Page 3
TATE OF ALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM ASH HANDS AFTER HANDLING DECLARATION OF CONFORMITY according to FCC Part 15 Responsible Party Name: Fujitsu America, Incorporated Address: 1250 E. Arques Avenue, Sunnyvale, CA 94085 Telephone: (408) 746-6000 Base Model Configuration: ...
IMPORTANT SAFETY INSTRUCTIONS This unit requires an AC adapter to operate. Use only UL Listed I.T.E. Class II Adapters with an output rating of 19 VDC, with a minimum current of 2.1 A (40 W). AC adapter output polarity: When using your notebook equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: •...
Page 5
* To order a new battery for your Fujitsu mobile computer, go to the Fujitsu shopping site at www.shopfujitsu.com in the US or www.fujitsu.ca/products/notebooks in Canada. ** RBRC is an independent third party to which Fujitsu provides funding for battery recycling. RBRC is in no way affiliated with Fujitsu.
Preface About This Guide The LifeBook UH900 notebook from Fujitsu America is an ultra-mobile notebook computer. It is powered by an Intel® Atom™ Z530 processor, has a built-in color display with a passive digitizer, and brings the computing power of desktop personal computers (PCs) to a handheld, versatile environment.
LEASE READ ALL WARNING INFORMATION CAREFULLY Fujitsu Contact Information Service and Support You can contact Fujitsu Service and Support in the following ways: • Toll free: 1-800-8Fujitsu (1-800-838-5487) • Website: http://www.computers.us.fujitsu.com/support Before you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution: •...
Page 14
OU MUST HAVE AN ACTIVE INTERNET CONNECTION TO USE THE ONLINE LINKS Limited Warranty Your LifeBook UH900 ultra-mobile notebook is backed by a Fujitsu International Limited Warranty. Check the service kit that came with your notebook for the Limited Warranty period and terms and conditions.
Getting to Know Your LifeBook Overview This section describes the components of your Fujitsu LifeBook UH900 notebook. We strongly recommend that you read it before using your notebook – even if you are already familiar with notebook computers. Figure 1. Fujitsu LifeBook UH900 notebook...
Locating the Controls and Connectors Connectors and peripheral interfaces on the LifeBook UH900 notebook and the external monitor/LAN adapter cable allow you to connect and control a variety of devices. Specific locations are illustrated in Figures 2 through 6. The table below provides a short description of each icon on the LifeBook UH900 notebook and/or adapter cable.
Page 17
Connection Notebook Purpose Icon Wireless LAN/ The wireless LAN/Bluetooth switch allows you to turn power to the wireless Bluetooth LAN device and Bluetooth devices on and off. On-Off Switch (Available using external monitor/LAN adapter cable only.) External Video The external video port allows you to connect an external monitor or LCD port projector to your computer.
Top Components The following is a brief description of your LifeBook notebook’s top components when it is open. (See Figure 2 on page 17 for location) Web Camera The .78 megapixel web camera allows you to take pictures of yourself to send over the internet. Built-in Microphones The built-in microphones allows you to input audio.
Left and Right Buttons These buttons act the same as the left and right buttons on a mouse. Cursor Control The cursor control is used to move the cursor around the screen. USB port USB port Speaker SD card slot External Monitor/LAN adapter cable connector Figure 3.
External Monitor/LAN Adapter Cable Connector This connector allows you to connect the adapter cable to your notebook. See “External Video Port” on page 63. Secure Digital (SD) Card Slot The SD card slot allows you to install an SD card for data storage. This architecture allows you to transfer data from a variety of different digital devices.
O PROTECT YOUR NOTEBOOK FROM DAMAGE AND TO OPTIMIZE SYSTEM PERFORMANCE BE SURE TO KEEP ALL AIR VENTS UNOBSTRUCTED CLEAN AND CLEAR OF DEBRIS HIS MAY REQUIRE PERIODIC CLEANING DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED O NOT OPERATE THE NOTEBOOK IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED SUCH AS IN TIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION DC Power Jack...
