Page 1 DCR-TRV8/TRV8E/TRV10/TRV10E RMT-808/809/811/812 SERVICE MANUAL Ver 1.0 1999. 04 US Model Canadian Model DCR-TRV8/TRV10 AEP Model UK Model Australian Model Chinese Model DCR-TRV8E/TRV10E E Model Hong Kong Model DCR-TRV8/TRV8E/TRV10/TRV10E Photo: DCR-TRV10 RMT-811 Tourist Model D300 MECHANISM DCR-TRV10/TRV10E DCR-TRV8/TRV10: NTSC model For MECHANISM ADJUSTMENTS, refer to the “DV MECHANICAL...
Page 2 MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Page 3: Table Of Contents
TABLE OF CONTENTS SERVICE NOTE Superimposing a still picture in a memory stick on a moving picture– M. CHROM/M. LUMI/C. CHROM ······················ 1-27 POWER SUPPLY DURING REPAIRS ····························· 6 Preventing accidental erasure – Image protection ··············· 1-28 TO TAKE OUT A CASSETTE WHEN NOT EJECT Writing a print mark –...
Page 4 • FP-91 (TOP/END SENSOR), FP-92 (TAPE LED), Order of Adjustments ······················································ 5-7 FP-242 (S/T REEL SENSOR) Subjects ··········································································· 5-7 PRINTED WIRING BOARDS ····················· 4-33 1-2. INITIALIZATION OF B, C, D, E, F PAGE DATA ········ 5-8 • VC-217 (MECHANISM CONTROL)(8/11) 1-2-1.
Page 5 3-1-1. Equipment Required ····················································· 5-36 Switch check (1) ···························································· 5-59 3-1-2. Precautions on Adjusting ·············································· 5-37 Switch check (2) ···························································· 5-60 3-1-3. Adjusting Connectors ···················································· 5-38 Record of Use check ······················································ 5-60 3-1-4. Connecting the Equipment ············································ 5-38 3-1-5. Checking the Input Signals REPAIR PARTS LIST (Except AEP/UK model) ··············································...
Page 6: Service Note
SERVICE NOTE POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off so that the unit cannot operate. This following two methods are available to prevent this. Take note of which to use during repairs.
Page 7: Self-Diagnosis Function
SELF-DIAGNOSIS FUNCTION SELF-DIAGNOSIS DISPLAY SELF-DIAGNOSIS FUNCTION When problems occur while the unit is operating, the counter of the When problems occur while the unit is operating, the self-diagnosis viewfinder, LCD screen or LCD window consists of an alphabet function starts working, and displays on the viewfinder, LCD screen or LCD window what to do.
Page 8: Self-Diagnosis Code Table
SELF-DIAGNOSIS CODE TABLE Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Condensation. Remove the cassette, and insert it again after one hour. Video head is dirty. Clean with the optional cleaning cassette. Non-standard battery is used. Use the info LITHIUM battery. LOAD direction.
Page 9: General
DCR-TRV8/TRV8E/TRV10/TRV10E 1. GENERAL This section is extracted from instruction manual. (DCR-TRV8E/TRV10E model)
Page 18 1-10...
Page 19 1-11...
Page 20 1-12...
Page 21 1-13...
Page 22 1-14...
Page 23 1-15...
Page 24 1-16...
Page 25 1-17...
Page 26 1-18...
Page 27 1-19...
Page 28 1-20...
Page 29 1-21...
Page 30 1-22...
Page 31 1-23...
Page 32 1-24...
Page 33 1-25...
Page 34 1-26...
Page 35 1-27...
Page 36 1-28...
Page 37 1-29...
Page 38 1-30...
Page 39 1-31...
Page 40 1-32...
Page 41 1-33...
Page 42 1-34...
Page 43 1-35...
Page 44 1-36...
Page 45 1-37E...
Page 46: Disassembly
DCR-TRV8/TRV8E/TRV10/TRV10E SECTION 2 DISASSEMBLY The following flow chart shows the disassembly procedure. DCR-TRV8/8E/10/10E 2-2. Front panel assembly 2-1. LCD panel (PD-110 board, invertor trans unit) 2-3. Cabinet (L), BT panel assembly 2-11. CK-84 board, Speaker 2-4.EVF 2-12. LCD, Control swith block 2-6.
Page 47: Front Panel Assembly
2-2. FRONT PANEL ASSEMBLY 9 Tapping screw (M1.7 3.5) !¢ Two tapping screws !º SE-94board (M1.7 3.5) CN7307 5P (MA-358 board) 2 Top cabinet assembly !∞ Microphone retainer !¡ Tapping screw (M1.7 3.5) 1 Screw (M1.7) lock ace assembly !™ MA-358 board !§...
Page 48: Evf
2-4. EVF 2 Two screws (M1.7 6) B tight 6 Tilt up the EVF. 8 Tilt down the EVF. 1 Screw (M1.7 2.5) 9 EVF assembly (Remove the assembly while holding it upward.) 5 Two tapping screws (M1.7 4 Flexible retainer sheet 7 Screw (M1.7) lock ace 3 FP-87 flexible board CN5101 27P (DD-123 board)
Page 49: Board, Vc-217 Board
2-6. DD-123 BOARD, VC-217 BOARD 3 DD-123 board 4 FP-92 flexible board CN2501 (VC-217 board) 6 Flexible board 2 Screw (M1.7 2.5) 5 FP-85 flexible board (from drum motor) CN2507 (VC-217 board) CN1810 (VC-217 board) 1 Connector CN3201 3P (DD-123 board) 7 FP-586 flexible board CN2502 (VC-217 board) 8 FP-91 flexible board...
Page 50: Cs Flame Assembly
2-8. CS FLAME ASSEMBLY 3 Zoom cover 2 Screw (M1.7 2.5) 4 Tapping screw (M1.7 3.5) 5 Two tapping screws !¡ FK button (M1.7 3.5) 7 Tapping screw (M1.7 3.5) !™ Screw (M1.7 2.5) 6 Four tapping screws 8 Control switch block (PS4550) (M1.7 3.5) CN64 (FP-85 flexible board)
Page 51 2-10.MS SHASSIS, CONTROL SWITCH BLOCK (PS-4550) Note for installing the operation switch block (PS-4550) 3 Two tapping screws (M1.7 3.5) 4 Control switch block (PS-4550) When installing the operation switch block (PS-4550), align the switch of the area A with the power button on the cabinet (L) side.
Page 52: Lcd, Control Switch Block
2-12.LCD, CONTROL SWITCH BLOCK 3 Slide the panel lock knob backward and open the LCD panel. 8 LCD assembly 6 FP-91 flexible board CN8606 6P (CK-84 board) 5 Harness (PC-112) CN8604 13P (CK-84 board) 7 Two screws (M1.7) lock ace 1 Three tapping screws (M1.7 3.5)
