...
  • Page 54 The Catalyst 4510R requires at least 1400 W of input power. (The 1000 W AC and 1300 W AC power supplies for the Catalyst 4500 series will fit and function in a Catalyst 4510R; however, power management may be required in high density configurations.) Cisco recommends the use of the 1400 W DC, 1400 W AC, and...
  • Page 55: Power Supply Leds

    Chapter 1 Product Overview Power Supplies When power is removed from one power supply on a Catalyst 4500 series switch that has two power supplies, the redundant power feature causes the second power supply to produce full power. To replace a power supply, see the “Removing and Replacing the Power Supply”...
  • Page 56: Power Supply Fan

    Load-Sharing Feature When you install and turn on a second power supply on a Catalyst 4500 series switch, it provides approximately one-half of the required power to the system. If one power supply fails, the other power supply immediately assumes full power to maintain uninterrupted system operation.
  • Page 57: 1400 W Dc Triple-Input Power Supply Operational Modes

    For more details on how the supervisor engine monitors the power supplies, refer to the “Environmental Monitoring and Power Management” chapter of the Catalyst 4500 Series Switch Cisco IOS Software Configuration Guide. 1400 W DC Triple-input Power Supply Operational Modes...
  • Page 58 OUTPUT FAIL LED shows a false failure. The C4500 1400 W DC Triple Input SP Power Supply requires a minimum draw from the system that it is installed in. Table 1-11 shows Catalyst 4500 Series Switches Installation Guide 1-40 78-14409-08...
  • Page 59 1.33A 0.6A – – – 1.33A 0.6A Mode 3 – – – 2.66A 0.6A – – – 2.66A 0.6A Mode 4 – – – 2.66A 0.6A Mode 5 – – – 0.6A Catalyst 4500 Series Switches Installation Guide 1-41 78-14409-08...
  • Page 60 Input 2 Input 3 Load Load Dual Redundant Operation Mode 1 2.66A 1.2A Mode 2 2.66A 1.2A 2.66A 1.2A Mode 3 5.32A 1.2A 5.32A 1.2A Mode 4 5.32A 1.2A Mode 5 1.2A Catalyst 4500 Series Switches Installation Guide 1-42 78-14409-08...
  • Page 61: System Architecture

    System Architecture System Architecture This section describes the interaction between the various system components of Catalyst 4500 series switches. A Catalyst 4503 only is shown in the examples. Power Flow Figure 1-21 shows power ingress and flow through the system.
  • Page 62: Power Over Ethernet

    (UPS) backup. All new Cisco Catalyst PoE line cards can support 15.4 W of power per port simultaneously. Not only do the cards support the IEEE standard, including the...
  • Page 63 PoE Line Cards The Cisco Catalyst 4500 series offers line cards, power supplies, and accessories required to deploy and operate a standards-based PoE internetwork. PoE provides –48 V DC power over standard Category 5 unshielded twisted-pair (UTP) cable up to 100 meters when an IEEE 802.3af-compliant or Cisco pre-standard powered...
  • Page 64 All available Cisco Catalyst 4500 Series power supplies can be used for data-only deployments, which typically require just a few hundred watts. For deployments that dictate support for PoE power, Cisco offers several options.
  • Page 65 Product Overview System Architecture 4200 W of redundant data and PoE are required for a Cisco Catalyst 4500 Series chassis in an AC-powered environment, Cisco offers an external AC power shelf that houses two 2500 W AC power supplies. When two power shelves are combined, they can produce 7500 W—the remaining 2500 W supply can be used...
  • Page 66: Management Flow

    System Architecture Catalyst 4503 with a single 15A circuit. Likewise, it is possible to deploy a fully populated Cisco Catalyst 4510R with two 20A and one 15A circuits rather than a single 60A connection, which often requires rack rewiring. Management Flow Figure 1-22 shows management and status information flow through the system.
  • Page 67: Switching Traffic Flow

    CiscoWorks, which can manage critical network characteristics such as • availability, responsiveness, resilience, and security. Cisco NetFlow Services. The Cisco NetFlow Services Card for the • Supervisor Engine IV and V support statistics capture in hardware for flow-based and VLAN-based statistics monitoring. This data can be...
  • Page 68 Gigabit Ethernet connection to the internal switch fabric. For each group of ports, frames received are buffered and sent to the common Gigabit Catalyst 4500 Series Switches Installation Guide 1-50 78-14409-08...
  • Page 69 The amount of over-subscription can be controlled by varying the number of ports used at 1000 Mbps. All ports can use Cisco Gigabit EtherChannel technology or IEEE 802.3ad for high-speed interconnection applications. All over-subscribed ports use the standard IEEE 802.1x flow control (PAUSE frame) mechanism to control Gigabit Ethernet host traffic.
  • Page 70 Chapter 1 Product Overview System Architecture Catalyst 4500 Series Switches Installation Guide 1-52 78-14409-08...
  • Page 71: Chapter 2 Preparing For Installation

    Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024 Class 1 laser product. Statement 1008 Warning Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 72: Electrostatic Discharge

    ESD events of up to 2000 V. The design for the common mode event is based on the expectation that the discharge is delivered to all pins of a port at once. Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 73: Preventing Electrostatic Discharge Damage