Air Vents Polymer Battery Battery Latches Figure 6. LifeBook notebook bottom panel Bottom Components The following is a brief description of your LifeBook notebook’s bottom panel components. Polymer Battery Most of the bottom of the notebook is comprised of the internal polymer battery. It can be unlatched to remove the battery when stored over a long period of time or for swapping a discharged battery with a charged polymer battery.
Battery Latches The battery latches are used to secure the polymer battery to the bottom of the system. Air Vents The air vents allow air to circulate through the system to cool down the components. O PROTECT YOUR NOTEBOOK FROM DAMAGE AND TO OPTIMIZE SYSTEM PERFORMANCE BE SURE TO KEEP ALL AIR VENTS UNOBSTRUCTED CLEAN...
Figure 7. Status Indicator Panel Status Indicator Panel The Status Indicators display symbols that correspond to specific components of your Fujitsu LifeBook notebook. The LEDs below each symbol tell you how each of those components is operating. The Status Indicators are located in two different areas (Figure 7). Keyboard-related indicators are above the keyboard towards the left, and the remaining indicators are below the keyboard on the front edge.
Page 25
Battery Charge/DC-In Indicator • Orange, solid: AC adapter and battery are available and system is being charged. • Blue, solid: AC adapter and battery are available and system is fully charged, or AC adapter is plugged in but battery is not installed. •...
Page 26
• Batteries subjected to shocks, vibration or extreme temperatures can be permanently damaged. • A shorted battery is damaged and must be replaced. Flash Memory Disk Access Indicator The Flash Memory Disk Access indicator flickers blue when your internal flash memory is being accessed.
Once you have turned on your notebook, you may want to adjust the brightness level of the screen to a more comfortable viewing level. There are three ways to adjust the brightness: keyboard, power management utility, and Fujitsu Menu. 27 - Display Panel...
Page 28
Using the Fujitsu Menu to Adjust Brightness To adjust brightness using the Fujitsu menu, click on the Fujitsu Menu icon in the system tray in the lower right corner of the screen. (You can also open the Fujitsu menu by clicking the [Fn] button twice in succession.) Double-click Windows Mobility Center, then double-click the icon adjacent to Display...
Handling the System Your LifeBook UH900 notebook is designed to be handheld or used on a secure surface. When holding the notebook, use the following methods for optimal results. O NOT USE THE NOTEBOOK ON YOUR LAP SING IT ON YOUR LAP WILL BLOCK THE AIR VENTS WHICH COULD RESULT IN DAMAGE TO THE SYSTEM AND ALSO CAN REDUCE THE EXPOSURE SAFETY...
Start Key Figure 9. Keyboard Using the Keyboard Your Fujitsu LifeBook notebook has an integral 75-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the special function keys. This section describes the special keys. Start Key Your LifeBook notebook Start key displays the Start menu.
Page 31
Cursor Keys The cursor keys are the four arrow keys on the keyboard which are used to move the cursor up, down, left and right in applications. In programs such as Windows Explorer, it moves the “focus” (selects the next item up, down, left, or right).
Using the Cursor Buttons Left Button Scroll Button (up) Right Button Scroll Button (down) Cursor Control Figure 10. Cursor Buttons The button array on your LifeBook notebook is used to control the movement of the cursor and to select items on your display panel. The buttons consist of a cursor control at the top right above the keyboard, left and right buttons on the top left, and scroll buttons on the right of the display.
Page 33
Clicking Clicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the Left button once, and then immediately release it. You can also left-click by moving the cursor to the item you wish to select, then tapping the cursor control once.
Dragging Dragging means pressing and holding the left button, while moving the cursor control. To drag, move the cursor to the item you wish to move. Press and hold the left button while moving the item to its new location and then release it. Figure 13.
Using the Touch Screen The integrated multi-touch Touch Screen allows you to use your finger or a stylus as a pointing device. You can click, double-click, drag items and icons, or to draw like a pen or pencil in applications that support this behavior, such as drawing or painting programs.
Clicking on Touch Screen To left-click, touch the object you wish to select and then lift your finger or the stylus tip immediately. Right-Clicking on Touch Screen Right-click can be accomplished by holding your fingertip or a stylus down until a circular icon appears. To change the settings for the right-click feature, go to Start >...