Page 53 2-13.SERVICE POSITION (Mainly for voltage measurement and check) Firstly: Remove the respective parts by referring to "Disassembly 2-2 through 2-4, and 2-6 through 2-9". Then, connect them as shown. Adjustment remote commander (RM-95) JK-170 board Cabinet (L) assembly Lens assembly CPC-8 tarminal board jig (J-6082-388-A) F panel assembly...
Page 54: Circuit Board Location
2-14.CIRCUIT BOARD LOCATION LB-60 (BACK LIGHT DRIVE) CK-84 (FUNCTION SWITCH, IR) JK-170 (AV IN/OUT) MA-358 (MIC AMP, SIRCS IN) DD-123 (DC/DC CONVERTER) PD-110 RGB DECODER, LCD, TIMING GENERATOR INVERTER TRANSFORMER UNIT VC-217 SE-94 (MF DIAL) FOCUS/ZOOM MOTOR DRIVE, CAMERA, BLOCKING COMPRESS, VIDEO INTERFACE, DV PROCESS, REC/PB HEAD AMP, VIDEO IN/OUT, MECHANISM CONTROL, SERVO,...
Page 55: Flexible Boards Location
2-15.FLEXIBLE BOARDS LOCATION CONTROL SWITCH BLOCK (CF4550) FP-83 (CCD IMAGER) FP-90 CONTROL SWITCH (BRT, VOL CONTROL) BLOCK (PS4550) FP-82 FP-87 FP-91 FP-84 FP-85 (TRV10/10E) FP-586 (From LOADING MOTOR) (From DRUM MOTOR) LCD902 (included in FP-88) FP-242 (From LS CHASSIS) (From VIDEO HEAD) FP-92 (From LS CHASSIS) 2-10E...
Page 56: Block Diagrams
DCR-TRV8/TRV8E/TRV10/TRV10E SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM (TRV8/TRV8E)
Page 57: Overall Block Diagram (Trv10/Trv10E)
DCR-TRV8/TRV8E/TRV10/TRV10E 3-2. OVERALL BLOCK DIAGRAM (TRV10/TRV10E)
Page 58: Power Block Diagram
DCR-TRV8/TRV8E/TRV10/TRV10E 3-3. POWER BLOCK DIAGRAM 3-10 3-11 3-12E...
Page 59: Printed Wiring Boards And Schematic Diagrams
DCR-TRV8/TRV8E/TRV10/TRV10E SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)
Page 60 DCR-TRV8/TRV8E/TRV10/TRV10E DCR-TRV8/TRV8E/TRV10/TRV10E FP-83 (CCD IMAGER) PRINTED WIRING BOARD — Ref. No. FP-83 Flexible Board; 10,000 Series — FP-83 FLEXIBLE BOARD FP-83 BOARD CAMERA REC IC001 1,2 FP-83 BOARD C001 C002 C003 C004 6.8Vp-p CN001 A-2 CN002 B-1 IC001 IC001 IC001 3,4...
Page 61: Focus/Zoom Motor Drive
DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram • Refer to page 4-48 for printed wiring board. FOCUS/ZOOM MOTOR DRIVE 4-10 4-11 VC-217 (1/11)
Page 62: Camera
DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram • Refer to page 4-48 for printed wiring board. VC-217 BOARD (2/11) CAMERA REC IC203 @§,@¶ 1.0Vp-p IC203 2-!¡ 3.0Vp-p 56nsec IC202 5 CAMERA REC/PB 3.2Vp-p 36.0MHz IC202 !™ CAMERA REC/PB 18.0MHz 3.2Vp-p IC206 $º (X202) CAMERA REC/PB 3.0Vp-p...
Page 63: Blocking Compress
DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram • Refer to page 4-48 for printed wiring board. • This page is TRV10/TRV10E only. VC-217 BOARD (3/11) IC750 &¶ 2.8Vp-p 6.86MHz IC758 !£ 1.6Vp-p 20MHz BLOCKING COMPRESS 4-15 4-16 4-17 VC-217 (3/11)
Page 64: Video Interface
DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram • Refer to page 4-48 for printed wiring board. VC-217 BOARD (4/11) CAMERA REC/PB Q1500 E 0.12Vp-p Q1501 E 0.22Vp-p !º Q1502 E 0.28Vp-p !¡ Q1503 E 0.34Vp-p !™ Q1504 E 0.45Vp-p !£ IC1502 8 3.0Vp-p 13.5MHz...
Page 65 DCR-TRV8/TRV8E/TRV10/TRV10E DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram • Refer to page 4-48 for printed wiring board. VC-217 BOARD (5/11) CAMERA REC/PB !¢ IC1600 !¢ (X1600) 1.8Vp-p 24.58MHz DV PROCESS 4-21 4-22 4-23 VC-217 (5/11)
Page 66 DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram • Refer to page 4-48 for printed wiring board. VC-217 BOARD (6/11) !∞ IC1816 1267 CAMERA REC 3.5Vp-p 6.8msec !§ IC1816 @¶ PB 0.3Vp-p 6.8msec !¶ IC1900 !¡ CAMERA REC 2.2Vp-p 25nsec REC/PB HEAD AMP 4-25...
Page 67 DCR-TRV8/TRV8E/TRV10/TRV10E DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram • Refer to page 4-48 for printed wiring board. VC-217 BOARD (7/11) CAMERA REC/PB @£ !• IC1200 @∞ IC1402 @∞ LINE REC (NTSC) 0.44Vp-p 0.45Vp-p @¢ !ª IC1402 @ª IC1200 #£ LINE REC (NTSC) 0.37Vp-p 0.34Vp-p...
Page 68 DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram FP-91 (TOP/END SENSOR), FP-92 (TAPE LED), FP-242 (S/T REEL SENSOR) PRINTED WIRING BOARDS • Refer to page 4-48 for printed wiring board. — Ref. No. FP-91, 92, 242 Flexible Board; 10,000 Series — FP-91 FLEXIBLE FP-92 FLEXIBLE BOARD...
Page 69 DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram • Refer to page 4-48 for printed wiring board. VC-217 BOARD (9/11) CAMERA REC/PB @ª #∞ IC2503 4 IC2503 ^º 2.7Vp-p 2.6Vp-p 6.7msec 1.1msec 900kHz #º #§ IC2503 @™,@£,@¢ IC2503 ^£ 0.1Vp-p 0.23Vp-p 1.1msec 1.1msec 900kHz #¡...
Page 70 DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram • Refer to page 4-48 for printed wiring board. VC-217 BOARD (10/11) CAMERA REC/PB $º IC2204 $º (X2200) 2.8Vp-p 20.0MHz $¡ IC2204 %£ (X2201, C2232) 3.0Vp-p 32.767kHz HI CONTROL 4-41 4-42 4-43 4-44 VC-217 (10/11)
Page 71 DCR-TRV8/TRV8E/TRV10/TRV10E FP-82 (VC-CK CONNECT) PRINTED WIRING BOARD For schematic diagram ¥ Refer to page 4-48 for printed wiring board. — Ref. No. FP-82 Flexible Board; 10,000 Series — FP-82 BOARD CN41 CN42 For printed wiring boards • This board is two-layer print board. However, the pat- terns of layers two have not been included in the dia- gram.
Page 72 DCR-TRV8/TRV8E/TRV10/TRV10E VC-217 (FOCUS/ZOOM MOTOR DRIVE, CAMERA, BLOCKING COMPRESS, VIDEO INTERFACE, DV PROCESS, REC/PB HEAD AMP, VC-217 BOARD (SIDE A) VIDEO IN/OUT, MECHANISM CONTROL, SERVO, HI CONTROL, AUDIO) PRINTED WIRING BOARD — Ref. No. VC-217 Board; 10,000 Series — C205 C1512...
Page 73 DCR-TRV8/TRV8E/TRV10/TRV10E VC-217 (FOCUS/ZOOM MOTOR DRIVE, CAMERA, BLOCKING COMPRESS, VIDEO INTERFACE, DV PROCESS, REC/PB HEAD AMP, VIDEO IN/OUT, MECHANISM CONTROL, SERVO, HI CONTROL, AUDIO) PRINTED WIRING BOARD — Ref. No. VC-217 Board; 10,000 Series — VC-217 BOARD (SIDE B) C202 C-15...
Page 74: Printed Wiring Boards
DCR-TRV8/TRV8E/TRV10/TRV10E CK-84 (FUNCTION SWITCH, IR), CF4550 (CONTROL DIAL), FP-91 (PANEL REV/CLOSE) PRINTED WIRING BOARDS — Ref. No. CK-84 Board, CF4550, FP-91 Flexible Boards; 10,000 Series — CONTROL SWITCH BLOCK CK-84 BOARD (CF4550) BT8600 D-8 R7501 B-9 R7502 B-10 SELF PLAY...