    When installing a component, use any available ejector levers or captive • installation screws toproperly seat the bus connectors in the backplane or midplane. These devices prevent accidentalremoval, provide proper grounding for the system, and help to ensure that bus connectors areproperly seated. Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 74: Site Power Requirements And Heat Dissipation

    Site Power Requirements and Heat Dissipation This section provides module power requirements and heat dissipation specifications for the Catalyst 4500 series switches. You should verify site power before you install the switch. For more information about power management and planning, refer to the “Environmental Monitoring and Power Management”...
  • Page 75: Power Connection Guidelines For Ac-Powered Systems

    Power Connection Guidelines for AC-Powered Systems Power Connection Guidelines for AC-Powered Systems This section provides guidelines for connecting the Catalyst 4500 series switch AC power supplies to the site power source. Basic guidelines include the following: Make sure each chassis power supply has its own dedicated branch circuit.
  • Page 76 AC-input power cord options, specifications, • and Cisco part numbers, and shows the different styles of 2800 W AC-input power cord wall plugs that are available for North America and international locations as well as the appliance coupler that is attached to the other end of the 2800 W power supply power cord.
  • Page 77 Australia, CAB-A3112-C19-AUS= 14 ft (4.3 m) 250 VAC, 15 A SAA/3, New Zealand (was CAB-7513ACA=) AS/NZZS 3112-1993 Europe (except CAB-CEE77-C19-EU= 14 ft (4.3 m) 250 VAC, 16 A CEE 7/7 Italy) (was CAB-7513ACE=) Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 78 200–240 VAC operation North America CAB-AC-2800W-6-20 13.2 ft 250 VAC, 16 A NEMA 6-20 (non-locking) (4.0 m) non-locking 200–240 VAC operation Europe CAB-AC-2800W-EU= 13.2 ft 250 VAC, 16 A CEE 7/7 (4.0 m) Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 79 200–240 VAC operation North America CAB-AC-2800W-6-20 13.2 ft 250 VAC, 16 A NEMA 6-20 (non-locking) (4.0 m) non-locking 200–240 VAC operation Europe CAB-AC-2800W-EU= 13.2 ft 250 VAC, 16 A CEE 7/7 (4.0 m) Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 80 14 ft (4.2 m) 250 VAC, 20 A NEMA L6-20 (locking) 200–240 VAC operation North America CAB-US620P-C19-US 13.2 ft 250 VAC, 20 A NEMA 6-20 (non-locking) (4.02 m) non-locking 200–240 VAC operation Catalyst 4500 Series Switches Installation Guide 2-10 78-14409-08...
  • Page 81 14 ft (4.3 m) 250 VAC, 10 A IRAM 2073 (was CAB-7513ACR=) Italy CAB-C2316-C19-IT 14 ft (4.3 m) 250 VAC, 16 A CEI 23-16 United CAB-BS1363-C19-UK 14 ft (4.3 m) 250 VAC, 15 A BS 1363 Kingdom Catalyst 4500 Series Switches Installation Guide 2-11 78-14409-08...
  • Page 82 AC-Input Power Cord Options (continued) Locale Part Number Length Plug Rating Plug Type Israeli CAB-S132-C19-ISRL 14 ft (4.3 m) 250 VAC, 16 A SI32 UPS 220V CAB-C19-CBN 9 ft (2.74 m) 250 VAC, 20 A IEC-60320-C20 Catalyst 4500 Series Switches Installation Guide 2-12 78-14409-08...
  • Page 83: Power Connection Guidelines For Dc-Powered Systems

    Power Connection Guidelines for DC-Powered Systems This section provides the basic guidelines for connecting the Catalyst 4500 series switch DC-input power supplies to the site power source or AC power shelf: All power connection wiring should conform to local and national codes.
  • Page 84: Calculating Dc Input Current

    10 X 6.3 W = 63 W for inline devices. • 6.3 Watts is correct for a Cisco IP phone. Wattage consumption will depend on the inline device used. Find the DC input power using the DC output power.
  • Page 85: Ventilation

    Allow at least one foot of clearance for both intake and exhaust air flow, and keep cover plates on unused power supply bays and switching module slots to ensure the air in the chassis flows as designed. Catalyst 4500 Series Switches Installation Guide 2-15 78-14409-08...
  • Page 86: Calculating System Heat Dissipation

    Second example (same system but this time with one IEEE class 3 device): Components Output Power 1 - Catalyst 4506 with fans 50 W 1 - Supervisor Engine IV 145 W 1 - WS-X4248-RJ45V with no phones 72 W Catalyst 4500 Series Switches Installation Guide 2-16 78-14409-08...
  • Page 87: Site-Planning Checklist

    WS-X4248-RJ45V DC-DC converter’s efficiency (89%). Site-Planning Checklist Table 2-2 lists the site-planning activities that you should complete before you install a Catalyst 4500 series switch. Completing each activity helps to ensure a successful switch installation. Table 2-2 Site-Planning Checklist Task No.
  • Page 88 Cable and interface equipment evaluation: • Cable type Connector type • Cable distance limitations • Interface equipment (transceivers) • EMI evaluation: Distance limitations for signaling • Site wiring • RFI levels • Catalyst 4500 Series Switches Installation Guide 2-18 78-14409-08...
  • Page 89: Chapter 3 Installing The Switch In A Rack