Dragging Dragging means moving an item with the stylus by touching the screen, moving and then lifting your fingertip or the stylus. To drag, touch the Touch Screen on the item you wish to move. While continuing to touch the screen with your fingertip or the stylus, drag the item to its new location by moving it across the screen, and then lifting your fingertip or the stylus to release it.
Rotate Gesture To change the orientation of an object on the screen, place two fingers on the image you want to rotate, then move them in opposite directions (as if you were turning a knob). The direction the item turns is dependant upon the direction you move your fingers.
Volume Control Your Fujitsu LifeBook notebook has multiple volume controls which interact with each other. NY SOFTWARE THAT CONTAINS AUDIO FILES WILL ALSO CONTAIN A VOLUME CONTROL OF ITS OWN YOU INSTALL AN EXTERNAL AUDIO DEVICE THAT HAS AN INDEPENDENT VOLUME CONTROL...
NOTE: Arrows point to icons. In all cases, the actual button is adjacent to the icon. Zoom Button Scroll Up ECO Button Button Application Scroll Down A Button Button Figure 19. LifeBook UH900 Notebook Application Buttons LifeBook Application Buttons A unique feature of your LifeBook UH900 notebook is the array of Application buttons. These buttons allow you to launch specific applications and functions with the touch of a button.
ECO Button By default, the ECO Button is used to initiate the Power Saving Utility. To turn off the utility, press the button again. The ECO Button can also be programmed to launch whichever application you wish. See “Changing Button Functions” on page 41 to select a different application for this button. Application Button A The Application A Button can be used to automatically open pre-selected applications.
Using the Touch Launcher The Touch Launcher is a handy on-screen method for quickly launching commonly-used applications and performing Internet tasks. Depending upon your operating environment, the launcher will either be in Launcher Mode (Fig. 20) or Internet Mode (Fig. 21). In Launcher Mode, certain Windows actions can be performed such as Print and Close Window.
Chapter 2 Getting Started with Your LifeBook Power Sources Your Fujitsu LifeBook notebook has three possible power sources: a primary polymer battery, an AC adapter or an optional Auto/Airline adapter. Connecting the Power Adapters The AC adapter or optional Auto/Airline adapter provides power for operating your notebook and charging the batteries.
Page 44
Switching from AC Adapter Power or the Auto/Airline Adapter to Battery Power Be sure that you have at least one charged battery installed. Remove the AC adapter or the Auto/Airline adapter. HE POLYMER BATTERY IS NOT CHARGED UPON PURCHASE NITIALLY YOU WILL NEED TO CONNECT EITHER THE ADAPTER OR THE...
Starting Your LifeBook Notebook Power On Power/Suspend/Resume Button The Power/Suspend/Resume button allows you to suspend notebook activity without powering off, resume your LifeBook notebook from sleep mode, and power on your notebook when it has been shut down from Windows. HEN YOU TURN ON YOUR OOK NOTEBOOK BE SURE YOU HAVE A POWER SOURCE...
This information is in the BIOS program. Each time you power up or restart your notebook, it goes through a boot sequence which displays a Fujitsu logo until your operating system is loaded. During booting, your notebook is performing a standard boot sequence including a Power On Self Test (POST).
Turn on or restart your LifeBook notebook. To enter the BIOS Setup Utility, press the [F2] key once the Fujitsu logo appears on the screen. This will open the main menu of the BIOS Setup Utility with the current settings displayed.
When you turn on your notebook for the first time, it will display a Fujitsu logo on the screen. If you do nothing the system will load the operating system, and then the Windows Welcome will begin.
Your system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. For more information about the FDU utility, refer to “Automatically Downloading Driver Updates” on page 81.
Power Management Your LifeBook notebook has many options and features for conserving battery power. Some of these features are automatic and need no user intervention. However, others depend on the parameters you set to best suit your operating conditions, such as those for the display brightness. Internal power management for your notebook may be controlled from settings made in your operating system, pre-bundled power management application, or from settings made in BIOS setup utility.