Page 75 DCR-TRV8/TRV8E/TRV10/TRV10E CK-84 BOARD IC7501 $¡ PB 0.5Vp-p IC7501 $¡ LINE REC (NTSC) 0.5Vp-p IC7501 @™ (NTSC) LINE REC/PB (IR ON) 0.8Vp-p 82nsec FUNCTION SWITCH, IR CONTROL DIAL, PANEL REV/CLOSE 4-57 4-58 4-59 CK-84 CF4550/FP-91...
Page 76 DCR-TRV8/TRV8E/TRV10/TRV10E JK-170 (AV IN/OUT) PRINTED WIRING BOARD — Ref. No. JK-170 Board; 1,000 Series — JK-170 BOARD S VIDEO C400 CN400 F-11 J402 R459 C401 J403 R460 C450 D401 C451 D402 L400 S400 C453 D403 L401 C454 D404 L450 SE450...
Page 77 DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram MA-358 (MIC AMP, SIRCS IN) PRINTED WIRING BOARD • Refer to page 4-70 for SE-94 printed wiring board. — Ref. No. MA-358 Board; 10,000 Series — MA-358 BOARD C7300 CN7300 C-2 R7322 C-3 C7301 CN7306 B-3...
Page 78 DCR-TRV8/TRV8E/TRV10/TRV10E DCR-TRV8/TRV8E/TRV10/TRV10E SE-94 (MF DIAL), LB-60 (BACK LIGHT DRIVE) PRINTED WIRING BOARDS — Ref. No. SE-94 Board; 1,000 Series, LB-60 Board; 10,000 Series — LB-60 BOARD SE-94 BOARD C5013 L5201 PH081 B-1 PH082 C-2 C5101 L5202 C5102 C5104 ND5201 A-5...
Page 79: Back Light Drive
DCR-TRV8/TRV8E/TRV10/TRV10E DCR-TRV8/TRV8E/TRV10/TRV10E LB-60 BOARD CAMERA REC/PB IC5101 !∞ 12.0Vp-p BACK LIGHT DRIVE 4-73 4-74 4-75 LB-60...
Page 80: Printed Wiring Boards
DCR-TRV8/TRV8E/TRV10/TRV10E DCR-TRV8/TRV8E/TRV10/TRV10E FP-90 (BRT, VOL CONTROL), PD-110 (RGB DECODER, LCD, TIMING GENERATOR) PRINTED WIRING BOARDS — Ref. No. FP-90 Flexible Board, PD-110 Board; 10,000 Series — FP-90 FLEXIBLE BOARD BRIGHT (+) VOLUME (–) VOLUME (+) BRIGHT (–) CONTROL SWITCH BLOCK (CF4550)
Page 81 DCR-TRV8/TRV8E/TRV10/TRV10E PD-110 BOARD (1/2) CAMERA REC/PB IC5502 8 0.3Vp-p IC5502 9 0.22Vp-p IC5502 !º 0.14Vp-p IC5502 @º 3.5Vp-p IC5502 @™ 3.5Vp-p IC5502 @¢ 4.0Vp-p IC5502 $¡ 1.6Vp-p BRT, VOL CONTROL RGB DECODER, LCD 4-79 4-80 4-81 FP-90 PD-110 (1/2)
Page 82: Timing Generator
DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram ¥ Refer to page 4-77 for printed wiring board. PD-110 BOARD (2/2) CAMERA REC/PB IC5601 @§ 16.7MHz 3.0Vp-p IC5601 #¢ 2.7Vp-p !º IC5601 #¶ 2.7Vp-p !¡ IC5602 7 6.8Vp-p TIMING GENERATOR 4-82 4-83 4-84 PD-110 (2/2)
Page 83 DCR-TRV8/TRV8E/TRV10/TRV10E FP-85 (VTR CONTROL SWITCH BLOCK), PS4550 (S/S SWITCH) PRINTED WIRING BOARDS — Ref. No. FP-85, PS4550 Flexible Board; 10,000 Series — CONTROL SWITCH BLOCK FP-85 FLEXIBLE BOARD (PS4550) STOP PLAY STOP PHTO (PHOTO F) EDIT EDIT S69,S70 SEARCH (–)
Page 84: Color Evf, Dc/Dc Converter
DCR-TRV8/TRV8E/TRV10/TRV10E DD-123 (COLOR EVF, DC/DC CONVERTER) PRINTED WIRING BOARD — Ref. No. DD-123 Board; 10,000 Series — DD-123 BOARD C3200 C5012 Q3202 B-2 R3231 A-7 R5033 D-2 C3201 C5013 Q3202 C-1 R3232 B-8 R5034 D-3 C3202 C5015 Q3204 B-1 R3233 B-8...
Page 85 DCR-TRV8/TRV8E/TRV10/TRV10E DD-123 BOARD (1/2) CAMERA REC/PB IC5001 8 IC5102 $¡ 0.28Vp-p 16.06MHz 3.6Vp-p IC5001 9 IC5102 !• 2.8Vp-p 0.2Vp-p 17.0msec IC5001 !º IC5102 @º,@¡ 2.8Vp-p 0.15Vp-p 127 sec !º IC5001 @º IC5102 @™ 2.8Vp-p 7Vp-p !¡ IC5001 @™ IC5102 @£,@¢...
Page 86 DCR-TRV8/TRV8E/TRV10/TRV10E For schematic diagram • Refer to page 4-89 for printed wiring board. DD-123 BOARD (2/2) CAMERA REC/PB !™ IC3200 $• 4.5Vp-p 2.6msec !£ IC3200 $¶ 4.5Vp-p 2.6msec DC/DC CONVERTER 4-95 4-96 4-97 4-98E DD-123 (2/2)
Page 87: Adjustments
DCR-TRV8/TRV8E/TRV10/TRV10E SECTION 5 ADJUSTMENTS Before starting adjustment EVR Data Re-writing Procedure When Replacing Board The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.
Page 88: Adjusting Items When Replacing Main Parts And Boards
1-1. Adjusting items when replacing main parts and boards. • Adjusting items when replacing main parts When replacing main parts, adjust the items indicated by r in the following table. Replaced parts Block replacement Mounted parts replacement Adjustment Adjustment Section Initialization Initialization of C page data of B, C, D,...
Page 89 • Adjusting items when replacing a board or EEPROM When replacing a board or EEPROM, adjust the items indicated by r in the following table. Replaced parts Board replacement Adjustment Adjustment Section Initialization Initialization of C page data of B, C, D, Initialization of D page data E, F page Initialization of B page data...
Page 90: Camera Section Adjustment
5-1. CAMERA SECTION ADJUSTMENT 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Regulated power supply • Digital voltmeter Ref. No. Name Parts Code Usage Auto white balance adjustment/check Filter for color temperature correction (C14) J-6080-058-A White balance adjustment/check ND filter 1.0...
Page 91: Preparations
1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards Pattern Box need not be disassembled. Connect the equipment for adjustments according to Fig. 5-1-2. The front panel block (MA-358 board, focus ring, Audio/video jack, microphone unit) must be assembled because the focus ring and audio/video jack are used for adjustments.
Page 92 Cabinet (R) CN8607 CN8606 CN8603 CK-84 board CPC-8 jig CN8608 i J-6082-388-A j CN8605 AC power adaptor i 8.4Vdc) FP-82 AC-L10 or flexible AC-VQ800 Must be connected. Front panel block DC IN jack Must be connected Lens when performing CN2501 CN2907 block CN1810...
Page 93: Precaution
1-1-3. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. POWER switch (PS4550 block) ......CAMERA WHITE BALANCE (Menu display) ......AUTO NIGHT SHOT switch (Lens block) ......... OFF DISPLAY (Menu display) ......... V-OUT/LCD DEMO MODE (Menu display) ........
Page 94: Initialization Of B, C, D, E, F Page Data
1-2. INITIALIZATION OF B, C, D, E, F PAGE DATA 3. C Page Table 1-2-1. INITIALIZATION OF C PAGE DATA Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the C Page 1. Initializing the C Page Data Data”.) Note: If the C page data has been initialized, the following adjustments Fixed data-2 : Modified data.