    To prevent personal injury or damage to the chassis, never attempt to lift or tilt Warning the chassis using the handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to support the weight of the unit. Statement 1032 Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 90 When populating empty chassis slots, start filling the upper slots first and work Note down to the bottom slots. This chapter describes how to install Catalyst 4500 series switches in a rack. For first-time installations, perform the procedures in the following sections in the order listed: Checking the Shipping Container Contents, page 3-3 •...
  • Page 91: Checking The Shipping Container Contents

    For information on installing the supervisor engine and switching modules and Note verifying switch operation, refer to the Catalyst 4500 Series Module Installation Guide. For information on configuring the switching modules, refer to the software configuration guide for your switch and software release.
  • Page 92: Rack-Mounting The Switch

    Antistatic mat or antistatic foam in case you need to remove switching • modules to troubleshoot the installation Rack-mount kit • Tape measure • Level • Your own electrostatic discharge (ESD) grounding strap or the disposable • ESD strap included with the system Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 93: Rack-Mounting Catalyst 4500 Series Switches

    If the rack is provided with stabilizing devices, install the stabilizers before Statement 1006 mounting or servicing the unit in the rack. Follow these steps to install a Catalyst 4500 series switch in a rack: Prepare for installation as follows: Step 1 Place the chassis on the floor or on a sturdy table as close as possible to the rack.
  • Page 94 (three screws per side) provided in the rack-mount kit. Figure 3-1 for the Catalyst 4503 switch, Figure 3-2 for the Catalyst 4506 switch, or Figure 3-3 for the Catalyst 4507R switch, or Figure 3-4 for the Catalyst 4510R switch. Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 95 Chapter 3 Installing the Switch in a Rack Rack-Mounting the Switch Figure 3-1 L Brackets on the Front Edge of the Catalyst 4503 Switch 45 06 Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 96 Chapter 3 Installing the Switch in a Rack Rack-Mounting the Switch Figure 3-2 L Brackets on the Front Edge of the Catalyst 4506 Switch Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 97 -RJ 45 10/10 0BAS E-TX ETHE RNE MUL TI-SP ST AT GIGA BIT ETHE RNE SWIT CHIN G MOD 10/10 0BAS E-TX ETHE RNE MUL TI-SP GIGA BIT ETHE RNE SWIT CHIN G MOD Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 98 LEDs. Figure 3-5 for the Catalyst 4503 switch, Figure 3-6 for the Catalyst 4506 switch, Figure 3-7 for the Catalyst 4507R switch, or Figure 3-8 for the Catalyst 4510R switch. Catalyst 4500 Series Switches Installation Guide 3-10 78-14409-08...
  • Page 99 Chapter 3 Installing the Switch in a Rack Rack-Mounting the Switch Figure 3-5 Attaching the Cable Guide to the Catalyst 4503 Switch 45 06 Catalyst 4500 Series Switches Installation Guide 3-11 78-14409-08...
  • Page 100 Chapter 3 Installing the Switch in a Rack Rack-Mounting the Switch Figure 3-6 Attaching the Cable Guide to the Catalyst 4506 Switch Catalyst 4500 Series Switches Installation Guide 3-12 78-14409-08...
  • Page 101 10/10 0BAS E-TX ETHE RNE MUL TI-SP ST AT GIGA BIT ETHE RNE SWIT CHIN G MOD 10/10 0BAS E-TX ETHE RNE MUL TI-SP GIGA BIT ETHE RNE SWIT CHIN G MOD Catalyst 4500 Series Switches Installation Guide 3-13 78-14409-08...
  • Page 102 Catalyst 4507R switch in a rack. Figure 3-12 to see how to install the Catalyst 4510R switch in a rack. Align the mounting holes in the L bracket with the mounting holes in the equipment rack. Catalyst 4500 Series Switches Installation Guide 3-14 78-14409-08...
  • Page 103 L bracket and into the threaded holes in the mounting post. Use a tape measure and level to ensure that the chassis is installed straight and level. Figure 3-9 Installing a Catalyst 4503 Switch in the Rack 45 06 Catalyst 4500 Series Switches Installation Guide 3-15 78-14409-08...
  • Page 104 Chapter 3 Installing the Switch in a Rack Rack-Mounting the Switch Figure 3-10 Installing a Catalyst 4506 Switch in the Rack Catalyst 4500 Series Switches Installation Guide 3-16 78-14409-08...
  • Page 105 10/10 0BAS E-TX ETHE RNE ST AT MUL TI-SP GIGA BIT SWIT CHIN ETHE RNE G MOD 10/10 0BAS E-TX ETHE RNE MUL TI-SP GIGA BIT ETHE RNE SWIT CHIN G MOD Catalyst 4500 Series Switches Installation Guide 3-17 78-14409-08...
  • Page 106 Make sure that the ejector levers are completely closed and the supervisor engine Step 4 and switching modules are installed securely. Tighten any loose captive installation screws on the supervisor engine and the Step 5 switching module. Catalyst 4500 Series Switches Installation Guide 3-18 78-14409-08...
  • Page 107: System Ground Connection Guidelines