Your notebook can be put in Sleep mode by: • Pressing the Power/Suspend/Resume button when your system is turned on. • Selecting Sleep (“Standby” in Windows XP) from the Windows Shut Down menu. • Timing out from lack of activity. •...
From the Control Panel select System and Security, then select Power Options. Select Choose what the power button does or Choose what closing the lid does, then make your selection (Do Nothing, Sleep, Hibernate, or Shut Down). You can also go directly into Hibernate mode by going to the Start menu, clicking the small arrow to the right of the [Shut Down] button, then clicking on Hibernate.
Sleep mode, press the Suspend/Resume Button. Energy saving benefits: Fujitsu ENERGY STAR qualified mobile PCs use about half as much electricity as standard equipment – saving half in utility costs. But more than that, ENERGY STAR also makes a difference for the environment.
Page 54
To learn more about the important ENERGY STAR program, visit: www.energystar.gov. To read about how Fujitsu is supporting Sustainable Management along with several other environmental activities, visit the Fujitsu Corporate Citizenship page at: http://www.computers.us.fujitsu.com/www/content/aboutus/environmental/environment.php 54 - Power Management...
Chapter 3 User-Installable Features Polymer Battery Your LifeBook notebook has a polymer battery that provides power for operating your notebook when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals, or other hazards.
• BATTERY LIFE WILL VARY BASED ON SCREEN BRIGHTNESS APPLICATIONS FEATURES POWER MANAGEMENT SETTINGS BATTERY CONDITION AND OTHER CUSTOMER PREFERENCES PTICAL DRIVE USAGE MAY ALSO HAVE A SIGNIFICANT IMPACT ON BATTERY LIFE HE BATTERY CHARGING CAPACITY IS REDUCED AS THE BATTERY AGES F YOUR BATTERY IS RUNNING LOW QUICKLY YOU SHOULD REPLACE IT WITH A NEW ONE...
Page 57
SING HEAVY CURRENT DEVICES OR FREQUENT EXTERNAL OPTICAL DRIVE ACCESSES MAY PREVENT CHARGING COMPLETELY Low Battery State When the battery is running low, a low battery notification message will appear. If you do not respond to the low battery message, the batteries will continue to discharge until they are too low to operate. When this happens, your notebook will go into Sleep mode.
Replacing the Battery With the purchase of an additional battery, you can have a fully charged spare to swap with one that is not charged. O NOT REPLACE THE BATTERY WHEN POWER IS APPLIED TO YOUR SYSTEM HEN REPLACING THE BATTERY MAKE SURE THAT THE NOTEBOOK IS POWERED OFF AND THERE IS NO ADAPTER...
SD Card Slot SD Card Figure 24. Installing a Secure Digital Card Secure Digital (SD) Cards Your LifeBook notebook supports Secure Digital (SD) cards, on which you can store and transfer data to and from a variety of digital devices. These cards use flash memory architecture, which means they don’t need a power source to retain data.
Inserting an SD Card SD Cards are inserted in the SD Card slot. To install an SD Card, follow these steps SD C ’ NSTALLING OR REMOVING AN ARD DURING YOUR OOK NOTEBOOK S SHUTDOWN OR BOOTUP PROCESS MAY DAMAGE THE CARD AND OR YOUR OOK NOTEBOOK O NOT INSERT A CARD INTO A SLOT IF THERE IS WATER OR ANY OTHER SUBSTANCE ON THE CARD AS...
Device Ports Your Fujitsu LifeBook notebook and the External Monitor/LAN adapter cable come equipped with multiple ports to which you can connect external devices including: disk drives, keyboards, printers, etc. The following table indicates the ports on the system and/or the adapter cable.
External Video Port The external video port allows you to connect an external monitor or LCD projector. Note that in order to use a video device directly with the system, you must first attach the included external video/LAN adapter cable. In order to connect an external video device, follow these easy steps: External Monitor/ LAN Adapter...
Headphone Jack The headphone jack allows you to connect headphones or powered external speakers to your notebook. Your headphones or speakers must be equipped with a 1/8” (3.5 mm) stereo mini-plug. In order to connect headphones or speakers follow these easy steps: Align the connector with the port opening.