Page 95 Initial value Initial value Address Remark Address Remark NTSC PAL NTSC PAL Emergency memory address Fixed data-1 (Initialized data) Fixed data-1 (Initialized data) PLL f fine adj. Fixed data-2 Fixed data-1 (Modified data, copy the data built in (Initialized data) the same model.) Fixed data-1 (Initialized data)
Page 96: Modification Of D Page Data
1-2-2. INITIALIZATION OF D PAGE DATA 1. Initializing the D Page Data Initial value Address Remark Note: If the D page data has been initialized, the following adjustments NTSC PAL need to be performed again. Fixed data-1 1) Modification of D page data 2) Color viewfinder system adjustments 3) LCD system Adjustments Fixed data-2...
Page 97 *1: No mark: DCR-TRV10/TRV10E < >: DCR-TRV8/TRV8E 3. D Page Table Initial value Address Remark Note : Fixed data-1 : Initialized data. (Refer to “1. Initializing the D Page NTSC PAL Data”.) Fixed data-2 Fixed data-2 : Modified data. (Refer to “2. Modification of D Page Data”.)
Page 98: Initialization Of B Page Data
*1: No mark: DCR-TRV10/TRV10E < >: DCR-TRV8/TRV8E 1-2-3. INITIALIZATION OF B PAGE DATA 1. Initializing the B Page Data Initial value Address Remark Note: If the B page data has been initialized, the following adjustments NTSC PAL need to be performed again.
Page 99 3. B Page Table Address Remark Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the B Page Fixed data-1 Data”.) (Initialized data) Fixed data-2 : Modified data. (Refer to “2. Modification of B Page Data”.) Fixed data-2 (Modified data, copy the data built in Address Remark the same model.)
Page 100: Modification Of E, F Page Data
1-2-4. INITIALIZATION OF E, F PAGE DATA Address Remark 1. Initializing the E, F Page Data Note: If the E, F page data has been initialized, following adjustments Fixed data-1 need to be performed again. (Initialized data) 1) Modification of E, F page data 2) Camera system adjustments Adjusting page Adjusting Address...
Page 101 3. F Page Table Initial value Address Remark Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the E, F NTSC PAL Page Data”.) Angular velocity sensor sensitivity Fixed data-2 : Modified data. (Refer to “2. Modification of E, F Page Data”.) adj.
Page 102 Initial value Initial value Address Remark Address Remark NTSC PAL NTSC PAL Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data)
Page 103 4. E Page Table Initial value Address Remark Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the E, F NTSC PAL Page Data”.) Fixed data-1 Fixed data-2 : Modified data. (Refer to “2. Modification of E, F Page Data”.) (Initialized data) Initial value Address...
Page 104 Initial value Address Remark NTSC PAL Fixed data-1 (Initialized data) AGC gain calibration adj. Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) Table.
Page 105: Camera System Adjustments
1-3. CAMERA SYSTEM ADJUSTMENTS 3. HALL Adjustment For detecting the position of the lens iris, adjust the hall AMP gain Before perform the camera system adjustments, check that the and offset. specified value of “VIDEO SYSTEM ADJUSTMENT” are satisfied. Subject Not required 1.
Page 106: Flange Back Adjustment (Using Minipattern Box)
4. Flange Back Adjustment (Using Minipattern Box) The inner focus lens flange back adjustment is carried out Adjusting method: automatically. In whichever case, the focus will be deviated during 1) Install the minipattern box so that the distance between it and auto focusing/manual focusing.
Page 107: Than 500M Away)
5. Flange Back Adjustment (Using Flange Back Adjustment Chart and Subject More Than 500m Away) The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. 5-2. Flange Back Adjustment (2) 5-1.
Page 108: Flange Back Check
6. Flange Back Check Subject Siemens star (2.0m from the front of the lens) (Luminance : approx. 200 lux) Measurement Point Check operation on TV monitor Measuring Instrument Specified Value Focused at the TELE end and WIDE end. Switch setting: 1) NIGHT SHOT ..............
Page 109: Optical Axis Adjustment
7. Optical Axis Adjustment Align the lens Optical Axis with the that of the CCD imager. If deviated, center of picture can lose focus when zoom is operated from the WIDE end to the TELE end. Subject Siemens star Measurement Point Check on the monitor TV Measuring Instrument Adjustment Page...
Page 110: Picture Frame Setting
8. Picture Frame Setting 9. AGC GAIN Calibration Adjustment Subject Color bar chart Subject Clear chart (Color reproduction adjustment (Color reproduction adjustment frame) frame) (1.5m from the front of the lens) Measurement Point Display data of page 1 (Note) Measurement Point Video output terminal Measuring Instrument Adjustment remote commander...
Page 111: Color Reproduction Adjustment
NIGHT SHOT ..............OFF frame. STEADY SHOT (Menu display) ........OFF Note: NTSC model: DCR-TRV8/TRV10 Adjusting method: PAL model: DCR-TRV8E/TRV10E Select page: 0, address: 01, and set data: 01. Select page: 6, address: 96, and set data: 00.
Page 112: Auto White Balance & Lv Standard Data Input
12. Auto White Balance & LV Standard Data Input 13. Auto White Balance Adjustment Adjust to the proper auto white balance output data. Subject Clear chart If it is not correct, auto white balance and color reproducibility will (Color reproduction adjustment be poor.
Page 113: White Balance Check
14. White Balance Check 15. Angular Velocity Sensor Sensitivity Adjustment • This adjustment is performed only when replacing the angular Subject Clear chart (Color reproduction velocity sensor. adjustment frame) Although this adjustment need not be performed when the circuit Filter Filter C14 for color temperature is damaged, etc., check the operations.