    System Ground Connection Guidelines A grounding pad with two system (earth) grounding holes is provided in an enclosure near the left power supply on the Catalyst 4500 series switches. See Figure 3-13 for the location of the grounding holes on the Catalyst 4503 switch,...
  • Page 108 Chapter 3 Installing the Switch in a Rack System Ground Connection Guidelines Figure 3-14 Catalyst 4506 Grounding Holes Grounding holes (2) 45 06 Catalyst 4500 Series Switches Installation Guide 3-20 78-14409-08...
  • Page 109 10/10 0BAS E-TX ETHE RNET MUL TI-SP STA TU GIGA BIT ETHE RNET SWIT CHIN G MOD 10/10 0BAS E-TX ETHE RNET MUL TI-SP GIGA BIT SWIT CHIN ETHE RNET G MOD Catalyst 4500 Series Switches Installation Guide 3-21 78-14409-08...
  • Page 110 10/10 0BAS ETHE RNE E-TX ST AT MUL TI-SP GIGA BIT ETHE RNE SWIT CHIN G MOD 10/10 0BAS E-TX ETHE RNE MUL TI-SP GIGA BIT SWIT CHIN ETHE RNE G MOD Catalyst 4500 Series Switches Installation Guide 3-22 78-14409-08...
  • Page 111: Parts And Required Tools

    Some parts and required tools described in this section are not available from Note Cisco Systems. The grounding lug and associated screws are included with the accessory kit. To make an adequate grounding connection, you will need the following parts and tools: Grounding lug—The grounding lug has two #10 AWG holes spaced 0.63 in...
  • Page 112: Connecting System Ground And Power

    System Ground Connection Guidelines Connecting System Ground and Power This section describes how to connect the Catalyst 4500 series switches to earth ground. The system ground connection is required if FXS modules are installed or if this equipment is installed in a US or European Central Office.You must complete this procedure before connecting system power or turning on your switch.
  • Page 113 M4 screws through the holes in the grounding lug and grounding pad (Figure 3-15 Figure 3-17). Ensure that the grounding lug and the attached wire will not interfere with other switch hardware or rack equipment. Catalyst 4500 Series Switches Installation Guide 3-25 78-14409-08...
  • Page 114 If the situation persists, you need to disconnect the RJ-45-to-RJ-45 rollover cable and replace it with a shielded cable (Cisco p/n 72-1499-01). The shielded cable eliminates the EMI noise causing the meaningless characters.
  • Page 115: Chapter 4 Removing And Replacing Frus

    Statement 43 Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 116: Removing And Replacing The Power Supply

    Removing and Replacing FRUs Removing and Replacing the Power Supply This chapter tells you how to remove and replace Catalyst 4500 series field-replaceable units (FRUs). The information is presented in these sections: Removing and Replacing the Power Supply, page 4-2 •...
  • Page 117 IN P U T P O E E N A B L AC input 2 on switch IN P U T AC input 2 receptacle 10 0- 12 0V - 12 A 50 /6 0H Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 118 Removing and Replacing the Power Supply Figure 4-3 DC-Input Power Supply Main power switch In-line power switch Captive screw Serial communication connector Captive screw Terminal block Figure 4-4 1400 W DC Triple-input Power Supply Captive screws Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 119: Required Tools

    There are two on/off switches on a 4200 W AC power supply, one for each Note input. Loosen the side-clamp screw on the right side of the power cord plug (see Step 2 Figure 4-6). Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 120 Loosening the Side-Clamp Screw Disconnect the power cord from the power supply being removed. Step 3 Loosen the two captive screws (see Figure 4-7). Step 4 Figure 4-7 Loosening the Captive Screws Captive screws Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 121 If the power supply bay is to remain empty, install a blank power supply filler Step 7 plate over the opening. Secure the filler plate with the two mounting screws and tighten them with a screwdriver. Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 122: Installing An Ac-Input Power Supply

    Before you connect the power supply to a power source, ensure that all site power and grounding requirements described in the Site Preparation and Safety Guide have been met. Plug the power cord into the power supply (see Figure 4-9). Step 9 Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 123 Step 11 Press the power switch down to the on (|) position (see Figure 4-10). Figure 4-10 Powering On the Power Supply Power switch Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 124 Step 13 the show system command (Catalyst Operating System) or the show power command (Cisco IOS). For more information on this command, refer to the command reference publication for your switch. If the LEDs or the show system command (Catalyst Operating System) or the...
  • Page 125: Removing A Dc-Input Power Supply

    Loosen the screw on the terminal block cover and remove it from the terminal Step 4 block (see Figure 4-11 Figure 4-12). The triple-input power supply has two screws on the cover. Catalyst 4500 Series Switches Installation Guide 4-11 78-14409-08...
  • Page 126 DC Triple-input Power Supply Captive screw Output Fail LED Plus (+) Fan OK LED Minus (-) Input OK 1, 2, 3 LEDs Captive screw Power switch 1, 2, 3 Terminal block Ground lugs Catalyst 4500 Series Switches Installation Guide 4-12 78-14409-08...
  • Page 127 DC-input wires Negative Positive Ground Grounding lug Grounding lug nuts Figure 4-14 Connecting the DC-Input Wires (Triple-input Power Supply) DC-input wires Negative Positive Ground Grounding lugs (2) Grounding lug nut Catalyst 4500 Series Switches Installation Guide 4-13 78-14409-08...
  • Page 128 Loosening the Captive Screws Captive screws Step 7 Grasp the power supply handle with one hand. Place your other hand underneath as you slowly pull the power supply out of the bay (see Figure 4-16). Catalyst 4500 Series Switches Installation Guide 4-14 78-14409-08...
  • Page 129 (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029 Catalyst 4500 Series Switches Installation Guide 4-15 78-14409-08...
  • Page 130: Installing A Dc-Input Power Supply

