Table of Contents
Quick Links
Cordless Driver Drill
Capacities
Steel
Wood
Wood screw
Machine screw
10"
15mm
5 1 m m x 3 5 m m
6 mm
1318'7
119132")
113164' x 1-318")
(15164")
Equipped with Electric Brake
MODEL 6 0 7 5 D
MODEL 6 0 7 5 D W
Wlth Fast Charger
No load speed (FiPMl
Dimensions
Net
IL x
W
x H )
260 mm x 58 mm x 223 mm
weight
High
Low
1 45 kg
-
850
-
300
(10-114'' x 2-114" x 8-25/32")
(3 2 Ibs)
INSTRUCTION MANUAL
1.2
v
SPEC IF I CAT1 0 N S
Model 6075D
1 Hr,
A.C. only 50 Hz
~
60 Hz
D.C. 7.2 V
*
Battery Cartridge 7000
I
Model DC7100 Fast Charger
Voltage
I
Charging time
I
Input
I
output
Table of Contents
Related Manuals for Makita 6075D
Summary of Contents for Makita 6075D
- Page 1 Equipped with Electric Brake MODEL 6 0 7 5 D MODEL 6 0 7 5 D W Wlth Fast Charger INSTRUCTION MANUAL SPEC IF I CAT1 0 N S Model 6075D Capacities No load speed (FiPMl Dimensions IL x x H )
- Page 2 IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
- Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to tool see that keys and adjusting wrenches removed from before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16.
- Page 4 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION To reduce risk of injury, charge only MAKITA Battery 7000. Other types of batteries may burst causing personal injury and damage. or snow.
- Page 5 ADDITIONAL SAFETY RULES CHARGER & BATTERY CARTRIDGE Do not charge Battery Cartridge when temperature is BELOW 10°C ( 5 O O F ) or ABOVE 4OoC ( 1 0 4 O F ) . Do not attempt to use a step-up transformer, an engine generator or DC power receptacle.
- Page 6 Installing or removing battery cartridge Always switch off the tool before insertion removal the battery cartridge. To remove the battery cartridge, pull out tool the set plate and grasp both sides the cartridge while withdrawing it from the tool. To insert the battery cartridge, align the tongue on t h e battery cartridge with the groove in the housing and slip it into place.
- Page 7 Installing or removing driver bit or drill bit CAUTION is removed before tool Always sure that the is switched and the battery cartridge installing or removing the bit. t u r n Hold the ring and the sleeve counter- clockwise to open the chuck jaws. Place f a r will as it...
- Page 8 Speed change change the tool speed, turn the speed Arrow change knob that the arrow of the de- sired speed on the knob is aligned with the reference arrow on the tool body. If the speed change knob does not turn easily, tool switch on the and turn the knob again...
- Page 9 Screwdriving operation Place the point the driver bit screw head and apply pressure t o the tool. Start the tool slowly and then increase the speed gradually. Release the trigger as soon as the clutch cuts in. NOTE : .Make sure that the driver bit is inserted st :raight in the screw head, or the screw and/or bit may be damaged.
- Page 10 Drilling operation Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. Drilling metal To prevent the bit from slipping when starting a hole, make an indentation with a centerpunch and hammer at the point to be drilled.
- Page 11 Always be sure that the is switched and the battery cartridge removed before attempting to perform inspection maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized Factory Service Centers, always using Makita replacement parts.
- Page 12 ACCESSOR I ES CAUTION: with your Makita tool specified in this These accessories attachments are recommended manual. The any other accessories attachments might present a risk injury t o persons. The accessories attachments should be used only in t h e proper and intended manner.
- Page 13 Mar-O7-'89 CORDLESS DRIVER DRILL Model 6075D Note: The switch and other part configurations may differ from country t o country.
- Page 14 MODEL 6075D Mar.-07-69 'Ft $tD I F O M DESCRIPTION DESCRIPTION MACHINE Pan Head Screw M4x22 IWith Washer) Flat Washer 14 Pan Head Screw M4r35 IWith Washer) Ball Bearing 626LLB Housing Set (With Item 441 Flat Washer 6 Guide Plate...
- Page 15 MAKITA LIMITED O N E YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.