Page 114: Color Electronic Viewfinder System
1-4. COLOR ELECTRONIC VIEWFINDER 1. VCO Adjustment (DD-123 board) Set the VCO free-run frequency. If deviated, the EVF screen will be SYSTEM ADJUSTMENT blurred. Note 1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to Mode VTR stop avoid electrical shock.
Page 115: Bright Adjustment (Dd-123 Board)
2. Bright Adjustment (DD-123 board) 3. Contrast Adjustment (DD-123 board) Set the level of the VIDEO signal for driving the LCD to the specified Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated value.
Page 116: Backlight Consumption Current Adjustment
3) Press the PAUSE button of the adjustment remote commander. each time to set the data. 4) Select page: 0, address: 01, and set data: 00. Address DCR-TRV10 DCR-TRV8 Data DCR-TRV10E DCR-TRV8E 5) Check that the EVF screen is not colored. If colored, change the data of page: D, address: 71 and 72 so that the EVF screen is not colored.
Page 117: Lcd System Adjustment
1-5. LCD SYSTEM ADJUSTMENT 1. VCO Adjustment (PD-110 board) Set the VCO free-run frequency. If deviated, the LCD screen will Note 1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to be blurred.
Page 118: D Range Adjustment (Pd-110 Board)
2. D range Adjustment (PD-110 board) 3. Bright Adjustment (PD-110 board) Set the D range of the RGB decoder used to drive the LCD to the Set the level of the VIDEO signal for driving the LCD to the specified specified value.
Page 119: Contrast Adjustment (Pd-110 Board)
4. Contrast Adjustment (PD-110 board) 5. V-COM Level Adjustment (PD-110 board) Set the level of the VIDEO signal for driving the LCD to the specified Set the common electrode drive signal level of LCD to the specified value. If deviated, the screen image will be blackish or saturated value.
Page 120: V-Com Adjustment (Pd-110 Board)
8) Select page: 3, address: 22, set data: 00, and press the PAUSE button of the adjustment remote commander. DCR-TRV10 9) Select page: 3, address: 0C, set data: 00, and press the PAUSE DCR-TRV8 Data button of the adjustment remote commander. DCR-TRV10E 10) Select page: 0, address: 01, and set data: 00.
Page 121: Mechanism Section Adjustment
5-2. MECHANISM SECTION ADJUSTMENT On the mechanism section adjustment For details of mechanism section adjustments, checks, and replacement of mechanism parts, refer to the separate volume “DV MECHANICAL ADJUSTMENT MANUAL D Mechanism ”and “MECHANICAL ADJUSTMENT MANUAL D200 Mechanism ”. 2-1. HOW TO ENTER RECORD MODE WITHOUT 2-3.
Page 122: Video Section Adjustments
5-3. VIDEO SECTION ADJUSTMENTS NTSC model : DCR-TRV8/TRV10 PAL model : DCR-TRV8E/TRV10E 3-1. PREPARATIONS BEFORE ADJUSTMENTS Use the following measuring instruments for video section adjustments. 3-1-1. Equipment Required 1) TV monitor 2) Oscilloscope (dual-phenomenon, band above 30 MHz with delay mode) (Unless specified otherwise, use a 10 : 1 probe.) 3) Frequency counter 4) Pattern generator with video output terminal.
Page 123: Precautions On Adjusting
3-1-2. Precautions on Adjusting Note 1: Setting the “Forced VTR Power ON” mode (VTR mode) 1) Select page: 0, address: 01, and set data: 01. The adjustments of this unit are performed in the VTR mode 2) Select page: D, address: 10, set data: 02, and press the PAUSE or camera mode.
Page 124: Adjusting Connectors
3-1-3. Adjusting Connectors Some of the adjusting points of the video section are concentrated at VC-217 board CN2904. Connect the measuring instruments via the CPC-8 jig (J-6082-388-A). The following table lists the pin numbers and signal names of CN2904. CN2904 Pin No.
Page 125: Alignment Tapes
3-1-6. Alignment Tapes Use the alignment tapes shown in the following table. Use tapes specified in the signal column of each adjustment. Name Tracking standard (XH2-1) Tape path adjustment SW/OL standard (XH2-3) Switching position adjustment Audio operation check Audio system adjustment (XH5-3 (NTSC), XH5-3P (PAL)) System operation check Operation check...
Page 126: System Control System Adjustment
3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT 1. Initialization of B, C, D, E, F Page Data If the B, C, D, E, F page data is erased due to some reason, perform “1-2. INITIALIZATION OF B, C, D, E, F PAGE DATA”, of “5-1. CAMERA SECTION ADJUSTMENT”...
Page 127: Servo And Rf System Adjustment
3-3. SERVO AND RF SYSTEM ADJUSTMENT 2. T reel FG Duty Adjustment (VC-217 board) Adjust the take-up reel FG signal duty cycle to an appropriate value Before perform the servo and RF system adjustments, check that so that the correct T-reel FG signal is obtained. the specified value of “36 MHz Origin Oscillation Adjustment”...
Page 128: Switching Position Adjustment (Vc-217 Board)
4. Switching Position Adjustment (VC-217 board) 5. AGC Center Level and APC & AEQ Adjustment 5-1. Preparations before adjustments Mode VTR playback Mode Camera recording Signal SW/OL reference tape (XH2-3) Subject Arbitrary Measurement Point Display data of page: 3, address: 03 Measuring Instrument Adjustment remote commander Adjusting method:...
Page 129: Apc & Aeq Adjustment (Vc-217 Board)
5-3. APC & AEQ Adjustment (VC-217 board) 6. PLL f & LPF f Final Adjustment (VC-217 board) Mode Playback Mode VTR stop Signal Recorded signal at “Preparations Signal Arbitrary before adjustments” Measurement Point Display data of page: 3, address: 03 Pin @º...
Page 130: Video System Adjustments
3-4. VIDEO SYSTEM ADJUSTMENTS 2. S VIDEO OUT Y Level Adjustment (VC-217 board) Before perform the video system adjustments, check that the specified value of “36 MHz Origin Oscillation Adjustment” of Mode Camera “CAMERA SYSTEM ADJUSTMENT” is satisfied. Subject Arbitrary Measurement Point Y signal terminal of S VIDEO jack 3-4-1.