    When stranded wiring is required, use approved wiring terminations, such as Warning closed-loop or spade-type with upturned lugs. These terminations should be the appropriate size for the wires and should clamp both the insulation and conductor. Statement 1002 Catalyst 4500 Series Switches Installation Guide 4-16 78-14409-08...
  • Page 131 DC power source. In the event of a power source failure, if the second source is still available, it can maintain maximum overcurrent protection for each power connection. Catalyst 4500 Series Switches Installation Guide 4-17 78-14409-08...
  • Page 132: Removing And Replacing The Chassis Fan Assembly

    Step 9 the show system command (Catalyst Operating System) or the show power command (Cisco IOS). For more information on these commands, refer to the command reference publication for your switch and software. If the LEDs or the show system command (Catalyst Operating System) or the...
  • Page 133 Chapter 4 Removing and Replacing FRUs Removing and Replacing the Chassis Fan Assembly Figure 4-17 Catalyst 4503 System Fan Assembly Fan assembly Captive installation screws Catalyst 4500 Series Switches Installation Guide 4-19 78-14409-08...
  • Page 134 Chapter 4 Removing and Replacing FRUs Removing and Replacing the Chassis Fan Assembly Figure 4-18 Catalyst 4506 System Fan Assembly Fan assembly Captive installation screws Catalyst 4500 Series Switches Installation Guide 4-20 78-14409-08...
  • Page 135 ETHE RNE ST AT MUL TI-SP GIGA BIT ETHE RNE SWIT CHIN G MOD 10/10 0BAS E-TX ETHE RNE MUL TI-SP GIGA BIT ETHE RNE Captive installation SWIT CHIN G MOD screws Catalyst 4500 Series Switches Installation Guide 4-21 78-14409-08...
  • Page 136: Required Tools

    G MOD 10/10 0BAS E-TX ETHE RNE MUL TI-SP GIGA BIT ETHE RNE SWIT CHIN G MOD Captive installation screws Required Tools You will need a Phillips screwdriver for the following two procedures. Catalyst 4500 Series Switches Installation Guide 4-22 78-14409-08...
  • Page 137: Removing The Fan Assembly

    Slide the fan assembly into the chassis until the two captive installation screws Step 3 make contact with the chassis. Using a screwdriver, tighten the two captive installation screws by turning them Step 4 clockwise. Catalyst 4500 Series Switches Installation Guide 4-23 78-14409-08...
  • Page 138: Verifying The Installation

    If after several attempts the fans do not operate, or if you experience trouble with Step 3 the installation (for instance, if the captive installation screws do not align with the chassis holes), contact the Cisco TAC for assistance. Replacing Backplane Modules on a Catalyst 4507R or 4510R Switch There are 5 redundancy modules (also called mux buffers) and 1 clock module on a Catalyst 4507R chassis backplane.
  • Page 139 Keep a record of switching moduleand their slots, so that you can put them back Note correctly. Generic switching module replacement procedures are documented at: Note http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/hw_doc/gmdcf_nt .htm#wp21932 Figure 4-21 shows the front view of the backplane with supervisors and switching modules removed. Catalyst 4500 Series Switches Installation Guide 4-25 78-14409-08...
  • Page 140 Chapter 4 Removing and Replacing FRUs Replacing Backplane Modules on a Catalyst 4507R or 4510R Switch Figure 4-21 Catalyst 4507R Backplane Clock module Mux buffers Catalyst 4500 Series Switches Installation Guide 4-26 78-14409-08...
  • Page 141 Finding the Seating Levers To release the module from its connector, pull the levers outward with your Step 6 fingernails. The module will pop out slightly. (See Figure 4-23.) Figure 4-23 Releasing the Module Catalyst 4500 Series Switches Installation Guide 4-27 78-14409-08...
  • Page 142 Put the replacement module in at roughly a 30 degree angle, and gently push the Step 8 module down. Make sure you apply force evenly on the left and right. (See Figure 4-25.) Figure 4-25 Seating the Replacement Module Catalyst 4500 Series Switches Installation Guide 4-28 78-14409-08...
  • Page 143 If you are installing a clock module, secure the module to the backplane using the Step 12 screws from the earlier removal. Replace the supervisor engines and switching modules to their previous slots. Step 13 Restore power to the switch. Step 14 Catalyst 4500 Series Switches Installation Guide 4-29 78-14409-08...
  • Page 144: Verify The New Modules

    3, 4 and 7. You need to reinsert and reseat the modules in those slots. If the switch has already started up, you may also verify the correct function of the new modules with the show logging command. Catalyst 4500 Series Switches Installation Guide 4-30 78-14409-08...
  • Page 145 Troubleshooting the Fan Assembly, page 5-8 • Troubleshooting Backplane Modules, page 5-9 • Troubleshooting Switching Modules, page 5-10 • Troubleshooting Supervisor Engines, page 5-13 • Contacting the Cisco Technical Assistance Center, page 5-16 • Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 146: Chapter 5 Troubleshooting