Chapter 4 Troubleshooting Your LifeBook Troubleshooting There may be occasions when you encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices that can be solved by replacing the device. The information in this section helps you isolate and resolve some of these straightforward issues and identify failures that require service.
Page 66
If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support representative: Toll free: 1-800-8Fujitsu (1-800-838-5487) Web site: http://www.computers.us.fujitsu.com/support. Before you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution: •...
Remove the headphones. Software driver is not The audio driver may be installed or reinstalled using the Drivers and Applications CD that came with your Fujitsu configured correctly. LifeBook. Refer to your application and operating system documentation for help.
Problem Possible Cause Possible Solutions There is no sound coming The speakers have been Click on the Volume icon in the system tray on the bottom from the built-in speaker muted using the Volume icon right of the screen. (It looks like a speaker). If the Mute box (continued) in the system tray.
Problem Possible Cause Possible Solutions Keyboard or Mouse Problems The built-in keyboard does The notebook has gone into Push the Power/Suspend/Resume button. not seem to work. Sleep mode. Try to use your integrated pointing device to restart your Your application has locked out your keyboard.
Problem Possible Cause Possible Solutions You have installed a USB The device may have been Close the application and restart your notebook. device. Your LifeBook installed while an application notebook does not recog- was running, so the notebook nize the device, or the is not aware of its installation.
Page 71
Problem Possible Cause Possible Solutions Your LifeBook notebook The power management Press any button on the keyboard, or move the mouse to turns off all by itself. parameters are set for auto restore operation. If that fails, push the Power/ Suspend/ timeouts which are too short Resume button.
Set the operating source by pressing the [ESC] key while the and displays power on of the setup utility are not Fujitsu logo is on screen or use the [F2] key and enter the information, but fails to compatible with your configu- setup utility and adjust the source settings from the Boot load the operating system.
Problem Possible Cause Possible Solutions An error message is dis- Power On Self Test (POST) See the (POST messages to determine the meaning/severity played on the screen dur- has detected a problem. of the problem. Not all messages are errors; some are status ing the boot sequence.
Problem Possible Cause Possible Solutions The display goes blank by Power management timeouts Press any button on the keyboard, or move the mouse to itself after you have been may be set for short intervals restore operation. If that fails, push the Power/Suspend/ using it.
Power On Self Test Messages The following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual.
Page 76
*Incorrect Drive A type – run SETUP Type of floppy drive A: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.
Page 77
*Operating system not found Operating system cannot be located on either drive A: or drive C: Enter the setup utility and see if both the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you have changed your installation greatly, the operating system should be on drive C:.
Page 78
nnnn Shadow RAM Passed Where nnnn is the amount of shadow RAM in kilobytes successfully tested. *System battery is dead – Replace and run SETUP The BIOS CMOS RAM memory hold up battery is dead. This is part of your BIOS and is a board mounted battery which requires a support representative to change.
PARTY S WEBSITE To re-install drivers and/or applications: Boot up the system and insert the DAR disc after Windows has started. A Fujitsu Installer screen is displayed after the disc is inserted. After reading the License Agreement, click [I agree].
HE COMPONENTS LISTED ARE COLOR CODED IN TERMS OF THEIR INSTALL STATUS LUE INDICATES THAT THE COMPONENT CAN BE INSTALLED REEN INDICATES THAT THE COMPONENT NEEDS TO BE INSTALLED SEPARATELY REY INDICATES A COMPONENT THAT IS ALREADY INSTALLED GREY ITEMS CAN BE REINSTALLED BUT PRIOR TO INSTALLATION YOU WILL RECEIVE A REMINDER THAT THE COMPONENT IS ALREADY INSTALLED...
Your system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. OTE THAT IF YOU HAVE A...
Chapter 5 Care and Maintenance Caring for your LifeBook Notebook If you use your Fujitsu LifeBook notebook carefully, you will increase its life and reliability. This section provides some tips for looking after the notebook and its devices. • HE SYSTEM CONTAINS COMPONENTS THAT CAN BE SEVERELY DAMAGED BY ELECTROSTATIC (ESD).