Page 131: S Video Out Chroma Level Adjustment
3. S VIDEO OUT Chroma Level Adjustment 4. AV OUT Y, Chroma Level Check (VC-217 board) (VC-217 board) Mode Camera Mode Camera Subject Arbitrary Subject Arbitrary Measurement Point Chroma signal terminal of S VIDEO Measurement Point Video terminal of AUDIO/VIDEO jack (75 terminated) jack (75...
Page 132: Pll Adjustment (Vc-217 Board)
5. PLL Adjustment (VC-217 board) (Except AEP/UK model) Set the VCO center level of the video input circuit (IC1200). Mode VTR stop Signal Color bar (Video terminal of AUDIO/ VIDEO jack input) Measurement Point Display data of page: 3, address: 04 Measuring Instrument Adjustment remote commander Adjustment Page...
Page 133: Bist Check
3-4-2. BIST Check 1. Playback System Check 1-1. Preparation for Playback Set the POWER switch to VTR (or PLAYER) position. When the playback system from IC1600(SFD) to IC2002 (ADC&DAC) is normal, the display data (combination data) Connect the adjusting remote commander and set the HOLD switch to ON (SERVICE) position.
Page 134: Ic1501(Vfd) Bist(Pb) Check
1-5. IC1501(VFD) BIST(PB) Check • UPY Cb BIST(PB) Check 1) Select page: 0, address: 01, and set data: 01. 20) Select page: 3, address: 10, set data: 8A, and press the PAUSE 2) Select page: C, address: 51, set data: 0F, and press the PAUSE button.
Page 135: Recording System Check
• ENC Ca BIST(PB) Check 2. Recording System Check 35) Select page: 3, address: 10, set data: 8D, and press the PAUSE 2-1. Preparations for recording button. 36) Select page: 3, address: 12, set data: 10, and press the PAUSE Playback the BIST check tape.(XH5-6(NTSC), XH5-6P(PAL)) button.
Page 136: Ic1601(Tfd) Bist(Rec) Check
2-5. IC1900(TRX) BIST(REC) Check 9) Select page: 3, address: 11, set data: 87, and press the PAUSE button. 1) Select page: 3, address: 12, set data: 04, and press the PAUSE 10) Select page: 3, address: 12, set data: 08, and press the PAUSE button.
Page 137: Ir Transmitter Adjustments
3-5. IR TRANSMITTER ADJUSTMENTS 2. IR Video Deviation Adjustment (CK-84 board) Mode VTR stop Adjust using a IR receiver jig (J-6082-383-A). Signal Arbitrary Measurement Point VIDEO OUT terminal of IR receiver jig Switch setting: (Terminated at 75 ) LASER LINK ........ON (Red LED is lit) Measuring Instrument Oscilloscope 1.
Page 138: Ir Audio Deviation Adjustment (Ck-84 Board)
3. IR Audio Deviation Adjustment (CK-84 board) Mode VTR stop Signal Video : No signal Audio : –400Hz, –7.5dBs, Audio left and right terminal of AUDIO/VIDEO jack Measurement Point AUDIO L terminal and AUDIO R terminal of IR receiver jig (Terminated at 47k ) Measuring Instrument Audio level meter...
Page 139: Audio System Adjustments
3-6. AUDIO SYSTEM ADJUSTMENTS [Connection of Audio System Measuring Devices] Connect the audio system measuring devices as shown in Fig. 5-3-14. Main unit Recording (Camera mode) Left Audio oscillator Right Attenuator 600 : 270 (1-249-410-11) + 330 (1-249-411-11) Playback Main unit TV monitor Video (Yellow) Left (White)
Page 140: Playback Level Check
1. Playback Level Check 4. Overall Noise Level Check Mode VTR playback Mode Camera recording and playback Signal Alignment tape: Signal No signal: Insert a shorting plug in the For audio operation check MIC jack (XH5-3 (NTSC)) Measurement Point Audio left or right terminal of AUDIO (XH5-3P (PAL)) VIDEO jack Measurement Point...
Page 141: Service Mode
5-4. SERVICE MODE 4-1. ADJUSTMENT REMOTE COMMANDER 2. Precautions upon using the adjustment remote commander The adjustment remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The Mishandling of the adjustment remote commander may erase the correct adjustment data at times.
Page 142: Data Process
4-2. DATA PROCESS The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.
Page 143: Service Mode
4-3. SERVICE MODE 2-1. EMG Code (Emergency Code) 1. Setting the Test Mode Codes corresponding to the errors which occur are written in Page D Address 10 addresses 38, 3C and 40. The type of error indicated by the code are shown in the following table.
Page 144: Msw Code
2-2. MSW Code MSW when errors occur: Information on MSW (mode SW) when errors occur MSW when movement starts: Information on MSW when movements starts when the mechanism position is moved (When the L motor is moved) MSW of target of movement: Information on target MSW of movement when the mechanism position is moved Mechanism Position UNLOAD...
Page 145: Bit Value Discrimination
3. Bit value discrimination Bit values must be discriminated using the display data of the adjustment remote commander for following items. Use the table below to discriminate if the bit value is “1” or “0”. Display on the adjustment remote commander Address Page bit3 to bit0 discrimination...
Page 146: Switch Check (2)
5. Switch check (2) Page 2 Address 60 to 67 Using method: 1) Select page: 2, address: 60 to 67. 2) By discriminating the display data, the pressed key can be discriminated. Data Address 00 (00 to 0A) 19 (0B to 24) 32 (25 to 44) 59 (45 to 6E) 85 (4F to 9F)
Page 147: Repair Parts List
DCR-TRV8/TRV8E/TRV10/TRV10E SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • Model The components identified by mark ! or have some differences from the original one. DCR-TRV8 DCR-TRV10 dotted line with mark ! are critical for safety.
Page 148: Cabinet (R) Section
6-1-2. CABINET (R) SECTION LCD panel (See page 6-3) supplied supplied SP901 supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 1-418-349-11 SWITCH BLOCK, CONTROL (CF4550) * 61 3-055-321-01 SHEET, GUARD 3-713-791-51 SCREW (M1.7X3.5), TAPPING, P2 * 62 3-055-322-01 PLATE, HINGE BLIND A-7073-970-A CK-84 BOARD COMPLETE (10/10E)
Page 149: Lcd Panel Section