    When the initial system boot is complete, verify the following: That the power supplies are supplying power to the system • The LEDs should be green. Use the show environment Cisco IOS command to view power supply activity. That the system fan assembly is operating •...
  • Page 147: Problem Solving To The System Component Level

    For more informations, see the “Troubleshooting Switching Modules” section on page 5-10. If you determine that the switching module is not operating, contact Cisco TAC as described in the “Contacting the Cisco Technical Assistance Center” section on page 5-16.
  • Page 148: Using Leds To Identify Startup Problems

    If you have problems after the switch is on, refer to the configuration procedures in the software configuration guide for your switch. After you connect the power cords to your Catalyst 4500 series switch, follow these steps to determine whether your system is operating properly:...
  • Page 149 If an LED labeled STATUS is red or orange, try reseating the switching module or supervisor engine and restarting the switch. If the problem persists, contact Cisco TAC. See the “Contacting the Cisco Technical Assistance Center” section on page 5-16.
  • Page 150: Troubleshooting The Power Supply

    Check that the LED labeled GOOD is on for the additional power supply. Check Step 8 that the LED labeled FAIL is off. If the LEDs are not on, repeat the previous procedure to troubleshoot the second Step 9 power supply. Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 151: Troubleshooting The Power Supply

    Troubleshooting the Power Supply If you are unable to resolve the problem, or if you determine that either a power supply or backplane connector is faulty, contact the Cisco Technical Assistance Center (TAC) for instructions. Troubleshooting Power Problems using Cisco IOS Check for system messages related to the power supply, and refer to the system message guide for your software release.
  • Page 152: Troubleshooting The Fan Assembly

    If you mix power supplies in a Catalyst 4500 series chassis, the switch detects the type of power supply in power supply bay 1 (PS1) and...
  • Page 153: Troubleshooting Backplane Modules

    Restart the system. Step 7 Verify that all fans are operating. You should hear the fans at system start. Step 8 If the system is still detecting a fan assembly failure, contact the Cisco TAC for Step 9 assistance. Troubleshooting Backplane Modules...
  • Page 154: Troubleshooting Switching Modules

    CPU Utilization LEDs are flashing green or off. • If you observe these conditions, contact the Cisco TAC for assistance in ordering replacement redundancy modules and a clock. Troubleshooting Switching Modules Each switching module has one LED labeled STATUS that provides information about the module and one numbered LED labeled LINK for each port on the module.
  • Page 155 No signal is detected. 1. Used on the WS-X4232-L3 Ethernet routing module. 2. LEDs labeled 1 through the number of ports on the switching module are the individual port link LEDs. Catalyst 4500 Series Switches Installation Guide 5-11 78-14409-08...
  • Page 156: Troubleshooting Switching Modules Using Cisco Ios

    Not all software versions support all switching modules. If you are having trouble with a module, refer to the software release notes to be sure that it is supported by your software. Catalyst 4500 Series Switches Installation Guide 5-12 78-14409-08...
  • Page 157: Troubleshooting Supervisor Engines

    Green The link is operational. Orange The link is disabled by user. Flashing orange The power-on self-test indicates a faulty port. No signal is detected or there is a link configuration failure. Catalyst 4500 Series Switches Installation Guide 5-13 78-14409-08...
  • Page 158: Troubleshooting Supervisor Engines Using Cisco Ios

    Troubleshooting Supervisor Engines Using Cisco IOS Connect a terminal to the console port, and look for any of the following system messages: C4K_CHASSIS-3-LINECARDMUXBUFFERTOSUPALIGNMENTWRON C4K_SUPERVISOR-3-MUXBUFFERREADSUPERVISORSELECTIONF AILED C4K_CHASSIS-3-TEMPERATURESENSORREADFAILED C4K_HW-3-X2IDENTIFICATIONFAILURE C4K_HW-3-X2OUIREGREADFAILURE C4K_HWACLMAN-4-CLASSIFCAMPARITYERROR C4K_HWACLMAN-4-CLASSIFCAMREPLYPARITYERROR C4K_HWACLMAN-4-CLASSIFCAMREQPARITYERROR C4K_HWNETFLOWMAN-3-NETFLOWSTOPPED C4K_HWNETFLOWMAN-4-FATALERRORINTERRUPTSEEN C4K_HWNETFLOWMAN-4-NONFATALPARITYERRORINTERRUPTSE C4K_IOSMODPORTMAN-4-NFLABSENT C4K_IOSMODPORTMAN-4-NFLIDPROMINVALID C4K_IOSMODPORTMAN-4-NFLMISMATCH Catalyst 4500 Series Switches Installation Guide 5-14 78-14409-08...
  • Page 159 Problems with redundant supervisor systems are often due to mismatched active and standby supervisor engines. Redundancy requires that both supervisor engines be the same model and running the same Cisco IOS release. If one supervisor has a NetFlow service card, the other must as well.
  • Page 160: Contacting The Cisco Technical Assistance Center

    If you are unable to solve a startup problem after using the troubleshooting suggestions in this chapter, contact a Cisco TAC representative for assistance and further instructions. Before you call, have the following information ready to help the Cisco TAC assist you as quickly as possible: Date you received the switch •...
  • Page 161: Serial Numbers