• Do not attempt to service the computer yourself. Always follow installation instructions closely. • Keep it away from food and beverages. • To protect your notebook from damage and to optimize system performance, be sure to keep all air all vents unobstructed, clean, and clear of debris.
• Always shut down the computer, unplug the power adapter, and remove the battery when cleaning or disinfecting the computer exterior, keyboard or LCD display. Cleaning guidelines using recommended off-the-shelf cleaners Computer exterior, computer keyboard To clean the exterior and keyboard, use one of the following off-the-shelf products: •...
In addition, a faulty battery might damage your LifeBook. • Store your Fujitsu LifeBook in a cool, dry location. Temperatures should remain between 13ºF (-25ºC) and 140ºF (60ºC). Traveling with your LifeBook notebook •...
• Never put your notebook through a metal detector. Have your notebook hand-inspected by security personnel. You can however, put your notebook through a properly tuned X-ray machine. To avoid problems, place your notebook close to the entrance of the machine and remove it as soon as possible or have your notebook hand-inspected by security personnel.
• Keep brightness to the lowest level comfortable. • Set the power management for maximum battery life. • Put your notebook in Sleep mode when it is turned on and you are not actually using it. • Disable the Media Player auto insert notification function. •...
Page 88
Caring for your Optional External Optical Drive Your optional external optical drive is durable but you must treat it with care. Please pay attention to the following points: • The drive rotates the compact disc at a very high speed. Do not carry it around or subject it to shock or vibration with the power on.
Chapter 6 System Specifications Specifications This section provides the hardware and environmental specifications for your Fujitsu LifeBook notebook. Specifications of particular configurations will vary. Configuration Label The configuration label located on the bottom of your notebook contains specific information regarding the options you’ve chosen for your notebook.
Audio • Audio Realtek Codec ALC269 with High Definition (HD) audio. • Stereo headphone jack, 3.5 mm, 400mV or less, minimum impedance 32 Ohms • One built-in speaker, 16 mm diameter, mono • One built-in digital microphone Mass Storage Device Options Hard Drive •...
Keyboard Built-in keyboard • Total number of keys: 75 • Function keys: [F1/F7] through [F6/F12] when used in conjunction with [Fn] key • Two Windows keys: one Start key, one application key • Key pitch: 16 mm; key stroke: 1.2 mm •...
Altitude Operating: 10,000 feet (3,048 m) maximum Popular Accessories For ordering or additional information on Fujitsu accessories please visit our Web site at www.shopfujitsu.com or call 1-800-FUJITSU. Pre-Installed Software Depending on your operating system, your notebook comes with pre-installed software for playing audio and video files of various formats.
Symantec to download latest virus, spyware, and spam definitions. Fujitsu Driver Update Utility The Fujitsu Driver Update (FDU) utility is pre-installed on your system. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. See “Automatically Downloading Driver Updates”...
Page 95
Office Professional 2007! All you need to do is purchase the appropriate Office 2007 license kit which allows you to "un-lock" the full version of Office that you want. ® Fujitsu offers a Media License Kit for Microsoft Office Small Business 2007. Simply enter your product key and you’re ready to go! ®...
Page 96
Microsoft Works 9.0 with Microsoft Office Home and Student Trial Edition 2007 Microsoft Works 9.0 is a software suite containing the basic tools to write letters and reports, track family and friends with address books, manage home finances, and create a home inventory. Microsoft Office Home and Student 2007 is the essential software suite for home computer users that enables you to quickly and easily create great-looking documents, spreadsheets, and presentations, and organize your information in one place, making it easier for you to get things done.
Glossary AC Adapter A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your LifeBook notebook. Access point Wireless network device used to bridge wireless and wired network traffic. ACPI Advanced Configuration and Power Interface Active-Matrix Display A type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.
Page 98
Auto/Airline Adapter A device which converts the DC voltage from an automobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your LifeBook notebook. BIOS Basic Input-Output System. A program and set of default parameters stored in ROM which tests and operates your LifeBook notebook when you turn it on until it loads your installed operating system from disk.