6-1-3. LCD PANEL SECTION LCD902 not supplied ND901 LCD901 not supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-3949-669-1 CABINET (M) ASSY, P X-3949-767-1 CABINET (C) ASSY, P (10E:AEP,UK) 1-673-618-21 FP-90 FLEXIBLE BOARD X-3949-768-1 CABINET (C) ASSY, P (8E:HK,CN,AUS) 3-713-791-51 SCREW (M1.7X3.5), TAPPING, P2 X-3949-782-1 CABINET (C) ASSY, P (10E:HK,JE,CN,AUS) X-3949-631-1 FRAME ASSY, P...
Page 150: Chassis Section
6-1-4. CHASSIS SECTION not supplied 152 153 EVF assembly (See page 6-6) Mechanism deck (See page 6-7 to 6-10) RV61 Lens assembly (See page 6-6) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-3947-927-1 COVER ASSY 3-055-220-11 SHEET, VTR INDICATION X-3949-627-1 FRAME ASSY, MD 3-055-221-01 BUTTON, FK...
Page 151: Cabinet (L) Section
6-1-5. CABINET (L) SECTION supplied supplied not supplied not supplied not supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-055-199-01 BUTTON, SS * 210 3-055-189-01 FOOT (A) 1-418-350-11 SWITCH BLOCK, CONTROL (PS4550) 3-973-497-91 SCREW (M1.7), 0-NO. +P 2 X-3949-667-1 CABINET (L) ASSY (8E:AEP,UK) X-3949-611-1 CAP ASSY, LENS X-3949-673-1 CABINET (L) ASSY (10/10E:E)
Page 152: Evf And Lens Section
6-1-6. EVF AND LENS SECTION LCD903 not supplied IC001 not supplied M904 M905 Be sure to read “Precautions upon replacing CCD imager” on page 4-7 when changing the CCD imager. Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-3949-615-2 CABINET (UPPER) ASSY, VF...
Page 153 6-1-7. CASSETTE COMPARTMENT AND DRUM ASSY SECTION FP-242 (See page 6-8) not supplied Attaching procedure not supplied Note M901 Note: Once remove No. 720 CC fastener, don't use it again. Be sure to replace it with new one. (Attaching procedure is as shown above figure.) Ref.
Page 154: Ls Chassis Block Section
6-1-8. LS CHASSIS BLOCK SECTION Note 1: About FP-242 and FP-92 The FP-242 and FP-92 flexible boards are installed to a chassis with a hot press, which are included in the Ref. No. 762 chassis (D3) assy, LS block section, They are not supplied separately because the high precision for installation is needed. Note 2: Selecting the T washer Select proper parts for the Ref.
Page 155: Mechanism Chassis Block Section-1
6-1-9. MECHANISM CHASSIS BLOCK SECTION-1 Note: Be sure to remember the installed position (one of two position), direction and thickness of the Ref. No. 820 (head spacer) when the M902 (capstan motor )is removed. Refer to “3-9. Capstan motor” on page 15 in the “DV MECHANICAL ADJUSTMENT MANUAL ”...
Page 156: Mechanism Chassis Block Section-2
6-1-10. MECHANISM CHASSIS BLOCK SECTION-2 supplied not supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-3945-640-1 PULLEY ASSY, RELAY 3-748-738-02 GEAR, NO.2 3-315-414-31 WASHER 3-748-741-03 GEAR, NO.1 X-3748-600-1 ARM ASSY, COMPULSION 3-748-731-02 ARM, POSITION X-3748-605-1 CAM (S) ASSY X-3945-639-1 PULLEY ASSY, CONVERSION 3-976-452-01 LEVER, EJECT 3-748-734-01 BELT, RELAY...
Page 157: Electrical Parts List
! are critical for safety. ordering these items. • Model Replace only with part number specified. • CAPACITORS: DCR-TRV8 Les composants identifiés par une marque uF: µF DCR-TRV8E ! sont critiques pour la sécurité. • COILS DCR-TRV10 Ne les remplacer que par une pièce portant...
Page 158 CK-84 DD-123 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R7517 1-218-979-11 RES,CHIP 150K 1/16W A-7073-968-A DD-123(WS) BOARD, COMPLETE (10/10E) R7518 1-218-950-11 RES,CHIP 1/16W ************************** R7519 1-218-963-11 RES,CHIP 6.8K 1/16W A-7074-025-A DD-123(WSL) BOARD, COMPLETE (8/8E) R7520 1-218-949-11 RES,CHIP 1/16W ***************************...
Page 159 DD-123 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C3245 1-164-505-11 CERAMIC CHIP 2.2uF C5122 1-164-940-11 CERAMIC CHIP 0.0033uF 10% C3246 1-164-505-11 CERAMIC CHIP 2.2uF C5123 1-125-777-11 CERAMIC CHIP 0.1uF C3247 1-135-259-11 TANTAL. CHIP 10uF 6.3V C3248 1-164-505-11 CERAMIC CHIP 2.2uF...
Page 160 DD-123 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < IC LINK > Q3251 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO Q3252 8-729-037-74 TRANSISTOR UN9213J-(K8).SO ! PS3200 1-576-286-21 FUSE, MICRO (1.4A) Q3253 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO ! PS3201 1-576-286-21 FUSE, MICRO (1.4A) Q5102 8-729-037-61 TRANSISTOR UN9113J-(K8).SO ! PS3202 1-576-286-21 FUSE, MICRO (1.4A)
Page 161 DD-123 FP-92 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R3246 1-218-969-11 RES,CHIP 1/16W R5020 1-218-975-11 RES,CHIP 1/16W R3247 1-208-935-11 RES,CHIP 100K 0.50% 1/16W R5021 1-218-971-11 RES,CHIP 1/16W R3248 1-218-941-11 RES,CHIP 1/16W R5022 1-218-985-11 RES,CHIP 470K 1/16W R3249 1-218-945-11 RES,CHIP...
Page 162 FP-92 FP-242 FP-586 JK-170 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < TRANSISTOR > < CONNECTOR > Q901 8-729-028-71 TRANSISTOR PN166.SO (TAPE TOP) CN400 1-784-939-11 CONNECTOR, BOARD TO BOARD 60P Q902 8-729-028-71 TRANSISTOR PN166.SO (TAPE END) <...
Page 163 LB-60 MA-358 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7073-969-A LB-60 BOARD, COMPLETE R5107 1-218-970-11 RES,CHIP 1/16W R5108 1-218-982-11 RES,CHIP 270K 1/16W ********************* (Ref.No.:10000 Series) R5109 1-218-973-11 RES,CHIP 1/16W R5110 1-218-974-11 RES,CHIP 1/16W R5111 1-218-965-11 RES,CHIP 1/16W <...
Page 164 1-218-965-11 RES,CHIP 1/16W R7326 1-208-910-11 RES,CHIP 9.1K 1/16W < DIODE > R7327 1-218-964-11 RES,CHIP 8.2K 1/16W D7300 8-719-061-82 DIODE TLSU1002(TPX1,SONY) R7328 1-218-968-11 RES,CHIP 1/16W D7306 8-719-062-16 DIODE 01ZA8.2(TPL3) R7329 1-216-001-00 METAL CHIP 1/10W D7401 8-719-056-23 DIODE MA2S111-(K8).SO R7331 1-218-965-11 RES,CHIP...