    “Obtaining Documentation and Submitting a Service Request” section on page xvii for more information about contacting the TAC. Serial Numbers When you contact Cisco Technical Assistance, have the serial number of your switch available. Refer to Figure 5-3 to locate the serial number on your switch.
  • Page 162 Chapter 5 Troubleshooting Contacting the Cisco Technical Assistance Center Figure 5-4 Catalyst 4506 Serial Number Location SN: AAANNNNXXXX 45 06 Catalyst 4500 Series Switches Installation Guide 5-18 78-14409-08...
  • Page 163 10/10 0BAS E-TX ETHE RNE MUL TI-SP ST AT GIGA BIT ETHE RNE SWIT CHIN G MOD 10/10 0BAS E-TX ETHE RNE MUL TI-SP GIGA BIT ETHE RNE SWIT CHIN G MOD Catalyst 4500 Series Switches Installation Guide 5-19 78-14409-08...
  • Page 164 E-TX ETHE RNET STA TUS MULT I-SPE ED GIGA BIT ETHE RNET SWIT CHIN G MOD 10/10 0BAS E-TX ETHE RNET MULT I-SPE ED GIGA BIT ETHE RNET SWIT CHIN G MOD Catalyst 4500 Series Switches Installation Guide 5-20 78-14409-08...
  • Page 165: Appendix

    A P P E N D I X Specifications Cable and technical specifications for Catalyst 4500 series switches are provided in the following sections: • Catalyst 4503 Switch Specifications, page A-2 Catalyst 4506 Switch Specifications, page A-3 • Catalyst 4507R Switch Specifications, page A-5 •...
  • Page 166: Catalyst 4503 Switch Specifications

    Backplane 24 Gbps full duplex backplane 4 Gbps Uplinks Port density 116 ports when using a Catalyst 4500 Series Supervisor Engine II-Plus TS, 96 ports with other supervisor engines Inline power integrated support, 820 W per switching module Physical Characteristics Dimensions (H x W x D) 12.25 x 17.31 x 12.50 in.
  • Page 167: Catalyst 4506 Switch Specifications

    Humidity (RH), ambient (noncondensing): operating 10 to 90% nonoperating and storage 5 to 95% Altitude: operating –500 to 6500 ft (–150 to 2000 m) nonoperating –1000 to 30,000 ft (–300 to 9150 m) Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 168: Catalyst 4506 Switch Specifications

    Right to left Power supply Front to back Power PoE supplied –48 VDC Power to Modules and fans 12 VDC Power to backplane components 3.3 VDC Redundancy Supervisor engine Power supply 1 + 1 Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 169: Catalyst 4507R Switch Specifications

    Minimum weight: 44.25 lb (20.1 kg) Maximum weight: 100 lb (45.4 kg) Chassis and backplane: 40.0 lb (18.1 kg) Fan tray: 4.2 lb ( 1.9 kg) Airflow Switch Right to left Power supply Front to back Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 170 (C4K-SLOT-CVR-E) in slot 1 rather than a blank faceplate (C4K-SLOT-CVR) . A blank faceplate covering the slot 1 opening does not direct sufficient airflow to adequately cool the Supervisor Engine 6-E or the Supervisor Engine 6L-E. Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 171: Catalyst 4510R Switch Specifications

    24.35 x 17.31 x 12.50 in. (61.84 x 43.97 x 31.70 cm) • 14 RU • Weight Minimum weight: 51.5 lb (23.4 kg) Maximum weight: 108 lb (49.8 kg) Chassis and backplane: 45.5 lb (20.6 kg) Fan tray: 6.0 lb (2.7 kg) Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 172 (C4K-SLOT-CVR-E) in slot 1 rather than a blank faceplate (C4K-SLOT-CVR) . A blank faceplate covering the slot 1 opening does not direct sufficient airflow to adequately cool the Supervisor Engine 6-E or the Supervisor Engine 6L-E. Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 173: Catalyst 4500 Series Power Supplies