Page 99
CardBus A faster, 32-bit version of the PC Card interface which offers performance similar to the 32-bit PCI architecture. CD-ROM Compact disk read only memory. This is a form of digital data storage which is read optically with a laser rather than a magnetic head. A typical CD-ROM can contain about 600MB of data and is not subject to heads crashing into the surface and destroying the data when there is a failure nor to wear from reading.
Page 100
Default Value A pre-programmed value to be used if you fail to set your own. DHCP Dynamic Host Configuration Protocol. A protocol used to automatically acquire parameters required for the communication, such as IP address. The sender of IP address is called a DHCP server, and the receiver is called a DHCP client.
Page 101
Disk Operating System (MS-DOS is a Microsoft Disk Operating System). Driver A computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment.
Page 102
Gigabyte. One billion bytes. Hard drive A spinning platter of magnetic data storage media where the platter is very stiff. Input/Output. Data entering and leaving your notebook in electronic form. I/O Port The connector and associated control circuits for data entering and leaving your notebook in electronic form.
Page 103
Infrared Light just beyond the red portion of the visible light spectrum which is invisible to humans. Infrastructure A name of a wireless LAN configuration. This type of communication uses an access point. Another type of communication is called Ad Hoc. IP Address An identifier for a computer or device on a TCP/IP network.
Page 104
IrDA Infrared Data Association. An organization which produces standards for communication using infrared as the carrier. Interrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed. Kilobyte. One thousand bytes. Local Area Network.
Page 105
Memory A repository for data and applications which is readily accessible to your LifeBook notebook’s CPU. Megahertz. MIDI Musical Instrument Digital Interface. A standard communication protocol for exchange of information between computers and sound producers such as synthesizers. Modem A contraction for MOdulator-DEModulator. The equipment which connects a computer or other data terminal to a communication line.
Page 106
Network name (SSID: Service Set Identifier) When a wireless LAN network is configured, grouping is performed to avoid interference or data theft. This grouping is performed with “Network name (SSID)”. In order to improve security, the network key is set allowing no communication unless “Network name (SSID)” coincides with the network key. NTSC National TV Standards Commission.
Page 107
POST Power On Self Test. A program which is part of the BIOS which checks the configuration and operating condition of your hardware whenever power is applied to your notebook. Status and error messages may be displayed before the operating system is loaded. If the self test detects failures that are so serious that operation can not continue, the operating system will not be loaded.
Page 108
Reset The act of reloading the operating system. A reset erases all information stored in RAM. Restart See Reset. Resume To proceed after interruption. In your notebook this refers to returning to active operation after having been in one of the suspension states. Read Only Memory.
Page 109
SSID Service Set Identifier, a 32-character unique identifier attached to the header of packets sent over a WLAN that acts as a password when a mobile device tries to connect to the BSS. The SSID differentiates one WLAN from another, so all access points and all devices attempting to connect to a specific WLAN must use the same SSID.
Page 110
TCP/IP Transmission Control Protocol/Internet Protocol. A standard Internet protocol that is most widely used. Underwriters Laboratories – An independent organization that tests and certifies the electrical safety of devices. Universal Serial Bus. Standard that allows you to simultaneously connect up to 127 USB devices such as game pads, pointing devices, printers, and keyboards to your computer.
Regulatory Information Notice Changes or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment. FCC NOTICES Notice to Users of Radios and Television This equipment has been tested and found to comply with the limit for class B digital devices, pursuant to parts 15 of the FCC Rules.
Appendix A: Wireless Device User’s Guide FCC Regulatory Information Please note the following regulatory information related to the optional wireless LAN device. Regulatory Notes and Statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are much less than the electromagnetic energy emissions from wireless devices such as mobile phones.
interference caused by such unauthorized modification, substitution or attachment. The manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failure to comply with these guidelines. This device must not be co-located or operated in conjunction with any other antenna or transmitter. Federal Communications Commission statement This device complies with Part 15 of FCC Rules.
Page 114
003 B / NMB 003 B. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Modifications not expressly authorized by Fujitsu America, Incorporated may invalidate the user's right to operate this equipment.
Before Using the Wireless LAN This manual describes the procedures required to properly set up and configure the integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the manual). Before using the WLAN device, read this manual carefully to ensure it's correct operation. Keep this manual in a safe place for future reference.