Page 165 PD-110 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C5506 1-125-777-11 CERAMIC CHIP 0.1uF < IC > C5507 1-135-318-11 TANTAL. CHIP 33uF C5508 1-125-777-11 CERAMIC CHIP 0.1uF IC5501 8-759-530-19 IC MB40D001PFV-G-BND-ER C5509 1-135-221-11 TANTAL. CHIP 3.3uF IC5502 8-759-539-27 IC IR3Y37A4 C5510...
Page 166 PD-110 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R5518 1-208-719-11 RES,CHIP 0.50% 1/16W R5630 1-218-973-11 RES,CHIP 1/16W R5520 1-218-984-11 RES,CHIP 390K 1/16W R5634 1-218-961-11 RES,CHIP 4.7K 1/16W R5521 1-208-709-11 RES,CHIP 0.50% 1/16W R5640 1-208-935-11 RES,CHIP 100K 0.50% 1/16W (8/8E/10)
Page 167 PD-110 SE-94 VC-217 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R5686 1-218-973-11 RES,CHIP 1/16W C216 1-164-943-11 CERAMIC CHIP 0.01uF (10) C217 1-115-156-11 CERAMIC CHIP R5686 1-218-974-11 RES,CHIP 1/16W C218 1-107-826-91 CERAMIC CHIP 0.1uF (8/8E/10E) C219 1-164-846-11 CERAMIC CHIP 0.5PF R5687...
Page 168 VC-217 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C323 1-107-820-11 CERAMIC CHIP 0.1uF C1207 1-117-919-11 TANTAL. CHIP 10uF 6.3V C750 1-164-360-11 CERAMIC CHIP 0.1uF (EXCEPT AEP,UK) (10/10E) C1208 1-164-943-11 CERAMIC CHIP 0.01uF C751 1-127-760-91 CERAMIC CHIP 4.7uF 6.3V (EXCEPT AEP,UK)
Page 169 VC-217 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C1418 1-125-837-91 CERAMIC CHIP 6.3V C1860 1-164-943-11 CERAMIC CHIP 0.01uF C1422 1-125-838-91 CERAMIC CHIP 2.2uF 6.3V C1869 1-164-943-11 CERAMIC CHIP 0.01uF C1423 1-127-569-91 TANTAL. CHIP 100uF C1875 1-117-919-11 TANTAL.
Page 170 VC-217 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C2212 1-119-749-11 TANTAL. CHIP 33uF C2585 1-125-777-11 CERAMIC CHIP 0.1uF C2213 1-104-851-11 TANTAL. CHIP 10uF C2586 1-125-777-11 CERAMIC CHIP 0.1uF C2215 1-164-943-11 CERAMIC CHIP 0.01uF C2587 1-125-777-11 CERAMIC CHIP 0.1uF C2224 1-164-943-11 CERAMIC CHIP...
Page 171 VC-217 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks FB1606 1-414-813-11 FERRITE 0UH L302 1-414-771-91 INDUCTOR CHIP 10uH FB1607 1-414-813-11 FERRITE 0UH L305 1-414-771-91 INDUCTOR CHIP 10uH FB1801 1-414-760-21 FERRITE 0UH L750 1-414-771-91 INDUCTOR CHIP 10uH (10/10E) FB1802 1-414-760-21 FERRITE 0UH L751 1-414-771-91 INDUCTOR CHIP 10uH (10/10E)
Page 172 VC-217 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks Q1209 8-729-807-86 TRANSISTOR 2SB1295-UL5/6-TB R218 1-218-941-11 RES,CHIP 1/16W (EXCEPT AEP,UK) R221 1-218-985-11 RES,CHIP 470K 1/16W Q1400 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO R230 1-218-977-11 RES,CHIP 100K 1/16W (EXCEPT AEP,UK) R234 1-218-977-11 RES,CHIP 100K 1/16W...
Page 173 VC-217 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R326 1-218-953-11 RES,CHIP 1/16W R783 1-218-977-11 RES,CHIP 100K 1/16W R327 1-218-965-11 RES,CHIP 1/16W (10/10E) R328 1-218-957-11 RES,CHIP 2.2K 1/16W R785 1-218-977-11 RES,CHIP 100K 1/16W R329 1-218-973-11 RES,CHIP 1/16W (10/10E) R330...
Page 174 VC-217 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R1209 1-218-979-11 RES,CHIP 150K 1/16W R1507 1-218-949-11 RES,CHIP 1/16W (EXCEPT AEP,UK) R1508 1-218-959-11 RES,CHIP 3.3K 1/16W R1210 1-218-953-11 RES,CHIP 1/16W R1509 1-218-953-11 RES,CHIP 1/16W (EXCEPT AEP,UK) R1510 1-218-949-11 RES,CHIP 1/16W R1211...
Page 175 VC-217 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R1871 1-218-939-11 RES,CHIP 1/16W R2225 1-218-985-11 RES,CHIP 470K 1/16W R1872 1-218-990-11 SHORT R2226 1-218-985-11 RES,CHIP 470K 1/16W R1874 1-218-989-11 RES,CHIP 1/16W R2227 1-218-977-11 RES,CHIP 100K 1/16W R1875 1-218-965-11 RES,CHIP 1/16W R2229...
Page 176 VC-217 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R2288 1-218-953-11 RES,CHIP 1/16W R2532 1-217-671-11 METAL CHIP 1/10W R2289 1-218-953-11 RES,CHIP 1/16W R2533 1-217-671-11 METAL CHIP 1/10W R2290 1-218-953-11 RES,CHIP 1/16W R2534 1-218-940-11 RES,CHIP 1/16W R2291 1-218-953-11 RES,CHIP 1/16W R2546...
Page 177 VC-217 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R2927 1-218-990-11 SHORT 0 (8E:AEP,UK/10E:AEP,UK) LCD903 8-753-023-37 LCX024AK-1 (8/8E) R2928 1-218-950-11 RES,CHIP 1/16W LCD903 8-753-023-51 LCX027AK-1 (10/10E) R2929 1-218-954-11 RES,CHIP 1.2K 1/16W M901 A-7048-900-A DRUM BLOCK ASSY (DEH-07F-R) M902 8-835-524-04 MOTOR, DC SCD-0101A (CAPSTAN) <...
Page 178 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-053-056-01 LID, BATTERY CASE (For RMT-811,RMT-812) 3-866-727-41 MANUAL, INSTRUCTION (10/10E) (SPANISH,PORTUGUESE)(10:E,HK/10E:AEP) 3-742-854-21 LID, BATTERY CASE (For RMT-808,RMT-809) 3-866-727-61 MANUAL, INSTRUCTION (ARABIC,PERSIAN) (8/8E) (10E:CN,E) 3-866-261-11 MANUAL, INSTRUCTION (ENGLISH) 3-866-727-71 MANUAL, INSTRUCTION (10:E,HK,JE) (SIMPLIFIED CHINESE)(10E:CN,E) 3-866-261-31 MANUAL, INSTRUCTION...
Page 179 PARTS REFERENCE SHEET You can find the parts position of location of mount locations applying to VC-217 board of a set. VC-217 SIDE A DCR-TRV8/TRV8E/TRV10/TRV10E IC2503 IC2504 I C 1 8 1 6 IC2505 IC203 I C 1 9 0 0...
Page 180 OPTICAL AXIS FRAME Take a copy of OPTICAL AXIS FRAME with a clear sheet for use. — 264 —...
Page 181 FOR CAMERA COLOR REPRODUCTION ADJUSTMENT For NTSC model DCR-TRV8/TRV10 Take a copy of CAMERA COLOR REPRODUCTION FRAME and Parts referencesheets with a clear For PAL model sheet for use. DCR-TRV8E/TRV10E — 265 —...
Page 182 DCR-TRV8/TRV8E/TRV10/TRV10E Sony Corporation 99D1634-1 Printed in Japan ©1999.4 Personal A&V Products Company 9-974-161-11 Published by Quality Engineering Dept. — 266 — (Shinagawa)

This manual is also suitable for:

Dcr-trv8e Dcr-trv10 Rmt-808 Rmt-809 Rmt-811 Rmt-812 ... Show all

Sony DCR-TRV8 Service Manual

Service Note

Self-Diagnosis Function

General

Disassembly

Block Diagrams

Printed Wiring Boards and Schematic Diagrams

Adjustments

Repair Parts List

Quick Links

Related Manuals for Sony DCR-TRV8

Summary of Contents for Sony DCR-TRV8

This manual is also suitable for:

Table of Contents