Table of Contents
Quick Links
Hitachi Plasma Display Ceiling Mount Unit
Model
CMPAT04
Thank you for purchasing the Hitachi Plasma Display Ceiling Mount Unit.
To ensure correct usage, please read this instruction manual thoroughly. After reading, please store this manual
in a safe place for future reference.
This plasma display ceiling mount unit is for use only with the following models : CMP401X, CMP402HD, CMP307X
Special techniques are necessary for installation of
the plasma display.
Do not attempt to perform this work by yourself.
Request an installation specialist to install this unit.
This company assumes absolutely no responsibility
for injuries and damages that may occur due to
improper installation and handling.
Parts Configuration Chart
Packed in a temporarily assembled condition
Coupling pin
2
X
Usage cautions to ensure correct usage
Symbols
WARNING
CAUTION
This symbol indicates
additional cautions
(including warnings).
Caution
(general)
Ceiling mount unit
1
X
Snap pin
2
X
Angle
(left)
adjustment unit
1
X
The following symbols are used to ensure safe usage of the product, to prevent danger to
yourself and other parties and to prevent damage to property.
This symbol indicates that incorrect handling due to ignoring this symbol
can result in the possibility of personal injury or even death.
This symbol indicates that incorrect handling due to ignoring this symbol
can result in the possibility of personal injury and physical damage.
Forbidden
(general)
Installation Instructions
To dealers and shops
To ensure customer safety, be sure to design the
installation location so that the strength is sufficient
to withstand the weight of both the plasma display
and the Ceiling mount unit.
Always use at least two persons for all
installations.
Firmly install coupling pins, snap pins and screws
as specified in the installation instructions.
(right)
Display mount fitting
1 each left/right
This symbol indicates
forbidden actions.
Disassembly
prohibited
In the parts packing
M6
18 screw
X
8
X
Parts for CMP401X only
Support
M4 x 12 screw
2
X
X
This symbol indicates
required actions.
Indicates that the power
Required
plug is to be disconnected
(general)
from the power outlet.
4
Table of Contents
Related Manuals for Hitachi CMPAT04
Summary of Contents for Hitachi CMPAT04
-
Page 1: Installation Instructions
Model CMPAT04 Installation Instructions Thank you for purchasing the Hitachi Plasma Display Ceiling Mount Unit. To ensure correct usage, please read this instruction manual thoroughly. After reading, please store this manual in a safe place for future reference. This plasma display ceiling mount unit is for use only with the following models : CMP401X, CMP402HD, CMP307X... -
Page 2: Safety Cautions
Safety Cautions WARNING When a malfunction occurs, disconnect the power plug from the power outlet and take measures to prevent other people coming near the plasma display. In the cases such as Disconnect the The plasma display is loose and vibrates to an extreme degree, power plug from the power outlet. - Page 3 CAUTION Do not install close Do not install near to an air- sprinklers or conditioner intake sensors. or outlet. This could result in Do not install in misoperation or locations where electrical shock. there is excessive amounts of dust, oily smoke or tobacco smoke.
-
Page 4: Installation Method
Installation Method Installation space While referring to the dimensional drawing for the ceiling mount unit, decide an installation location where the ceiling strength is sufficient. Also, set the height adjustment position, screen tilt angle and horizontal angle of the ceiling mount unit beforehand. C M P 4 0 1 X (307) (121) - Page 5 C M P 3 0 7 X (284) (121) Screen center Ceiling mount unit dimensions Four 12mm dia. holes Pipe dia. 61mm Adjustment range Height adjustment: 180mm (P60 x 3 steps) Downward tilt angle adjustment: 0, 5, 10, 15, 20, 25 (6 steps) Horizontal angle adjustment: 45 degrees left or right (continuous) - 5 -...
- Page 6 Installing the ceiling mount unit 1. Disassembly Ceiling mount unit Remove the Slightly loosen the 4 lock 2 snap pins. remove the screws and 1 rotation stopper 2 coupling screw. pins. Merely slightly loosen the above screws. Do not remove Loosen the them.
- Page 7 4. Installing the angle adjustment unit 1. Pass the wiring cables 2.Insert 2 snap pins. through the pipe, then insert the angle adjustment unit Ceiling mount unit into the ceiling mount unit. Adjust the height so that the red mark on the pipe is not 3.Tighten the visible and then insert the 4 lock screws.
- Page 8 2. Installing the CMP401X supports 3. Installing the display mounts Fasten the two supports to the back of the plasma fasten the two display mounts to the back of the display with 4 M4 12 screws. plasma display with 6 M6 18 screws.
- Page 9 Installing the plasma display on the angle adjustment unit To fasten the plasma display to the ceiling mount unit, engage the four pins of the angle adjustment unit in the four cutouts of the display mount fitting on the back of the plasma display. Next, tighten the two screws from the bottom.
-
Page 10: Product Specifications
Angle adjustment 0, 5, 10, 15, 20, 25 degrees (6 steps) Horizontal angle 45 degrees (continuous) adjustment Vertical (tilt) angle 180mm (P60mm 3 steps) adjustment Products mounted Hitachi Plasma Displays CMP401X, CMP402HD and CMP307X Hitachi, Ltd. Tokyo Japan 2-15-12 Nishi-Shimbashi, Minato-ku, Tokyo, Digital Media Systems (03) 3502-2111 105-8430, Japan Division...