Wireless LAN Modes Using this Device Ad Hoc Mode "Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks.
Page 117
Access Point (Infrastructure) Mode Infrastructure mode refers to a wireless network architecture in which devices communicate with wireless or wired network devices by communicating through an Access Point. In infrastructure mode, wireless devices can communicate with each other or with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the WLAN in order to access services, devices, and computers (e.g., file servers, printers, databases).
How to Handle This Device The WLAN device is a device that comes pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The operating system that your mobile computer comes with has been pre-configured to support the WLAN device. •...
Deactivation Using the Wireless On/Off Switch The WLAN device can be deacti- vated quickly and efficiently by toggling the Wireless LAN/Blue- tooth On/Off Switch to the Off position. The switch has no effect on non-Wireless LAN models. The switch is located on the left side of the system WLAN/Bluetooth Switch (Figure 30)
Configuring the Wireless LAN The WLAN device can be configured to establish wireless network connectivity using the software that is built into Windows. Support for most industry standard security solutions is contained in this software. Pre-defined parameters will be required for this procedure. Please consult with your network administrator for these parameters: Configuring the WLAN Using Windows Click the Start button, then select Control Panel.
Troubleshooting the WLAN Troubleshooting Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table. If you are unfamiliar with the steps required, consult your System Administrator or go to [Start] -> Help and Support -> Networking and the Web Problem Possible Cause Possible Solution...
Page 122
Problem Possible Cause Possible Solution Unavailable The computer to Check if the computer to be connected is turned ON. network be connected is connection turned off (continued) RF interference The use of identical or overlapping RF channels can cause interference from Access with the operation of the WLAN device.
WLAN Specifications Specifications Item Specification Type of network The Atheros AR5B91 Wireless network card conforms to IEEE802.11b, IEEE802.11g, and IEEE802.11n, Wi-Fi based* Transfer rate (Automatic switching) 54 Mbps maximum data rate (IEEE802.11n to be determined • Active frequency 802.11n: 2.4 GHz or 5 GHz •...
Page 124
* “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed. ** The communication ranges shown above will increase or decrease depending on factors such as number of walls, reflective material, or interference from external RF sources.
Using the Bluetooth Device The Integrated Bluetooth module (CSR BSMAN3) is an optional device available for Fujitsu mobile computers. What is Bluetooth Bluetooth technology is designed as a short-range wireless link between mobile devices, such as laptop computers, phones, printers, and cameras. Bluetooth technology is used to create Personal Area Networks (PANs) between devices in short-range of each other.
Page 126
Users are not authorized to modify this product. Any modifications invalidate the warranty. This equipment may not be modified, altered, or changed in any way without signed written permission from Fujitsu. Unauthorized modification will void the equipment authorization from the FCC and Industry Canada and the warranty.
Index BIOS guide About This Guide setup utility Bluetooth adapter Boot Sequence plug adapters Booting the System Air Vents Built-in Microphone Application Buttons 1 and 2 Button Functions Auto/Airline Adapter Click Me! Battery clicking care Configuration Label cold-swapping Contact Information conserving power Controls and Connectors dead...
Page 128
Local Area Network (LAN) Error Messages External Monitor/LAN Adapter Cable Connector Media Care External Video Port Polymer Battery Power Fujitsu Contact Information AC adapter Fujitsu Driver Update utility Auto/Airline adapter Fujitsu LifeBook failure cleaning management storing traveling Fujitsu Shopping Online...
Page 129
Status Indicator Panel Battery Charge/DC-In Indicator Regulatory Information Battery Level Indicator Restarting CapsLock Restoring Your Pre-installed Software Hard Disk Drive access indicator Right Button Hard Drive Access Indicator RJ-45 NumLk Power Indicator ScrLk Scrolling Suspend/ Resume button SD Card installing removing Touch Screen 16, 20...
Page 130
Volume Control Warranty Web Camera Windows Power Management Wireless LAN before using characteristics deactivating/disconnecting modes specifications troubleshooting Wireless LAN/Bluetooth On/Off Switch...