    A-12 list the specifications for the Catalyst 4500 series power supplies. All Catalyst 4500 series switch AC-input power supplies require single-phase Note source AC. The source AC can be out of phase between multiple power supplies or multiple AC-power plugs on the same power supply because all AC power supply inputs are isolated.
  • Page 174 943 BTUs/hr 1. A Catalyst 4503 with a Catalyst 4500 series Supervisor Engine II-Plus TS and a 1000W power supply will be able to provide 158.4 W of Power over Ethernet to ports on the supervisor engine. Switching modules in other slots will not be able to provide PoE.
  • Page 175 100 to 240 VAC (±10% for full range) AC-input current 16 A @ 100 VAC, 7 A @ 240 VAC AC-input frequency 50/60 Hz (nominal) (±3 Hz for full range) Maximum KVA rating 1.76 KVA Catalyst 4500 Series Switches Installation Guide A-11 78-14409-08...
  • Page 176 20 ms minimum 1. A Catalyst 4503 with a Catalyst 4500 series Supervisor Engine II-Plus TS and a 1400W AC power supply provides 158.4 W of PoE to ports on the supervisor engine. Switching modules in other slots will not be able to provide PoE.
  • Page 177 DC-input current Data only: 31 A @ –60 VDC Data and inline devices: 180 A maximum @ –48 VDC input The input power is configurable in the CLI. The Cisco Note IOS command is power dc input. The Catalyst Operating Sysytem command is set power DC input.
  • Page 178 Max input is 1080 W / 0.75 = 1440 W Current draw at –40.5 V (min voltage) 35.6 A Current draw at –72 V (max voltage) 20 A Max heat dissipation 1440 W 4910 BTUs Catalyst 4500 Series Switches Installation Guide A-14 78-14409-08...
  • Page 179 10 to 12 AWG size copper wire. The connector the barrier spacing is 0.378 in (9.6 mm), and the screw size is 8-32. Output holdup time 8 ms Max heat dissipation 1269 BTUs/hr Catalyst 4500 Series Switches Installation Guide A-15 78-14409-08...
  • Page 180 33.75 A total / # of modules = A per module Current draw at –72 V (max voltage) 19 A total / # of modules = A per module Max heat dissipation 1367 W 4665 BTUs Catalyst 4500 Series Switches Installation Guide A-16 78-14409-08...
  • Page 181 1750 W 1900 W 2 and 3 1400 W 1450 W 1750 W 1820 W 2130 W 1 and 2 and 3 1700 W 1750 W 1900 W 2130 W 2450 W Catalyst 4500 Series Switches Installation Guide A-17 78-14409-08...
  • Page 182 2473 W maximum in combined mode (Data) 1400 W maximum each in redundant mode (PoE) 2333 W maximum in combined mode (PoE) Max heat dissipation 2387 BTUs/hr. Output holdup time 20 ms minimum Catalyst 4500 Series Switches Installation Guide A-18 78-14409-08...
  • Page 183 20 ms minimum The 4200 W AC power supply should not be used in mixed-voltage Note configurations. All the inputs in a chassis must be at the same voltage (110 VAC or 220 VAC). Catalyst 4500 Series Switches Installation Guide A-19 78-14409-08...
  • Page 184 110+110, other side 110 1800 2000 2730 Both sides at 110+110 2200 3100 3800 Both sides at 220 2200 3100 3800 220+220, other side 220 2200 4700 5500 Both sides at 220+220 2200 6200 7600 Catalyst 4500 Series Switches Installation Guide A-20 78-14409-08...
  • Page 185: Appendix

    A P P E N D I X Repacking a Switch If you need to return your Catalyst 4500 series switch to the factory, use the instructions in this appendix to repack your switch in preparation for shipping. To repack the switch using the original packaging material, follow these steps: Slide the pieces of the packing foam over the Catalyst 4500 series switch.
  • Page 186 Appendix B Repacking a Switch Figure B-1 Catalyst 4500 Series Switch Packing Material Documentation and accessories Packing foam Packing carton Packing foam Packing foam Catalyst 4500 Series Switches Installation Guide 78-14409-08...
  • Page 187: I N D E X

    2-5, 2-6 power cords (table) Catalyst 4506 switches (table) 2800 W power supplies Catalyst 4507 switches (table) A-5, A-7 power cord plugs direction 1-27 power cords (table) figure 2-9, 2-10 1-29, 1-30 Catalyst 4500 Series Switches Installation Guide IN-1 78-14409-08...
  • Page 188 (figure) 3-14 components power requirements troubleshooting 5-3 to 5-17 repacking connecting specifications system ground 3-18 to 3-25 Catalyst 4506 switches conventions attaching cable guides (figure) 3-11 warnings xiii attaching L brackets (figure) Catalyst 4500 Series Switches Installation Guide IN-2 78-14409-08...
  • Page 189 1-35 documentation removing 4-23 conventions replacing 4-22 troubleshooting verifying installation 4-24 FAN OK LED electrostatic discharge checking 4-10 see ESD description 1-34 environmental monitoring Fast Ethernet power supplies 1-35 See 100BASE-T Catalyst 4500 Series Switches Installation Guide IN-3 78-14409-08...
  • Page 190 4-18 to 4-24 ground wire installing switches in racks 3-3 to 3-25 figure 4-13 labels, chassis serial number heat dissipation See serial numbers description (table) L brackets supervisor engines rack-mounting switches switch chassis LEDs Catalyst 4500 Series Switches Installation Guide IN-4 78-14409-08...
  • Page 191 4-24, 5-9 AC-input power supplies DC-input power supplies 4-11 repacking switches replacing OUTPUT FAIL LED AC-input power supplies 4-8 to 4-10 environmental monitoring 1-35 DC-input power supplies 4-16 to 4-18 fan assemblies 4-23 Catalyst 4500 Series Switches Installation Guide IN-5 78-14409-08...
  • Page 192 1-22, 1-23 supervisor engines supervisor engines switching modules Catalyst 4503 switches Catalyst 4506 switches 1-8, 1-12, 1-16 description 1-18 LEDs (table) 1-24 uplink ports slot locations 1-3, 1-7, 1-11, 1-15 description 1-25 Catalyst 4500 Series Switches Installation Guide IN-6 78-14409-08...
  • Page 193 Index UTILIZATION LEDs description (table) 1-24 voltage specifications A-10, A-13 weight Catalyst 4503 switches (table) Catalyst 4506 switches (table) Catalyst 4507 switches (table) A-5, A-6 Catalyst 4500 Series Switches Installation Guide IN-7 78-14409-08...
  • Page 194 Index Catalyst 4500 Series Switches Installation Guide IN-8 78-14409-08...

Table of Contents